NOW Repair and maintenance of infrastructure assets in CP division during 2026-27. SH Replacement of old damaged gym equipment at CPWD complex Hanuman Road Connaught place.

DOUBLE AIR WALKER / Health Walker for two person Providing and fixing Double Air Walker made from “C” class GI Pipe hot dip galvanised (Make-Jindal & equivalent) . U main frame pipe 80mm. GI C Class pipe (4 to 4.5mm thickness) .Bottom main frame 114mm. GI C Class pipe (4 to 4.5mm thickness). Handle Pipe 32mm. GI C Class pipe (4 to 4.5mm thickness)and the bottom support of M.S. round plate of 250 mm dia & 10mm thickness is welded at bottom. MS plate of 245 x 113 x 2.8mm :- Footrest support plate. The leg movement frame is of 40mm NB made from “C” Class MS pipe. The handle frame is of 25mm NB made from “C” Class GI pipe. The foundation used for fixing is consists of three equal items i.e. 80mm NB made from “C” Class GI pipe, M.S. Round Plate of 250 mm dia & 10mm thickness & 25 mm X 25mm M.S. angle of 3 mm thickness. MS pipe 48 x 48 x 2.8mm:- Footrest frame support. MS Angle 23 x 23 x 1.8mm:- Foundation support frame. MS Flat 48 x 9mm:- Foundation plate support. MS bright material:- Pins made of Dia.25mm. MS plate of 8mm:- Air Walker Pedal L-bend, support. 60mm dia seamless pipe:- Bushes. Bearings:- Permanent lubricated bearings 6205. Closing Caps made from top quality FRP material with 2 mm thickness. HDPE / LLDPE Plastic:- Closing cap, Air Walker Footrest. The pins used are made up of 25mm diameter bright bar. The bearings used be permanent lubricated sealed bearing of reputed make"SKF/ NTN/ NACHI/FAG/NRB'. The nut bolts used for assembly are made from S.S. material. The serclips used for assembly are of 25 mm diameter. The Gym Equipment shall be finished smooth with a primer coating of at least 40 micron followed by epoxy based Powder Coating with Polyester Powder Coating of at least 60 to 70 micron thickness using Exonobel / Berger make paints or its equivalent paints. The holding down/fixing of Gym Equipments shall be fixed on existing cement concrete foundation

DOUBLE SEATED CHEST PRESS /PUSH CHAIR made from “C” Class G.I pipe hot dip galvanised (Make-Jindal & equivalent). Center main pipe114mm. GI C Class pipe (4 to 4.5mm thickness). Sitting pipe 40mm. GI C Class pipe (4 to 4.5mm thickness). Both side vertical structure pipe 40mm.. Bottom support is of M.S. round plate of DIA 250 mm & 10mm thickness welded. All linkages are made up of 25NB “C” class G.I. pipe. The handle frame is of 32NB “C” class G.I. pipe. . To build structure bushes are used which are made from seamless pipe of 60mm O.D. and 4 to 4.5mm thickness as well as 60mm diameter solid bar bush used. Welded with M.S. round plate of DIA 250 mm & 10mm thick. Main pipe supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness. Foundation Cover Closing Cap is made from Injection Mould Plastic LLDPE / HDPE. The seats and Back rests are fitted on the outer frames are made up of M.S. Sheet of size 330 mm X 300 mmX3mm thickness and deep drawn metallic and pressed in tools and dies to have uniform radius of 20 mm with no sharp edges. Closing Caps are made up of from Injection Moulded Plastic LLDPE / HDPE. Handgrip material is EPDM rubber.Pins used of Diameter 25mm and 17mm are made up from SAE 8620 bright material. The bearings used are of “6205 2RS1” and “6203 2RS1” permanent lubricated sealed bearing of reputed brand "SKF/ NTN/ NACHI/FAG/NRB'. High tensile steel with galvanized nuts & bolts are used for assembly. The cerclips used for assembly are of A16. The Gym Equipment shall be finished smooth with a primer coating of at least 40 micron followed by epoxy based Powder Coating with Polyester Powder Coating of at least 60 to 70 micron thickness using Exonobel / Berger make paints or its equivalent paints. The holding down/fixing of Gym Equipments shall be fixed on existing cement concrete foundation .

WAIST TWISTER FOR 3 PERSONS / TRIPLE TWISTER Triple Twister equipment made from “C” Class G.I. pipe hot dip galvanised (Make-Jindal & equivalent) of different NB. NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters. The Center Pipe is of 100mm NB made from “C” Class G.I. Round Pipe. The M.S. round plate of DIA 250 mm & 10mm thickness is welded at bottom. The standing frame of the Double twister is of 32 NB made from “C” class G.I. pipe. The handle frame of double twister is 25 NB. The foundation used for fixing is a structure and made from center pipe of G.I. of 80 NB “C” class, Welded with M.S. round plate of DIA 250 mm & 10mm thick. Main pipe supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness. The Twister plate fitted on the standing frame is made up of M.S. Round Plate of size 300mm diameter and 10mm thickness. Closing caps made from top quality Fiber reinforced Plastic material which is of 2 mm thick. The Pins used are made up of DIA 25 mm MS bright material. The bearings used are of “6205zz” permanent lubricated sealed bearing of reputed brand SKF/ NTN/ NACHI/FAG/NRB . High tensile steel with galvanized nuts & bolts are used for assembly. The Gym Equipment shall be finished smooth with a primer coating of at least 40 micron followed by epoxy based Powder Coating with Polyester Powder Coating of at least 60 to 70 micron thickness using Exonobel / Berger make paints or its equivalent paints. The holding down/fixing of Gym Equipments shall be fixed on existing cement concrete foundation .

HD HANGING WHEEL Providing and Fixing of HD Hanging Wheels made from "C" Class GI Pipe(Make-Jindal & equivalent), Pre Galvanized Mild Steel, Material Thickness MINIMUM 4- 4.5 mm, Sealed Ball Bearing, Steel Seats for long lasting life. The Gym Equipment shall be finished smooth with a primer coating of at least 40 micron followed by epoxy based Powder Coating with Polyester Powder Coating of at least 60 to 70 micron thickness using Exonobel / Berger make paints or its equivalent paints. TThe bearings used are of “6205zz” permanent lubricated sealed bearing of reputed brand SKF/ NTN/ NACHI/FAG/NRB . High tensile steel with galvanized nuts & bolts are used for assembly. The Gym Equipment shall be finished smooth with a primer coating of at least 40 micron followed by epoxy based Powder Coating with Polyester Powder Coating of at least 60 to 70 micron thickness using Exonobel / Berger make paints or its equivalent paints. The holding down/fixing of Gym Equipments shall be fixed on existing cement concrete foundation .

PULL DOWN CHALLENGER/SEATED PULLER /PULL CHAIR DOUBLE made from “C” Class G.I pipe hot dip galvanised (Make-Jindal & equivalent). Center main pipe114mm. GI C Class pipe (4 to 4.5mm thickness). Sitting pipe 40mm. GI C Class pipe (4 to 4.5mm thickness). Both side vertical structure pipe 40mm.. Bottom support is of M.S. round plate of DIA 250 mm & 10mm thickness welded. All linkages are made up of 25NB “C” class G.I. pipe. The handle frame is of 32NB “C” class G.I. pipe. . To build structure bushes are used which are made from seamless pipe of 60mm O.D. and 4 to 4.5mm thickness as well as 60mm diameter solid bar bush used. Welded with M.S. round plate of DIA 250 mm & 10mm thick. Main pipe supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness. Foundation Cover Closing Cap is made from Injection Mould Plastic LLDPE / HDPE. The seats and Back rests are fitted on the outer frames are made up of M.S. Sheet of size 330 mm X 300 mmX3mm thickness and deep drawn metallic and pressed in tools and dies to have uniform radius of 20 mm with no sharp edges. Closing Caps are made up of from Injection Moulded Plastic LLDPE / HDPE. Handgrip material is EPDM rubber.Pins used of Diameter 25mm and 17mm are made up from SAE 8620 bright material. The bearings used are of “6205 2RS1” and “6203 2RS1” permanent lubricated sealed bearing of reputed brand "SKF/ NTN/ NACHI/FAG/NRB'. High tensile steel with galvanized nuts & bolts are used for assembly. The cerclips used for assembly are of A16. The Gym Equipment shall be finished smooth with a primer coating of at least 40 micron followed by epoxy based Powder Coating with Polyester Powder Coating of at least 60 to 70 micron thickness using Exonobel / Berger make paints or its equivalent paints. The holding down/fixing of Gym Equipments shall be fixed on existing cement concrete foundation .

CHIN UP & DIPPING BAR Chin up & dipping bar equipment made from “C” Class G.I. pipe hot dip galvanised (Make-Jindal & equivalent) of different NB. NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters. The Center Pipe is of 100mm NB made from “C” Class G.I. Round Pipe. Handles are made up of 40NB G.I Pipe. they are attached with plate 130x50mm to the main frame with the help of fasteners. The foundation stand is made from 100NB GI Pipe having 200x10 thk Plate. The Gym Equipment shall be finished smooth with a primer coating of at least 40 micron followed by epoxy based Powder Coating with Polyester Powder Coating of at least 60 to 70 micron thickness using Exonobel / Berger make paints or its equivalent paints. The holding down/fixing of Gym Equipments shall be fixed on existing cement concrete foundation .

ROWING / SELF WEIGHT ROWER . Rower Equipment made from “C” Class G.I. pipe hot dip galvanised (Make-Jindal & equivalent). of different NB. NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters. The Main frame is of 100NB “C” class G.I. Pipe welded with M.S. round plate of 250mmX10mm. The handle frame 25NB is made from “C” class G.I. pipe. The foundation used for fixing is a structure and made from center pipe of G.I. of 100 NB “C” class Welded with M.S. round plate of DIA 250 mm & 10mm thick. Main pipe supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness. To join the movement frame to main frame connecting links made up from 32 NB G.I. “C” class pipe. The seat fitted on the outer frames are made up of M.S. Sheet of size 330 mm X 300mmX2mm thickness and deep drawn metallic and pressed tools and dies to have uniform radius of 20 mm with no sharp edges. Pins used of Diameter 17mm are made up from SAE 8620 bright material. The bearings used are of “6203zz” permanent lubricated sealed bearing of reputed brand "SKF/ NTN/ NACHI/FAG/NRB'. High tensile steel with galvanized nuts and bolts are used for assembly. The P.U. bushes (Stopper) used to avoid the collision. The circlips used for assembly is of A 16. The Gym Equipment shall be finished smooth with a primer coating of at least 40 micron followed by epoxy based Powder Coating with Polyester Powder Coating of at least 60 to 70 micron thickness using Exonobel / Berger make paints or its equivalent paints. The holding down/fixing of Gym Equipments shall be fixed on existing cement concrete foundation .

STAIR STEPPER DOUBLE made from “C” Class G.I. pipe hot dip galvanised (Make-Jindal & equivalent). Center main pipe 114mm GI C Class pipe (4 to 4.5mm thickness). Stepping pipe 50mm. square M.S (3.5mm to 3.7mm. thickness). Stepping footrest 4mm checked M.S sheet .Handle Pipe 30mm GI C Class pipe (4 to 4.5mm thickness) The Pins used is made up of 25 mm diameter Harden low carbon steel. The Bearings used is of “6205” permanent lubricated sealed bearing of reputed brand "SKF/ NTN/ NACHI/FAG/NRB'. The Nut Bolts used for assembly are made from S.S. material. The Gym Equipment shall be finished smooth with a primer coating of at least 40 micron followed by epoxy based Powder Coating with Polyester Powder Coating of at least 60 to 70 micron thickness using Exonobel / Berger make paints or its equivalent paints. The holding down/fixing of Gym Equipments shall be fixed on existing cement concrete foundation.

Double cross walker /Cross trainer double Cross Trainer Double made from “C” Class G.I. pipe hot dip galvanised (Make-Jindal & equivalent). Center main pipe 114mm GI C Class pipe (4 to 4.5mm thickness). Stepping pipe 50mm. square M.S (3.5mm to 3.7mm. thickness). Stepping footrest 4mm checked M.S sheet .Handle Pipe 30mm GI C Class pipe (4 to 4.5mm thickness) The Pins used is made up of 25 mm diameter Harden low carbon steel. The Bearings used is of “6205” permanent lubricated sealed bearing of reputed brand "SKF/ NTN/ NACHI/FAG/NRB'. The Nut Bolts used for assembly are made from S.S. material. The Gym Equipment shall be finished smooth with a primer coating of at least 40 micron followed by epoxy based Powder Coating with Polyester Powder Coating of at least 60 to 70 micron thickness using Exonobel / Berger make paints or its equivalent paints. The holding down/fixing of Gym Equipments shall be fixed on existing cement concrete foundation.

SURF BOARD DOUBLE/ AIR SWING FOR TWO Providing and fixing Surf Board made from “C” Class GI pipe hot dip galvanised (Make-Jindal & equivalent) . The center pipe is of 114mm NB made from “C” class GI pipe, and the bottom support of M.S. plate of 250 mm dia & 10mm thickness is welded at bottom. The handle frame is of 40mm NB & 25mm NB made from “C” class GI pipe. The movement frame is made up of 50mm NB “C” class GI pipe. The foundation used for fixing consists of three equal items i.e. 100mm NB made from “C” Class GI pipe, M.S. round plate of 250 mm diameter & 10mm thickness, 25mm X 25mm X 3mm M.S. angle. To join the centre pipe & handle frame seamless pipe of 130mm dia & 3mm thickness is used. For the movement, bushes are used & for it 60mm dia with 3mm thickness & 60mm solid bar is used. The footrests is made from FRP/C.I./Aluminum casting material, its sizes are 320 mm X 270 mm & 5 mm thickness. For support of footrest is 200mm X 250mm with 4 to 4.5mm thickness M.S. Plate and 50mm X 50mm CRC Square pipe with 2mm thickness is used. Closing Caps made from top quality FRP material which is of 2 mm thickness. The pins used are made up of 25 mm diameter Harden bright bar. The bearing used be permanent lubricated sealed bearing of reputed make. The handles used are of Rubber grip. The Nut Bolts used for assembly is made from S.S. material. The bushes (Stopper) used to avoid the collusion made from Polyurethane Plastic material of 50 mm dia. The serclips used for assembly is of 25 mm dia. The Gym Equipment shall be finished smooth with a primer coating of at least 40 micron followed by epoxy based Powder Coating with Polyester Powder Coating of at least 60 to 70 micron thickness using Exonobel / Berger make paints or its equivalent paints. The holding down/fixing of Gym Equipments shall be fixed on existing cement concrete foundation .