PROVISION OF ADDL TOILET BLOCKS UNDER GE (AF) LOHEGAON AT AIRFORCE STATION PUNE

Amount

Surface excavation not exc. 30 cm deep and averaging 15 cm deep and getting out in soft / loose soil complete all as specified and directed.

Earth work in excavation by mechanical means (Hydraulic excavator)/in all kind of soil for foundation trenches or drains (not exceeding 1.5 m in width or 10 Sqm on plan),including dressing of sides and ramming of bottoms,lift upto 1.5m,including getting out the excavated soil and disposal of surplus excavated soil as directed,within a lead of 50 m complete all as specified and as directed

M&L for PCC 1:4:8 type D2 (Using 40mm graded stone aggregate) as in foundation, filling and mass concrete.

M&L pre-cast cement concrete(20mm graded crushed stone aggregate) 1:3:6 type C-1 as in block masonery exc 10cm in width with solid block masonery with solid blocks,exc.10cm in width and setting in cement mortar 1:4 all as Specified

M&L for Providing precast cement concrete (20mm graded stone aggregate) 1:3:6 type C-1 as in solid building blocks 10cm thick setting in cement mortar,1:4 complete, in walls all as specified.

M&L TMT bars 10 mm and over cut to length, bent to shape required incl cranking, bending spirally for hoping for columns hooking ends and bindind with ms wire (annealed) not less than 0.9mm dia quality confirming to all as specified

Ditto all as per ser Item No. 6.00 above but, 5 mm dia and over and incl 10mm dia in stirrups, spacers and binders

M&L for Mild steel TMT bars 8mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hoping for columns, hooking ends and binding with and includeing mild steel wire (annealed) not less then 0.9mm dia or securing with clips as specified

M & L for Form work to sides of concrete foundations ,footings , bases of columns ,raft and raft beams , sides and soffits ( if any) of foundation and plinth beams and similar vertical or to a batter flat rough finished surface

M & L for Form work to sides of pillars , posts , struts , piers , columns and stantions rough finished surface square , rectangular or polygonal

M&L form work to sides and soffits of roof beams, lintels lever shelves incl supports over hang etc fair finished surfaces of concrete flat all as specified

M&L form work to soffits of suspended slabs such as roof slab landings and similar works n exc 200mm thick (horizontal or slopping) fair finished surfaces of concrete flat all as specified

M&L form work to edges of concrete flates ,treads break in floors ,window cills ,concrete railings , openings in concrete walls, floor and roofs n exc 20 cm wide and sisides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10 cm

M&L for Reinforced cement concrete M 25 using 20mm crushed stone as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed.

M&L for reinforced cement concrete M 25 using 20mm crushed stone aggregate as in columns ,pillars piers ,posts and struts

M&L for reinforced cement concrete M 25 using 20mm crushed stone aggregate as in beam, cantilever,bressumers, lintel over 1.5 mtr span concrete flat all as specified.

M&L for reinforced cement concrete M 25 using 20mm crushed stone aggregate as in roof slabs supported on walls surfaces of concrete flat all as specified.

M&L hard core of gauge exc 63mm but not exc 100 mm depoted ,spread and levelled in layers not exc 15 cm thick watered and rammed to a true surface broken stone or boulders

M&L for 100mm thick PCC 1:4:8 type D2 (Using 40mm graded stone aggregate) as in sub base

M&L 40mm thick PCC 1:2:4 type B1 using 20mm graded stone aggregate as in flooring complete all as specified and as directed.

M&L for Sand filling under floors or in foundations including watering and consolidation

M&L for rendering 10mm thick on fair faces of brick work or concrete surface in CM 1:6 and rendering is to be finish even and smooth with out using extra cement.

M & L for rendering 15mm thick two layers in cement mortar (10mm thick in 1:6 and 5mm thick in 1:4) on fair faces of brick or concrete surfaces and including mixing water proofing compound as per manufactureres instructions complete all as specified and directed. Note :- Water proofing compound shall be measured and paid for seperately under appropriate item of Sch "A' as supply only. complete all as specified and directed.

Supply only liquid water proofing compound (ISI Mark) complete all as specified and directed.

M&L for 5mm thick rendering on concrete surface of ceiling in CM 1:3and rendering is to be finished even and smooth with out using extra cement

M & L three coats of white wash on newly plastered wall surfaces including preparation of surfaces.

M&L for two coats of cement base paint over a coat of primer on newely plaster surfaced of walls including preparation of newly surface.

M & L three coats of white wash on newly plastered ceiling surfaces including preparation of surfaces.

M&L for Powder Coated (Minimum thickness of powdercoating 50 micron) Anodised aluminium frame of standerd section for doors, windows, ventilators and partitions with double rebates including joining cleat for fixing etc. complete all as specified

S & F Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-charge (For sliding window )

M&L sheet glass 4.0mm thick figured glass, pin head type and glazing with aluminium beeds in square exc 0.50 sqm in each pane complete all as specified and as directed

S&F in for Glavanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperature 1.18mm and fixed complete all as specified and directed.

S&F rotational moulded polyethylene water storage tank consisting of three laver cylindrical vertical with top closed hoisted and fixed in position all as specified and directed capacity 1000 ltrs.

S&F 20 mm dia gun metal ,globe or gate valves, with iron wheel head, screwed both ends for iron pipe

S&F 20 mm dia Ball valves ,high pressure with polythene float and flynut complete screwed for iron pipe or brass ferrule

S&F 15mm bore bib tap cast copper alloy chromium plated butterfly handle screwed down screwed for iron pipe completed

S &F Two way bib cock with wall flange 15mm dia all as specified and directed.

S&F Angle stope valves, cast copper alloy, screwed down high pressure with crutch or butter fly handle, fancy type, chromium plated 15mm bore dia of pipe. complete all as directed by Engr-in-charge.

S&F PVC connection 15mm bore length not less than 450 mm long with both ends PTMT nuts complete all as specified.

S&F pillar tap cost copper alloy with captain heads chromium plated screwed down high pressure with or without (Hot or Cold) with long screwed shanks and fly nuts screwed for iron pipe 15mm bore

S&F WHB vitreous China white, flat back of size 550x400mm incl brackets fixed all as specified and directed.

S & F waste coupling of PTMT 32mm bore for urinal / wash basin (Half or full threaded ) (Minimum Weight 45 grams)

S & F Chromium plated shower roses 125mm size with or without swivel joints any size including fixing to steel pipe or union all as specified and directed.

S&F stop valves, cast copper alloy, screwed down high pressure with crutch or butter fly handle, fancy type, chromium plated with long shank and cup (concealed type), 15mm bore dia of pipe. complete all as directed by Engr-in-charge.

S & F Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified.

S&F Vitreous china wash down water closet scouting pattern, white (EWC) including Plastic seat of same colour of WC, closed patttern with flat bottom, and cover and Mild steel chromium plated hinging device including trap set and necessary concrete complete.

S&F 10 litres capacity PVC valveless syphonic action type, flushing cistern (ISI marked), low level with inlet, ball valve, float bracket & flush pipe complete all as specified & directed.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof,water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). ® Note: For WPC solid door/window frames,minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. (Note: including stainless steel butt hinges and necessary S S screws)

S&F, 200 mm long aluminium anodised barrel barrel tower bolts of extruded section and fixed as specified and as directed.

S&F, 125 mm aluminium handles cast type, anodised complete all as specified and as directed.

S&F vitreous China urinal Half stall type, white including flush pipe and waste pipe complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe)with grating union discharge pipe etc complete all as specified .

S&F 75 mm dia PVC (SWR) floor trap plain with grating incl jointing with solvent cement

M&L for 20mm thick granite stone slab machine cut, bedded over 15mm thick (1:4) cement mortar scree and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete as directed

M&L for Non skid ceramic coloured tiles 7 to 8mm thick (Square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18sqm in floor, over 15mm thick screed bed in CM 1:6 on floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade as specified and as directed.

M&L for glazed ceramic coloured tiles in vertical surfaces of size 350X450X7 mm thick set and jointed in neat cement slurry and pointed in coloured cement as in vertical surfaces such as dado/skirting and facea of side bldg over & including 10mm thick rendering in CM(1:4) complete all as specified and as directed.

M&L 75 mm thick PCC 1:3:6 type C2 using 40mm graded stone aggregate laid in panels surface finish even and smooth without using extra cement as in plinth protection complete all as specified and as directed.

M&L forming 12mm thick expansion joint filled with preformed bituminous filler and top 30mm primed and sealed with sealing compound grade 'B' for 100mm thick slab

S &F brass chromium plated Tubular towel rail, 20mm dia, D type, 60cm long between flanges all as specified and directed.

Supply and laying and concealed for 16mm CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings (Brass elbow, Brass Tee, Male threaded brass adaptor, Female threaded brass adaptor etc) on walls/ceiling or laying in floors complete all as specified and directed

S & F 20mm bore GI tubing medium grade with all fillings and fixtures fixed to wall ceiling or laid in floors etc complete

S&F 25mm bore galvanised steel tubes,medium grade for flush pipes, water supply pipes etc, fixed to walls and ceilings or laid in floors.

M & L for Drilling and tapping cast iron water mains (Position) for branch connections of the internal dia of 25mm bore GI pipe

M&L Water proofing treatment on RCC roof etc. comprising with the following operation & as specified herein below:- (a) M&L for10 mm thick rendering on fair faces of brick works / Concrete surfaces finished even and smooth without using extra cement in cement mortar 1: 3complete all as specified and as directed. (b) M&L for priming evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 Kg per sq.m including cleaning the surface. (c) M&L App based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforment with polyster non woven fabric (wt reinforcement not less than 150 gms/sqm) laid on primed surfaced application complete all as apecified and directed (Primer should be measured and paid as per Item above). (d) M&L applaying two coat of Aluminium paint over APP Membrane complete all as apecified and directed.

S&F 75 mm bore PVC (SWR) pipes of single socketed in any length with rubber ring joints laid in trenches or in floors all as specified

S&F 110mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall

S&F 75 mm bore. PVC (SWR) bends

S&F 110mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches

S&F 110mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall

S&F 110 mm PVC (SWR) bend any radius

S&F 110mm bore.PVC(SWR) junction single (single T) equal or unequal with access door

M&L for 40mm thick cement concrete 1:2:4 type B0 (12.5mm graded stone aggregate) as in Damp proof course to horizontal or vertical surfaces including necessary formwork

M&L for Applying evenly a coat of blown type bitumen 85/25 at the rate of 1.50 kg per square metre and blinding with clean dry sand @ 0.05 cu. m. per sq. m

M&L for Polythene film, 50 micron thick, laid on a coat of bitumen primer, @ 0.30 to 0.50 kg per sq. m

Returning filling including spreading, levelling, watering and well ramming in layers n exc. 25cm

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in Hard/ Dense soil

M&L for Rolling and consolidating formation surfaces in cutting rolling with power roller of 8 to 12 tonne.

M&L for 75mm thick PCC type D2(1:4:8) using 40mm graded crushed aggregate as in sub base, finished even and fair complete.

M&L for PCC type B0 (1:2:4) using 12.5 mm graded crushed aggregate in coping ,mass concrete.

Removing excavated material n, exe 50m and depositing where directedat a level n, exe 1.5 m above the starting point complete all as spfd

M & L for Providing and laying 60mm thick factory made chamfered edge cement concrete Paver block of M-35 grade with approved colour, design and pattern as in footpath, parks, lowns, drive ways or light trafic parking etc of required strength, thickness and size/shape, made by table vibratory method using PU mould, laid in required colour and pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/laying of interlocking paver blocks including the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand

M & L for PCC 1:3:6 type C-2 (using 40 mm graded stone aggregates) as in foundation of manholes, mass concrete etc. complete all as specified and directed.

M&L for Brick work with sub class old size 'B' brick stright or curved on plan exc 6m mean radius built in cement mortar (1:4)

M & L for rendering 15mm thick in cement mortar 1:3 on fair faces of brick or concrete surfaces and including mixing water proofing compound as per manufactureres instructions complete all as specified and directed. Note :- Water proofing compound shall be measured and paid for seperately under appropriate item of Sch "A' as supply only. complete all as specified and directed.

M&L for PCC 1:2:4 type B1 (using 20mm graded aggregate) as in benching of surface channels/manholes including fair finishes of surfaces chamfering, throating and weathering and necessary form work complete as specified and directed.

Extra for forming fair finished channel or drain up to 30 cm inner girth in cement concrete using extra cement including forms, moulds mitered/stopped ends etc. all as specified and directed.

Supply only RCC manhole cover (900mm X 450mm X 50mm) all as specified and directed by E-in-Charge

Supplying, fixing, jointing and testing reinforced concrete drain pipes 150 mm bore, class NP2, laid and jointed with collar in C M 1:1 complete all as specified and directed.

M & L for concrete bed to drain pipes in PCC 1:3:6 type D-2 (using 40 mm graded stone aggregates) including packing under and hauching against the side of the pipes after they are laid tested for pipes of 150 mm bore dia complete all as specified and directed.

Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrte 1:2:4 type B-1 smooth finished, and reforming benching as required for internal dia of pipe 150mm.

M & L for On site LLDPE conventional septic tank 25 Users size (3.5 x1.5x 1.5mtr)designed to carry sewage and sullage water, excavation in any type of soil, below foundation in 150mm thick Hard core, 150mm thick PCC 1:3:6, Vent shaft, connection etc., complete with effective depth of 1.5 m and overall depth of 3m including returning and filling and all as specified and directed by E-in-Charge.

M & L for On site LLDPE conventional septic tank 10 Users size (2.8 x1.2x 1.3mtr) designed to carry sewage and sullage water, excavation in any type of soil, below foundation in 150mm thick Hard core, 150mm thick PCC 1:3:6, Vent shaft, connection etc., complete with effective depth of 1.5 m and overall depth of 3m including returning and filling and all as specified and directed by E-in-Charge.

M & L for construction of septic tank 100 users designed to carry sewage and sullage water, excavation in any type of soil, below foundation in 150mm thick Hard core, 150mm thick PCC 1:3:6 and PCC 1:2:4 , slope 1:10, length of tank size 5800mm x 1800mm x 1300mm, thickness of walls and slab follow ref TD Drgs, RCC base slab, baffle walls and roof slab including beams etc with vent shaft, manhole openings with cover connection etc complete all as specified and directed by E-in-Charge. Ref TD Drg No CEAA/TD/79 Sheet 1/1 to 1/3

Soakage wells excavation in any type of soil, fdn in 150mm thick PCC in 1:3:6, walls of honey combed masonry with top ring of M25 concrete including intersepting chamber and screen chamber made of brick masonry in CM 1:4, RCC cover slab (Reinforcement 10mm dia) in M25 SFRC cover, inter connecting pipes of RCC/DWC complete filled with brick bats of size 1.2m dia and 3.0m effective depth complete all as specified and directed by E-in-Charge. Ref TD Drg No CEAA/TD/80 Sheet 1/1 to 1/2

Soakage wells excavation in any type of soil, fdn in 150mm thick PCC in 1:3:6, walls of honey combed masonry with top ring of M25 concrete including intersepting chamber and screen chamber made of brick masonry in CM 1:4, RCC cover slab (Reinforcement 10mm dia) in M25 SFRC cover, inter connecting pipes of RCC/DWC complete filled with brick bats of size 2.4m dia and 3.0m effective depth complete all as specified and directed by E-in-Charge. Ref TD Drg No CEAA/TD/80 Sheet 1/1 to 1/2

Soakage wells excavation in any type of soil, fdn in 150mm thick PCC in 1:3:6, walls of honey combed masonry with top ring of M25 concrete including intersepting chamber and screen chamber made of brick masonry in CM 1:4, RCC cover slab (Reinforcement 10mm dia) in M25 SFRC cover, inter connecting pipes of RCC/DWC complete filled with brick bats of size 1.8m dia and 3.0m effective depth complete all as specified and directed by E-in-Charge. Ref TD Drg No CEAA/TD/80 Sheet 1/1 to 1/2

M & L for brickwork with subclass 'B' bricks straight or curved on plan exc 6 m mean radius in CM (1:6) all as specified.

M & L for rendering 10mm thick in cement mortar 1:4 on fair faces of brick walls or concrete surfaces complete all as directed.

M&L for cement concrete (1:3:6) type C2 using 40 mm graded crushed stone aggregate as in surface channels and drains and benching including finishing the top of benching even and smooth using extra cement.

M&L for precast cement concrete Type B1, 1:2:4 (20mm graded aggregate) in lindings, cover slabs (for manholes etc), chullah hoods, chhajja, water troughs, shelves and similar articles with plain faces, setting in CM 1:4, complete all as specified and as directed

M & L for Point wiring with 1.5 sqmm copper conductor cables (multistranded), FRLS PVC insulated, insulated single core 1100 volts grade & with one run of 1.5 Sqmm single core copper stranded FRLS PVC insulated 1100 volts grade wire for continuous earthing complete in and including PVC casing and caping unsheathed (using colour code as per IS), 1100 Volts grade in and including 3 mm thick plastic laminated sheet top cover for one light /fan/exhaust fan point controlled by one, one way 5 Amp switch with and including continuous 1.5 sqmm copper conductor (multistranded using colour code) FRLS PVC insulated and unsheathed cable as earth wire connected to earth dolly complete all as specified and directed.

One light point controlled by one switch.

One Exhaust/Wall mounted /Ceiling point controlled by one regulator/switch

One 3 pin socket 5 A on same board.

Material and labour for providing point wiring with two runs of 2.5 Sqmm multi stranded copper conductor FRLS PVC insulated 1100 volts grade wire for continuous earthing complete in and including PVC casing and caping unsheathed (using colour code as per IS), 1100 Volts grade in and including 3 mm thick plastic laminated sheet top cover for housing one 15 A Switch / sockets with and including continuous 2.5 sqmm copper conductor (multistranded using colour code) FRLS PVC insulated and unsheathed cable as earth wire connected to earth dolly complete all as specified and directed.

Material and labour for providing point wiring with two runs of 4 Sqmm multi stranded copper conductor FRLS PVC insulated 1100 volts grade wire for continuous earthing complete in and including PVC casing and caping unsheathed (using colour code as per IS), 1100 Volts grade in and including 3 mm thick plastic laminated sheet top cover for housing one 15 A Switch / sockets/ Industrial socket with and including continuous 4 sqmm copper conductor (multistranded using colour code) FRLS PVC insulated and unsheathed cable as earth wire connected to earth dolly complete all as specified and directed.

S&F sheet metal enclosure with socket plug top , single pole and neutral enclosure with two pin earth plug and socket complete with one MCB SP of capacity 20 Amps.including fixing concealed in wall and making good the disturbed surface complete all as directed

S & F Sub Main Wiring with FRLS PVC Insulated multistranded copper conductor wires of size 2x6.0 sq. mm + 1x6.0 sq. mm earth wire in casing caping complete as directed. Note : for Item No 5 One run of phase wire one run of Neutral wire and one run of Earth wire and one run of casing and capping shall be meassured and as one length.

Supply and fix sheet metal enclosure MCB DB double door SPN 8 way 230 V with neutral link and with 200 A bus bar including fixing concealed in wall including cutting chasing in stone masonary / Brick masonary and making good the disturbed surface making all nacessary incomming and out going connections using proper size copper thimbles complete all as required on site all as directed

Ditto all as per Ser Item No 107.00 above but MCB DB double door SPN 12 way 230 V with neutral link and with 200 A bus bar

S&F MCB SPN 40 to 63 Amp 10 kA 240 Volt, 'C' Curve and electric connections with copper thimbles complete all as specified and directed by Engr-in-Charge.

M&L for switch piano flush button single pole one way 5/6 amps 240 volts

S & F Switch piano flush button single pole one way 15/16 amps 240 Volts.

M&L for socket 5 amps 5 pin flush type, 230 volts.

M&L for socket out let, 6 pin 5 and 15 amps multi purpose 2 in 1 flush type, 230 volts

M&L for ceiling rose surface bakelite 3 terminals

S&F MCB SP 240 volt 6 to 32 A 'C' series complete

S&F MCB SPN 240 volt 6 to 32 A 'C' series complete

Supply and fixing LED light fitting with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete

Supply and fix high quality indoor Surface and wall mounted LED batten 22 Watt, provided for efficient heat dissipation with polycarbonate diffuser & integrated electronic driver complete with all accessories internally pre-wired and including connecting up with three core 0.5 Sqmm flexible copper conductor cable ceiling rose to fitting terminal.

Supply and fix exhaust fan, Heavy duty with steel body AC single Phase. 230V of size 300 mm sweep 900 RPM with blades, frame, louvers made out of aluminium shhet of 0.5 mm thick with frame, anchor fastners for mounting fan, 1.5 Sqmm 3 Core cable from Ceiling rose to fan complete all as specified and directed.

Supply and fix electric water heater, storage type steel body with copper inner tank and heating element 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece, 4 Nos fasteners etc incl suitable hot and cold water pipe

Taking down the existing street light fitting and Supply & fix (in Repalcement) energy saving and environmental friendly long life LED Street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with impact and corrosion resistant including thermal management in multiple optics IP 65/IP66 road way luminaries with LEDs as light source and lens embedded PC cover /toughened glass and impact resistance of IK07 and electronic driver fixed on pole/wall with and including suitable dia size bracket as per manufacturer recommendation, bracket complete with MS flat iron clamps (clamp shall be 40x5 mm MS flat), nuts and bolts and washers painting the clamps with coat of aluminium paint over a coat of red oxide primer including connection complete all as specified.

M&L for providing earthing complete with galvanised iron earth plate electrode 600 mm x 600 mm x 6mm as earthing lead buried directly in ground vertically to a depth not less than 2.25 Mtr deep below ground level with top edge of the plate not less than 1.5 Mtr below normal ground level connected to and including galvanised wire 4 mm as earthing lead by means of bolts, nuts, check nuts & washers etc made of GI and connected to earthing test point, providing charcoal and common salt all as shown in electrical plate No. 5 of SSR Part I of 2009 & as specified or indicated and testing on completion including exaction/earth work in any type of strata PCC (1:3:6) type C1 earthing chamber, pre cast slab 50 mm thick in cement concrete (1:2:4) type B1 (reinforced with welded steel wire fabric (XPM) weight not less than 4 Kg/sqm), funnel with wire mesh, watering pipe of 20 mm bore medium grade and lugs, including galvanised iron wire 4 mm with GI protection pipe of 15 mm medium grade 7.5 meter long, etc complete all as specified.

Material and labour for providing point wiring with two runs of 4 Sqmm multi stranded copper conductor FRLS PVC insulated 1100 volts grade wire for continuous earthing complete in and including PVC casing and caping unsheathed (using colour code as per IS), 1100 Volts grade in and including 3 mm thick plastic laminated sheet top cover for housing one 15 A Switch / sockets/ Industrial socket with and including continuous 4 sqmm copper conductor (multistranded using colour code) FRLS PVC insulated and unsheathed cable as earth wire connected to earth dolly complete all as specified and directed.

Supplying & Laying GI pipe medium grade in trenches indluding all fittings as directed of following sizes:-

25 mm bore

40 mm bore

Excavating in trenches n.exc 1.5 Mtr wide and n.exc 1.5Mtr deep for pipe line in soft/loose type of soil getting out and levelling of bottom surface to required level complete.

Soft/loose soil

Hard/dense soil

Soft/disintegrated rock

Supply and fix gun metal gate valves with iron wheel head, screwed both ends for iron pipe ISI marked as per IS 778 of following sizes

25 mm bore

40 mm bore

Construction of valve pit chamber of sizes 600 x 600 x 750 mm with brick massonary, one brick thick wall in cement mortor (1:4) on 100mm thick PCC 1:4:8 type D2 (using 40mm graded aggregate) as in foundation complete including neccessary exc and earthwork in any type of soil, formwork, 15 mm thick cement & plaster rendering internally all arround over brick wk & externally upto 15cm below normal GL with 10 SWG thick MS sheet cover incld 40 x 40 x 6mm MS angle frame fixed locking arrangement and painting with one coat of red oxide and two coats of black Bituminous paints all as specified and directed by Engr-In-Charge

M&L for cutting of existing GI pipe dia up to 40 mm in position for insertion of new GI tee for branch connection complete with all fittings.

Supplying, Laying, jointing, testing and commissioning of LT under ground cable 1100 volts grade XLPE (cross linked polythene ) armoured with galvanised round steel wire or steel strip , electric power cable heavy duty, with multi stranded aluminium conductor, laid in trenches, ducts fix on walls/poles with proper size saddles and clamp laid under roads/path/ drain /colverts or enclosed in GI pipe/ fix complete including Taking out of old unserviceable UG cable and all as specified for following size:-

16 sqmm 2 core

10 sqmm 2 core

Material and labour for stone dust sand cushioning to under ground cable, provided with a layer 8 cm before and 15 cm after laying and stretching jointing and testing the cable all as specified and directed. [Note : Measuremenet will be done after punning]

Supplying and laying un-reinforced precast concrete cable cover, class I, flat, size 250mm x 150mm x 40mm for cable protection

Supply and fix GI Pipe Light grade with all connected accessories of sizes 50 mm dia complete all as specified and directed by Engr-in-Charge.

M/s Kirti Enterprises (BID ID -3374535)

D R CONSTRUCTION (BID ID -3375646)

Shri Sant Cosntruction (BID ID -3382589)

tulsani associates (BID ID -3383601)

om construction (BID ID -3370143)

KSP ENTERPRISES (BID ID -3373033)