8949 REPAIR TO CERTAIN WOODEN/STEEL FURNITURE, POLISHING, PAINTING AND OTHER RELATED WORK AT DGQA COMPLEX UNDER GE NORTH MUMBAI

Amount

SOFA SET WOODEN 5 SEATER ( 3+1+1) FD-258, FD-373 Removing the existing unserviceable foam replacing with new foam 40 density 100mm thick covered with long cloth complete all as specified in drawing and directed by Engineer-in-Charge. Note : tapestry cloth will be measured and paid on relevalent item

SOFA SET WOODEN 5 SEATER ( 3+1+1) FD-258,FD-373 Removing the existing unserviceable tapestry cloth of seat cushion replacing with new tapestry cloth of approved quality not less than Rs.340/- per metre complete all as specified in drawing and directed by Engineer-in-Charge.

SOFA SET WOODEN 5 SEATER ( 3+1+1) FD-258,FD-373 Removing the existing unserviceable arm rest and replacing with new teakwood of section 70 x 35mm duly furnished and polished complete all as specified in drawing and directed by Engineer-in-Charge.

SOFA SET WOODEN 5 SEATER ( 3+1+1) FD-258,FD-373 Removing the existing unserviceable seat ply for single seater and replacing with 12mm thick BWR Phenol bonded plywood complete all as specified in drawing and directed by Engineer-in-Charge.

SOFA SET WOODEN 5 SEATER ( 3+1+1) FD-258,FD-373 S & F in repairs new PVC ring/rubber shoes to the legs duly screwed complete all as specified in drawing and directed by Engineer-in-Charge.

SOFA SET WOODEN 5 SEATER ( 3+1+1) FD-258,FD-373 Preparing/cleaning of old decorated surface/rubbing by emery paper removing all spots, filling with putty and polishing with two coats of French polish match to match existing polish complete all as specified in drawing and directed by Engineer-in-Charge.

CHAIR DINING FD-228 Removing the existing unserviceable Plastic cane from seat and replacing with best quality of white plastic cane 2mm wide and 0.4mm thick half round gola type, without any joint, in Godrej pattern complete all as specified in drawing and directed by Engineer-in-Charge.

CHAIR DINING FD-228 Removing the existing unserviceable front leg and replacing with new teakwood legs of section 45 x 45mm duly furnished and polished complete all as specified in drawing and directed by Engineer-in-Charge.

CHAIR DINING FD-228 Removing the existing unserviceable rear leg and replacing with new teakwood legs of section 65 x 45mm duly furnished and polished complete all as specified in drawing and directed by Engineer-in-Charge.

CHAIR DINING FD-228 Removing the existing unserviceable upper/lower stiffener for back and replacing with new one teakwood section 45 x 15mm out of 45 x 35mm duly furnished and polished complete all as specified in drawing and directed by Engineer-in-Charge.

CHAIR DINING FD-228 Removing the existing unserviceable centre stiffener for bottom legs and replacing with new one teakwood section 25 x 20mm duly furnished and polished complete all as specified in drawing and directed by Engineer-in-Charge.

CHAIR DINING FD-228 Removing the existing unserviceable side stiffener for bottom legs and replacing with new one teakwood section 25 x 20mm duly furnished and polished complete all as specified in drawing and directed by Engineer-in-Charge.

CHAIR DINING FD-228 Removing the existing unserviceable PVC ring/ rubber shoe and replacing with new one complete all as specified in drawing and directed by Engineer-in-Charge.

CHAIR DINING FD-228 Preparing/cleaning of old decorated surface/rubbing by emery paper removing all spots, filling with putty, two coats of French polish match with existing polish complete all as specified in drawing and directed by Engineer-in-Charge.

PEG TABLE FD-25 Removing the existing unserviceable top and replacing with 19mm MDF board with 4mm thick teakwood edging complete all as specified in drawing and directed by Engineer-in-Charge.

PEG TABLE FD-25 Removing the existing unserviceable leg and replacing with new teakwood legs of section 30 x 50mm duly furnished and polished complete all as specified in drawing and directed by Engineer-in-Charge.

PEG TABLE FD-25 Removing the existing unserviceable front rail and replacing with new teakwood rail of section 20 x 40mm duly furnished and polished complete all as specified in drawing and directed by Engineer-in-Charge.

PEG TABLE FD-25 Removing the existing unserviceable short stiffener and replacing with new teakwood stiffener of section 20 x 40mm duly furnished and polished complete all as specified in drawing and directed by Engineer-in-Charge.

PEG TABLE FD-25 Removing the existing unserviceable PVC ring/ hard rubber shoe and replacing with new one complete all as specified in drawing and directed by Engineer-in-Charge.

PEG TABLE FD-25 Preparing/ cleaning of old decorated surface/ rubbing by emery paper removing all spots, filling with putty, two coats of French polish match with existing polish complete all as specified in drawing and directed by Engineer-in-Charge.

HAT STAND WITH MIRROR FD-233/FD-23 Removing the existing unserviceable mirror and replacing with new mirror, 5.5mm thick electro copper plated mirror of polished sheet with 6mm x 35mm TW edging complete all as specified in drawing and directed by Engineer-in-Charge.

HAT STAND WITH MIRROR FD-233/FD-23 Removing the existing unserviceable peg and replacing with copper oxidised steel peg complete all as specified in drawing and directed by Engineer-in-Charge.

HAT STAND WITH MIRROR FD-233/FD-23 Removing the existing unserviceable key plate and replacing made out of 3mm thick MS plate of size 40 x 25mm complete all as specified in drawing and directed by Engineer-in-Charge.

HAT STAND WITH MIRROR FD-233/FD-23 Preparing/cleaning of old decorated surface/rubbing by emery paper removing all spots, filling with putty and polishing with two coats of French polish match to match existing polish complete all as specified in drawing and directed by Engineer-in-Charge.

BED CHARPOY WOODEN DRG NO : FD-21/FD-246 Removing the existing unserviceable top and replacing with 12mm thick commercial plywood ISI marked size exact as mentioned in drawing, complete all as specified in drawing and directed by Engineer-in-Charge.

BED CHARPOY WOODEN DRG NO : FD-21/FD-246 Removing the existing unserviceable short rail and replacing with new teakwood side rail size and length as indicated in drawing, complete all as specified in drawing and directed by Engineer-in-Charge.

BED CHARPOY WOODEN DRG NO : FD-21/FD-246 Removing the existing unserviceable long rail and replacing with new teakwood long rail size and length as indicated in drawing complete all as specified in drawing.

BED WITH PLY WOOD DRG NO : FD-21/FD-246 Removing the existing unserviceable head rest with legs and replacing with new head board including legs with 3.5/4.0mm thick teak ply face both sides, including 12 dia half cut teak wood bead complete all as specified in drawing and directed by Engineer-in-Charge.

BED CHARPOY WOODEN DRG NO : FD-21/FD-246replacing with foot board including legs with 3.5/4.0mm thick teak ply face both sides, including 12 dia half cut teak wood bead complete all as specified in drawing and directed by Engineer-in-Charge.

BED CHARPOY WOODEN DRG NO : FD-21/FD-246 Removing the existing unserviceable Centre stiffener and replacing with new one to support bed top plywood complete all as specified in drawing and directed by Engineer-in-Charge.

BED CHARPOY WOODEN DRG NO : FD-21/FD-246 Removing the existing unserviceable Corner block rail and replacing with new one of size 50 x 100 x 100 mm between rail and legs for tightening of bed complete all as specified in drawing and directed by Engineer-in-Charge.

BED CHARPOY WOODEN DRG NO : FD-246 Preparing/cleaning of old decorated surface/rubbing by emery paper removing all spots, filling with putty, two coats of French polish match with existing polish complete all as specified in drawing and directed by Engineer-in-Charge.

TABLE CENTRE FD-235 Removing the existing unserviceable top and replacing with 19mm MDF board with 4mm thick teakwood edging complete all as specified in drawing and directed by Engineer-in-Charge.

TABLE CENTRE FD-235 Removing the existing unserviceable top long rail and replacing with new teakwood rail of section 25 x 50mm thick duly furnished and polished complete all as specified in drawing and directed by Engineer-in-Charge.

TABLE CENTRE FD-235 Removing the existing unserviceable top short rail and replacing with new teakwood rail of section 25 x 50mm thick duly furnished and polished complete all as specified in drawing and directed by Engineer-in-Charge.

TABLE CENTRE FD-235 Removing the existing unserviceable legs and replacing with new teakwood legs of section 45 x 45mm at top and 25 x25mm at bottom duly furnished and polished complete all as specified in drawing and directed by Engineer-in-Charge.

TABLE CENTRE FD-235 Removing the existing unserviceable PVC ring/ rubber shoe and replacing with new one complete all as specified in drawing and directed by Engineer-in-Charge.

TABLE CENTRE FD-235 Preparing/cleaning of old decorated surface/rubbing by emery paper removing all spots, filling with putty, two coats of French polish match with existing polish complete all as specified in drawing and directed by Engineer-in-Charge.

TABLE WRITING FD-275 Removing the existing unserviceable top and replacing with 19mm MDF board with 4mm thick teakwood edging complete all as specified in drawing and directed by Engineer-in-Charge.

TABLE WRITING FD-275 Removing the existing unserviceable legs and replacing with new teakwood legs of section 60 x 60mm at top and 30 x 30mm at bottom duly furnished and polished complete all as specified in drawing and directed by Engineer-in-Charge.

TABLE WRITING FD-275 Removing the existing unserviceable drawer and replace with new drawer drawer made out of 19mm commercial Ply BWR both side commercial finish provided with 3mmthick teak wood beading all around complete all as specified and directed by Enge-in- charge.

TABLE WRITING FD-275 Removing the existing unserviceable Shutter and replace with new drawer shutter made out of 19mm commercial Ply BWR both side commercial finish provided with 3mmthick teak wood beading all around complete all as specified and directed by Enge-in- charge.

TABLE WRITING FD-275 Removing the existing unserviceable rail and replace with new rail made IInd class hard teakwood all as specified and directed by Enge-in- charge.

TABLE WRITING FD-275 Removing the existing unserviceable PVC rubber shoe and replacing with new one complete all as specified in drawing and directed by Engineer-in-Charge.

TABLE Writing FD-275 Preparing/cleaning of old decorated surface/rubbing by emery paper removing all spots, filling with putty, two coats of French polish match with existing polish complete all as specified in drawing and directed by Engineer-in-Charge.

TABLE DINING 8 PER FD-273/FD-30 Preparing/cleaning of old decorated surface/rubbing by emery paper removing all spots, filling with putty,two coats of French polish match with existing polish complete all as specified in drawing and directed by Engineer-in-Charge.

ALMIRAH LARGE STEEL- FD-1031 Removing of unserviceable handle of any description and supplying and fixing chromium plated handle of size 150mm long to almirah large steel complete all as specified and as directed by Engineer-in-Charge. Make Godrej or equivalent to Godrej pattern

ALMIRAH LARGE STEEL- FD-1031 Removal of unserviceable locks of any description and supplying and fixing locks of grade- II quality and shall conform to IS: 729-1979, 6 lever brass (50mmx50mm) Godrej pattern to almirah large steel with duplicate stainless steel keys complete all as specified and as directed by Engineer-in-Charge. Make - Godrej or equivalent to Godrej pattern

ALMIRAH LARGE STEEL- FD-1031 Removing of unserviceable cleats and supplying and fixing new cleats using with 1.6mm thick MS sheet to shelves of almirah large steel complete all as specified and as directed by Engineer-in-Charge.

ALMIRAH LARGE STEEL- FD-67/FD-1031 M & L for removing old unserviceable hinges 75mm from almirah large steel and supply & fix new hinges 75mm same as per existing size and material by welding complete all as specified and as directed by Engineer-in-Charge.

ALMIRAH LARGE STEEL- FD-67/FD-1031 Removing old unserviceable legs and supplying and fixing new legs of size 100mm x 485mm x 75mm made out of 1mm thick CRCA steel and welding to almirah large steel complete all as specified and as directed by Engineer-in-Charge.

ALMIRAH LARGE STEEL- FD-67/FD-1031 Removing old unserviceable locking vertical rod and supplying and fixing new locking vertical rod of 10mm MS rod to almirah large steel complete all as specified and as directed by Engineer-in-Charge.

ALMIRAH LARGE STEEL- FD-1031 Removing of unserviceable shelves from Almirah large and supplying and fixing new shelves to almirah large steel with 1mm thick CRCA steel shelves complete all as specified and as directed by Engineer-in-Charge.

ALMIRAH LARGE STEEL-FD-1031 Removing old unserviceable shutter and supplying and fixing new shutter made out of 1mm thick CRCA steel and fixed to almirah large steel with and including hinges complete all as specified and as directed by Engineer-in-Charge.

ALMIRAH LARGE STEEL- FD-1031 M & L for preparing the surface of almirah large steel with shelves by scrapping with emery paper, filling holes with putty wherever required and painting both internally and externally with two coats of olive green synthetic enamel paint complete all as specified and as directed by Engineer-in-Charge.

ALMIRAH MEDIUM/SMALL STEEL- FD-1032 Removing of unserviceable handle of any description and supplying and fixing chromium plated handle of size 150mm long to almirah medium/small steel complete all as specified and as directed by Engineer-in-Charge. Make Godrej or equivalent to Godrej pattern

ALMIRAH MEDIUM/SMALL STEEL-FD-1032 M & L for removing old unserviceable 3 way locking device from almirah medium/small steel and supply & fix lock 6 lever 50x50mm device operated by means of a chromium plated steel handle same as per existing size and material complete all as specified and as directed by Engineer-in-Charge. Make Godrej or equivalent to Godrej pattern

ALMIRAH MEDIUM/SMALL STEEL- FD-1032 Removing of unserviceable cleats and supplying and fixing new cleats using with 1.6mm thick MS sheet to shelves of almirah medium/small steel complete all as specified and as directed by Engineer-in-Charge.

ALMIRAH MEDIUM/SMALL STEEL- FD-1032 M & L for removing old unserviceable hinges 75mm from almirah medium/small steel and supply & fix new hinges 75mm same as per existing size and material by welding complete all as specified and as directed by Engineer-in-Charge.

ALMIRAH MEDIUM/SMALL STEEL- FD-1032 Removing old unserviceable legs and supplying and fixing new legs of size 100mmx 400mm x 75mm made out of 20 Gauge MS sheet and welding to almirah medium and small steel complete all as specified and as directed by Engineer-in-Charge.

ALMIRAH MEDIUM/SMALL STEEL- FD-1032 Removing of unserviceable shelves from Almirah medium and supplying and fixing new shelves to almirah medium and small steel with 1mm thick CRCA steel shelves complete all as specified and as directed by Engineer-in-Charge.

ALMIRAH MEDIUM/SMALL STEEL- FD-67/FD-1032 M & L for preparing the surface of almirah medium/small with shelves by scrapping with emery paper, filling holes with putty wherever required and painting both internally and externally with two coats of synthetic enamel olive green paint of approved shade complete all as specified and as directed by Engineer-in-Charge.

CHAIR CBA STEEL FD-75(M) SIMILAR PATTRN Removing the unserviceable Seat and S & F new seat of teak wood adjusting size duly 4mm plastic caned closely knitting and polished with nut and bolt complete all as specified and directed by Engineer-in -charge.

CHAIR CBA STEEL FD-75(M) SIMILAR PATTRN Removing the unserviceable back and S & F new back of teak wood adjusting size duly 2mm and around lining 4mm plastic caned closely knitting and polished with nut and bolt complete all as specified and directed by Engineer-in -charge.

CHAIR CBA STEEL FD-75(M) SIMILAR PATTRN Removing the existing unserviceable left/right armrest and replacing with new one teakwood section 60 x 25mm duly furnished and polished complete all as specified in drawing and directed by Engineer-in-Charge.

CHAIR CBA STEEL FD-75(M) SIMILAR PATTRN Removing old unserviceable PVC ring/ rubber and supplying and fixing new PVC ring/ rubbers complete all as specified and as directed by Engineer-in-Charge.

CHAIR CBA STEEL FD-75(M) SIMILAR PATTRN M & L for preparing the surface of chair CBA steel by scrapping with emery paper, filling holes with putty wherever required and painting with two coats of synthetic enamel paint olive green complete all as specified and as directed by Engineer-in-Charge.

CHAIR COMPUTER/REVOLVING- TP SIMILAR PATTERN Removing old unserviceable gas lift from all type of chair revolving and S & F new gas lift of chrome free cylinder tube fixed in MS black powder coated outer central column tube 38mm dia and 2mm thick with 100mm stroke length and able to sustain gas pressure of 300 force complete all as specified and as directed by Engineer-in-Charge.

CHAIR COMPUTER/REVOLVING- TP SIMILAR PATTERN Removing old unserviceable seat from all type of chair revolving and S & F new seat of 12mm thick hot pressed plywood upholstered with polypropylene fabric and moulded polyurethene foam with PVC lipping all round complete all as specified and as directed by Engineer-in-Charge.

CHAIR COMPUTER/REVOLVING- TP SIMILAR PATTERN Removing old unserviceable back from all type of chair revolving and S & F new back of 12mm thick hot pressed plywood upholstered with polypropylene fabric and moulded polyurethene foam designed with contour lumber support for extra confortwith PVC lipping all round complete all as specified and as directed by Engineer-in-Charge.

CHAIR COMPUTER/REVOLVING- TP SIMILAR PATTERN Removing old unserviceable castor wheels of chair revolving and S & F new twin wheel castors of injection moulded in black nylon complete all as specified and as directed by Engineer-in-Charge.

CHAIR COMPUTER/REVOLVING- TP SIMILAR PATTERN Removing old unserviceable polyurethene PVC arms rest of chair revolving and S & F new polyurethene PVC arms rest made out of black integral skin polyurethane reinforced with MS insert scratch and weather resistant 50-70 shore "A‟ Hardness, fitted to the seat with powder coated armrest brackets made of 5mm thick HR steel all as specified and as directed by Engineer-in-charge.

CHAIR COMPUTER/REVOLVING- TP SIMILAR PATTERN Removing old unserviceable 5 star base of chair revolving and S & F new pedestal assembly injection moulded in black 30% glass filled nylon 10.5mm dia forged bright zinc coated MS castor pin, press fitted each prong for holding castor & 600mm pitch centre dia all as specified and as directed by Engineer-in-charge. Note- Castor wheel shall be measured and paid separately.

TABLE OFFICE OFFICERS STEEL FD-84, FD-1003 Removing of existing broken table top of table office officer steel and supplying and fixing new table top of size 1.68m x 0.87m of 18mm thick MDF board with 3m thick TW edging including polishing to teakwood beading complete all as specified and as directed by Engineer-in-Charge.

TABLE OFFICE OFFICERS STEEL FD-84, FD-1003 Taking out worn out Legs of table office officer without damaging the other components and supplying and fixing the new Legs made out of 25mm square mild steel tubing of 16 gauge and fixing the same by welding to the table in place of removed Legs complete all as specified and as directed by Engineer-in-Charge.

TABLE OFFICE OFFICERS STEEL FD-84, FD-1003 Taking out worn out stiffener of table office officer without damaging the other components and supplying and fixing the new stiffener made out of 25mm square mild steel tubing of 16 gauge and fixing the same by welding to the table in place of removed stiffener complete all as specified and as directed by Engineer-in-Charge.

TABLE OFFICE OFFICERS STEEL FD-84, FD-1003 Removing of unserviceable drawer including drawer box (set of three drawer) of table office officer steel and S & F new drawer with box (Set of Three)boxes of existing size, made out of 1mm thick MS sheet with side channels ,back springs complete all as specified and as directed by Engineer-in-Charge.

TABLE OFFICE OFFICERS STEEL FD-84, FD-1003 Removing of unserviceable lock of any description and supplying and fixing new locks of grade- II quality and shall conform to IS: 729-1979, with brass 4 lever with duplicate keys as Godrej pattern to table office officer complete all as specified and as directed by Engineer-in-Charge. Make : Godrej or equivalent to godrej make

TABLE OFFICE OFFICERS STEEL FD-84, FD-1003 Removing old unserviceable PVC ring/ rubber of table office officer and supplying and fixing new PVC ring/ rubbers outer suitable for 25mm MS tube complete all as specified and as directed by Engineer-in-Charge.

TABLE OFFICE OFFICERS STEEL FD-84, FD-1003 M & L for preparing the surface by scrapping with emery paper, filling holes with putty wherever required and painting both internally and externally with two coats of synthetic enamel paint of of olive green shade complete all as specified and as directed by Engineer-in-Charge.

TABLE OFFICE CLERK STEEL FD-84, FD-1004 Removing of existing broken table top of table office clerk steel and supplying and fixing new table top of size 1.2m x 0.61m made out of 18mm thick MDF board with 3m thick TW edging including polishing to teakwood beading complete all as specified and as directed by Engineer-in-Charge.

TABLE OFFICE CLERK STEEL FD-84, FD-1004 Taking out worn out Legs of table office clerk steel without damaging the other components and supplying and fixing the new Legs made out of 25mm square mild steel tubing of 16 gauge and fixing the same by welding to the table in place of removed Legs complete all as specified and as directed by Engineer-in-Charge.

TABLE OFFICE CLERK STEEL FD-84, FD-1004 Taking out worn out short stiffener on bottom legs of table office clerk steel without damaging the other components and supplying and fixing the new stiffener made out of 25mm square mild steel tubing of 16 gauge and fixing the same by welding to the table in place of removed stiffener complete all as specified and as directed by Engineer-in-Charge.

TABLE OFFICE CLERK STEEL FD-84, FD-1004 Taking out worn out long stiffener on bottom legs of table office clerk steel without damaging the other components and supplying and fixing the new stiffener made out of 25mm square mild steel tubing of 16 gauge and fixing the same by welding to the table in place of removed stiffener complete all as specified and as directed by Engineer-in-Charge.

TABLE OFFICE CLERK STEEL FD-84, FD-1004 Removing of unserviceable drawers (Set of 3) including drawer box of table office clerk steel and supplying and fixing new( Set of three) drawer with box of existing size, made out of 1mm thick MS sheet with side channels ,back springs complete all as specified and as directed by Engineer-in-Charge.

TABLE OFFICE CLERK STEEL FD-84, FD-1004 Removing of unserviceable lock of any description and supplying and fixing new locks of grade- II quality and shall conform to IS: 729-1979, with brass 4 lever with duplicate keys as Godrej pattern to table office clerk complete all as specified and as directed by Engineer-in-Charge. Make : Godrej or equivalent to godrej make

TABLE OFFICE CLERK STEEL FD-84, FD-1004 Removing old unserviceable PVC ring/ rubber of table office clerk and supplying and fixing new PVC ring/ rubbers outer suitable for 25mm MS tube complete all as specified and as directed by Engineer-in-Charge.

TABLE OFFICE CLERK STEEL FD-84, FD-1004 M & L for preparing the surface by scrapping with emery paper, filling holes with putty wherever required and painting both internally and externally with two coats of synthetic enamel paint of olive green shade complete all as specified and as directed by Engineer-in-Charge.

TABLE COMPUTER- FD/ E6/MAP-II/03 Removing of old damaged / unserviceable table top from table computer steel and supplying and fixing new table top of 18mm thick pre-laminated particle board, laminated on both sides with 4mm thick teakwood edging all around including polishing to teakwood beading complete all as specified and as directed by Engineer-in-Charge complete all as specified and as directed by Engineer-in-Charge.

TABLE COMPUTER- FD/ E6/MAP-II/03 Removing of old damaged / unserviceable shelf from table computer steel and supplying and fixing new shelf of 18mm thick pre-laminated particle board, laminated on both sides complete all as specified and as directed by Engineer-in-Charge.

TABLE COMPUTER- FD/ E6/MAP-II/03 Removing of old damaged / unserviceable key board tray from table computer and supplying and fixing new key board tray of size 450mm x 480mm of 18mm thick pre-laminated particle board, laminated on both sides complete all as specified and as directed by Engineer-in-Charge.

TABLE COMPUTER- FD/ E6/MAP-II/03 Removing of old damaged / unserviceable drawer from table computer and supplying and fixing new drawer, 75mm deep of 18mm thick pre-laminated particle board, laminated on both sides complete all as specified and as directed by Engineer-in-Charge.

TABLE COMPUTER- FD/ E6/MAP-II/03 Removing of old damaged / unserviceable pull out tray from table computer and supplying and fixing new pull out tray of 18mm thick pre-laminated particle board, laminated on both sides complete all as specified and as directed by Engineer-in-Charge.

TABLE COMPUTER- FD/ E6/MAP-II/03 Removing of old damaged / unserviceable knobs from table computer and supplying and fixing new knob made out of high density material complete all as specified and as directed by Engineer-in-Charge.

TABLE COMPUTER- FD/ E6/MAP-II/03 Removing of old damaged / unserviceable side board from table computer and supplying and fixing new side board of 18mm thick pre-laminated particle board, laminated on both sides complete all as specified and as directed by Engineer-in-Charge.

TABLE COMPUTER- FD/ E6/MAP-II/03 Removing of old damaged / unserviceable nylon buffers from table computer and supplying and fixing new nylon buffers made out of high density material complete all as specified and as directed by Engineer-in-Charge.

TABLE COMPUTER- FD/ E6/MAP-II/03 M & L for preparing the surface of table computer by scrapping with emery paper, filling holes with putty wherever required and painting both internally and externally with two coats of synthetic enamel paint of approved shade complete all as specified and as directed by Engineer-in-Charge.

BOOK SHELF OPEN SMALL STEEL - FD-69 M & L for preparing/cleaning of existing decorated surface of book shelf, scrapping with emery paper, removing all spots, filling holes with putty wherever required and painting with two coats of synthetic enamel paint of olive green shade as approved complete all as specified and as directed by Engineer-in-Charge.

ADJ STEEL SHELVING RACK CLOSE TYPE - TP M & L for preparing/cleaning of existing decorated surface of steel shelving rack, scrapping with emery paper, removing all spots, filling holes with putty wherever required and painting with two coats of synthetic enamel paint of olive green shade as approved complete all as specified and as directed by Engineer-in-Charge.

ADJ STEEL SHELVING RACK OPEN TYPE - TP M & L for preparing/cleaning of existing decorated surface of steel shelving rack open type 975 x 900 x 500mm, scrapping with emery paper, removing all spots, filling holes with putty wherever required and painting with two coats of synthetic enamel paint of olive green shade as approved complete all as specified and as directed by Engineer-in-Charge.

BOOK SHELF OPEN LARGE STEEL - FD-69 M & L for preparing/cleaning of existing decorated surface of book shelf open large steel, scrapping with emery paper, removing all spots, filling holes with putty wherever required and painting with two coats of synthetic enamel paint of olive green shade as approved complete all as specified and as directed by Engineer-in-Charge.

SIDE RACK STEEL 685 X 300 X 760MM W/O TRAY - TP/FD-97 M & L for preparing/cleaning of existing decorated surface of side rack steel, scrapping with emery paper, removing all spots, filling holes with putty wherever required and painting with two coats of synthetic enamel paint of olive green shade as approved complete all as specified and as directed by Engineer-in-Charge.

TABLE CENTRE WITH GLASS TOP - FD-375/SIMILAR PATTERN Removing old unserviceable glass top and supply & fix new glass top with 10mm thick tinted glass complete all as specified and as directed by Engineer-in-Charge.

TABLE BED SIDE - FD-276 Preparing/cleaning /scraping and removing of all dust with using sand paper and filling with wax/putty and applying two coats of French polish match with existing polish complete all as specified in drawing and directed by Engineer-in-Charge.

TABLE OFFICE OFFICER WOODEN - DB-4119 Preparing/cleaning /scraping and removing of all dust with using sand paper and filling with wax/putty and applying two coats of French polish match with existing polish complete all as specified in drawing and directed by Engineer-in-Charge.

TABLE OFFICE CLERK WOODEN - DB-4120 Preparing/cleaning /scraping and removing of all dust with using sand paper and filling with wax/putty and applying two coats of French polish match with existing polish complete all as specified in drawing and directed by Engineer-in-Charge.

CHAIR WRITTING WOODEN - DB-3958 Preparing/cleaning /scraping and removing of all dust with using sand paper and filling with wax/putty and applying two coats of French polish match with existing polish complete all as specified in drawing and directed by Engineer-in-Charge.

CHAIR VERANDAH FD-19 SIMILAR PATTERN Removing the unserviceable plastic cane from seat of chair verandah, cleaning tubular surface of chair and M & L for recaning with 4mm new plastic cane closely knitting as per approved mat pattern complete all as specified and as directed by Engineer-in-Charge.

CHAIR VERANDAH FD-19 SIMILAR PATTERN Removing the unserviceable plastic cane from back of chair verandah, cleaning tubular surface of chair and M & L for recaning with 4mm new plastic cane closely knitting as per approved mat pattern complete all as specified and as directed by Engineer-in-Charge.

CHAIR VERANDAH FD-19 SIMILAR PATTERN Removing old unserviceable PVC ring/ rubber of chair verandah and supplying and fixing new PVC ring/ rubbers suitable for 20mm MS tube complete all as specified and as directed by Engineer-in-Charge.

ALMIRAH STEEL LARGE WITH SHELF GLASS DOOR - FD-104 M & L for preparing the surface by scrapping with emery paper, filling holes with putty wherever required and painting both internally and externally with two coats of synthetic enamel olive green paint of approved shade complete all as specified and as directed by Engineer-in-Charge.

dimalsonsdecorator

M/s. Deepak Traders