SPECIAL REPAIR TO BLDG NO EA-08 PERS COOK HOUSE AND DINING HALL OF MH, AND/ALTN OF BLDG NO. E-91 INCLUDING PROVN OF BATHING POINT SHED AND TOILET BLOCKS FOR MALE AND FEMALE AND PROVN OF ONE TOILET BLOCK NEAR BLDG NO. 157(OFFICE COMPLEX) UNDER AGE B/R

Amount

Dismantling Asbestos cement(corrugated, semi corrugated etc) sheets in roof coverings etc complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for etc complete all as specified and directed

Taking down cement plaster of any description and in any position of brick/concrete surfaces on walls / celing etc. including racking out joints, hacking for key, scrubbing down with water etc & prepared to receive new plaster and disposing off the rubbish off the premises of cantonment complete all as specified and directed.

Dismantiling of stone slabs and tiles (Kota stone etc.) of any discription or any thickness in floors, aprons, skirting, dado etc. laid bedded and pointed in any mortar complete all as specified and directed.

Dismantling floor, hearth or wall tiling of any description and in any position including cement mortar bedding (but not backing) complete all as specified and directed

Demolition of cement concrete of any description and in any position (unreinforced) in ground floors/ paving not exceeding 15 cm thick (below or above GL) and disposing rubbish off the premises of cantonment complete all as specified and directed.

Demolition of RCC of any description and in any position (reinforced) in any position in beams, columns, chajjas and similar situations and disposing rubbish off the premises of cantonment complete all as specified and directed.

Demolition of brick work or stone/ boulder masonry, built in cement mortar including all quoins, pillars etc. complete all as specified and directed

Erection and fixing only mild steel Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc complete all as specified and directed.

S&F Rolled mild structural steel roof trusses (framed), trussed, purlins,posts, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc.conforming to Fe 410-W (Gde-E) all as specified and directed.

S &F for Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates conforming to Gde of steel Fe 410- W (Gde-E250) Quality 'A' also fastening and fixing complete all as specified and directed.

Preparation of new steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coat of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed

Preparation of old painted steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coat of synthetic enamel paint complete all as specified and directed

M & L pre-painted galvalume aluminium zinc coating steel corrugated sheet 0.50 mm thick of any colour having tensile strength 550 mpa as in roof covering/ cladding to wall, fixed with self tapping screws all as specified and directed.

M&L pre- painted galvalume aluminum zinc coating plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof overing/ cladding to wall, ridges, gutters, fixed with self tapping screws complete all as specified and directed.

M & L for PCC 1:4:8 type D-2 (using 40 mm graded stone aggregates) as in foundation filling and mass concrete complete all as specified and direccted.

M & L brick work with fly ash bricks built in CM 1:6 with sub class 'B' bricks straight or curved on plan exc 6 mtr mean radius all as specified.

M&L for brick work with fly ash half brick thick size straight or curved on plan any radius in cement mortar 1:4 complete all as specified and as directed.

M & L for 15 mm thick rendering in cement mortar on fair faces of brick work or concrete surfaces, applied in two layers ie. Ist layer of 10mm thick rendering in CM 1:6 and 2nd(top) layer of 5mm thick rendering in CM 1:4 (top layer mixed with water proofing compound as per manufacturer's instructions) finished even and smooth without using extra cement complete all as specified and directed. (Note:- Water proofing compound shall be measured and paid seperately under appropriate item of Sch 'A' as "supply only")

M&L for preparation of newly plastered surfaces of wall and applying two coats of cement base paint over a coat of alkali resistant primer on walls surfaces complete all as specified and directed

M&L rendering 15mm thick in CM 1:4 on fair faces of brick work or concrete walls finished the surface even and fair without using extra cement complete all as specified and directed.

M&L 10mm thick plastering in CM 1:4 on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed.

M&L for 5 mm thick rendering in CM 1:3 on ceiling surfaces finished even and smooth and including preparation of newly plastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed.

M&L for preparation of newly plastered surfaces of walls and applying two coats of oil bound distemper over a coat of alkali-resiatant primer and 1.5 mm thick Birla wall care putty on plastered surrfaces complete all as specified and directed.

M & L for preparation of newly plastered surfaces of walls and applying three coat of white wash on wall complete all as specified and directed

M & L for complete removal of existing treatment and applying 1.5mm thick birla white wall care putty to fill up the depression and rubbing with sand paper to achieve a levelled and smooth surface and applying two coats of oil bound distemper over a coat of alkali resistant primer on prepared surfaces of internal walls complete all as specified and directed.

M & L for complete removal of existing treatment and applying two coats of cement based paint on prepared surfaces of walls complete all as specified and directed.

M & L preparation of old decorated surfaces of walls plastered or unplastered including removing by brooming down all dust, dirt and all loose scales by steel wire brushing, scrapping down smoke, soots, moulds, moss and efflorescent salts and trading oil and greasy spots etc and applying two coat of Oil bound distemper to walls, white or tinted comlpete all as specified and directed.

M&L preparation of old painted surface of wood and wood based materials of any description not otherwise described over 10 cm. width or girth shall include brooming down or steel wire brushing; scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying one coat of synthetic enamel painting complete all as specified and directed.

M & L 75 mm thick PCC 1:4:8 Type D2 (using 40 mm graded stone aggregate) as in sub bases, floors and pavings etc complete all as specified and directed.

M&L 75 mm thick PCC 1:3:6 type C2 (using 40mm graded stone aggregate) as in plinth protection finished even and smooth without using extra cement complete all as specified and directed.

M&L Reinforced cement concteteType B1, 1:2:4 (20 mm graded stone aggregate) as in foundation, including raft footings, foundation beams, plinth beams, bases for column etc., basement slab, under reamed piles and mass concrete complete all as specified and as directed.

M&L for Reinforced cement concteteType B1, 1:2:4 (20 mm graded stone aggregate) as in Columns, pillars, piers,posts and struts etc complete all as spd and directed.

M&L for Reinforced cement concteteType B1, 1:2:4 (20 mm graded stone aggregate) in slabs supported on walls, beams, landings, balconies, canopies, deck slabs and, shelves and similar works etc complete all as specified and directed.

M&L RCC Type B1 1:2:4 using 20mm graded aggregate (Nominal mix) as in Beams, cantilevers, bressummers, lintels etc. complete all as specified and directed.

M&L for RCC 1:2:4 type B1 using 20mm graded aggregate as in shelves,chajja and the like complete all as specified and directed.

M&L for precast RCC 1:2:4 type B1 (using 20mm graded aggregate) for drain covers incl necessary form work, set in CM 1:4 complete all as specified and directed.

Formwork to sides of concrete foundations, rough finished surfaces of flat concrete, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter,etc complete all as spfd and directed.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) finishing rough finshined flat surface of concrete complete all as specified and directed.

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. finishing rough finished surface of concrete complete all as specified and directed.

Formwork to,rough finished surfaces of concrete,square, rectangular or polygonal, sides of pillars, posts, struts, piers, columns and stanchions,etc complete all as spfd and directed.

Formwork to chullah hoods, chajjas, troughs and similar items including edges finishing rough finshined surface of concrete complete all as specified and directed.

Formwork to,rough finished surfaces of concrete, edges of concrete flats, treads, breaks in floors, window cills, concrete railings,openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide,etc complete all as spfd and directed.

M&L for mild steel TMT bars 10mm dia and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

M&L for Mild Steel TMT Bars 6 to 8mm dia bars cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

M&L for Mild Steel TMT 6 to 8mm dia bars cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia as in stirrups complete all as specified and directed.

M & L Granite (of any type) work (table rubbed and polished) 20 mm thick in steps, jambs, pillars, window-cills, cooking platforms,over 15 mm thick screed bed in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, etc including bull nosing complete all as specified and directed.

M & L for 20-25 mm thick, Machine cut kota stone slab flooring over 20 mm thick cement screed bed in cement mortar 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing etc complete all as specified and directed.

M & L for 20-25 mm thick Kota stone slab over 15 mm thick rendering in cement mortar 1:3 as in backing coat in riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing etc complete all as specified and directed.

Mirror polishing on marble/ granite/ Kota stone/ stone work where ever required to give high gloss finish complete all as specified and directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation,etc.) or insulation boards/slabs/blankets any thickness, incl cover filltets and grids and S & F in true horizontal level false ceiling system, The snap grid shall be of hot dipped galavnised steel sections exposed suface with precoated capping, main tee of size 24x32mm at every 1200mm c/c and cross tee of size 24x27mm (1200mm & 600mm long) at every 600mm c/c and wall angle of size 19x19mm fixed to perimetere wall, as per manufacturer's instructions, grid to be suspended at every 1200mm c/c in both directions by using 3mm dia pre-straightened GI wire at every 1200mm interval at the main tee supported from existing RCC slab fixed with Metal dash fastener including provision of 4mm thick white colour textured designer cement ceiling board (V board) of size 595 x 595 mm fixed with screws/clips complete all as per manufactureres instructions complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutter from the frames) n exc. 1.5 sqm each and removing to or from store complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutter from the frames) exc. 1.5 sqm but n exc 4.00 each and removing to or from store complete all as specified and directed.

M&L 2nd class hard wood plain straight solid chowkats and frames wrought, framed, rounded, chamfered put together with glue pinned joints complete all as specified and directed.

S & F Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required; hooks (stay), heavy, for large gates; hook and pintle hinges; large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts of size25x3MM MS flat; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe 290-0 complete all as specified and directed.

M&L for cement concrete 1:3:6 type CI using 20mm graded stone aggregate in bed black for hold fasts and coping incl necessary form work weathering slightly rounded or chamfered angles and treating and making good the disturbed portion complete all as specified and directed.

M&L 2nd class hard wood plain framed factory made panel shutter 35 mm thick (two or three panels) with lock rail and panel of 12mm veneered particle board with commercial veneering on both faces, the size of rail & style as per IS 1003 (Part-I) Kiln seasoned and chemically pressure treated complete all as specified and directed.

S&F of 35mm thick factory made Glazed and skeleton shutters in 2nd class hardwood open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and directed.

S&F 30 mm thick 2nd class hard wood glazed and skeleton shutter of divided into square, with plain chamfered or rounded metred and rebital sash bar any number and framing moulded windows, ventila-tors, etc. are provided with stiles and rails as specified in SSR Part I, Section 8 clause 8.24 (b) fitted to chowkats complete all as specified and directed.

S & F for powder coated (Thickness of powder coating not less than 50 micron) anodised aluminium frame for doors, windows, ventilators/ grills with one or more rebates including joining cleat for fixing, etc complete all as specified and directed.

M & L for Powder coated (Thickness or powder coating not less than 50 micron) Anodised aluminium window and ventilator shutters,hanging type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws,handles,stoppers etc complete all as specified and directed.

S & F for powder coated (minimum thickness of powder coating 50 micron) aluminium anodised door shutters,aluminium section weighing 0.55 kg/m including necessary joining cleats,glazing clips, ruber neoprene packing,handles 2 Nos in each door, hinges,anodised aluminum snap beading screws, etc complete, as specified and directed.

M & L for Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening all complete as per requirement and direction of Engineer-in-charge.

S&F 5mm thick figured glass fixed in aluminium door/ window/ ventilator with aluminium beading complete all as specified and directed.

S&F 4.0mm thick sheet glass ordinary quality and glazing with wooden beads or oil putty in square not exc. 0.50 Sqm in each pane complete all as specified and directed.

S&F MS Butt hinges medium weight cold rolled of size 100mm complete all as specified and directed

S&F MS Butt hinges medium weight cold rolled of size 75mm complete all as specified and directed

S&F Extruded aluminium alloy handles, fabricated type, anodised of size 150mm complete all as specified and directed

S&F 200mm Aluminium anodised, barrel tower bolts of extruded section and fixed and fixed complete all as specified and directed

S&F for Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed of size 300mm complete all as specified and directed

S & F 300mm, ordinary Mild steel rat tail rod pattern springs including roller and roller plate complete all as specified and directed

S & F 100 mm length of extruded aluminium alloy handles, fabricated type., anodised complete all as specified and directed

S&F 200mm Aluminium anodised, barrel tower bolts of extruded section and fixed and fixed complete all as specified and directed

S&F 140 mm long floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring complete all as specified and directed

S & F stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of apreture 1.0 mm & fixed with stainless steel wire staples fixed complete all as specified and directed

S & F 3mm thick sheet glass ordinary quality and glazing with wooden beads or oil putty in square not exc. 0.50 Sqm in each pane complete all as specified and directed

S & F in repairs 2nd class hardwood exc 13 & n exc 25 sqcm plain fillets, square,rectangular or triangular insection, clean sawn, secured with nails or brads complete all as specified and directed

M&L preparation of new surfaces of wood or wood based material description over 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed

S&F mild steel wire type I, gate & shutter, hooks & eyes 150 mm size complete all as specified and directed

M & L for 18/19mm thick plywood, grade BWR, type BB, fixed with screws to timber frame work for cub board,kitchen cub board and selves and other uses etc complete all as specified and directed

S&F Continuous (piano) hinges, mild steel, bright finish or electro galvanised Width of flaps (when open) in 40mm complete all as specified and directed

M&L for 0.9 mm thick Decorative laminate type I, or surface finish, colour and pattern as approved by Engr-in-charge.

M&L for 1.5mm thick Decorative laminate type I, or surface finish, colour and pattern as approved by Engr-in-charge.

M&L for glazed ceramic coloured tiles in vertical surface 450X300X7mm thick set and and jointed in cement slurry and pointed with white or coloured cement to match , laid over and including 10mm thick rendering in cement mortar(1:4) as backing coat, complete all as specified and directed.

S & F in repair Vitreous china urinal half stall type white with grating and union for discharge pipe(excluding flushing cistern) but including urinal pipe etc complete all as specified and directed

S&F in repair low density poly ethylene pipes (LDPE) of pressure rating 6 kg/ cm2 Bore of pipes in 32mm,as waste pipe etc complete all as specified and directed

S&F in repairs 15 mm dia Stop valves (angle cock), cast copper alloy, fancy type, chromium plated screwed down, high pressure, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

S&F for 15 mm dia Stop valves (angle cock), cast copper alloy, fancy type, chromium plated screwed down, high pressure, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

Supply and fixed in repair 15 mm bore Bib taps cast copper alloy Chromium plated with fancy type, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed

Supply and fixed 15 mm bore Bib taps cast copper alloy Chromium plated with fancy type, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed

S&F sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm including necessary fittings complete all as specified and directed

S & F in 25mm dia CPVC ball valves, screwed both ends for cpvc pipe and fixed complete all as specified and directed

S&F CPVC ball valves, with CPVC lever, screwed both ends to pipes of 20mm bore fixed complete all as specified and directed

Supplying and fixing of 16mm dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and directed

M&L 20 mm dia pipes SDR 11 & Plain CPVC SDR 11 fittings CPVC pipe with all fitting fixed to wall and ceiling in floor complete as specified complete all as specified and directed

M&L 25 mm dia pipes SDR 11 & Plain CPVC SDR 11 fittings CPVC pipe with all fitting fixed to wall and ceiling in floor complete as specified complete all as specified and directed

M&L 32 mm dia pipes SDR 11 & Plain CPVC SDR 11 fittings CPVC pipe with all fitting fixed to wall and ceiling in floor complete as specified complete all as specified and directed

M&L 20 mm dia pipes SDR 11 & Plain CPVC SDR 11 fittings CPVC pipe with all fitting fixed to wall and ceiling in floor complete as specified including taking down existing u/s GI pipe line complete all as specified and directed

M&L 25 mm dia CPVC pipe with all fitting fixed to wall and ceiling in floor complete as specified including taking down existing u/s GI pipe line complete all as specified and directed.

Dismantling of cast iron/AC/PVC pipes 75 mm dia, jointed in cement mortar and taking out of trenches if required complete all as specified and directed

Dismantling of cast iron/AC/PVC pipes100/110mm dia, jointed in cement mortar and taking out of trenches if required complete as specified and directed.

S&F PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches, floors or fixed to walls 110mm bore complete all as specified and directed

S&F PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches, floors or fixed to walls 75mm bore complete all as specified and directed

S&F PVC (SWR) bends any radius 110mm bore complete all as specified and directed

S&F PVC (SWR) bends any radius 75mm bore complete all as specified and directed

S&F PVC (SWR) bends with access door any radius 75mm bore complete all as specified and directed

S&F PVC (SWR) bends with access door any radius 110mm bore complete all as specified and directed

PVC (SWR) junction single, (Single T) equal or unequal 75mm bore with access door complete all as specified and directed

PVC (SWR) junction single, (Single T) equal or unequal 110mm bore with access door complete all as specified and directed

S&F PVC (SWR) vent cowl 110mm bore complete all as specified and directed.

S&F PVC (SWR) floor trap 75mm dia outlet, plain with grating including jointing with solvent cement complete all as specified and directed

M&L for salt glazed stone wave gully traps square or rounded mouthed tape & fix 150 x 150 mm fixed in cement concrete complete all as specified and directed

M&L in repairs salt glazed stone wave gully traps square or rounded mouthed tape & fix 150 x 150 mm fixed in cement concrete complete all as specified and directed

M&L 100 mm thick cement concrete type B2, 1:2:4 (using 40 mm graded stone aggregate) for flooring / footpath / hardstanding finished spike rolling to surface or making impression of expanded metal while the concrete is green complete all as specified and directed.

Dismantling water tanks of capacity 1000 ltr and removing to store and S & F for rotational moulded polythene water storage tank (cylindrical vertical with closed top) Tripple layered (White colour) hoisted 1000 litre capacity and fixed in position all as specified and directed

S & F Ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 20 mm - 210 gms) Bore dia of pipe in 20 mm, etc complete all as specifed and directed.

Supply only integral water proofing compound (BIS Marked)

Supply only integral water proofing compound (BIS Marked)

M&L for Cutting chases in brick wall, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc. and making good, cutting exceeding 10 cm but not exc 20cm girth complete all as specifed and directed.

M&L chequered cement concrete coloured tiles, textured finished of size 250 x 250 x 22 mm/ 300 x 300 x 22 mm thick set jointed in neat cement slurry and pointed with white cement and pigment in floors to match with colour of tiles, over 15mm thick screed bed in CM (1:6) including dismantling of existing tiles complete all as specified and directed.

M&L Vitrified light shade ceramic tiles 10 mm thick (square/ rectanglar ) polished, area of each tile not exceding 0.36 sqm , in floor/wall etc. set and jointed in neat cement slurry and pointed with white or coloured cement to match the surface,laid over and including 15mm thick screed bed or bedding in cement mortar (1:6),complete all as specified and directed.

M&L non skid coloured ceramic tiles 7-8 mm thick (square/ rectanglar ) area of each tile exc 0.06 sqm but n'exc 0.11 sqm in floors etc, set and jointed in neat cement slurry and pointed with white or coloured cement to match the surface,laid over and including 15mm thick screed bed or bedding in cement mortar (1:6) complete all as specified and directed.

M&L for 15mm thick rendering in CM 1:4 with WPC on brick or concrete surfaces finished even and fair and including preparation of plastered surfaces and applying two coats of cement based paint over a coat of alkali resistant primer complete all as specified and directed. (Note: Supply of WPC will be paid under the respective Item)

S&F PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube suppling fixing in opening etc complete all as specified and directed

S&F solid PVC Panel Door shutter 30mm thick style consisting of Frame made out of M.S Tube for top & Bottom rails, MS Frame shall be covered with heat moulded, Plain colour PVC’C’ channel having a PVC Sheets strip of 20mm width struck inside with solvent cement for stiles and plain colour PVC sheets for Top rail, lock rail bottom rail on either side and as gap insert for top rail and bottom rail, paneling of plain colour 5mm thick PVC sheet fitted in the MS Frame, welded/ sealed to stiles and rail with suitable PVC sheet beading and jointed together with solvent cement all as per manufacture instruction complete all as specified and directed

S&F 100 MM Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin,anodised and fixed, type B-21 complete all as specified and directed.

M&L 12 mm thick pre-laminated, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed to aluminium frame with aluminium beading complete all as specified

S&F Brass mortice lock 4 levers, vertical type size 100 mm complete all as specified

S&F Aluminium extruded section Door closer hydraulically regulated designation No 3 universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified

S&F in repairs double action floor spring hudraulically regulated made up of minimum 1.25mm thick aluminium alloy sheet foundation box, main body with stainless steel cover governing pivot made of brass other parts made of mild steel heavy duty complete all as specified and directed.

S&F mild steel 25mm dia,drapery curtain rods powder coated, decorative type complete all as specified and directed.

S&F mild steel, powder coated brackets, decorative type for 25mm dia curtain rods, complete all as specified and directed.

S & F Vitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) complete all as specified and directed

S & F plastic water closet seat , black/white, closed pattern with flat bottom & cover and mild steel chromium plated or aluminized hinging device complete all as specified and directed.

S&F PVC valveless syphonic action type flushing cistern 10 lit capacity low level white with inlet, ball valve, float and handle including brackets and 32mm PVC flush pipe in complete all as specified and directed.

S&F 32mm Dia Unplasticised PVC pipes of pressure rating 10 kgf/cm2 laid for wash hand basin waste pipe complete all as specified and directed.

S & F in repairs Vitreous China wash basin, white, flat back, size 630x450mm including cutting for & pinning in ends of brackets or erracting stand but exclusive of fixing of supply of waste pipe complete all as specified and directed.

Supply and fix wash hand basin Vitreous china white flat back size 550x400mm excluding taps, waste, chain and plug and porcelain stopper but including brackets complete all as specified and directed.

S&F Vitreous china Urinal bowl flat back , size of 465 x 355 x 265mm white (minimum) with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe) complete as directed complete all as specified and directed.

S & F 32mm Waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed complete all as specified and directed.

S & F in repair 15 mm dia Pillar taps fancy type, chromium plated, screwed down high pressure, with lettered ‘Hot' or ‘Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed.

S & F for 15 mm dia Pillar taps fancy type, chromium plated, screwed down high pressure, with lettered ‘Hot' or ‘Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed.

Supply and fix in repair PVC connection 15mm size with PTMT nuts of length 600mm complete all as specified and directed.

Supply and fix PVC connection 15mm size with PTMT nuts of length 600mm complete all as specified and directed.

S&F for Soap dish, vitreous China white, approximate size 160x 160x90mm complete all as specified and directed.

Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and directed.

S&F in repairs 15 mm dia Brass chromium plated shower rose 125 mm size fixed complete all as specified and directed.

S&F in rapairs 15 mm bore two way Bib taps fancy type cast copper alloy chromium plated screwed down, screwed for iron pipe or for brass ferrule Branded Make complete all as specified and directed.

M&L Weather boarding of 2nd class H.W of 20mm to 25mm thick and rebated of thick edge to give 20mm lap and fixed with screws/nails including one coat primer and two coat synthetic enamel paint incl taking down old boards complete all as specified and directed.

Dismantling single layer mangalore pattern or similar tiles laid dry in roofing complete all as specified and directed

M & L roof tiles mangalore pattern interlocking at side joints laid dry complete all as specified and directed

Fixing only roof tiles mangalore pattern interlocking side joints laid dry complete all as specified and directed

Dismantling timber scantlings 40 Sq cm and over in section in any position in framed work complete all as specified and directed

M & L for 2nd class hard wood, clean sawn, in scantiling timber fixed with nails complete all as specified and directed

M & L for Ridge or hip tiles to suit mangalore pattern of roofing tiles, bedded and jointed in cement mortar 1:6, etc complete all as specified and directed

S & F Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, Doo0rs etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive or steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete,Fe 410-W(Gde E-250) Quality A complete all as specified and directed

M&L preparation of new steel surfaces of any description exceeding 10 cm width or girth, when unconnected with other painting or when painted in a different tint and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and directed

Surface excavation n.exc 30cm deep and averagng 15cm deep and getting out Soft/loose soil etc complete all as specified and directed.

Excavation in trenches n.exc 1.5 m wide and n.exc 1.5 m in depth for foundation,etc or for shafts wells, cesspits, manholes, pier holes etc n.exc 10 sqm on plan and n.exc 1.5 m in depth and getting out in soft/loose soil complete all as specified and directed.

Excavation in trenches n.exc 1.5 m wide and n.exc 1.5 m in depth for foundation,etc or for shafts wells, cesspits, manholes, pier holes etc n.exc 10 sqm on plan and n.exc 1.5 m in depth and getting out in Hard/dence soil complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm complete all as specified and directed.

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5m above the starting point in soils complete all as specified and directed

Spreading and levelling in layers n exc. 25 cm thick Add for well ramming including watering as required complete all as specified and directed.

M&L for 25 mm thick Damp proof course in cement concrete 1:2:4 Type B-0 (Using 12.5mm crushed stone aggregate) to horizontal or vertical surfaces including necessary formwork complete all as specified and directed.

M&L for brickwork with sub class B bricks, straight or curved on plan exc 6 m mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L for Half brickwork with sub class B bricks, straight or curved on plan to any radius built in cement mortar 1:4 complete all as specified and directed.

M&L for Hard core broken stone of guage n.exc 63 mm, deposited, spread and levelled in layers n.exc 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

S&F for Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete complete all as specified and directed.

S&F steel ventilator with top hung double shutter including hinges, steel peg stay complete complete all as specified and directed.

S&F Rotational moulded polyethylene water storage tanks Tripple Layered (white) (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I of capacity 500 litres complete all as specified and as directed

S&F Rotational moulded polyethylene water storage tanks Tripple Layered (white) (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I of capacity 1000 litres complete all as specified and as directed

Cutting in to existing manholes for connecting new drains making good to pipe 100mm internal dia and rendering cutting out existing benching for and forming branch channels (1/2 round or 3/4 section)in cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate finished smooth and reforming benching complete all as specified and directed.

S&F galvanized steel water tubing medium grade of 20mm bore complete with all fittings such as bends elbows, tees, short pieces, connectors, back nuts, diminishing pieces, caps and pigs, unions complete all as specified and directed.

All as per item No.173 above but 25mm bore

All as per item No.173 above but 40mm bore

S&F for gunmetal globe or gate valve with iron wheel head screwed both ends for iron pipe of 20mm bore including taking down complete all as specified and directed.

All as per item No.176 above but 25mm bore

All as per item No.176 above but 40mm bore

M & L for cutting of road, hard standing made of concrete or premix carpet, WBM, soiling and morrum filling including excavation for laying of pipe laying all as directed and making good the road/hard standing by using all old/new materials and with PCC (1:2:4) etc, required to match with the existing surface complete all as specified and directed. [Note : Approx width of road cutting is not excedding 30cm]

Cutting/Boring on the existing CI/GI Pipe line 20/40mm dia (in position) for insertion of new GI Tee up to 40mm for branch connection including necessary jointing material complete all as specified and as directed.

Cutting the existing CI Pipe line 100mm dia (in position) for tapping of 25mm GI Pipe for branch connection including necessary jointing material complete all as specified and as directed.

Cutting/Boring on the existing GI Pipe line 20/80mm dia (in position) for insertion of new GI Tee up to 80mm for branch connection including necessary jointing material complete all as specified and as directed.

Excavation in post holes (or similar holes) each not exceeding 0.5 cum, and getting out in soft/loose soil, including returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, watering and removing surplus soil to a distance n exc 50m and making good surface complete all as specified.

M&L for Cement concrete in foundations, filling and mass concrete 1:3:6 type C2 using 40 mm graded stone aggregate as in post hole filling complete all as specified and directed.

M & L PCC (1:2:4), type B0 (using 12.5 mm graded stone aggregate) as in surface channels and drains, finished even and smooth complete all as specified & directed.

M & L PCC (1:2:4), type B1 (using 20 mm graded stone aggregate) as in coping including necessary form work all as specified & directed.

S&F for Brass chromium plated tubular towel rail, 20mm dia, D type, 60CM long between flanges fixed with and including Chromium plated brass screws complete all as specified and directed.

Taking down carefully existing point wiring of any description for (light, fan ,sockets bells etc) complete including fittings such as sunken boxes, switches, sockets, ceiling rose, lamp holders, brackets ,fittings, pendants, fan regulartors etc and making good the disturbed surface of walls, floors etc. all as specified and directed.

Taking down existing sub main wiring /Service wire of any description and size including earth wire, batten, conduits and making good the disturbed surfaces of walls, floors etc. complete all as specified and directed.

M&L Point wiring for one light point/fan point/bell point controlled by one switch with 1.5 sqmm multistrand copper conductor cable PVC (FRLS) insulated unsheathed copper conductor single core multi stand flexible cable and 1.50 sqmm PVC (FRLS) insulated unsheathed copper conductor single core cable ( green colour) as earth lead in and including PVC rigid conduit with all fittings for concealed type on stone/brick, masonary walls, roof etc including new CI/MS sunken box of required size and all as directed by Engineer-in-Charge & 3 mm thick plastic laminated sheet for housing switches sockets, regulators etc. including cutting/running chases, pinning in and making good the disturbed surfaces to match with the existing specification, complete all as specified and directed.

All as per item No.191 but One 5 pin 5/6 Amps switch socket outlet on independent board complete all as specified and directed

All as per item No.191 but One 5 pin 5/6 Amps switch socket outlet on same board complete all as specified and directed

All as per item No.191 but for One 5 pin 15 / 16 Amps switch socket outlet point on independent board with 2.5 sqmm PVC (FRLS) insulated unsheathed copper conductor single core multi stand flexible cable and 2.5 sqmm PVC (FRLS) insulated unsheathed copper conductor single core cable (green colour) as earth lead complete all as specified and directed

All as per item No.191 but for One 5 pin 15 / 16 Amps switch socket outlet point on independent board with 4 sqmm PVC (FRLS) insulated unsheathed copper conductor single core multi stand flexible cable and 4 sqmm PVC (FRLS) insulated unsheathed copper conductor single core cable (green colour) as earth lead complete all as specified and directed

M & L for providing point wiring with 1.5 sq. mm (nominal area) single core PVC insulated FRLS sheathed multi-stranded copper conductor cable (maintaining colour code), 1100 volts grade in and including non metalic rigid PVC conduit medium grade with appropriate size with all fittings (ISI Marked) suitable for concealed wiring on stone/brick, masonary walls, roof etc including modular sunken box of adequate size with suitable modular plate cover for mounting modular switches, sockets, regulators, light fittings etc. complete with all fittings and accessories fixed to wall/ ceiling for one light/ fan /bell point controlled by one oneway modular switches including one run 1.5 sqmm (nominal area) PVC insulated FRLS sheathed multi-stranded copper conductor cable green in colour for earth continuity conductor connected to common earth dolly including cutting/running chases, pinning in and making good the disturbed surfaces to match with the existing specification, complete all as specified & directed

All as per Item No.196 above but one 5 Amps 3/5 pin modular socket outlet on independent board complete all as specified and as directed at site.

All as per Item No.196 above but for one 3/5 pin 5/6 Amps modular socket outlet point on same board with other switches complete all as specified and as directed at site.

All as per item No:196 but for One 3 pin 15 / 16 Amps modular switch socket outlet point on independent board with 2.5 sqmm PVC (FRLS) insulated sheathed copper conductor single core multi stand flexible cable and 2.5 sqmm PVC (FRLS) insulated sheathed copper conductor single core cable (green colour) as earth lead complete all as specified and directed at site.

S&F in repairs switch piano flush type single pole one way 5/6 Amps complete all as specified and directed

S&F in repair switch socket combination flush type 5 Amps Multipurpose 2 in 1, 3 pin/5 pin with porcelain base complete all as specified and directed

S&F Switch socket combination 2 in 1 flush type universal 3 pin 5 & 15 Amps complete all as specified and directed

S&F lamp holder insulated body with back plate suitable for battern fittings complete all as specified and directed

S&F Ceiling rose surface bakelite 65 x 50 mm 2/3 terminals complete all as specified and directed

S&F Fan Regulator (Rotary step type, Switch/Socket type Dimmer) 230/240V, AC complete all as specified and directed.

S&F in repair 9 W LED bulb of base B22d with color temp 6500K complete all as specified and directed.

Supply and fixing Exhaust fan, steel body of sweep 300mm with blades, frame and louvers and its accessories, AC Single Phase 230V complete all as specified and directed.

S&F LED light fitting Mirror type with high output diffuser, 2 Feet, 10Watt, 220V, AC decorative type with driver holder and LED lamp including complete set including necessary connection with three core flexible copper conductor cable of suitable size complete all as specified and directed.

S&F for LED Tube light fitting 20W, 220W, AC, Aluminium extruded channel, decorative type including driver and accessories and including connecting up with twin core twisted flexible PVC copper conduct cabe of 23/0.0076 from ceiling rose complete all as specified and directed.

S&F Sheet metal enclosure MCB distribution board including suitable rated bus-bar single pole and neutral 240V, 8 Ways, double door including taking down of existing sheet metal enclosure complete all as specified and directed.

All as per item No. 210 above but SPN 4 way double door complete all as specified and directed at site.

S&F in repairs factory made prewired TPN 4 ways distribution board (with cable end box) in sheet steel enclouser vertical double door with suitable rated bus-bar,415V suitable for housing TPN MCBs as incomer and SP MCBs as outgoing complete all as specified and as directed.

Supply and fixing 240V, 10 KA 'C' curve miniature circuit breaker (MCB) of SPN and current carrying capacity 6-32 Amp, in the MCB DB complete with connection testing and commissioning complete all as specified and directed.

Supply and fixing 240V, 10 KA 'C' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 6 to 32 AMP, in the MCB DB Complete with connection testing and commissioning complete all as specified and directed.

Supply and fixing 415V 10KA 'B' curve miniature circuit breaker (MCB) of TPN/FP of current carrying capacity 40 to 100 AMP in the DB complete with connection testing and commissioning complete all as specified and directed.

Submain wiring with two single core PVC (FRLS) insulated flexible copper conductor cable of size 4.00 Sqmm and one single core PVC (FRLS) insulated unsheathed flexible copper conductor cable green colour of size 6.0 Sqmm as earth lead in and including PVC conduit medium grade with all fittings suitable for concealed type and making good the disturbed wall surfaces to match with existing specification all as required at site complete with all as specified and directed.

All as per item No.216 above but Sub main wiring using four runs of 6.0 sqmm wire with two runs of 6.0 sqmm earth wire complete all as specified and directed.

S&F in repair fan hook suitable for hanging of ceiling fan made out of MS Flat 40x5mm clamp or 12mm dia round bar duly welded/drilled including nuts, bolts and washers and cutting/chesselling, making good to distrubed surfaces with cement morter 1:3 and matching with existing surfaces by painting complete all as specified and directed.

S&F for 25W energy saving and environmental friendly long life LED Building security street light made up of pressure die cast aluminium housing with high power LED,lens & toughened glass,potted driver , IP 66 protection including connection with twisted unsheathed PVC copper cable of suitable size complete all as specified and directed.

Supply and fixing LED street light fitting 35/36 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and directed.

S &F for 1100 Volts grade heavy duty cable PVC insulated aluminium conductor, served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 Metre apart including 4mm dia suspension wire, one twin core 6 Sqmm flat cable or circular including 40mm GI pipe service bracket complete all as specified and as directed.

S&F in repair single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole 20 Amps MCB complete all as specifed and directed

Earthing complete with galvanized steel earth plate electrode 60cmx60cmx6mm thick buried directly in ground (earth pit not less than 2.25 mtr below ground level) with top edge o the plate not less1.5 mtrs below normal ground level connected to galvanised earth lead wire 4 mm dia by means of bolts nuts, check nuts and washers of galvanized iron of steel all as shown in electrical plate No.3 connected to earthing test point incl necessary earth work, excavation PCC 1:3:6 type CI using 20mm graded stone aggregate for earth chamber provn of PCC cover 40 mm thick 1:2:4 mm type B1 funnel with water Pipe, GI pipe, 15mm dia medium grade protection pipe, GI earth lead complete all as specified and directed.

Disconnecting of old LT Cables from Panel and Shifting of LT Panel from old location to new location of distance not exceeding 50 Mtr including re-fixing and reconnection of LT Cables and construction of PCC (1:4:8) bed of size 4x4 feet complete all as specified and as directed.

Disconnecting, shifting and re-fixing of window AC of Capacity 1.5 TR and re-connecting all necessary electricals complete all as directed

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 10.0 sq mm x 2 core complete all as specified and directed.

All as per Item No.226 but 25.00 Sqmm x 4 Core

All as per Item No.226 but 35.00 Sqmm x 3.5 Core

All as per Item No.226 but 50.00 Sqmm x 3.5 Core

All as per Item No.226 but 70.00 Sqmm x 3.5 Core

S & F cable end termination jointing kit heat shrinkable type for 1.1 KV (earthed) grade cable for outdoor with jointing material and accessories suitable for 3.5 core of size 25 sqmm to 70 Sqmm complete including taking out old unserviceable end termination jointing kit complete all as specified and directed.

S and F cable jointing kit, outdoor heat shrinkable type straight through joint for 1.1 KV (Earthed) grade cable with jointing material and accessories suitable for cable of size 3.5 core 25 to 70 Sqmm including taking out old unserviceable joint kit straight through type complete all as specified and directed.

M & L for road crossing /drain crossing by adopting trenchless tunneling work through specified pipe jacking method by erecting the equipment true to the alignment and gradient by hydraulic pipe jacking technique including tunneling in any type of strata including hard rock, MS cassing pipe heavy duty of size 100mm dia 6mm thick in any length including jointing materials to carry LT UG cables of size upto 240 Sqmm and necesssary conveyance charges of machinery and other required materials in co-ordination with the concerned authorities complete all as specified and directed.

M & L for Indoor cubical type MCCB enclosure and fixing 100A MCCB of suitable size made out of 3.15mm thick CRCA Sheet, single door, front open type and painting with two coats pf powder coated paint over one coat of red oxide primer, MCCB of capacity 100 to 160 Amps with provision for entry & exit of suitable 3.5 Core LT Cable and connecting incoming & outgoing LT Cables complete all as specified and directed. Note: The Scope of work includes removing existing enclosure on the wall with necessary screws, lugs etc and refixing dismantled MCCB in it complete.

Taking down water heater (Electric Gysers) of any type/make of 25/50 Ltrs capacity after disconnecting the exisiting electric wire, water pipe, inserting the inner tank and components for necessary repairs including replacement of underviceable thermostat, heating element, base and apparatus plate assembly, cleaning and removal of scales, servicing etc and re-assembling in all respects after replacing unservicable parts/components and testing for propper working after repairs and fixing in the original place/position duly connecting up water supply and electric supply including civil work for grouting etc and making good to distrubed surfaces with cement morter 1:3 and matching with existing surfaces by painting complete all as specified and directed.

Taking down & refixing of ceiling fan/exhaust fan of any make, sweep and dismantling, cleaning, greasing, overhauling and providing two coats of synthetic enamel paint of exisitng colour and refixing to its exisitng position including connections with new flexible cable 3 Core copper conductor complete after renovation. For ceiling fan-adjustment for providing new down rod including new canopy, clamp, rubber reel, capacitor etc complete all as directed.

Supply and spread approved M-Sand / Robo Sand for cable laying /foundations/Cable duct including watering and consolidation, cushioning of cable laid in trenches complete all as all as specified and directed.

M&L brick protection with common burnt bricks sub class ‘B’ of size 230 x 115 x 75mm for cable protection complete all as specified and directed.

BUILDWEL (BID ID -3127733)