PROVN OF WIDENING OF ROAD AT SARAGARHI GATE ALONGWITH CONSTRUCTION OF DRAIN INF SCHOOL MHOW UNDER GE M INF SCHOOL MHOW

Amount

Surface excavation not exc 30 cm deep and averaging 30cm deep and getting out in soft/loose soil complete all as specified and directed.

Excavation over areas not exceeding 1.5 M deep and getting out in soft / loose soil complete all as specified and directed.

M&L 150mm thick (spread thickness) two layer of soling with broken boulders or quarried stone (granite/trap/basalt) interstices filled, surface formed and rolled and consolidated to required gradient and camber with 8-10 tonne power roller, complete all as specified and directed.

M&L for moorum/ red bajri filling under foundation or pavings laid in layers n.exc. 15cm thick spread, levelled, and rammed including watering all as specified and directed.

M&L 150mm thick water bound macadam in two equal layers of 75mm each (compacted thickness) with coarse aggregate of stone (granite/basalt/trap) 63mm to 40mm size, spread rolled and consolidated to required gradient & camber with 8-10 tonne power roller, complete all as specified and directed.

M&L for preparing surfaces of WBM surface with wire brushes for removing caked mud etc and sweeping with brooms and finally fanning to clean the surfaces with gunny bags to remove all loose dirt etc and applying evenly a tack coat with bitumenous primer using paving bitumen VG-30 at the rate of 10 kg / 10 sqm over WBM surfaces and M&L for premixed hot mix Asphaltic Semi Dence Concrete using 5.5% binder content (VG-30 Grade paving bitumen) by weight of total mix and with thickness of 30 mm (consolidated Thickness) including rolling with 8 to 10 tonne power road roller to uniform and smooth surface and consolidation to required gradient and camber all as specified and directed. (Note: - (i) Laying shall be done by means of self-propelled mechanical paver, finishing with electronic sensor and hydraulic controls with suitable speed and capable of laying, spreading, tamping and finishing. (ii) Mix shall be obtained from hot mix plant and spreading shell be done by using mechanical paver only)

M&L for premix bituminous macadam (consolidated thickness not more than 75 mm) with 4% binder content of paving bitumen of grade (VG-30) by weight of total mix laid and rolled with 8-10 tonne power roller to required gradient and camber up to outer edges of roads on existing black top surfaces complete all as specified and directed. NOTE: - (i) Cost of testing charges, materials and transportations etc for job mix formula shall be inclusive in the unit rate and no extra payment shall be admissible on this account. (ii) Mix shall be obtained from hot mix plant and spreading shall be done by using mechanical paver only.

M&L for marking lines, dashes, arrows, letter etc 15 cm wide on bituminous surface with retro reflective thermoplastic road marking paint with reflector sing glass beads @ 250 gms per sqm area conforming to MOST & BIS specification ,of thickness 2.50 to 3.00 mm thick of colour white/golden/yellow as approved by GE and applied by using automatic road making spray machine as per manufactures instruction including preparation of surface ie cleaning of surface by removing all dust ,dirt,oil grease etc complete all as specified and directed

S&F in repair Cat Eye as (Road Stud) two way reflective type of aluminium alloy body of size 110mm x 120mmx 24 mm and weight of 435 gms in Red, Amber or white in colour fixed with and including all necessary items as per manufactures instructions complete all as specified and directed. (Make - Dark Eye Model No DA 972.0 or equivalent of 3M/Sun Eyes)

S&F in repair solar cat eye aluminum alloy shall (100% water proofing design according to 65) of size 125mm x 125mm x 25mm (shank 65mm) of high efficiency Mono rystafie solar panel 2.4V/0.3 watt one NI-ed rechsrgeable battery (1.2V/ 1600MA) consisting of super bright LED with 10,000 to 18,000 mcd completed as per manufactures instructon etc all as specified and directed complete all as specified & directed. Make - SUNEYES/ Dark Eye / 3M/Alcolite/solar

S&F in repair road Solar delineator made of 50 mm round MS pipe 80 to 100 cm high above ground level with high four quality LED flashing light of red or yellow in colors with operating tme of 3-4 consecutive days (with full charge) complete all as specified and directed as per manufactures instructions complete all as specified & directed. . NOTE : 1. Excavation, removal of surplus soil and size of pcc pit is 200mm x 200mm x 200 mm filled with pcc 1 :2:4 type B-1. rate quoted shall be included above. Make - Dark Eye (Model No : DA 112 ) or equivalent of SUNEYES/ 3M/Alcolite/solar

Dismantling of stone slab dry & pointed, Paving stone and tiles of any description or thickness as in floors, appron , path etc. Laid bedded and pointed in any mortor complete all as specified & directed.

M & L 80mm thick Machine pressed rubber moulded precast concrete interlocking paver block glossy look any shape and size confirming to IS 15656 2006, M-35 grade with grey coment and pigment laid on 30mm thick sand cushioning laid dry to the profile all as specified and as directed (Note:- Sand cushioning shall be measured and paid separately) (Make :- Mehatab Tiles, NITCO tiles ,Metro tiles, Dayal shri Processors)

M & L 30mm thick sand cushioning / stone grit filling under under pavement including watering consolidationg with clean dry sand, complete all as specified and as directed

M&L for PCC (1:4:8), type D-2, using 40mm graded stone aggraegate as in foundation filling and mass concrete complete all as specified and as directed.

M & L for granite or trap stone kerb of roughly squared stones of size 20cm X 30cm, all surfaces hammer dressed so that the maximum depression from straight edge held against the dressed surface shall not exceed 20mm jointed in cement mortar 1:6 and struck flush complete all as specified and directed

Removing excavated materials (soil) to a distance exc. Exc. 250m but n exc. 500m and depositing where directed at a level n exc. 1.5m above the starting point complete all as specified and directed

Excavation in trenches in soft/loose soil and not exc 1.5 m wide and n.exc 1.5 m in depth in foundation, etc and getting out complete all as specified and directed complete all as specified and directed.

Returning , filling including spreading levelling , watering and well ramming in layers n.exc 25 cm complete all as specified and directed.

M & L PCC 1:3:6 type C2 using 40mm graded aggregate as in surface channels and channels complete all as specified and directed.

Material and labour for Burnt brick work with whole kiln burnt well burnt modular size bricks of compressive strength not less than 35Kg per Sq cm built in CM (1:4) in walls straight on plan/exceeding 6 meter mean radius,finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15mm thick on fair faces of brick work surfaces in cement mortar 1:4, finish the surface even and smooth without using extra cement all as directed and specified.

Extra for forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement, including forms, mound, mitred/ stopped end etc.

M & L for providing cement concrete (1:2:4) type B1 using 20mm graded stone aggregate as in cills, seismic and other similar bands plingth courses, coping , bed plates, bond stones etc including weathering, slightly rounded or chamfered angles and throating as directed including necessary form work as required complete drains, coppings & Surface channels complete all as specified and directed

M&L for PCC 1:2:4 type B1 using 20mm graded stone aggregate in surface channels and drains all as specified and directed

M & L for precast reinforced cement concrete (1:2:4) type B1 using 20mm graded stone aggregate as in kerbs and edging to road , divided and footpath cover slab for small culvert, manhole and soak well septic tank etc and setting in cement mortar (1:4) complete including necessary use and waste of form work complete all as specified and directed. (Note :- Reinforcement shall be measured and paid separately under relevant item)

Material and labour mild steel TMT bars 10mm dia and over cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips etc complete all as specified and directed.

M & L for Mild steel TMT bars 6mm to 8mm dia cut to length bent to shape as required including cranking bending spirally, hooking and binding with & including MS wire 0.9 mm dia etc complete all as specified and directed.

S&F PVC (SWR) pipe 110 mm bore single socketed, cut to any length in single piececomplete all as specified and directed.

J B CONSTRUCTION AND DEVLOPERS

KAILASH CHANDRA KHANDELWAL