SPECIAL REPAIRS TO BLDG NO P-589 ( OR MD ACCN) OF 13 GARH RIF , SPL REPAIRS FOR REWIRING TO BLDG NO P-259 (OFFRS MESS) OF 19 MADRAS AND PROVN OF 05x SECURITY LIGHTS AT 260 FD WKSP COY EME AT PANGODE MIL STN TRIVANDRUM

Amount

Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc laid bedded and pointed in any mortar etc complete all as specified and directed.

M&L for 20 mm thick granite (of any type) work (tabled rubbed and polished) in steps, jambs, pillars, window-cills, cooking platform and like in 20mm thick cement mortar (1:6) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including edges grinding and polishing etc complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding but not backing, remov-ing serviceable tiles to store and rubbish off the premises, complete all as specified and directed by Engr-in-charge.

M&L Glazed ceramic coloured tiles in verticle surfaces 450x300x7mm thick set and jointed in neat cement slurry and pointed in coloured cement to match all as specified and as directed.

M&L for 10 mm thick rendering in cement mortar 1:4 on fair faces of concrete surfaces for backing of tiles etc complete all as specified and directed.

M&L Non skid ceramic coloured tiles 7 to 8 mm thick (square/Rectangular ) area of each tiles exceeding 0.06 Sqm but not exceedng 0.11 sqm, as in floors etc, set and jointed neat cement slurry and pointed with colour cement to match etc complete all as specified and directed. .

M&L for 15 mm thick screed bed in cm 1:6 for laying floor finishes (Upto four storey building) etc complete all as specified and directed.

Taking down chowkats or frames including shutters (without taking off shutters from the frames) not exceeding 1.50 Sqm each, complete all as specified and directed by Engr-in-charge.

S&F Factory made solid panel PVC door shutter 30mm thick (stile) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC ' C' channel having a PVC sheet strip of 20 mm width struck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rails and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to in stiles & rails with suitable PVC sheet beading and joinned together with solvent cement supplying & fixing in frames at site as per specification and drawing shown in SSR Part -II, complete all as specified and directed by Engr-in-charge.

S&F Solid PVC door frame of size 50 mm x 47 mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supply & fixing in opening as per specification & drawing shown in SSR Part-II, complete all as specified and directed by Engr-in-charge.

S&F 100mm butt hinges, extruded aluminium with galvanised MS hinge pin, anodised and fixed Type B-21 etc complete all as specified and directed.

S&F Aluminium, anodised, barrel tower bolts of extruded section, 150 mm long, complete all as specified and directed by Engr-in-charge.

S&F Aluminium handles, cast type, anodised of size 150 mm long, complete all as specified and directed by Engr-in-charge.

Hacking out old broken glass (any thickness, size, quality or description) from metal or wooden frame glazed with putty etc, complete all as specified and directed by Engr-in-Charge.

S&F 3mm thick sheet glass ordinary quality, and glazing with oil putty or wooden beads in squares n.exc 0.50 Sqm in each pane, complete all as specified and directed by Engr-in-charge.

S&F 3mm thick obsecured or frosted glass ordinary quality, and glazing with oil putty or wooden beads in squares n.exc 0.50 Sqm in each pane etc, complete all as specified and directed by Engr-in-charge.

S&F in repair Galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanised wire staples, complete all as specified and directed by Engr-in-charge.

Taking down cement plaster, any description, on brick or stone walls or concrete surface, etc. including raking out joints hacking for key, scrubbing down with water etc. complete all as specified and directed by Engr-in-charge.

M&L Rendering 10 mm thick on fair faces of brick work or concrete surfaces in cm 1:4 ,finished even and smooth (without using extra lime or cement) etc complete all as specified and directed.

Preparation of new plastered or unplastered surfaces of walls and applying three coats of white wash, complete all as specified and directed by Engr-in-charge.

M&L Preparing new plastered surface,priming with chalk whiting and applying two coats of OBD on walls etc complete all as specified and directed.

Rendering 10mm thick in CM 1:3 on fair faces of brick work or concrete surfaces on ceiling, finished even and smooth w/o using extra cement, complete all as specified and directed by Engr-in-Charge.

Preparation of new plastered or unplastered surfaces in ceiling and applying three coats of white wash,complete all as specified and directed by Engr-in-charge.

Preparation of old plastered or unplastered surfaces of ceiling and applying one coat of white wash complete all as specified and directed by Engr-in-Charge.

M&L for Applying one coat of acrylic exterior emulsion water proofing painting including prepartion of old surfaces of wall (up to four storey bldg) as per manufactures instructions ) etc complete all as specified and directed.

M&L Washing,rubbing down and stopping of distempered surfaces and applying one coat of oil bound distemper to wall including preparation of surfaces etc complete all as specified and directed.

Brooming down and preparing old surfaces of walls and applying one coat of white wash on old decorated surfaces etc complete all as specified and directed.

M&L Preparation of old wooden surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint (upto four storey building) etc complete all as specified and directed.

M&L Preparation of old surfaces of steel of any description over 10 cm width or grith and applying one coat of synthetic enamel paint etc complete all as specified and directed.

Mild steel framed work such as grills, gratings with ends of bars shouldered or reveted or forged into spikes, framed guard bars, barred Iron doors ladders, framed balusters, walk ways railings, frame work of water tanks and similar works concorming to Fe-290, Gde E-165, (fixed in repair) complete all as specified and directed by Engr-in-charge.

Preparation of new steel surfaces of any description not otherwie described, over 10 cm width or girth and applying two coats of synthetic enamel paint over red oxide, complete all as specified and directed by Engr-in-charge.

S&F in repairs for viterous china, squating pan water closet, orissa pattern, size 580 x 440 mm white with integral foot rests (excluding flushing cistern and flush pipe) including PVC 'P' or 'S' trap and cement concrete and jointing to flush pipe complete all as specified and directed.

S&F in repair 10 ltr capacity PVC, low level, valveless, syphonic action type flushing cistern, inlet ball valve, float valve, handle and fixing arrangement, 32mm dia PVC flushing pipe and 15mm dia 450mm long PVC connection with CP brass coupling nuts and PVC washer at both ends,complete all as spfd and directed by Engr-in-Charge.

S&F 15mm bore UPVC tubing incls taking down the pipe etc complete all as specified and directed.

S&F 20 mm bore UPVC tubing incls taking down the pipe etc complete all as specified and directed.

S&F in repair PVC (SWR) pipes 75mm bore single socketed in any length with rubber ring joints fixed to walls/ floors including necessary brackets etc complete all as specified and directed. (Upto four storey building).

Demolition of Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) etc complete all as specified and directed.

M/L 75mm thick Cement concrete type B-2, 1:3:6 (40mm graded aggregate)finished even and smooth without using extra cement etc complete all as specified and directed.

S&F PVC connection 15mm dia 450mm long with 02 Nos brass check nuts with washer etc fixed in repair etc complete all as specified and directed by Engr -in-Charge

S & F in repair Pillar taps 15mm dia fancy type with capstion heads, chromium plated , screwed down high pressure, with or without lettered 'Hot' or 'cold' with long screwed shanks and fly nuts etc complete all as specified and directed by Engr-in-charge.

S & F in repairs chromium plated brass shower roses 125 mm size with or without swivel joints including fixing to steel pipe or unionetc complete all as specified and directed by Engr-in-charge.

S&F sinks with drainage board made of stainless steel 1mm thic kitchen with plugs, washers and wastes, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mmx460mm bowl size 410mm x 330mm x160mm etc fixd in repair complete all as specified and directed by Engr-in-charge.

S&F in repair 40mm dia of discharge pipe waste coupling of PTMT( half or full threaded) minimum weight 32mm -45/40mm-60grm) complete all as specified and direced by Engr-in-charge.

S&F 40mm dia flexible waste pipe with suitable length for sinks complete all as specified and direced by Engr-in-charege.

S&F Vitreous china, wash hand basin, (white) of size 550mmx400mm including brass CP waste coupling 32mm dia with long screwed shank and fly nuts, PVC medium grade 32mm dia waste pipe, chain and plug, porcelain stopper , PVC connection 15mm dia, 450mm long with brass CP nuts and washers at both ends (fixed in repair), complete all as specified and directed by Engr-in-Charge.

S&F Pillar tap, cast copper alloy, with capstan head, chromium plated screwed down high pressure, with or without lettered hot/cold with long screwed shanks and fly nuts screwed for iron pipe 15mm borecomplete all as specified and directed by Engr-in-Charge.

S&F in repair Bib tap fancy type chromium plated 15mm dia with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed etc complete all as specified and directed.

S & F in repairs Stop valve 15 mm dia, fancy type chromium plated screwed down, high pressure with long shank and cup screwed both ends for unions and fixed, all as specified by Engineer -in-Charge.

Taking down shutters of any description not exceeding 1.00 Sqm eachcomplete all as specified and directed by Engr-in-charge.

Taking down shutters of any description exceeding 1.00 Sqm and not exceeding 2.00 Sqm each, complete all as specified and directed by Engr-in-charge.

S&F for 35 mm thick 2nd class hard wood plain framed , panelled shutters ( any number of panels ) with panels of timber flat on both sides ( feathered edged) or of vennered particle board medium density , wood particle board with commercial face veneers supplied and fitted to chowkats etc complete all as specified and directed.

M&L 2nd class hard wood factory made glazed and skeleton shutters 35 mm thick, open rebated and prepared to receive glass or gauge,etc. (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut & mitred beads for securing gauge sizes of members of shutters as specified in SSR Part-I Section-8, clause 8.24 (a) for door shutter supplying and fitted to chowkats, etc complete all as specified and directed.

S&F for 2nd class hard wood glazed skelton shutters 30 mm thick for windows and ventilators open rebated and prepared to receive glass/guage etc and rebated sash bar any number divided into squares, with plain chamfered or rounded, mitred beads for securing glass etc; sizes of members of shutters in SSR part-I,section 8,clause 8.24 (a) supplied and fixed to chowakhats etc complete all as specified and directed.

Prepartion of new wooden surfaces of any description not otherwise described, exc 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer, complete all as specified and directed by Engr-in-charge.

S&F Galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanised wire staples, complete all as specified and directed by Engr-in-charge.

S&F Aluminum alloy anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast - aluminum alloy and fixed of 300mm long etc complete all as specified and directed.

S&F Aluminium anodised handles, cast type, anodised of size 100 mm long, complete all as specified and directed by Engr-in-charge.

S&F Aluminium anodised handles, cast type, anodised of size 150 mm long, complete all as specified and directed by Engr-in-charge.

S&F Mild steel cold rolled Butt hinges, medium weight,100 mm long, complete all as specified and directed by Engr-in-charge.

S&F Aluminium, anodised, barrel tower bolts of extruded section, 100 mm long, complete all as specified and directed by Engr-in-charge.

S&F Aluminium, anodised, barrel tower bolts of extruded section, 150 mm long, complete all as specified and directed by Engr-in-charge.

S&F Mild steel cold rolled Butt hinges, medium weight,75 mm long, complete all as specified and directed by Engr-in-charge.

S&F Grating doom 100mm dia of PTMT(minimum weitht 25gms) fixed in repair complete all as specified and directed by Engineer-in-charge

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials and making good disturbed surfaces of walls, floors, etc.complete all as directed

Point wiring complete for One light point controlled by one switch with 1.5 sqmm single core PVC insulated unsheathed FRLS cable 1100 volts grade with multi stranded, copper conductor in and including non-metalic PVC conduit incl accessories totally concealed in wall, ceiling/roof etc., with pressed steel terminal boxes of suitable size & modules, concealed in walls incl plastic laminated sheet cover 3mm thick as top cover fixed with cadmium plated screws for housing switches/sockets/regulators etc, including provn of 1.5 sqmm nominal cross sectional area, PVC insulated, FRLS, unsheathed, 1100 volt grade, multistranded single core green colour copper conductor for earth continuity connected to earth dolly all as directed NOTE: Pressed steel terminal boxes with a coat of synthetic enamel paint over a coat of red oxide to steel surface to avoid rust incl suitable thick laminated sheet cover plate for mounting switch/sockets/regulator/bell push etc, concealed in wall and Cost of cutting chases & making good to distrubed surface with cement mortar, if required any shall be deemed to be included in the quoted rate Make: Havells or equivalent make of Finolex/Nicco/Plaza/Anchor/Polycab/RPG

All as per ser item No. 66 above but for One fan point controlled by one way switch and regulator

All as per ser item No. 66 above but for One bell/buzzer point controlled by one bell push button independent.

All as per ser item No. 66 above but for one 5 Amps outlet on same board with other switches/sockets

All as per ser item No. 66 above but for one 5 Amps socket outlet on independent board.

All as per ser item No. 66 here in above but point wiring with 2.5 Sqmm FRLS cable and 2.5 sqmm cable earth continuity wire for one 3 pin socket outlet,15 Amps on independent board.

S&F switch piano, flush type, single pole, one way 5 Amp, 240 volt, white or ivory ISI marked complete all as specified Make: Anchor or equivalent make of Havells/Legrand/Cona/Crabtree

S&F bell push, flus type, single pole, one way, 5 Amps, 240 Volts all as directed Make: Anchor or equivalent make of Havells/Legrand/Cona/Crabtree

M&L for stepped type electronic fan regulator, flush type 240 Volts, 50 Hz, suitable for ceiling fan any sweep all as directed Make: Anchor or equivalent make of Havells/Legrand/Cona/Crabtree

S&F switch socket outlet 5 pin, 5 Amps, 240 volts complete all as specified Make: Anchor or equivalent make of Havells/Legrand/Cona/Crabtree

S&F switch socket combination 2 in 1, 5 pin, 5 Amps flush type 240 volts, white or ivory ISI marked complete all as specified Make: Anchor or equivalent make of Havells/Legrand/Cona/Crabtree

S&F switch socket combination 2 in 1, 5 pin, 5/15 Amps flush type, universal, 240 volts, white or ivory ISI marked complete all as specified Make: Anchor or equivalent make of Havells/Legrand/Cona/Crabtree

Point wiring complete for One light point controlled by one switch with 1.5 sqmm single core PVC insulated unsheathed FRLS cable 1100 volts grade with multi stranded, copper conductor in and including non-metalic PVC conduit incl accessories totally concealed in wall, ceiling/roof etc., with modular metal flush boxes of suitable size & modules, concealed in walls with modular white plated cover as top cover fixed with screws for housing switches, socket outlets, fan regulators etc, including provn of 1.5 sqmm nominal cross sectional area, PVC insulated, FRLS, unsheathed, 1100 volt grade, multistranded single core green colour copper conductor for earth continuity connected to earth dolly all as directed NOTE: Cost of modular metal flush boxes with a coat of synthetic enamel paint over a coat of red oxide to steel surface to avoid rust, concealed in wall with suitable white cover plate for mounting switch/sockets, regulator, bell push etc and Cost of cutting chases & making good to distrubed surface with cement mortar, if required any shall be deemed to be included in the quoted rate Make: Havells or equivalent make of Finolex/Nicco/Plaza/Anchor/Polycab/RPG

All as per ser item No. 78 above but for One fan point controlled by one way switch and regulator

All as per ser item No. 78 above but for One bell/buzzer point controlled by one bell push button independent.

All as per ser item No. 78 above but for one 5 Amps outlet on same board with other switches/sockets

All as per ser item No. 78 above but for one 5 Amps socket outlet on independent board.

All as per ser item No. 78 here in above but point wiring with 2.5 Sqmm FRLS cable and 2.5 sqmm cable earth continuity wire for one 3 pin socket outlet,15 Amps on independent board.

All as per ser item No. 78 here in above but point wiring with 4.0 Sqmm FRLS cable and 4.0 sqmm cable earth continuity wire for one 3 pin socket outlet,15 Amps on independent board.

S&F modular switch 1 way 6A, 240 volts, 1 module complete all as specified and directed Make: Anchor or equivalent make of Havells/Legrand/Cona/Crabtree

S&F modular switch 1 way 16A, 240 volts, 1 module complete all as specified and directed Make: Anchor or equivalent make of Havells/Legrand/Cona/Crabtree

S&F modular bell push, one way, 6 Amps, 240 Volts, 1 module complete all as directed Make: Anchor or equivalent make of Havells/Legrand/Cona/Crabtree

S&F modular fan step regulator, 120 W - 2 module, 240 Volts, 50 Hz, suitable for ceiling fan any sweep all as directed Make: Anchor or equivalent make of Havells/Legrand/Cona/Crabtree

S&F modular socket, 6A, 240 volts, 2/3 pin combined 2 module, flush type all as specified and directed Make: Anchor or equivalent make of Havells/Legrand/Cona/Crabtree

S&F modular socket, 6A/16A, 240 volts, 2/3 pin combined 2 module flush type all as specified and directed Make: Anchor or equivalent make of Havells/Legrand/Cona/Crabtree

S&F ceiling rose surface PVC/Polycarbonate, isolated body with face Bakelite 65x50 mm three terminal complete all as specified Make: Anchor or equivalent make of Havells/Legrand/Cona/Crabtree

S&F Lamp holder angular type, PVC/Polycarbonate type with back plate suitable for batten fittings complete all as directed Make: Anchor or equivalent make of Havells/Legrand/Cona/Crabtree

S&F buzzer, Ding Dong, AC, 240 Volts, single pole all as directed Make: Anchor or equivalent make of Havells/Legrand/Cona/Crabtree

M&L for distribution board, vertical, made out of sheet metal enclosure (CRCA sheet) dust and vermin proof, double door, VTPN 4 way, 415 volts grade with insulated rated bus bar with nickel plated brass, isolated neutral bar and door earthing, earth bar IP- 43 protection with poly urithene (PU) gasketing, IK-08 Mechanical impact resistance, door earthing flush to wall, including testing suitable for fixing MCCB, MCB TP/SPN/SP etc, including taking down existing unserviceable one and removing from site complete all as specified and directed Make: Cat No. 507745 of Legrand or equivalent of L&T/ABB/Havells/Siemens/Schneider/Indoasian

S&F sheet steel metal enclosure single pole & neutral with a 2 pin and earth plug and socket complete with one single pole MCB SP 20 Amp, 240 volts complete all as specified and directed. Make: Indo Asian or equivalent make of L&T/Legrand/Havells

M&L for distribution board made out of sheet metal enclosure (CRCA sheet) dust and vermin proof, double door, TPN 4 way, 415 volts grade with 200 Amps insulated rated bus bar with nickel plated brass, isolated neutral bar and door earthing, earth bar IP- 43 protection with poly urithene (PU) gasketing, IK-08 Mechanical impact resistance, door earthing flush to wall, including testing suitable for fixing MCB SPN, SP etc, including taking down existing unserviceable one and removing from site complete all as directed Make: Legrand or equivalent in L&T/ABB/Havells/Siemens/Schneider/Indoasian

All as per ser item No. 96 above but for SPN 12, 240 volts grade with 200 Amps insulated rated busbar

S&F in replacement of MCCB triple pole and neutral (four pole) 125 Amp, 415 volts, 50 Hz, having thermal setting range 70% to 100% and adjustable magnetic setting and breaking capacity 25 KA including making incoming and outgoing connections complete all as specified and directed Make: Cat No. 420056 of Legrand or equivalent of L&T/ABB/Havells/Siemens/Schneider/Indoasian

M&L for distribution board made out of sheet metal enclosure (CRCA sheet) dust and vermin proof, double door, SPN 8 way, 240 volts grade with 200 Amps insulated rated bus bar with nickel plated brass, isolated neutral bar and door earthing, earth bar IP- 43 protection with poly urithene (PU) gasketing, IK-08 Mechanical impact resistance, flush to wall, including testing suitable for fixing MCB SPN, SP etc, including taking down existing unserviceable one and removing from site complete all as specified and directed Make: Legrand or equivalent of L&T/ABB/Havells/Siemens/Schneider/Indoasian

S&F MCB single pole 5 to 32 Amps current carrying capacity, 240 volt rating, 10 KA, C curve with IP-20 protected terminals including contact indication window, IP-20 protection, energy limitation Class-3, airflow channels on both sides, bi-connect terminals etc., complete with connection, testing and commissioning and taking down old unsv one from the site complete all as directed Make: Legrand or equivalent in L&T/ABB/Havells/Siemens/Schneider/Indoasian

All as per ser item No. 100 above but for MCB SPN 25 to 32 Amps

All as per ser item No. 100 above but for MCB TP 63 Amps

All as per ser item No. 100 above but for MCB TPN 63 Amps

Supply and fixing sub main wiring with 4 runs of 6.0 sqmm single core, multi-stranded PVC insulated, FRLS unsheathed cable 1100 Volts grade with copper conductor drawn through and including concealed non metalic PVC conduit, medium grade, ISI marked, suitable size with conduit fittings and accessories concealed in wall/ceiling/floor including 2 runs run of 6.0 Sqmm multistranded PVC insulated FRLS, copper conductor cable as earth continuity conductor and connecting to common earth dolly complete. NOTE: Four runs of 6.0 sqmm copper cable and two run of 6.0 sq mm copper cable alongwith non metallic PVC conduit/conduit accessories will be measured as one unit length Make: RRKabel/Finolex/Plaza/Havells/Anchor/Finolex/V-Guard/MESCab

All as per ser item No. 104 above but for sub main wiring with 2 run of 6 sqmm & 1 run of 6 sqmm as earth wire

Taking down carefully existing serviceable Ceiling fan/Wall mounted fan, ceiling cable end, etc., removing the fan for keeping in safe custody, hanging the ceiling fan with down rod after rewiring including clamps, hooks, holdfasteners etc and connecting up, including making electric connection from ceiling rose or connector to fan complete all as directed

Taking down carefully existing serviceable exhaust fan, ceiling cable end, etc., removing the fan for keeping in safe custody, fixing the exhaust fan connecting up after rewiring, including making electric connection from ceiling rose/connector to fan complete all as directed

Taking down carefully existing serviceable Geysers of capacity 25 ltrs, ceiling cable end, etc., removing the geyser for keeping in safe custody and refixing geyser with provn of new suitable MS bolts, grouted to wall and connecting up including provn of new 3 core sheathed multi-stranded flexible copper conductor cable, writing MES No. including making good to the disturbed surface and testing complete all as directed

Dismantling and taking down carefully existing serviceable tube light single/double of any wattage or size street light fittings for repair or replacement of burnt/worn out accessories or carrying to MES store for keeping in safe custody, refixing the same at its original location after wiring, including making electric connection from connector to light fittings & connecting up, testing the same for smooth operation complete all as specified and directed

S&F LED lights fitting 1x 20W, 220V, AC decorative box type with driver, double sided connection, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose, including taking down existing unserviceable one and removing from site complete all as specified and directed. NOTE: LED tube light and LED batten fittings should be two different items. Make: Havells or equivalent make of Philips/Bajaj/Wipro/Osram/GE

S&F LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed. Make: Havells or equivalent make of Philips/Bajaj/Wipro/Osram/GE

S&F LED roadway luminaries 35 Watt, 230 V AC outdoor type with epoxy black powder coated sheet, high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket of suitable size with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete incl connecting wire with flexible PVC insulated copper cables from ceiling rose to fitting complete and testing, including taking down existing unserviceable one and removing from site complete all as specified and directed. Make: Havells or equivalent make of Philips/Bajaj/Wipro/Osram/GE

Supply and fix sub main wiring with 2 runs of 4 sqmm single core PVC insulated, FRLS, unsheathed cable with stranded copper conductor, 1100 Volts grade drawn through and including non metalic PVC conduit with all fitting such as Tee, Bends, Elbow, etc., fixed surface on wall/ceiling including 4 Sqmm multistranded PVC insulated, FRLS, copper conductor cable as earth continuity conductor and connecting to common earth dolly complete. NOTE: Two runs of 4 sqmm copper cable and one run of 4 sq mm copper cable alongwith non metallic PVC conduit will be measured as one length

M&L for Earthing complete in replacement with galvanised iron mild steel earth plate electrode 60 cm x 60 cm x 6.3mm thick burried directly in ground vertically to a depth not less than 2.25 metre below ground level with top edge of earth plate at a depth of not less than 1.5 metre below normal ground level, connected to glavanised earthwire 4mm diameter by means of GI Bolts, Nuts, check nuts and washers including earthing pit in PCC (1:3:6) type C-1 RCC pre-cast (1:2:4 type B-1) cover slab 50 mm thick with 8 mm CTD bars reinforcement both ways at 140 mm centre to centre with two handles, 20 mm dia GI pipe medium grade for watering pipe , wire mesh, funnel and providing charcoal or coke and salt in alternative layers of 15 cm and 15 mm dia light grade GI pipe for protection of earth wire from earth plate to MCB DB including necessary earth work in soft/loose soil, returning, refilling and removing of surplus soil to a distance not exceeding 50 mtr and testing on completion complete all as shown in electrical plate No-3 as specified and directed.

S&F LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed. Make: Havells or equivalent make of Philips/Bajaj/Wipro/Osram/GE

Dismantling and taking down carefully existing serviceable tube light single/double of any wattage or size street light fittings for repair or replacement of burnt/worn out accessories or carrying to MES store for keeping in safe custody, refixing the same at its original location after wiring, including making electric connection from connector to light fittings & connecting up, testing the same for smooth operation complete all as specified and directed

Taking down carefully existing serviceable Ceiling fan/Wall mounted fan, ceiling cable end, etc., removing the fan for keeping in safe custody, hanging the ceiling fan with down rod after rewiring including clamps, hooks, holdfasteners etc and connecting up, including making electric connection from ceiling rose or connector to fan complete all as directed

Taking down carefully existing serviceable exhaust fan, ceiling cable end, etc., removing the fan for keeping in safe custody, fixing the exhaust fan connecting up after rewiring, including making electric connection from ceiling rose/connector to fan complete all as directed

Supply & laying in trenches/drawn through pipes or in road crossing/paths/drains/ducts/floors/along poles/equipments etc., of XLPE insulated, armoured with multistranded aluminium conductor cable conforming to IS-7098 Part-I (1998), heavy duty (LT UG cable) conforming to IS-1554, 1100 Volts grade of size 50 sqmm 3½ core nominal cross sectional area including necessary double compression copper gland and connecting up using suitable size aluminium lugs testing and commissioning complete all as specified and directed NOTE: Excavation, earthwork, brick protection & cable protection etc. will be measured and paid separately under relevant items of this schedule.

Supply and fixing double compression copper gland for fixing armoured cables of size 50 sqmm 3½ core nominal cross sectional area complete all as directed

M&L for distribution board, vertical, made out of sheet metal enclosure (CRCA sheet) dust and vermin proof, double door, VTPN 8 way, 415 volts grade with insulated rated bus bar assembly with isolated neutral bar,door earthing, earth bar IP- 43 protection with poly urithene (PU) gasketing, IK-08 Mechanical impact resistance, door earthing flush to wall, including testing suitable for fixing MCCB, MCB TPN/TP/SPN/SP etc, including taking down existing unserviceable one and removing from site complete all as directed Make: Legrand or equivalent in L&T/ABB/Havells/Siemens/Schneider/Indoasian

S&F in replacement of MCCB triple pole and neutral (four pole) 160 Amp, 415 volts, 50 Hz, having thermal setting range 70% to 100% and adjustable magnetic setting and breaking capacity 25 KA including making incoming and outgoing connections complete all as directed. Make: Legrand or equivalent in L&T/ABB/Havells/Siemens/Schneider/Indoasian

Excavation in trenches ,n.exc 1.5 mtr wide and n.exc 1.5 mtr depth and getting out in hard dense soil for cable/pipe/poles, trimming the sides forming bottom surface to required levels complete all as specified

Reddled earth upto 20cm depth around cable for protection to be filled including spreading, levelling etc & punned down balance quantity shall be returned and filled in including spreading, levelling, watering and well ramming in layers not exceeding 25cm in hard/dense soil all as specified and directed

Removing excavated soil to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.50m above starting point complete all as specified and directed.

Supply and lay bricks, common burnt clay building bricks, sub-class 'B' as directed.

Supply and fix 6 Sqmm aluminium conductor weather proof flat twin core cable with PVC conduit of size 25mm from junction box to security light all as per specification .

Supply and fix in LED street light fitting of 72 W with pressure die cast aluminium housing with polycarbonate cover and high power LEDs and secondary lences with IP 66 protection. 10 KV SPD included. System efficacy 110 lumens /watt. Make: CG cat part No.LST 70 CDL-M or equivalent make aproved by engineer in charge.

Supply and lay XLPE insulated armoured heavy duty electric cable with stranded aluminium conductor 1100 volt grade of cross section area 10 sqmm 2 core laid in trenches along pole/in duct/with wall under road,floor etc complete all as specified and as directed.

Supply and fix steel medium grade GI pipe 40mm bore dia for road crossing/cable protection all as specified.

Supply and fixing in repair SMC terminal box of size 230 x 170 x 105 mm(internal diamensions) made of impact resistance plastic & heat resistant materials including MCB SP 6A with DIN bar and 4 way terminal block, and fixing the box to street light pole made of 25x 3mm flat iron with clamps, nuts and bolts all as specified.

S&F GI bracket with clamp for street light fitting of GI tube 40mm medium grade 1.5m in length bend to shape for fixing LED light including MS flat iron 30x6 mm clamp with suitable two coats of aluminium paint over one coat of primer including preparation of surfaces complete.

Shilpa Engineers and Contractors

DJ GROUP

AKASH CONSTRUCTIONS

KENZ CONSTRUCTIONS

R.K. Builders