SPECIAL REPAIR TO FLOORING AND PANELLING OF BLDG NO KG-57 AT KELVIN GROVE UNDER GE (I) JUTOGH

Amount

Demolition of cement concrte (un-reinforced) in ground floor and paving n.exc 15 cm thick bleow or above hround level, complete all as specified and directed.

Demolition of brick work or stone boulder masonry built in cement mortar, complete all as specified and directed.

Dismantling of RCC shelf other than ground floors and similar suspended works complete all as specified and directed.

Taking down cement plaster of any description on brick wall surfaces etc including raking out joints hacking for key, scrubbing down down with water etc., complete all as specified and directed.

Dismantling floor, hearth or wall tiling incl cement mortar bedding (but not backing) and rubbish off the premises, complete all as specified and directed.

M&L for brick work with sub class 'B' bricks of class designation 10 all as per IS-1077-1992 (minimum compressive strength of brick 100 kg/Sqcm) old size bricks, straight or curved on plan exceeding 6 mtr mean radius built in CM 1:6, complete all as specified and directed.

M&L for stone masonry random rubble, well bonded, bedded and solidly hearted in CM 1:6 in retaining walls abutments brought upto coarses including necessary provn of weep holes etc., complete all as specified and directed.

M&L for brick work with sub class 'B' bricks, straight or curved on plan to any radius in half brick thick built in CM 1:4 with sub class 'B' bricks of class designation 10 (minimum compressive strength of brick 100 kg/ Sqcm), complete all as specified and directed.

M&L for rendering 10mm thick in two layer on bricks/ stone masonry surfaces or surfaces other than fair face of brick work in CM 1:6, finishing surfaces even and smooth without using extra cement, complete all as specified and directed.

M&L for rendering 15mm thick CM 1:4 on fair face of brick, hollow block, concrete surface finished even and fair witout using extra cement, complete all as specified and directed. Note: WPC shall be measured and paid separately.

M&L for 5mm thick rendering in CM 1:3 on concrete surface of chajjas or ceiling, finished surfaces complete all as specified and directed.

M&L for Nonskid ceramic tiles (coloured) 300x300x 7 to 8mm thick (square/ rectangular) area of each tile exc. 0.06 sqm but n. exc. 0.11 sqm as in floors set and jointed in cement slurry and pointed in coloured cement including provision of screed bed 15mm thick in CM 1:6, complete all as specified and directed.

M&L for 1st quality, glazed ceramic coloured tiles 350x250x 7mm/ 450x350x 7mm thick on verticle surface of walls with neat cement slurry @ 3.00 Kg/Sqm incl pointed in white cement with pigment to match the shade of tiles, over and incl scrceed bed 10mm thick 1:4, complete all as specified and directed.

M&L for RCC 1:2:4, type B-1, using 20mm graded crushed stone aggregate as in shelves/ slabs/ beam/ columns/ foundation and like with and incl use and waste of necessary form work complete all as specified and directed.

M&L for mild steel TMT Bars 10mm dia and over cut to length, bend to shape required, incl cranking, bending, for hooping for columns, hooking ends and binding with and incl MS wire (Annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for mild steel TMT Bars 8 mm dia cut to length, bend to shape required, incl cranking, bending, for hooping for columns, hooking ends and binding with and incl MS wire (Annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for PCC 1:2:4, type B-1, using 20mm graded crushed stone aggregate as in copings, bed plates, fixing of hold fasts and other similar works and the like incl weathering, slightly rounded or chamfered angles and throating as directed incl use and waste of necessary form work complete all as specified and directed.

Taking down chawkhat or frame with (without taking of shutters from the frames) exc 1.50 sqm but n. exc 4sqm complete all as specified and directed.

All as per Srl item No 18.00 above but for n.exc 1.5 sqm, complete all as specified and directed.

S&F Aluminium anodised powder coated sliding type three track window with shutter and frame including aluminium grill and mosquito proofing net and 5 mm thick tinted glass, size of frame 93.00 x 31.75 x 1.3 mm thick for top and sides, 93.00 x 31.75 x 1.3 mm thick, bottom and shutter frame 38 x 18 x 1.5 mm thick., aluminium grill 6 mm dia design No DG-102 make DEDO grill or design No A-103 make aluminium grill fixed to 50x20x1.5mm thick including necessary handles, tower bolts, stopper etc., complete all as specified and directed.

S&F powder coated aluminium sec (frame/ shutter/ partion) for doors, windows, ventilators, partition of powder coating minimum thickness of powder coating 50 micron with one or more rebates including joining cleat for fixing etc., complete all as specified and directed.

S&F aluminum section powder coated (powder coating color/ shade as approved by GE) of colour as approved door with frame and shutters partially gauze and PVC composite board 5mm thick fixed with aluminium clip section door section of aluminium door shutter as under complete all as specified and directed. (I) Frame 100x40x2mm (ii) shutter style 85x44.45x3mm thick section (iii) Top rail 95.25 x44.45x1.7mm thick (iv) middle rail 83.50x44.75x1.7mm thick (v) Bottom rail 114.30X44.15X1.7 thick section (vi) Glazing clip 0.7mm thick (vii) 2 Nos Handle Powder coated Aluminium 200mm long as approved (viii) Tower bolt 9.90mm dia and 200mm long (ix) Mortice lock 100MM 7 LEVER make Godrej or equivalent as approved (x) Hold fast aluminium 100mm long (xi) 1No hydraulic door closer each shutters (xii) Reinforced with 2 Nos 10mm dia MS bar with bolt complete on top and bottom rail of door.

S&F in repairs factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ ceosetory windows & other Frames/ Chowkhat of size 45 x 85 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction o and making it good to match with existing surface, complete all as specified and directed. Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

S&F providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moistureproof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, complete all as specified and directed. Note: stainless steel butt hinges and necessary S.S screws shall be paid separately.

S&F sheet glass 5.5 mm thick tinted glass in square exc 0.5 sqm in each pain complete all as specified and directed.

S&F sheet glass 4.00 mm thick figured glass pin headed type and glazing with oil putty or wooded bead built in squares not exceeding 0.5 sqm in each pane, complete all as specified and directed.

Dismantling plain or corrugated steel sheeting, with ridge, gutters, etc, any gauge, and thickness incl Nainital pattern roof covering, fixed with J/L hooks or coach screws complete all as specified and directed.

S&F for pre-painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.60mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, ridges, flashing, eaves board, valley gutter etc, fixed all as per manufactures's instructions, fixed with self tapping screws as directed at site with suitable arangement as required, complete all as specified and directed.

S&F for pre-painted galvatume aluminum zinc coating GI based plain steel sheet 0.60mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, facia, ridges, flashing, eaves board, valley gutter etc, fixed all as per manufactures's instructions, fixed with self tapping screws as directed at site with suitable arangement as required, complete all as specified and directed.

S&F 0.50mm thick of an having tensile strength of 550 Mpa ,as in roof/wall/ceiling & colour coated aluminium zinc coating GI based liner pofile sheet with high quality steel fixed with self tapping screw complete all as specified and directed.

Dismantling of boarding of any description and in any position complete all as specified and directed.

S&F GI Clip-in false ceiling tiles of with beveled edges of with GI sheet (600mmx600mm) is manufactured out of 0.50mm galvanized steel of 100 gsm/sqmtr sheet having powder coated with 60 microns polyester paint on front side. These tiles shall have beveled edges. Two sides of eacch tiles are raised and piped and stopped to ensure positive engagement into the spring clip-in profile,yet allow for demounting of individual tiles. The rigid suspension system consists of rows of 0.5mm galvanized steel clip-in profiles of size 24mmx34mm of 0.5mm thick and installed at 600mm c/c spacing to support the tiles,clip-in profiles are suspended with hold on clamps. Suspension angles or 4mm G.I Wire are suspended from the roof structure. The tiles are held in place by pressure clips. In the flexible system the hanger and suspension clip replace the suspension angle. GI Edge profile are of size 24x24x0.35mm thick with matching the color with tiles, complete all as specified and directed.

Dismantling timber scantlings in any position in fillets, rails, posts, rafters, purlins, etc. under 40 sq. cm in section (Unframed work) complete all as specified and directed.

S&F for plain fillets, square, rectangular or triangular in section, and secured with nails or brads, using IInd class hard-wood clean sawn in sectional area exc 13 sqcm and not exc 25 sqcm complete all as specified and directed.

M&L of standard size (100mmx12mm), wood panelling refers to wall/ ceiling covering made made from pine wodd planks, featuring a light,natural colour with visible grain patterns and knots fixed with self tapping screw on wood frmae work etc. complete all as specified and directed.

S&F 30mm thick IInd class hardwood wooden planks,width n.exc 20cm etc, complete all as specified and directed.

S&F in repair 4.5mm thick 100% PVC synthetic mat with standard line marking and incl all necessary materils required for proper surface finished, shade approved by GE,etc complete all as specified and directed. Note:- (i) Minimum weight of as per above thickness i.e. 65kg/roll. (ii) The mats hould have been approved by BWF as grade/level & warranty for 5 yrs from the date of actual completion. (iii) The courts mats must be within permissible limits set by BWF for standards releted to friction,shock absorption and slip resistance. (iv) The mats should be installed in copmlete aspect and as per the direction of the auth.

S&F in repair 10mm thick PVC synthetic mat flooring, durable, waterproof and easy to maintain also providing providing in this flooring excellent shock absorption, anti slip resistance and insulation making it ideal for gyms and incl all necessary materils required for proper surface fixed, shade approved by GE, etc complete all as specified and directed.

M&L for 75mm thick PCC 1:3:6, type C-2, using 40mm graded crushed stone aggregate, laid in 1:20 slope as in plinth protection, coping, surface finished even and incl use and waste of necessary form work, complete all as specified and directed.

S&F Mild steel butt hinges medium weight, clod rolled, 100mm, ISI marked, complete all as specified and directed.

S&F barrel tower bolts aluminium anodised exlruded section of size 200 mm complete all as specified and directed.

S&F 250 mm long aluminium anodised sliding door bolt with hasp, staple (bolt type) and fixing cleap of sheet, cast or extruded sections, bolt not less then 12mm dia with and including a minimum of 6 bolt and nuts, fixed on plate or staple plate complete all as specified and directed.

S&F aluminium fabricated type extruded handles of size 150 mm complete all as specified and directed.

S&F aluminium fabricated type extruded handles of size 125 mm complete all as specified and directed.

S&F in repair 25 mm dia stainless steel chromium plated curtain rails fixed with brackets, stops, rollers, etc. complete all as specified and directed.

Taking up or down 15 mm dia steel tubing incl connection and removal from site, complete all as specified and directed.

All as per srl item No 46.00 above but for 20mm dia, complete all as specified and directed.

S&F GI tubing medium grade with all fittings fixed to walls or laid in floors 15mm bore (concealed & open) complete all as specified and directed.

S&F GI tubing medium grade with all fittings fixed to walls or laid in floors 20mm bore (concealed & open) complete all as specified and directed.

S&F in repair 15mm bib tap cast copper alloy chromium plated with crutch or butterfly handle screwed down screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed.

S&F in repair stop valve/ Angle cock/ concealed fancy type cast copper alloy 15mm bore screwed down high pressure chromium plated concealed type complete all as specified and directed.

S&F in repair 15mm bore CP fancy type (L-Type bend wall mixer, sink mixer & WBH mixer for mixing hot & cold water cast copper alloy with capstan handle, screwed down for iron pipe and fixed on wall, WHB complete all as specified and directed.

S&F in repair vitreous china wash basin pedastal pattern super white/ colour of size 560x475mm including all fittings, decorative type complete, fixed complete all as specified and directed.

S&F in repair vitreous china urinal, half stall type, of size 600x355x 265mm, white (excluding flushing cistern, flush pipe), but including waste pipe fixed, complete all as specified and directed.

S&F in repair stop valve cast copper alloy 20mm bore screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unioin fixed complete all as specified and directed.

S&F in repair PVC connections 15mm size with PTMT nuts of length 450mm, complete all as specified and directed.

Dismantling water tanks exc 500 n. exc 1000 ltr capacity complete all as specified and directed.

S&F 1000 ltr capacity rotational moulded polythene water storage tanks (clyndrical vertical with closed top) hoisted and fixed in position all as spd in SSR Part I, complete all as specified and directed.

S&F 20mm bore dia ball brass valves, high pressure with polythene float and flynut complete screwed for iron pipes etc, complete all as specified and directed.

S&F in repair vitreous China wash down water closet (Pedestal pattern) coloured including all fittings, fixing bolts, waste pipe, inbuilt fluhsing cistern and flush pipe complete all as specified and directed.

M&L for PCC 1:3:6, type C-2, using 40mm graded crushed stone aggregate as in surface channel/ drains, incl fair finished & necessary form work complete all as specified and directed.

Dismantling of 100mm cast iron or reinforced concrete drain pipe, jointed in cement mortar and taking out of trenches/ floor/ wall if required, complete all as specified and directed.

S&F 110mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall including clamps as required complete all as specified and directed.

S&F 110mm dia PVC (SWR) bends with oval access/ plain door with rubber ring joints fixed as required complete all as specified and directed.

S&F 110mm dia PVC (SWR) junction double, (double/ single T), equal or un equal with oval access door including jointing with solvant cement as required, complete all as specified and directed.

S&F 110mm dia PVC (SWR) "P" /'S' trap single, equal or un equal of any length including jointing with solvant cement as required complete all as specified and directed.

S&F 75 mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall including clamps as required complete all as specified and directed.

S&F 75mm dia PVC (SWR) junction double, (double/ single,T), equal or un equal with oval access door including jointing with solvant cement as required, complete all as specified and directed.

S&F 75mm dia PVC (SWR) bends with oval access/plain door with rubber ring joints fixed as required complete all as specified and directed.

S&F 75mm dia PVC (SWR) floor trap, plain with SS grating including jointing with solvant cement incl necessary PCC & form work as required complete all as specified and directed.

M&L for preparation of new steel surfaces including preparation of surfaces and applying two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified and directed.

M&L for preparation of old painted steel surfaces including preparation of surfaces and applying one coat of synthetic enamel paint, complete all as specified and directed.

M&L for preparation of newly plastered or unplastered or previously untreated surfaces of walls and applying two coats of exterior emulsion paint & over one coat of primer complete all as specified and directed.

M&L for two coats of distemper oil emulsion on wall incl preparation of new surfaces over one coat of primer on wall surface incl 2mm thick wallcare putty, complete all as specified and directed.

M&L for preparation of newly decorated plastered/ unplastered surfaces of ceiling and applying one coat of white wash on ceiling and AC plain building board surfaces as in ceiling, complete all as specified and directed.

Dismantling stone slabs and tiles of any description or thickness in floors, aprons etc laid, bedded and pointed in any mortar, complete all as specified and directed.

M&L for Green/ Black marble flooring /woor/windows cills,or on cooking platform 18 to 20mm thick laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing over and including 15mm thick cement screed bed in CM(1:6), ( size of the slabs shalll not be less than 100cmx60cm), complete all as specified and directed. Note:- (i) The rate of granite stone shall be deemed to incl for full rounded off corner/ edges incl holes for pipe all cutting to make it square or rectangular. (ii) The rate shall also be deemed to incl for cutting and polishing machine and granite polishing to achive the desired granite finish.

Supply only water proofing compouond all as specified as per manafature instruction, complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided complete all as specified and directed.

S&F roof trusses (framed) trussed, purlins, posts, crane gantries, rails and fastening and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces cleats Fe 410-W(Gde-E- 250), quality-A etc., complete all as specified and directed.

S&F Framed work such as grills, gratings, etc.,with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladder; framed baluster; walk ways; railing; framework of watertanks staging and similar work conforming to Fe-290. Gde-E-165, complete all as specified and directed.

Dismantling timber scantlings ,framed/unframed work of size 40 sqcm and over in section ,in any position in any position with nails etc., complete all as specified and directed.

M&L for 2nd class HW clean Sawn timber scantling/ posts complete all as specified and directed.

M&L for PCC 1:4:8, type D-2, using 40mm graded crushed stone aggregate, as in filling of mass concrete for floors complete all as specified and directed.

M&L for 40mm thick PCC 1:2:4, type B-1, using 20mm graded crushed stone aggregate as base coarse for floors, complete all as specified and directed.

S&F in repair sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated brackets, bracket guard and railing 60cm long incl screws, complete all as specified and directed.

S&F in repair soap dish chromium plated of size 180x160x90mm any type, fixed to plugs with chromium plated brass screws, complete all as specified and directed.

S&F in repair brass chromium plated tubular towel rail 20mm dia 'D' type 60 cm long between flanges complete all as specified and directed.

S&F fibre reinforced translucent plain sheeting, 5 mm thick with two corrugation side lap fixed with coach screws and washers, in roofs, wall etc., complete all as specified and directed.

S&F plain galvanised, mild steel sheeting 1 mm thick with grade of zinc coating 120 gsm as in ridges, faciya, hips, valley gutters, drip and straight flashings, fixed with L or J type hooks or self thread making steel screws of length not less than 75mm with suitable arrangement as required, complete all as specified and directed.

M&L for non skid ceramic tiles 7-8mm thick coloured (Square/ rectangular) joint free area of each tiles exceeding 0.18 sqm but n exc 0.38 sqm in floors set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed as in CM 1:6, complete all as specified and directed.

Taking down carefully copper/ aluminum point wiring (light, fan socket or power) complete incl. (fitting such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc.), removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors etc., complete all as specified and directed.

M&L for point wiring 1.5 Sqmm (nominal cross sectional area) with colour coding multistranded copper conductor cable, PVC insulated (FRLS-H) and unsheathed cable and including drawn through PVC conduit 25mm size with all fittings and accessories, terminated to PVC board of suitable size for housing/ mounting the switches/sockets including 1.5 Sqmm PVC insulated unsheathed multistranded copper conductor cable earth wire connected to common earth dolly for one light point control by one, one way switch complete all as specified and as directed.

All as per Srl Item No 94.00 above but for one 3 pin socket outlet 5 amps, on independent board, complete all as specified and directed.

All as per Srl Item No 94.00 above but for one 3 pin socket outlet 5 amps, on same board with other switches, complete all as specified and directed.

All as per Srl Item No 94.00 above but for one 3 pin 15 Amps power point on independent board with 4.0 Sqmm size FRLS-H PVC insulated unsheathed multistranded copper conductor cable and with 4.0 Sqmm FRLS-H, PVC insulated unsheathed multistranded copper conductor as earth wire, complete all as specified and directed.

S&F switch piano flush single pole, one way 5 Amp (ISI marked) complete all as specified and directed.

S&F switch piano flush single pole, one way 15 Amp ( ISI marked) complete all as specified and directed.

S&F socket (ISI Marked) 2 in 1, 3 pin 5/6 amps flush type, complete all as specified and directed.

S&F socket 2 in 1, 5 pin 5 and 15 amps (ISI marked) flush type universal, complete all as specified and directed.

S&F ceiling rose, 3 phase, PVC polycarbonate, insulated body (ISI Marked), complete all as specified and directed.

S&F LED inverter batten tube light along with fixture, 1x 20 watt, (4 Feet) wall mounted LED batten, with diffuser, complete including electrical connection with copper cable from ceiling rose to fittings and including taking down existing fittings and all fixing arrangements complete all as specified and directed.

S&F in replacement 36W LED(4 x 1) surface / Recess mounting luminaire suitable for hanging on any surface including connecting twin core cable up to nearest point complete with separate electronic driver & high brightness LEDs white colour complete all as specified and directed.

S&F in replacement 36/40W LED (Size 2'x2') square shaped Recess mounting type luminaire having white polycarbonate body & Alumium heat shink with PMMA diffuser, 5700K including connecting three core copper cable up to ceiling rose complete with separate electronic driver & high brightness LEDs white colour complete all as specified and directed.

M&L for lamp holder (Angle) PVC /Polycarbonate type with back plate suitable for batten fittings, complete all as specified and directed.

M&L for LED 15 Watt lamp, complete all as specified and directed.

S&F LED flood /focus light in die cast powder coated aluminium body & IP 66 protection 180 watt, 220 V, 120 Lm/Watt AC including connecting up with three core flexible copper conductor cable of suitable size complete and including taking down old unsv existing fittings complete all as specified and directed.

S&F LED inverter building security light 25 watt fixed on wall suitable bracket with all connected accessories complete including electrical connection with copper cable from ceiling rose to fittings and including taking down existing fittings and all fixing arrangements complete all as specified and directed.

S&F LED tube light along with fixture, 1x 10 watt, (2 Feet) wall mounted LED batten, extruded PVC, heat sink provided for efficient heat dissipation & integrated electronic driver, optics diffused, complete including electrical connection with copper cable from ceiling rose to fittings and including taking down existing fittings and all fixing arrangements complete all as specified and directed.

S&F LED inverter light fitting 20W bulk head luminaire including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size including taking down old unsv existing fittings complete all as specified and directed.

S&F 10 Sqmm flat twin core, 1100 Volts grade, stranded, heavy duty, cable PVC insulated aluminium conductor, weather proof and incl fixing all arrangements, complete all as specified and directed.

S&F exhaust fan made of study engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, copper winding of sweep 300MM incl fixing all arrangements cutting of existing wall/ roof, etc., complete all as specified and directed.

S&F exhaust fan, AC single Phase 230/ 240V of size 300mm sweep metal body with louvers incl fixing all arrangements cutting of existing wall/ roof, etc., complete all as specified and directed.

S&F electric water heater, storage type steel body with SS inner tank and heating element upto 2 KW capacity 25 Liter, BEE 5 Star rated, complete with all accessories such as safety valve, thermostat, NRV, connection pipe (Hot/ Cold) etc. and fixing arrangements, complete all as specified and directed.

S&F in repair surge protection device (SPD) voltage protection level Up upto 1.3kV, suitable for protection of all terminal equipments both common & differential mode protection complete all as specified and directed.

M&L for submain wiring with 2X6.0 Sqmm+1X6.0 Sqmm Earth Wire single core PVC insulated FRLS-H, PVC sheathed cooper cable connecting to common earth dolly in and including heavy duty PVC conduit, with all accessories complete all as specified and directed. Note: Three runs of copper wire for phase, neutral, earth & one run PVC conduit/ casing shall be measured one unit length.

S&F sheet metal enclosure MCB, DB, 8 way, SPN, double door suitable for 240 V, 200 amps, IP-54, rated bus bar/ DIN rail, fixed and flushed on walls including cutting Knitch and making good disturbed surfaces, complete all as specified and directed. Make : L&T / Legrand / Schineider.

S&F sheet metal enclosure MCB, DB, 4 way, SPN, double door suitable for 240 V, 200 amps, IP-54, rated bus bar/ DIN rail, fixed and flushed on walls including cutting Knitch and making good disturbed surfaces, complete all as specified and directed. Make : L&T/ Legrand/ Schineider.

S&F MCB, SP (single pole) 05 to 32 Amps, 10 kA, B Curve for inductive load connected through cable lugs of suitable size, complete all as specified and directed. Make : L&T/ Legrand/ Schineider.

S&F MCB, SPN (single pole and neutral) 40 Amps for inductive load connected through cable lugs of suitable size, complete all as specified and directed. Make : L&T/ Legrand/ Schineider.

S&F MCB, TPN (Triple pole Neutral) 40/63 Amps for inductive load connected through cable lugs of suitable size complete all as specified and directed. Make: L&T/ Legrand/ Schneider.

S&F sheet metal enclosure MCB DB 4 way VTPN double door suitable for 240 V, 200 amps, IP-54, rated bus bar/ DIN rail, fixed and flushed on walls including cutting Knitch and making good disturbed surfaces complete all as specified and directed. Make: L&T/ Legrand/ Schneider.

S&F 4 Pole, MCCB, 63 Amp, 50 Hz, 415 V with rupturing capacity 36 KA, connected through cable lugs of suitable size complete all as specified and directed. Make: L&T/ Legrand/ Schneider.

M&L for Earthing complete with galvanised steel earth plate electrode 60×60cm×6mm thick, buried directly in ground (earth pit not less than 2.25 meters deep below ground level) with top edge of the plate not less than 1.5 meters below normal ground level, connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 connected to earthing test point all as specified or indicated including testing on completion including galvanised strip protected by 32 mm bore light grade galvanised iron pipe and earth and connected to test point as directed including funnel, watering pipe 20 mm bore light grade galvanised iron wire mesh charcoal and common salt in alternate layers of 15 cm compacted thickness all around the GI electrode with concrete pit in PCC 1:3:6, type C-1, including necessary excavation in soft/loose soil and disposal of soil to a distance not exc 50 m and necessary testing complete connected to earthing test point, complete all as specified and directed.

All as per Srl Item No 125.00 above but for using galvanised iron strip 32x6mm as earthing lead, complete all as specified and directed.

M/S Shiv Kumar (BID ID -3493302)