REPAIR TO CEILING, FLOORING, JOINERY, SANITARY FITTING AND PERIODICAL SERVICES TO CERTAIN BUILDING AT INS AGRANI COIMBATORE

Amount

Dismantling Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings.

Dismantling of Asbestos cement (corrugated, semi-corrugated, etc.) sheets in roof coverings.

Demolition Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets.

Dismantling structural steel work including doors, gates but excluding framed truss etc

Demolition of Cement Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level)

M&L for Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240 with one shop coat of zinc chromate primer (including preparation of surface) complete all as specified and directed.

M&L for pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

M&L for pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F anodised aluminium snap grid frame work for false ceiling with size of grid 605x605mm with and including hangers 6mm dia GI (upto 1200mm length ) adjusting level fix to roof by means of ceiling, cleats made out of GI flat 40 x 3mm size 60 mm long and expansion hold fasteners 12.5mm dia 40mm long and providing and fixing 12mm thick gypsum board fixed with screw and incl provn of two coats of plastic emulsion paint over one coat of primer including necessary scaffolding complete all as specified and directed.

M&L Preparation of steel surfaces of tubular trusses over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint complete all as specified and directed. (Note: Cost of applying primer is included in the item No.06 hereinabove)

M&L for 40mm thick plain cement concrete 1:2:4 type B1 using 20mm graded stone aggregate as in floor finished even and smooth without using extra cement complete all as specified and directed.

Demolition of stone slabs and tiles of any description or thickness laid, bedded and pointed in any mortar including cement mortar backing coat complete all as specified and directed.

M&L screed bed or bedding layer of mortar 15mm thick in CM 1:6 for laying floor finishes etc. complete all as specified and directed. .

M&L Non-Skid coloured ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floor etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

M&L Rendering 10 mm thick on fair face of brick work or on concrete surface in CM 1:4 (for fixing tiles) complete all as specified and directed.

M&L Non-Skid coloured ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in vertical surface (skirting) etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

M&L Glazed Ceramic coloured tile in vertical surface size 300x200x8 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match complete all as specified and directed

Demolition of reinforced cement concrete as in roofs, floors (other than ground floors), beams, landing, chajjas and similar suspended work

M&L for reinforced cement concrete 1:2:4 type B0, (nominal mix) using 12.5mm graded stone aggregate in chajjas complete all as specified and directed

M&L Formwork for rough finished surface of concrete flat to chajjas,troughs and similar work including edges in any height in four story buildings including necessary scafolding complete all as specified and directed

M&L for TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed

M&L Rendering 10mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4, finished to an even and smooth surface without using extra cement complete all as specified and directed.

M&L for preparation of newly plastered surface of wall and applying two coats of cement based paint over a coat of alkali resistant primer complete all as specified and directed.

Supply only Integral waterproofing compound (ISI marked)

M&L Repairs to damaged portion of RCC chajja fins and RCC parappet fins etc at any height in 2 storey building with PCC 1:2:4, type B0 using 12.50 mm graded stone aggregate incl necessary scafolding work, form work, rendering on RCC work etc to match with the existing surfaces, complete all as specified and directed.

Dismantling of brick tiles or terracing tiles / Tarfelt single layer on roof and removing the deberis out side MD land complete all as specified and directed.

Demolition of cement concrete of any descriptiion and in any position and removing the deberis out side MD land complete all as specified and directed.

M&L for Plain cement concrete 1:2:4 type B1 using 20mm graded stone aggregate in cast in situ bed plates complete all as specified and directed

M&L for 15 mm thick water proofing cement plaster in CM 1:3 mixed with approved water proofing liquid finished even and smooth on concrete surfaces complete all as per specified and directed.

Supply only liquid water proofing compound of approved make.

M&L Mirror polished Kota stone slab 20-25mm thick in floor jointed with grey cement slurry mixed with pigment to match the shade of the slab, laid over and including screed bed in CM 1:6 (15mm thick) and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing complete all as specified and directed.

M&L Mirror polished Kota stone slab 15-20 mm thick in riser of steps ( in single piece), skirting, dado and pillar jointed with grey cement slurry mixed with pigment to match the shade of the slab, laid over and including rendering in CM 1:4 (10mm thick) and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing complete all as specified and directed.

Dismantling of cast iron or reinforced concrete drain pipes, jointed in cement mortar and taking out of trenches, if required fixed on wall,110/75/50mmdia, including all fittings.

S&F PVC (SWR) pipes 110 mm dia single socketed in any length as in rain water pipe, with rubber rings fixed to wall all as specified and directed .

Dismantling expanded metal, any thickness or mesh, fixed with steel or wood fillets, if any,weight not exeeding 4 KG per sqm.

Taking down Chowkhats or frames with shutters area not exc. 1.5 sqm each without taking off shutter from the frame complete all as specified and directed.

Taking down Chowkhats or frames with shutters area exc 1.5 sqm but n exc 4 sqm each without taking off shutter from the frame complete all as specified and directed.

Taking down shutters of any description area exc 1 sqm but nexc 2 sqm complete all as specified and directed.

Taking down shutters of any description area exc 2 sqm complete all as specified and directed.

M&L Expanded metal weight per sqm not exe 4 Kg, cut to length, bent to shape required and tying with and including annealed mild steel wire not less than 0.9mm dia or fixing with galvanised steel staples to wood or steel members complete all as specified and directed.

M&L for IInd class hard wood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, including tarring with a coat of tar and sanding the back or surfaces contacted with concrete or mortar complete all as specified and directed.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, in opening as per SSR specification & drawing complete all as specified and directed

S & F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement or stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, complete all as specified and directed

S&F 2nd class hard wood Glazed and skeleton shutters 30mm thick for ventilators open rebated and prepared to receive glass, gauze, etc. divided in to squares, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc, sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats all as specified and as directed.

S&F 2nd class hard wood plain framed, factory made panelled shutter 35mm thick (any number of panels) with lock rail and panel of 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated all as specified and as directed.

M&L for 75mm long aluminium anodised barrel tower bolt (ISI Marked) of extruded section complete all as specified and directed.

M&L for 150mm long aluminium anodised barrel tower bolt (ISI Marked) of extruded section complete all as specified and directed.

S&F 250mm long Aluminium alloy, anodised, sliding door bolt (ISI Marked) with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed .

S&F butt hinges medium weight cold rolled mild steel 75 mm size complete all as specified and directed..

S&F butt hinges medium weight cold rolled mild steel 100mm size complete all as specified and directed..

S&F Extruded aluminium alloys handles cast type anodized of size 75mm long complete all as specified and directed.

S&F Extruded aluminium alloys handles cast type anodized of size 150mm long complete all as specified and directed.

S&F in repair Aluminium Hat pegs, solid body,125mm to 175 mm complete all as specified and directed.

S&F 100mm Hasp and staple, safety type, aluminium with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and directed.

S&F in repair Harrison rails, mild steel, chromium plated with fixing brackets, stops, rollers etc complete all as specified and directed.

S&F in repair Aluminium Tubular towel rail, 20mm dia, D type, 60cm long between flanges complete all as specified and directed.

S&F In repair double action spring hinges mild steel with steel wire spring stove enamelled, 150mm

S&F Door closer cast iron body hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg complete all as specified and directed.

S&F Aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples complete all as specified and directed.

S&F in repair Aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples complete all as specified and directed.

S&F 3.00mm thick sheet glass, plain and glazing with oil putty in square n exc. 0.5 sq m each pane complete all as specified and directed.

S&F 3.00mm thick sheet glass, plain and glazing with oil putty in square n exc. 0.5 sq m each pane including hacking out old brocken glass of any description complete all as specified and directed.

S&F 15 mm bore pillor tap ,cast copper alloy with capstan heads,chromium plated screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts, screwed for iron/ PVC pipe complete all as specified and directed.

S&F in repair Mortice lock, vertical type, size 100 mm mild steel 4 levers complete all as specified and directed.

M&L preparation of new painted wooden surface of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and directed.

S&F MS holdfast made out of flat iron 25X3mm size complete all as specified and directed.

M&L PCC 1:2:4, type B0 using 12.5mm graded stone aggregate as in bed plate for holdfast complete all as specified and directed.

S&F in repairs sinks with drainage board made of stainless steel 1mm thick (kitchen or laboratory) with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm with Waste coupling 40mm dia of PTMT (half or full threaded) (Minimum weight 32mm- 45gms/40mm-60 gms) complete all as specified and directed .

S&F in repairs Vitreous china wash basin white ( flat back or angle back type ) of size 550x400 but including brackets , including cutting for pinning in ends of brackets or erecting stand and waste pipe fixed (Includes fixing only of tap & waste coupling) and provn of pillar taps 15mm cast copper alloy with capstan heads , Chromium plated screwed down high pressure with or without lettered "Hot " or "cold" with long screwed shanks and fly nuts , screwed for iron pipes complete all as specified and directed.

S&F in repair vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) complete all as specified and directed.

S&F Vitreous china superior coloured wash down water closet pedestal pattern (P or S trap) with seat cover and with all fittings and connections complete all as specified and directed (Make:Hind ware model No. C0466 or equivalent model of any other manufacturers from the list)

S&F 10 ltr capacity PVC valve less, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets complete all as specified and directed.

S&F in repair Soap dish (stainless steel) , fixed to plugs with chromium plated brass screws

M&L Preparation of old treated surfaces of wall and applying one coat of white wash complete all as specified and directed.

M&L Preparation of old treated surfaces of ceiling and applying one coat of white wash complete all as specified and directed.

M&L Preparation of old treated surfaces of wall and applying one coat of cement based paint complete all as specified and directed.

M&L Preparation of old treated surfaces of wall and applying one coat of distemper oil emulsion complete all as specified and directed.

M&L Preparation of old painted surface of wood of any description over 10 cm in width or girth and applying one coat of synthetic enamel paint complete all as specified and directed..

M&L Preparation of old painted steel surface of any description over 10cm in girth or width and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L writing letters or figures (Block , Roman, Italic or Indian ) n exc 30 cm high complete all as specified and directed..

M&L for preparation of old decorated surface of wall and applying one coat of antifungal paint (Apex Ultima Protek of Asian paint or equivalent of Berger / Nerolac / Dulux) duly applied through authorised company applicator using modern tools and techniques complete all as specified and as directed.

M&L complete removal of existing treatment by scouring, washing down with water jet on internal surfaces of walls including preparing of old plastered surfaces, and applying two coats of distemper oil emulsion (Asian paint Royale or equivalent of other make given from list of manufacturer) over a coat of alkali resistant primer all as specified and as directed

SRI AMMAN & CO