PROVISION OF SQUAD POST FOR TRG OF RECRUITS IN THE MLIRC, PROVISION OF SENTRY POSTCUM LIVING ROOM AT RAIGARH GATE OF MLIRC, SPECIAL REPAIRS TO COMPOUND WALL NEAR SHIVNERI GATE OF THE MLIRC AND SPECIAL REPAIRS TO CHAIN LINK FENCING AT GLOBE AREA

Amount

Surface excavation n. exc. 30 cm deep and averaging 15cm deep and getting out in hard/ dense soil all as specified and directed.

Excavation in trenches n. exc. 1.5 m wide and n. exc. 1.5 m depth for foundation, etc. and getting out in soft/ loose soil all as specified and directed.

Excavation in trenches n. exc. 1.5 m wide and n. exc. 1.5 m depth for foundation, etc. and getting out in hard/dense soil all as specified and directed.

Excavation in post holes n.exc 0.5 cum in hard/ dense soil, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around in layers n.exc 25 cm watering and removing surplus soil to a distance n.exc 50 m and making good surface all as specified

Returning filling in including spreading levelling, watering and well ramming in layers n. exc. 25 cm thick all as specified and directed.

Removing excavated soil n.exc 50 m and depositing where directed at a level n. exc. 1.5 m above the starting point in soil all as specified and directed.

M&L for hard core with broken stone or boulders of gauge n.exc 63mm, deposited, spread, levelled in layers n.exc 15cm thick, watered and rammed to a true surfaces all as specified and directed.

M&L Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering complete all as specified and as directed.

M&L for plain cement concrete 1:4:8 type D2, using 40mm graded stone aggregate in foundation, filling, mass concrete, levelling courses and sub bases all as specified and directed.

M&L for plain cement concrete 1:3:6 type C2, using 40mm graded stone aggregate in foundation, filling, mass concrete, levelling courses and sub bases all as specified and directed.

M&L for pre-cast cement concrete solid block masonry, exc 10cm width, blocks cast in PCC 1:3:6 type C0, using 12.5mm graded stone aggregate, set in CM 1:6 complete all as specified and directed.

M&L plain cement concrete 1:2:4, type B0, using 12.5mm graded stone aggregate as in coping, bed blocks, eves filling between wall and tile/ sheet roofing including necessary form work all as specified and directed

M&L for plain cement concrete 1:3:6 type C1, using 20mm graded stone aggregate in drains, copings, etc. including necessary form wok and moulds all as specified and directed.

M&L for plain cement concrete 1:3:6 type C1, using 20mm graded stone aggregate as in surface channels and drains concrete all as specified and directed.

Extra for forming fair finished drain or channel of 45cm inner girth in cement concrete using extra cement including forms moulds mitred / stopped end etc. all as specified and directed.

Extra for forming fair finished drain or channel of 30cm inner girth in cement concrete using extra cement including forms moulds mitred / stopped end etc. all as specified and directed.

M&L for providing precast cement concrete 1:2:4, type B1, using 20mm graded stone aggregate as in cover slabs, etc. set in CM 1:6 all as specified and directed.

M&L for providing precast cement concrete 1:2:4 type B-l, using 20mm graded aggregate) as in spacer bands in drain, average sectional area n exc 100 sq. cm, with or without chamfered angles and flat, splayed, rounded or mitred tops as directed and fixed all as specified and directed.

M&L for Reinforced cement concrete 1:2:4, type B1, using 20mm graded stone aggregate as in foundation, column footings, plinth beams, etc all as specified and directed.

M&L for Reinforced cement concrete 1:2:4, Type B1 using 20mm graded stone aggregate as in beams, cantilevers, bressummers, lintels over 1.5m span and the like all as specified and directed.

M&L for Reinforced cement concrete 1:2:4, Type B1 using 20mm graded stone aggregate as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, and in shelves and the like all as specified and directed.

M&L for Reinforced cement concrete 1:2:4, Type B1 using 20mm graded stone aggregate as in Columns, pillars, piers, posts and struts and the like all as specified and directed.

Supply only approved integral water proofing compound all as specified and as directed.

M&L for use of form work to sides of concrete foundations, column footings, plinth beams and similar works for rough finished flat concrete surfaces, vertical or to batter, all as specified and directed.

M&L for use of form work to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work not exc. 200m thick (Horizontal or sloping), flat rough finished surfaces of concrete all as specified and directed.

M&L for use of form work to sides and soffits of roof beams, tie beams, lintels, and similar works for rough finished flat concrete surfaces all as specified and directed.

M&L for use of form work to sides of pillars, posts, struts, columns, etc. for fair finished concrete surfaces, square, rectangular or polygonal all as specified and directed.

M&L for 2nd class hard wood chowkhat or frames, plain, solid, wrought, framed and rebated on the solid rounded or chamfered, put together with glue pinned at joints, fixed in position all as specified and directed.

M&L for 35mm thick 2nd class hard wood glazed/ gauged shutters, open rebated and prepared to receive glass, gauze, etc. (divided into square with plain, chamfered or rounded, mitred and rebated sash bars any numbers), edge of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8. clause 8.24 (a) and fitted to chowkats all as specified and as directed.

M&L for powder coated aluminium frame work as in doors, partitions and windows using standard aluminium extruded sections with thickness of powder coating not less than 50 microns including provision of glazing clips, hinges, handles, etc all as specified and as directed. Notes: (i) All the aluminium sections provided under this item shall be measured and converted into weight for payment with the designated unit weight mentioned in the manufacturer's catalogue for the corresponding aluminium sections/ fittings. (ii) The rate quoted deemed to include necessary grouting/ embedding of the aluminium frames/ supports into floors/ walls and making good the disturbed surfaces to match with the existing surfaces and provision of necessary rubber gaskets. (iii) Particle board/ glass panels shall be measured and paid separately.

S&F MS butt hinges 100mm in size, medium weight, cold rolled all as specified and directed.

S&F aluminium anodised handles, 150mm in size, fabricated type, all as specified and directed.

S&F aluminium anodised barrel tower bolt 200mm size all as specified and directed.

S&F 300mm long aluminium anodised sliding door bolt with hasp, staple (bolt type) and fixing clip of sheet cast or extruded section and fixing bolts plate type with bright bolt not less than 12mm dia all as specified and directed.

M&L for mild steel TMT bars 8mm dia and over cut to length bent to shape required including cranking bending, spirally for hooping for column, hooking ends and binding with and including MS wire (annealed) not less than 0.9mm dia all as specified and directed.

All as described in item No.35 but 6mm dia and over upto and including 10mm dia in stirrups, spacers and binders.

M&L for mild steel framed work as in gates of angle or other section with gusset plate, rails, braces etc complete, prepared for hanging or sliding with and including either hook or hinges and hanging fastening and fixing complete conforming to Fe 410W (Gde E-250) all as specified and directed.

S&F mild steel works in tubular trusses, rafters, purlins, etc. including special shaped washers etc. complete using ERW or induction butt welded tubes conforming to IS.1161-1979 grade St.-240 all as specified and as directed.

S&F hand rails, half round or other stock section, drilled and countersunk for balusters, balusters including embedding in concrete and screwing etc. wind ties for roof including securing bolts and similar work conforming to Fe-290 Gde E-165 all as specified and as directed.

M&L for rolled mild steel sections as in main and cross beams, hip and jack rafters, purlins where connected to common rafters, fixed with angle cleats or other connecting plates conforming to Fe-410-W Gde-E-250 quality-A all as specified and as directed.

S&F mild steel works in tubular trusses, rafters, purlins, etc. including special shaped washers etc. complete using ERW or induction butt welded tubes conforming to IS.1161-1979 grade St.-240 all as specified and as directed.

S&F mild steel framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; frame work of water tanks and similar work conforming to Fe-290 Gde- E-165 all as specified and as directed.

M&L for rolled mild steel posts and struts in fencing and similar work conforming to Fe-290 Gde E-165 including cutting tops to shape as directed, drilling holes, notching for wire, etc. flat iron fillets for securing wire mesh etc. all as specified and as directed.

Supply only chain link fencing, any mesh, size and type all as specified and directed.

Fixing only chain link fencing including line wires, any mesh, size and type, fixed to any type of standards, rails, straining bolts, etc. including provision of binding wire all as specified and directed.

M&L for mild steel flats for securing chain link fencing including securing bolts and similar works, conforming to Fe-290 Gde E-165 all as specified and as directed.

S&F Mild steel screw bolts (machine made), n exc 5cm long and 5 to 10mm dia neck with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, all as specified and as directed

S&F Mild steel screw bolts (machine made), n exc 5cm long and 11 to 15mm dia neck with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, all as specified and as directed

M&L for pre-painted galvalume coated high tensile corrugated/ trapezoidal profile steel sheets, AZ-70 coating mass, 550 Mpa yield strength, 0.5mm thick (TCT), as in roofing/ cladding fixed with self drilling fasteners as per manufacturers instructions all as specified and as directed. Note: Measurement shall be taken flat as fixed without any allowance for laps, etc.

M&L for pre-painted galvalume coated high tensile plain profile steel sheets, AZ-70 coating mass, 550 Mpa yield strength, 0.5mm thick (TCT), as in ridges, valleys, hips, claddings, etc. fixed with self drilling fasteners as per manufacturers instructions all as specified and as directed. Note: Measurement shall be taken flat as fixed without any allowance for laps, etc.

M&L for providing roof treatment with APP modified water proofing membrane with the following specifications all as specified and directed.

Preparing the top surface of RCC slab by removing dust, dirt, etc. and brushing with neat cement slurry @ 3Kg/Sqm on cleaned RCC slab surfaces and rendering 10 mm thick in CM 1:3 mixed with water proofing compound and finishing surfaces even and smooth without using extra cement. Note: Water proofing compound shall be measured and paid separately

Preparation of plastered surfaces by removing dust, dirt & applying oil bound bituminous primer at 0.3 litre per Sqm & providing APP modified water proofing membrane weight not less than 4.5kg/ sqm reinforced with non oven polyester mat weight not less than 160gms per Sqm including minimum 10cm side/ over laps & including applying a coat of blown hot bitumen grade 85/25 over membrane at 1.2kg per Sqm & on drying applying a coat of solar reflective bituminous aluminium paint at 0.1kg/sqm.

NOTE: APP modified water proofing membrane shall be of any one of the approved makes as specified here-in-after and shall conform to specifications given IS 16540-2017/ IS 16532-2017. Contractor shall produce necessary test certificate of the manufacturer to the Engineer-in-charge before incorporation in the work. Necessary independent tests shall also be carried out by the contractor without any extra cost to the Deptt as per relevant IS specifications and membranes with satisfactory test results shall only be incorporated in the work.

M&L for 75mm thick plain cement concrete 1:4:8 type D2 using 40mm graded stone aggregate as in sub base for flooring including finishing the surface even and fair all as specified and directed.

M&L for 100mm thick plain cement concrete 1:4:8 type D2 using 40mm graded stone aggregate as in sub base for flooring including finishing the surface even and fair all as specified and directed.

M&L for 50 mm thick plain cement concrete 1:2:4 type B1 using 20mm graded aggregate as in floor, finished even and smooth with using extra cement all as specified and directed.

M&L for 50 mm thick plain cement concrete 1:2:4 type B0 using 12.5mm graded aggregate as in wearing surfaces of surface channels and drains finished even and fair all as specified and directed.

M&L for 75 mm thick plain cement concrete 1:2:4 type B1 using 20mm graded aggregate as in pavings finished even and smooth and making impression of expanded metal while concrete is green all as specified and directed.

M&L for forming 12mm thick Expansion joints filled with pre-formed bituminous filler and top 30mm primed and sealed with sealing compound, Grade ‘A’ for 50 mm thick concrete slab all as specified and as directed.

M&L for coloured matt finished ceramic tiles, edge cut, 9 to 10mm thick area of each tile exc 0.18 Sqm but not exc 0.38 Sqm, in floors, etc. set and jointed in neat cement slurry and pointed in white cement mixed with colouring pigments to match the shade of the tile laid over and including 15mm thick screed bed in cement mortar 1:4 all as specified and directed.

M&L for coloured decorative cement concrete tiles 30cm x 30cm x 25mm thick, with glossy/ rubber moulded finish on top, set jointed and pointed in neat cement slurry, laid over and including 15mm thick screed bed in cement mortar 1:6 as in pathways, etc. complete all as specified and directed.

M&L for plain cement concrete 1:3:6, type C1, using 20 mm graded stone aggregate, 75mm thick as in plinth protection, finishing the surface fair and even, in panels & filling joints with mortar etc. complete all as specified and directed.

M&L for rendering 5mm thick in cement mortar 1:3 on soffit of roof ceiling, finished even and smooth without using extra cement complete all as directed.

M&L for rendering 10mm thick in cement mortar 1:6 on fair faces of brick work or PCC block masonry or concrete surfaces finished even and smooth without using extra cement complete all as directed.

M&L for rendering 10mm thick in cement mortar 1:4 on fair faces of brick work or PCC block masonry or concrete surfaces finished even and smooth without using extra cement complete all as directed.

M&L for rendering 15mm thick in cement mortar 1:4 on fair faces of brick work or PCC block masonry or concrete surfaces finished even and smooth without using extra cement complete all as directed.

M&L for rendering 5mm thick in cement mortar 1: 4 mixed with water proofing compound over 10mm thick backing coat in cement mortar 1:6 on fair faces of brick work or PCC block masonry or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed. Note: Water proofing compound shall be measured and paid separately.

M & L for 5mm thick sheet glass ordinary quality and glazing with oil putty/ neoprene beading in square n. exc 0.5 sqm in each pane all as specified and directed.

M&L for three coats of white wash on newly plastered surfaces of ceilings including necessary preparation of surfaces all as specified and as directed.

M&L for two coats of oil bound distemper (Acrylic distemper washable), any colour, over a coat of primer on newly plastered walls, pilasters, cornices, etc., including necessary preparation of surfaces with chalk whiting all as specified and as directed.

M&L for two coats of cement based paint, any colour, on newly plastered surfaces of walls, pilasters, cornices, etc., over a coat of primer including necessary preparation of surfaces all as specified and directed.

M&L for two coats of weather proof exterior acrylic emulsion paint over a coat of alkali resistant primer on newly plastered surfaces of walls, pillasters, roof projections, facias, drops, chajjas, etc., including necessary preparation of surfaces all as specified and as directed.

M&L for preparation of new wooden surfaces over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer all as specified and directed.

M&L for preparation of new steel surfaces over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer all as specified and directed.

M&L for preparation of new steel surfaces not exc 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer all as specified and directed.

M&L for 2000 litres capacity rotational moulded polyethylene (HDPE) water storage tanks, 'ISI' marked, cylindrical, vertical with closed top conforming to IS 12701-1989 having two layers wall construction with manhole lid and suitable locking arrangement including making holes for inlet, outlet and over flow pipes, hoisted and fixed in position including testing complete all as specified and directed.

S&F 50mm bore gun metal gate valve heavy duty ISI marked with iron wheel head screwed both ends to iron pipes and fixed all as specified and as directed

S&F 25mm bore gun metal gate valve heavy duty ISI marked with iron wheel head screwed both ends to iron pipes and fixed all as specified and as directed

S&F 25mm dia PTMT ball valves high pressure with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe all as specified and directed.

S&F 25mm bore galvanized iron tubes, medium grade, with all fittings, fixed complete to walls, ceilings or laid in floors all as specified and directed.

M&L for 600mm bore Reinforced cement concrete pipes, class NP2, laid and jointed complete with collars including demolition and all as specified and as directed.

M&L for bed concrete to 600mm bore drain pipes in Plain Cement Concrete 1:3:6 type D2 using 40 mm graded stone aggregate including packing under and haunching against the sides of pipe after they are laid and tested all as specified and directed.

Demolition of PCC solid block masonry built in cement mortar pillars, etc. in any position below or above ground level all as specified and directed.

Dismantling posts or struts (wood, steel or RCC.) any section, including taking out embedded portion and making good disturbed ground all as specified and directed.

M&L for Point wiring complete with 1.5 Sq mm single core PVC insulated FRLS unsheathed 1100 volt grade copper conductor multi-stranded cables drawn through and including ISI marked PVC conduit/ casing capping of suitable size and all necessary fittings and provision of one run of PVC insulated FRLS unsheathed 1100 volt grade copper conductor multi-stranded single core cable of size 1.5 sqmm and connected to common earth dolly including 2nd class HW board fixed on wall/ pillars with sunmica top for mounting switches/ sockets etc. for one light point controlled by one switch 1 way complete all as specified and directed. all as specified and directed.

All as described in item No. 83 but for one fan/ exhaust fan point controlled by one switch and regulator.

All as described in item No. 83 but for one 05 Amps socket outlet on independent board.

All as described in item No. 83 but for one 05 Amps socket outlet on the same board with other switches.

M&L for concealed point wiring complete with 1.5 Sq mm single core PVC insulated FRLS unsheathed 1100 volt grade copper conductor multi-stranded cables drawn through and including PVC conduit pipes and provision of one run of PVC insulated FRLS unsheathed 1100 volt grade copper conductor multi-stranded single core cable of size 1.5 sqmm and connected to common earth dolly including provision of suitable GI modular box flush mounted with wall alongwith modular frame and white cover plate for mounting modular switches/ sockets etc. for one light point controlled by one switch 1 way complete all as specified and directed. all as specified and directed.

All as described in item No. 87 but for one fan/exhaust fan point controlled by one switch and regulator.

All as described in item No. 87 but for one 05 Amps socket outlet on independent board.

All as described in item No. 87 but for one 05 Amps socket outlet on the same board with other switches.

All as described in item No. 87 but wiring with 4 Sqmm single core PVC insulated FRLS unsheathed 1100 volt grade multi-stranded copper conductor cable and with one run of single core PVC insulated FRLS unsheathed 1100 volt grade multi-stranded copper conductor cable of size 4 Sqmm for earth continuity conductor and connecting to common earth dolly, complete for one 15 Amps power socket point on independent board all as specified and directed.

S&F in switch piano flush type single pole, 5 Amps 230 volts all as specified and directed.

S&F in socket outlet 2 in 1, 5 Amps 3 and 2 pin flush type all as specified and directed.

S&F modular switch, 1 module, 1 way, 6 Amps, 230 volts, AC, all as specified and directed.

S&F modular switch, 1 module, 1 way, 16 Amps, 230 volts, AC, all as specified and directed.

S&F modular socket outlet, 2 module, 6 Amps 2 cum 3 pin multipurpose all as specified and directed.

S&F modular socket outlet, 2 module, 16 Amps 3 pin 16 Amps cum 3 pin 5 Amps multipurpose all as specified and directed.

S&F in ceiling rose 3 terminal suitable for 230 volts AC supply all as specified and directed.

S&F modular fan regulator, step type, 2 module, 120 Watts, 230 volts, AC, all as specified and directed.

S&F in repairs, MCB DB SPN 2 Way without bus bars single door type and including provision of 2nd class hard wood board with sunmica top of suitable size fixed to wall and fixing of the MCB DB on board complete all as specified and directed.

S&F in repairs, MCB DB SPN 8Way without bus bars single door type and including provision of 2nd class hard wood board with sunmica top of suitable size fixed to wall and fixing of the MCB DB on board complete all as specified and directed.

S&F MCB SPN 6-32A 10KA 50Hz 240 Volts AC supply all as specified and as directed.

S&F MCB SP 6-32A 10KA 50Hz 240 Volts AC supply all as specified and as directed.

S&F surface mounting LED light fitting, 1x 20W, 230V, wall/ ceiling mounted type, with extruded aluminium housing and polycarbonate diffuser, 20W LED strip, integrated electronic driver and all accessories internally pre wired complete and connecting up light fitting with twin core twisted flexible copper conductor cable of suitable size from ceiling rose to connector block and provision of 2 Nos. of PVC square blocks all as specified and directed. Make: HAVELLS LUMILINE PLUS or equivalent in CG/ Philips/ Wipro

S&F 25 Watts LED security light fitting, with pressure die cast aluminium housing and lens embedded PC cover having top opening separate driver compartment with IP65 protection, 25 Watts high power LEDs, electronic driver including all accessories internally pre wired complete and connecting up light fitting with twin core twisted flexible copper conductor cable of suitable size from ceiling rose to connector block including provision of bracket made out of GI pipe light grade of suitable size and length and bent to shape fixed to walls/ poles with suitable MS clamps, bolt, nuts etc. complete all as specified and directed. Make: ENDURA PEARL model of HAVELLS or equivalent in Crompton Greaves/ Philips/ Wipro

S&F ceiling fan, 230 volts, single phase, 1200mm sweep, Star rating with all accessories including provision of suitable size down rod for hanging of fan complete all as specified and as directed. Make: HAVELLS Model No. ES-50 or equivalent model in makes CG/ ORIENT

S&F exhaust fan, 300mm sweep, 230/240 Volts, 1350 RPM, single phase, metallic finish powder coated, with wire grid protection and fixing arrangements with fixing bolts and provision of 3 core flexible copper conductor cable of size 1.5sqmm size from ceiling rose to connector of exhaust fan and testing all as specified as directed. Make: Havells VENTL-AIR DSP model or equivalent model in Almonard/ Crompton Greaves

S&F storage type water heater (Geyser), 50 litres capacity, 2 KW, vertical type including drilling holes into wall, provision of 4 Nos of suitable size anchor bolts, nuts and washers, 2 Nos. of PVC connections 450mm long, brass Non return valve connecting up electrical & water supply lines, testing and making good disturbed surfaces complete all as specified and as directed. Make: MONZA DX Model of HAVELLS or equivalent model in RACOLD/ USHA/ CROMPTON GREAVES

M&L for XLPE insulated, armoured, heavy duty electric LT UG cable with multi-stranded aluminium conductor, 1100 Volts grade, cross sectional area 10 Sqmm x 4 core, laid in trenches/ passing through pipe/ duct or fixed to wall including provision of necessary lugs/ thimbles/ ferrules, connecting up , testing and commissioning complete laid in repairs all as specified and as directed. Note: Excavation, earth work, cable cushioning, bricks/ GI pipe for protection shall be measured and paid separately under relevant items of this schedule.

All as described in item No. 109 but cross sectional area 25Sqmm x 4 core

M&L for double wall corrugated HDPE pipes, conforming to IS 14930-2001, ISI marked, 63mm outer dia, as in cable protection, fixed to poles/ walls with necessary MS clamps, bolts, nuts, washers or laid in trenches/ under roads/ crossing etc. all as specified and as directed.

M&L for GI tubes, light grade, 40mm bore, as in cable protection, fixed to poles/ walls with necessary MS clamps, bolts, nuts, washers or laid in trenches / under roads/ crossing etc. all as specified and as directed.

Earthing complete with galvanised steel earth plate electrode 60cmx60cmx6mm thick, burried directly in ground vertically (earth pit not less than 2.25 metre deep below normal ground level) with top edge of the earth plate at a depth not less than 1.5m below normal ground level connected to GI wire 4mm dia (7.5m long) by means of GI bolts nuts washers and GI wire protected by 15mm dia light grade GI pipe (7.5m long) and watering arrangements with 20mm dia GI pipe medium grade and GI funnel all as specified and shown in Electrical Plate No 3 of MES Schedule Part I including necessary excavation and earth work in any type of soil, charcoal, dust salt, PCC 1:2:4 type B1 in chamber, 40mm thick RCC 1:2:4 type B1 in cover slab with 8mm dia TMT bars at 100mm C/C both ways and with 8mm dia MS hook complete and testing all as specified and directed.

A. N. Kalbhavi