TN-05-133-FBDP-25-26

Amount

1. Construction of Anganwadi Building at Samuthirapatti, H/O Samuthirapatti ESTIMATE AMOUNT : RS. 17.25 LAKHS

Earth work excavation for foundation in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by the departmental officers with an initial lead of 10 mts and initial lift of 2 mts. and clearing and levelling the site, etc., complete complying with standard specification.

Earthwork excavation

Supplying and filling in foundation, basement, etc with filling sand in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers.

Cement Concrete 1:4:8 (One Cement, Four M.sand and Ten hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for foundation including dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification

Brick work in Cement Mortar1:5 (one cement and five M.sand) using best quality of country bricks of size 8-3/4" x 4-1/4" x 2-1/4" for foundation and basement including curing, etc., complete complying with standard specifiction.

Refilling with excavated earth other than sand with an initial head load of 100 mts. and depositing the earth as shown by the departmental officers in layers of not more than 15 cm thick well rammed, watered and consolidated etc. complete complying with standard specification

Supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 M height for plane surfaces as detailed below in all floors with all cross bracings using Mild Steel sheets of size 90 x 60 cm and 10 BG stiffened with welded Mild Steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaiton

Below Ground level - Grade beam sides

Below Ground level - Column sides and Above ground level

Supplying, fabricating and placing in position Mild Steel / Ribbed Tor Steel grills for all RCC works as per design given including cost of steel and G.I. binding wire in all floors etc. complete complying with standard specification.

Reinforced Cement Concrete 1:1.5:3 (One Cement, One and a half M.sand and Three hard broken stone jelly) using 20 mm gauge hard broken granite stone jelly for all RCC items of works excluding cost of reinforcement grill and fabricating charges centering and shuttering but including laying, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor / roof slabs wherever necessary etc., complete complying with standard specification and as directed by the departmental officers

Supplying and applying of two coats of putty of 3 mm thick over the exposed RCC surface of ceiling including finishing the joints smoothy with grinding machine and the surface shall be thoroughly cleaned out of dust and scrubbing. The Surface shall then be allowed to dry for atleast 48 hours. Tt shall then be sand papered (waterproof abrasive sheet) to give a smooth and even s urface. Any uneven ness shall be made good by applying 1st coat of putty mixed with water on the entire surface including filling up the undulations and applying 2nd coat 1 of putty alter 6 hours of 1st coat of putty and then sand papering (waterproof a bra sive s heet) th e same arte r it is dry and finishing thc surfa ce sm oot hIy, «tc.,

Plastering with Cement Mortar 1:5 (One cement and Five M.sand), 12mm thick in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers.

Paving the floor with best approved quality fine polished shahabad Stone Slabs of size 600 x 600 of 18 / 20mm thick of Synthetic Grey, Paradise and similar varieties with machine cut edges laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three crushed stone M.Sand) fixing the slabs with required cement slurry and laid in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments etc., The granite stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete as per standard speicification.

Dadooing wall with Glazed tiles of any colour of any size laid in C.M 1:2 mix 20 mm thick & pointing with colour cement using 0.40kg per sq.m including cost & conveyance of all materials to site and all labour charges etc.complete

Paving Floor with scratch proof ceramic tiles of any colour of size 200x200 x 6mm, laid in C.M 1:3 mix 20 mm thick & pointing with colour cement using 0.40kg per sq.m including cost & conveyance of all materials to site and all labour charges etc.complete

Providing granolithic floor finish of the following thickness with plain cement concrete 1:2:4 (One Cement, Two sand and Four aggregate) using 10 to 12mm gauge hard broken stone jelly including laying, finishing and the top rubbed smooth with power trawl, thread lining, curing etc. complete complying with standard specification and as directed by the departmental officers.

Weathering course in brick jelly lime concrete using broken brick jelly of size 20mm uniform gauge in pure slaked lime (no sand to be used) to the proportion of brick jelly to lime being 32:12.5 by volume and laid over the RCC roof slab in a single layer of required slope and finished by beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling lime jaggery water, etc., complete as per standard specification and as directed by the deparmental officers.

Finishing the top of roof with one course of machine pressed tiles of size 200mm x 200mm x 20mm of approved quality set in Cement Mortar 1:3 (One Cement and Three Sand) 12mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers

White washing two coats with freshly burnt white shell lime in all floors including cost of lime, blue powder fevicol type gum, brushes, scaffolding charges, etc., complete complying with standard specification and as directed by the departmental officers.

Supplying and painting the walls with two coats of oil bound distemper over one coat of water based cement primer including cost for distemper, primer, cleaning and scrapping the walls, rendering the walls smooth with necessary putty, brushes, scaffolding arrangements, labour charges, etc., as per standard specification.

Painting two coats of newly plastered wall surface with ready mixed plastic Exterior emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification.

Painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over the existing red oxide priming coat in all floors excluding cost of priming coat etc., complete complying with standard specification.

Painting two coats with Black oxide paint including cost and conveyance of all materials and labour charges etc,complete

Fabrication and supply & Delivery of MILD STEEL DOORS of the following Size with Double Leaf outer frame made of 35x35x5 mm equal M.S.L angle and shutter frame made of 25x25x5mm equal M.S L angle for Horizontal and Vertical members and the shutter frame strengthened by stiffeners of 2 Nos horizontal, 3 Nos. diagonal for each shutter using MS flat of size 20x5mm fully covered with 18 gauge plain M.S full sheet welded with shutter frame neatly and also fixing by welding 6 Nos. of hold fasts made of 35x35x5 mm equal M.S L angle, 2 Nos. of wind appliances, 3 Nos. of tower bolts,1 No aldrop, 3 Nos. of handles fixing the shutter with 6 Nos. of 6 inch hinges with outer frame of the door including painting the whole unit with one coat of best quality of red oxide primer for Anganwadi building.

Steel door D1 of size 0.75 x 1.50m (Single leaf)

Steel door D of size 0.90 x 2.10m (Single leaf)

Steel door D2 of size 1.10 x 2.10m (Single leaf)

Fabrication and supply of MILD STEEL WINDOW of of the following size with Double Leaves outer frame made of 35x35x5 mm equal M.S.L angle, mullion section made of 25x25x5mm equal T section, Shutter Frame made of 25 x 25 x 5mm equal M.S.L angle for Horizontal and Vertical members and the shutter frame strengthened by stiffeners of 2 No. Horizontal for each shutter using 25 x 25 x 5mm equal M.S. T section fully covered with 18 gauge plain M.S full sheet welded with shutter frame neatly and also fixing by welding protective grill with 12mm square M.S rods at an interval of not greater than 10cm centre to centre to the outer frame,4 Nos. of hold fasts made of 35x35x5 mm equal M.S.L angle , 2 Nos. of peg stays with holes for keeping the windows open in different positions, 2 Nos. of locking handles, fixing the shutter with 4 Nos. of 4 inch hinges with outer frame of the window including painting the whole unit with one coat of best quality of red oxide primer for Anganwadi building

Steel window W & W1 of size 1.20m x 1.60m (Double leaf)

Fabrication and supply of N TYPE MILD STEEL GLAZED VENTILATOR (in two parts) of of the following size outer frame made of 25x25x5mm equal M.S.L angle with intermediate rails using 25 x 25 x 5mm equal M.S. T section for panels with 3mm thick pin headed glass with teak wood beading and glass putty and also fixing by welding protective grill with 12mm square M.S rods at an interval of not greater than 10cm centre to centre to the outer frame,4 Nos. of hold fasts connecting the 2 parts at 75mm clear and with 45 degree inclination with 25x25mm 10G weld mesh and wire mesh including painting the whole unit with one coat of best quality of red oxide primer for Anganwadi

Ventilator V1 of size 0.90m x 0.45m

Ventilator V of size 0.60m x 0.45m

Labour charges for fixing of Doors, windows in position including all charges etc.,complete

Supplying and fixing in position by means of 75mm long and 6.5mm dia counter sunk bolts and nuts embedded in the floor with rubber or fibre washers. Best quality and approved make white glazed earthern ware European water closet with P or S trap with seat and double flapped rigid PVC seat cover with chromium plated hinges, and giving necessary connection to PVC socket using 110 mm dia PVC pipe 6 kg/sqcm.of 0.60m length including supplying and fixing PVC tank of 10.00 litre capacity with all internal fittings with a pair of cast iron brackets and with all fittings such as 15mm dia nylon connection, 15mm dia GM wheel value, 15mm dia brass nipple including, labour charges for fixing the flushing tank on wall with teak wood plugs and screws, giving water supply connection, painting CI brackets with two coats of best approved quality synthetic enamel paint over a coat of red oxide primer, redoing the disturbed masonry and flooring to original condition, etc. complete complying with standard specification.

Supply and fixing of Baby Pan including cost and conveyance and all labour charges for fixing etc.,complete

Supply and Fixing of Cuddapah slab of 20/30mm thick for Shelf arrangements including cost and conveyace of all materials to site and all labour charges etc complete

Supplying and fixing of 110mm dia PVC pipe in position best approved of BIS quality PVC rain water down fall pipes having a pressure of 4 kg. / sq.cm including cost of necessry PVC shoe, PVC bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the RCC roof slab including finishing neatly etc., complete. The rate shall be inclusive of cast of removable cast iron grating. The PVC pipe shall be fixed in wall with special type of "U" clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification.

Electrification

Wiring with 2 x 1.5 sq.m (22/0.3) PVC insulated unsheathed SC Cu. Conductor of 1100V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories with TW switch box in flush with wall covered with hylum sheet of 3mm thick with painting of suitable colour for open PVC light point/fan point(for electronic regulator) - S.D.No: 25

Wiring with 2 x 1.5 sq.m (22/0.3) PVC insulated unsheathed SC Cu. Conductor of 1100V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories and with 150 x 100 x 113 TW switch box for 5A 3pin non inter locking CS plug with painting of suitable colour with continuos earth wire connection of 14 SWG TC wire for open PVC plug - S.D.No: 38

Supply and fixing of 1200mm (48") AC ceiling fan with stepped electronic 300 W regulator with 1 meter down rod on the existing clamp. - S.D.no: 106

Supply and fixing of AC Exhaust fan 300mm sweep (light duty) etc.,complete without provision of hole in the wall-S.D.No:115

Supply and run of 2 of 1.50 sq.mm (22/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100 V on 7/20 GI bearer wire for service connection mains. - S.D.No: 64

Supply and fixing of single box type 4'40 W flu fitting complete with copper choke and condensor with TW round blocks on wall or ceiling with flu tube with PVC unsheathed copper leads from terminals to the fitting - S.D.No: 88

Supply and Fixing of CFL bulb 11w including cost and conveyance of all materials and labour charges etc complete. SD 81

Supply and fixing of 16 Amps DPIC Switch of 500V with fuse and neutral (Side Handle) on suitable TW Board, with earth connection only. - S.D.No: 142

Supply and fixing of TNEB meter Board suitable for 32A Single phase service connection with 32A fuse unit(500V) 32A neutral link and earth link (1"x1/8" Copper flat) on TW plank of size 375mmx300mmx19mm with supporting TW reepers of 1" thick an either side with painting with suitable bolt and nuts for fixing the TW plank on wall with earth connection and inter connection with 7/20 PVC insulated copper wire from EB meter to fuse unit - SD No: 124

EB Deposit amount

Provision for Water supply arrangements etc.,

Supply and fixing of 1000 litre HDPE tank

32mm dia PVC pipe 10KSC

32mm dia PVC Coupler

32mm dia PVC elbow

32mm dia PVC Tee

32mm dia PVC Ball valve

63mm PVC Pipe

20mm dia PVC screw down tap heavy type

Earth work excavation in hard stiff clay and hard rock earth and lowering and laying, Jointing of pipes and refilling the trench with excavation soils, well rammed and consolidated after the pipes and specials are laid, jointed and tests including all labour charges etc.,complete

Provision for Sanitary pipe line arrangements including all charges etc.,complete

110mm dia PVC pipe 4kg/sqm

110mm dia PVC elbow

Supplying and fixing in position CI manhole covers with CI frames (Heavy duty) of size 60cm x 60cm of best approved quality as per standard specification etc., complete compying with standard specifications

Provision for Rain water Harvesting structure including cost and conveyance of all materials and all labour charges etc.,complete

Provision for Septic tank arrangements

Provision for Name Board painting and Wall cartoons painting including cost and conveyance of all materials and all labour charges etc.,complete

GST Amount for providing Service to Government Contract Works for the above Construction Works. { GST Amount is the Total GST Amount for total overall quoted amount above this row in column "BB" for all works in this package}

Om Muruga Builders (BID ID -1552206)