EXECUTION OF THE WORK UNDER THE WORK REPAIR AND UPGRADATION OF TOILET BLOCK INSIDE PURANA QILA COMPLEX NEW DLEHI

Dismantling of flushing cistern of all types (C.I./PVC/Vitrious China) including stacking of useful materials near the site and disposal of unserviceable materials within 50 metres lead.

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead : Of area 3 sq. metres and below [EACH]

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead. For thickness of tiles 10 mm to 25 mm

Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. In cement mortar [

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge. All kinds of soil

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) [M3]

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete. Size of Tile 600x600 mm

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:4 (1 cement : 4 coarse sand)

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately). Sal wood [M3]

Providing and fixing in wall lining flat pressed three layer (medium density) particle board or graded wood Pre- laminated one side decorative lamination and other side balancing lamination Grade I, Type II, IS : 12823 marked, including priming coat on unexposed arrangement and screws etc. complete :25 mm thick

CEMENT PLASTER (IN COARSE SAND) 12 mm cement plaster of mix : 1:4 (1 cement: 4 coarse sand)

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-inCharge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade : Two or more coats on new work

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. completeat all levels. 8.2.2 Granite stone slab colour black, Cherry/Ruby red 8 Area of slab over 0.50 sqm

Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. 8.3.2 Granite work

Modular Design Toilet Block cabins:- Materials - Compact grade Laminate Board, Accessories - made of corrosion and scratch resistance high quality brushed finish stainless steel. Accessories Will be hygienic and antistatic having high resistance to weathering. Accessories will be resistant to corrosion and pollution, domestic clearners, disinfectans and diluted acids. Head Rail- Made of corrosion resisance Aluminium oxide extruded profile. Other Accessories:- (i) spring loaded door hings( self closing) (ii) Privacy lock with indicator. (iii) Coat hanger (iv) Adjustable legs (v) Door knobs. Dimensions Total cubide height from ground-1970 MM, Cubicle depth-1500 MM, Pilaster Height-1860 MM, Door Height-1800 MM, Partition Width-1000 MM, Door Width- 600 MM (including all fittings)"

Provision for providing and fixing of electrical articals for providing electricity in house` 1.5 Sqmm copper wire (Havells or eq) [bundle]

2.5 Sqmm copper wire (Havells or eq) [bundle]

LED batten tube light 4 feet (Havells or eq) [EACH]

LED batten mirror light 2 feet (Havells or eq) [EACH]

Exhaust fan 15 inch (silent) (Havells or eq) [EACH]

Batten 1 inch [EACH]

Gypsom pech 1 inch [EACH]

4x4 inch square box (Havells or eq) [EACH]

Sealing roj [EACH]

Gitti 1.5 inch [EACH]

PVC tape box [EACH]

Ceiling fan 48 inch (Havells or eq) [EACH]

2x2 feet LED light ceiling (Havells or eq) [EACH]

6 Amp Switch plain [EACH]

6 Amp socket plain [EACH]

16 Amp Switch plain [EACH]

16 Amp socket plain [EACH]

12 modular Box [EACH]

12 Modular plate [EACH]

6 modular box [EACH]

6 modular plate [EACH]

10 Amp Switch [EACH]

20 Amp socket [EACH]

20 Amp switch [EACH]

Wall fan silent [EACH]

4 core aluminium armound wire cable 25 Sqmm (Havells or eq) [RMT]

Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required : 17.5.1 Single half stall urinal with 5 litre P.V.C. automatic flushing cistern

Provision of providing and fixing of European (W.C) of wall hanging/mounted including all fitting i.e connection pipes. sockets & other fittings to connect the tap and drain out pipe & holes including all type of washer, nut bolts etc complete. (Jaquar, Hindware, Parryware or eq) Jaquar OPS-WHT-15953BIUFPM, CNC-WHT-959NUF, CNC-WHT- 961NUF)(Any of the mentioned code of related article will be consider for execution after the approval from the competant authority and the same will be executed acoording to the finalized code & rate of the article. As the rates are taken according to the mentioned codes)

Polyethylene water storage tank with cover and suitable locking arrangement

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. 17.28.2 Flexible pipe 17.28.2.2 40 mm dia

Providing and fixing beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick

Provision of providing and fixing of washbasin including all fitting i.e connection pipes. sockets & other fittings to connect the tap and drain out pipe & holes including all type of washer, nut bolts etc complete. (Jaquar, Hindware, Parryware or eq) Jaquar FUS-2931, CNS- WHT-705, OPS-WHT-15801 PM, OPS-WHT- 15601 PM, GDS-WHT-25901)(Any of the mentioned code of related article will be consider for execution after the approval from the competant authority and the same will be executed acoording to the finalized code & rate of the article. As the rates are taken according to the mentioned codes)

Providing and fixingToilet jet/Hand Shower(Jaquar or eq) in toilet blocks for all fitting including material & labour charges etc complete.(Any of the mentioned code of related article will be consider for execution after the approval from the competant authority and the same will be executed acoording to the finalized code & rate of the article. As the rates are taken according to the mentioned codes) and make as approved by Engineer - in - charge.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. 18.7.6 50 mm nominal dia Pipes [

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. 25 mm nominal dia Pipes

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. 15 mm nominal bore

2.25 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :4.1.4 1:2:4 (1 Cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 40 mm nominal size derived from natural sources)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: 6.1.1 Cement mortar 1:4 (1 cement : 4 coarse sand)

Centering and shuttering including strutting, propping etc. and removal of form for:5.9.5 Lintels, beams, plinth beams, girders, bressumers and cantilevers

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level : Mild steel and Medium Tensile steel bars

"9.32 Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brickhoney comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. 19.32.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5"

19.18 Supplying and fixing C.I. cover without frame for manholes :

19.15 Providing M.S. foot rests including fixing in manholes with 20x20x10 cm cement concrete blocks 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) as per standard design :19.15.1 With 20x20 mm square bar

Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge.

Providing and fixing PVC pipe 8 to 12 mm thick for waste connection pipe garbage from toilet towards main hole towards septic tank and others as per requirement at site etc complete.

Provision for re installation of wooden flooring after dismantling from Museum Gallery B and re install to HA office including self levelling adhsive & matting below the floor and all other charges etc complete.

Cleaning of sewer line with jet pressure including repair of main hole and replacement of main hole cover including providing and fixing senitory pipe wherever necessary

Providing and fixing kitchen sink with C.I. brackets, C.P. brass chain with rubber plug, 40 mm C.P. brass waste complete, including painting the fittings and brackets, cutting and making good the walls wherever required: 17.9.1 White glazed fire clay kitchen sink of size 600x450x 250 mm

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: 17.1.1 White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests

Providing and Fixing 15 mm thick densified tegular edged eco friendly light weight calcium silicate false ceiling tiles of approved texture of size 595 x 595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanised steel sections (galvanising @ 120 grams per sqm including both side) consisting of main ‘T’ runner suitably spaced at joints to get required length and of size 24x38 mm made from 0.33 mm thick (minimum) sheet, spaced 1200 mm centre to centre, and cross “T” of size 24x28 mm made out of 0.33 mm (Minimum) sheet, 1200 mm long spaced between main’T’ at 600 mm centre to centre to form a grid of 1200x600 mm and secondary cross ‘T’ of length 600 mm and size 24 x28 mm made of 0.33 mm thick (Minimum) sheet to be inter locked at middle of the 1200x 600 mm panel to from grid of size 600x600 mm, resting on periphery walls /partitions on a Perimeter wall angle pre- coated steel of size(24x24X3000 mm made of 0.40 mm thick (minimum) sheet with the help of rawl plugs at 450 mm centre to centre with 25 mm long dry wall screws @ 230 mm interval and laying 15 mm thick densified edges calicum silicate ceiling tiles of approved texture in the grid, including, cutting/ making opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc., wherever required. Main ‘T’ runners to be suspended from ceiling using G.I. slotted cleats of size 25x35x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm G.I. adjustable rods with galvanised steel level clips of size 85 x 30 x 0.8 mm, spaced at 1200 mm centre to centre along main ‘T’, bottom exposed with 24 mm of all Tsections shall be pre- painted with polyster baked paint, for all heights, as per specifications, drawings and as directed by Engineer-in- Charge."

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.

Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gram/litre, of approved manufacturer and of required shade and colour all complete to achieve even shade and colour : 13.41.1 New work (two or more coats) over and including water thinnable priming coat with cement primer having VOC content less than 50 gram/litre

Providing and fixing factory made Kitchen Cabinet Shutter/Partition 20 mm nominal thickness of approved shade, quality and make, made from rigid foam sheets (Single extruded) having density 600 Kg/cum and laminated on both side by laminate Sheet/PVC foil lamination. The exposed edges shall be sealed with PVC edge beading of same shade and colour. The shutter shall be fire retardent having necessary screw holding capacity. Shutter shall be fixed to frame using approved hinges with necessary stainless steel screws, all complete as per direction of Engineer-in-charge.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. 10.16.1 Hot finished welded type tubes

Providing fixing of aluminium composite panel in metalic colour of approved shades made out of 4mm thick aluminium composite panel material consisting of 3mm thick FR grade mineral core sandwiched between two Aluminium sheets (each 0.5mm thick). The aluminium composite panel cladding sheet shall be coil coated, with Kynar 500 based PVDF / Lumiflon based fluoropolymer resin coating of approved colour and shade on face # 1 and polymer (Service) coating on face # 2 as specified using stainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backer rods etc.on both sides fixed on M.S. structure with cutting, fitting etc. complete, for inside paneling

Providing and fixing waterproffing flex over the aluminium composite panel for cover area with cutting, pasting etc including all labour & material charges etc complete.

Disposal of building rubish/malba/ similar unservisable, dismentaleted or waste materials by mechanical menas uncluding loading, transporting , unloading to dumping ground or as approved by Engineer-in charge beyond 50m intial lead for all leads including all lifts involved lead 10 to 20 km aprox

Stone tile work for wall lining upto 10 m height with special adhesive over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand), including pointing in white cement with an admixture of pigment to match the stone shade. 7.38.1 8 mm thick (mirror polished and machine cut edge) 7.38.1.1 Granite stone of any colour and shade

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. 11.56.1 Polished Granite stone slab of colour Black, Cherry/Ruby Red or equivalent

Providing and installation of 14 gauge dual drinking water fountain with back plate and chiller ,polished , crome plated brass bubbler, push buttom amf waste strained (HAWS model no H117 / or equavelant)

Providing and fixing of FRP Body RO Plants 150ltr per hr system with all fiting etc complete. Purification Plants Should have Reverse Osmosis Automation Grade Semi- Automatic Voltage 220-380 V Frequency 50-60 HzRO Capacity 150 LPH etc complete

Providng and fixing1 hp booster pressure pump with 20ltr water tank including all necessary fitings etc complete (crompton or equavelent).

Provision of providing and connection of inlet from nearest source and out let pipes from building to the nearest mainhole including excation trench , laying of pipe , and all connection etc complete UPVC pipe 25mm (10ft) (Astral/Supreme or eq)

UPVC elbow 25mm (Astral/Supreme or eq)

UPVC Tee 25mm(Astral/Supreme or eq

Tank nipple 25mm (Astral/Supreme or eq)

M Tee 25x25

UPVC pipe 20mm (10ft)

UPVC elbow 20mm

UPVC Tee 20mm

B. Elbow 20X15mm

M Tee 20x15mm

PVC pipe 110mm dia (6mtr)

PVC Y Tee 110mm

45 degree angle elbow

Ball valve 25mm

Ball valve 20mm

PVC pipe 50mm dia (10ft)

PVC Elbow 50mm dia

PVC F Tee 50mm

PVC Tee 50mm

Providing and placing on terrace (at all floor levels Tripple layer) polyethylene water storage 500lt capacity tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. )(Sintex, Aquasafe or eq)

Provision for three layer 250 ltr loft water tanks (heavy duty) for storage of clean water with cover and sutable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Electric job complete with all necessary PVC insulated copper wire, switch board, Switches, soket and all other fixtures etc complete. Sitc of MCB box with all necessary MCBs complete work.

Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) upto plinth level with : 7.1.1 Cement mortar 1:6 (1 cement : 6 coarse sand)

Random rubble masonry with hard stone in superstructure above plinth level and upto floor five level, including leveling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) at window sills, ceiling level and the like. 7.2.1 Cement mortar 1:6 (1 cement : 6 coarse sand)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 4.1.2 1:1½:3 (1 Cement: 1½ coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)

Painting with synthetic enamel paint of approved brand and manufacture of required shade and color to give an even shade two or more coat including scraping of old paint by using sand papering & cleaning the surface smooth for paint work complete

Pointing on stone work with cement mortar 1:3 (1 cement : 3 fine sand) :13.33.2 Raised and cut pointing

Provision for providing and fixing of xpm wire mass jaali to protect for birds & insects dont enter inside the area of Drinking Water & other places etc complete.

Providing corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 12.1.1 1.00 mm thick with zinc coating not less than 275 gm/m²

Please Enable Macros to View BoQ information