SPECIAL REPAIRS TO EXTERNAL ELECTRIFICATION BY CONVERSION OF HT OH FEEDER TO HT UG CABLE AND PROVN FOR CONVERSION OF EXISTING LT OH TO LT UG CABLE AND CONNECTED WORKS AND ADDN/ALTN TO GUARD ROOM AND TOILET UNDER GE (U) SECUNDERABAD

Amount

Supply & Erecting Steel Tubular Swaged Pole Type 410-SP-55 (11.0 METRE long) including Cast Iron Base Plate, Finial Taper Plug, Cap, Mild Steel Bolts, Nuts, Screws including applying Two Coats of Black Bituminous Paint Internally and Externally upto Planting Depth and applying with Two Coats of Aluminium Painting over a Coat of Aluminium Primer (Externally from Top of Coping) including Writing MES Pole No. with Synthetic Enamel Paint (First Grade/quality), complete all as specified and as directed.

Supply, Laying, connecting, Testing and Commissioning of XLPE insulated screned PVC beded galvanised steel strip or wire armoured earthed electric power cable (heavy duty) with aluminium couductor 11 KV(E) grade suitable for earthed system cross sectional area 95 sqmm 3 core H.T.U.G cable laid in tranches/through GI pipe/fixed along with pole complete all as specified & directed. Make- ICC, CCI, Polycab, Havells, KEI.

Supply & Lay GI tubing light grade of following size 80 mm for cable protection on road/drain/floor/Pole including necessary clamps. .40x4mm. Make : TATA/Jindal/Bansal with ISI makred.

Switch air break gang operated triple pole mechanically operated mounted on 10 KN insulators insulator and steel frame out door type suitable for Horizontal / vertical installation single / double brake provided with locking arrangement, consisting of MS channel, HT post type insulator ,copper alloy high pressure assembly, operating rod of 25 mm dia GI pipe medium grade confirming to IS-1818 of 1972, suitable for 11000 volt, 400 Amps, short time withstand current 25 KA for 3 sec complete all as specified.

M&L for air break switch, rocking type, Gang operated, triple pole, mechanically operated, mounted on insulator and steel frame, with operating mechanism worked from ground level, for current rating upto 400 amps suitable for 11000 volts complete all as specified and as directed.

S&F drop out fuse unit woth 10 KN insulator suitable for 11000 volt ,100 amps mounted on MS channel complete with post insulator fuse barrel etc for 3 phase.

Lightning arrester non linear complete with all fittings distribution class discharge capacity 65 kilo amp, current rating 5 kA suitable for 11000 volt complete with all fittings.

Anticlimbing device ,spikes type fabricated out of ms bars(round,square and flat )including nuts, bolts, washers and welding in two halves made to shape to suit cross section of the pole and painting with two coats of aluminium paint over a coat of primer.

Danger notice plate of 1.6 mm thick mild steel sheet vitreous white ,with letters ,figures and fixed with ms clamps bolts and nuts of size approved size for HT of size 25cmx20cm confirming to IS-2531.

S&F cable end termination suitable for XLPE, HT 11 kv (E) under ground cable, 95 sqmm, 3 core,11000 volt, heat shrink type out door end termination including all jointing material complete all as specified and directed. Make: Birla 3m/m-seal/3M /DENSON

S&F of cable route indicator for HT round shaped 150mm dia 10mm thick with marking of 11 KV, HT welded bolted on angle iron of 25x25cm of 60 cm length grouted in PCC 1:3:6 TYPE C2 block of size 150X150X150mm embedded in ground including nece exc earth work complete all as directed.

M&L cross arm bracing support clamp back plates fabricated from structural steel section including nut bolt washer welding, bending, cold or not drilling holes for bolt in any shape or size as directed & incl two coat of aluminium paint over a coat of red oxide primer complete all as specified & directed.

Supply, Install, Testing and Commissioning of Advance Maintenance Free G.I. SAFE EARTHING Electrode with PIPE of not less than 50 mm outer dia) and two meter length, The electrode should be of galvinised (80 -100 micron) along with earth lead as Galvanised steel strip of size 32 X6 mm 7.5 m. The GI Electrode shall be pre-filled with Cristaline Conductive Material (CCM). The GI electrode shall be surrounded with 25 kg BackFill compound to provide maximum contact between the electrode and Back Fill Compound. The earting pit cover should be factorty built (size TOP- 10 Inch, Bottom -13 Inch, Height 10.25 Inch ) made of heavy duty Polypropylene complete all as specified and directed. Make: ASHLOK/INDELEC/JMV/TERCEL/TRUE POWER

Supply and fix galvanized earth strip 32 mm x 6 mm for earthing from earth plate to equipment complete all as specified and as directed.

Aluminium conductor steel rainforced for over head lines,securing on poles complete including binding wire jointing sleeves ,aluminium taps etc all as specified of sizes squirrel/weasel/ferret/mink.

Pin type,porcelain,vitreous,white,brown or green insulator including one galvanised mild steel spindle,two galvanised iron washers and one galvanised iron nuts ,150 mm hight,150 mm dia for 11000 volts 10 KN

S&F disc type insulator vitreous 145 mm high and 255 mm dia ball and socket type white /brown 70 KN "two in one series" assembly for tension with clamps for conductor suitable for 11000 volt working pressure complete all as specified and as directed.

Dismantling and taking down existing cross arms from pole

Taking down HT over head line copper/ aluminium from pole / insulator complete with guarding & cradlesall as specified and as directed .

Taking down carefully existing pin /disc HT insulator from pole.

Excavation in trenches not exc 1.5 mtr wide and n.exc 1.5 mtr in deep and getting out in Hard/Dense soil for laying of cables etc.

Excavation in trenches not exc 1.5 mtr wide and exc 1.5 m depth but not.exc 3.0 mtr in deep and getting out in Hard/Dense soil laying of cables etc.

Excavation in trenches not exceeding 1.5 m width and not exc 1.5 m in depth and getting out in any type of rock for laying of pipe line complete all as specified and directed.

Returning filling in including spreading, leveling watering and well ramming in layers n.exc 25cm thick using excavated soil

Returning, filling in, including spreading, levelling,watering and well ramming in layers not exceeding 25 cms in soft disintegrated rock

Removing excavated surplus soil/rocks to a distance n.exc 50 mtr and depositing where directed at a level n.exc 1.5mtr above from the starting point

Removing surplus rocks to a distance exc. 250 m but n exc. 500 m depositing where directed at a level n.exc 1.5 m above the starting point all as specified.

Supplying and laying un-reinforced precast concrete cable cover class HV , Type 1 flat with size 300mm x180 mm x 40mm all asspecified and directed by Engr-in-Charge.

Spreading riddled earth ( after preparation of excavated earth) in Cable duct for cushioning of cable laid in trenches complete all as directed by Engineer-in-Charge Note:- Punned thickness 18 CM( 6.25 Cm below cale and 11.75 cm above cale) will be measured for payment purpose. The earth removed during excavation to be used as rddled earth after crushing and sieving. Quoted rate inclusive of all arrangement as mentioned.

M&L cutting of road, hard standing made of concrete or premix carpet, WBM, soiling and morrum filling including excavation for laying of cable pipe all as directed and making good the road/hard standing by using all old/new materials and with PCC (1:2:4) etc, required to match with the existing surface complete all as specified and directed.

M&L for road crossing/drain crossing by adopting trench less tunneling work through specified pipe jacking method by erecting the equipment to true to the allignment and gradient by haidrolic pipe jacking technique complete including tunneling, excavation in any type of soils including hard rock, GI Pipe 100 mm dia medium grade in any length including jointing materials to carry HT UG cables of size 95 Sqmm 3 core and necessary conveyance charges of machinery and other required materials in co-ordination with the concerned authorites complete all as specified and as directed. Note : Quoted rates deemed to be inclusive of GI Pipes 100 mm dia medium grade

Cement Concrete 1:2:4 TYPE B1 (20mm Graded Stone Aggregate) as Lean Concrete in Foundation of Poles, Stay Assembly, etc., including Formwork and foundation of GI pipe , BOLLARD LIGHT (as/if required), complete all as specified and as directed.

Cement Concrete 1:3:6 Type C1 (20mm Graded Stone Aggregate) as in Coping of Poles, etc. including Formwork (as/if required), complete all as specified and as directed.

M&L for shingle filling in substation / around 4 pole structure / transformer yard of Gauge 40 to 63 mm, deposited, spread and levelled in layers not exc. 150mm thick, watered and rammed to a True Surface, complete all as specified and as directed.

Surface excavation not exc 30 cm deep and averaging 15cm deep and getting out hard/dense soil

Rough Excavation n.exc 1.5 m deep and getting out hard/dense soil

Supply, Installation, test and Commissioning CPRI APPROVED factory fabricated, out door type, LT FEEDER PILLAR BOX made out of 3.00 mm thick CRCA Sheet with projected Globe roof for rain water protection Dust and Vermin Proof, Double door with both side opening including Neoprene Rubber Gasket, suitable for 440 Volt 3 Phase 4 Wire System , including Danger Plate, Earthing Strip Point and Ventilation Louvers at Rear Side, Bottom detachable Gland Plate complete with suitable size Zinc Chromium Plated Nuts, Bolts and Washers, etc. and embeded with 50X50X5mm Mild Steel Angle Iron Frame and 500 mm above the Normal Ground Level complete with internal connection with suitable size of cable, cable lugs and cable glands PCC Foundation in Cement Concrete 1:3:6 (20mm Graded Stone Aggregate) and Testing after Installation complete all as specified and comprising of the following :–

(a) Aluminium bus bar 400amps - 04 Nos, supported with suitable size of heavy duty porcelin stand lock with suitable size of brass nut, bolts and washer with heat shrinkable PVC sleeving. The bar shall be colour coded (red, yellow and blue) for three phases and black for neutral. (b) MCCB 160 amps, 415 volt, 25 KA Breaking capacity 4 pole Electromagnetic release duly connected to Bus Bar as INCOMING - 01 Nos. Make : Legrand model No: 420218 or equivalent from Schneider /L&T/Hagar/C&S as approved by GE (c) MCCB TP,63 Amp, 3 Pole, 415 Volt, 16 KA Breaking Capacity duly connected to Bus bar as OUTGOING - 03 Nos. Make : Legrand model no: 420005 or equivalent from L&T/Hagar/C&S as approved by GE (d) LED indicating lamps with holder for main supply indicating RYB - 01 set (03 Nos), Make : AE/L&T or equivalent make as approved by GE. (e) Instrument fuse holder, fused 4 amps - 06 Nos. Note : Size of the panel board should not be less than 1.0 x1.2x.35m

Supply, Installation, test and Commissioning CPRI APPROVED factory fabricated, out door type, LT FEEDER PILLAR BOX made out of 3.00 mm thick CRCA Sheet of size 0.5MX0.45Mx0.35M with projected Globe roof for rain water protection Dust and Vermin Proof , Double door with both side opening including Neoprene Rubber Gasket,, suitable for 440 Volt 3 Phase 4 Wire System ,including Danger Plate, Earthing Strip Point and Ventilation Louvers at Rear Side, Bottom detachable Gland Plate comp-lete with suitable size Zinc Chromium Plated Nuts, Bolts and Washers, etc. and embeded with 50X50X6mm Mild Steel Angle Iron Frame and 600 mm above the Normal Ground Level comp -lete with internal connection with suitable size of cable ,cable lugs,and cable glands PCC Foundation in Cement Concrete 1:3:6 (20mm Graded Stone Aggregate) and Test-ing after Installation complete all as specified and comprising of the following :– (a) Aluminium bas bar 200amps - 04 Nos, supported with suitable size of heavy duty porcelin stand lock with suitable size of brass nut, bolts and washer with heat shrinkable PVC sleeving. The bar shall be colour coded (red, yellow and blue) for three phases and black for neutral.

Supply, Installation, test and Commissioning CPRI APPROVED factory fabricated, out door type, LT FEEDER PILLAR BOX made out of 3.00 mm thick CRCA Sheet of size 0.75 MX.70mX.35 M with projected Globe roof for rain water protection Dust and Vermin Proof , Double door with both side opening including Neoprene Rubber Gasket,, suitable for 440 Volt 3 Phase 4 Wire System ,including Danger Plate, Earthing Strip Point and Ventilation Louvers at Rear Side, Bottom detachable Gland Plate comp-lete with suitable size Zinc Chromium Plated Nuts, Bolts and Washers, etc. and embeded with 50X50X6mm Mild Steel Angle Iron Frame and 600 mm above the Normal Ground Level comp -lete with internal connection with suitable size of cable ,cable lugs,and cable glands PCC Foundation in Cement Concrete 1:3:6 (20mm Graded Stone Aggregate) and Test-ing after Installation complete all as specified and comprising of the following :– (a) Aluminium bus bar 200amps - 04 Nos, supported with suitable size of heavy duty porcelin stand lock with suitable size of brass nut, bolts and washer with heat shrinkable PVC sleeving. The bar shall be colour coded (red, yellow and blue) for three phases and black for neutral. (b) MCCB 100 amps ,415 volt ,16 KA Breaking capacity 4 pole Electromagnetic release duly connected to Bus Bar As IN COMING - 01 Nos. Make Legrand model no: 420015 or equivalent from Schinder/L&T/Hagar/C&S as approved by GE

Design, Supply, Installation, testing and Commissioning CPRI APPROVED factory fabricated, out door type, LT FEEDER PILLAR BOX IP 55 protection grade, made out of 3.15 mm thick CRCA Sheet with projected Globe roof for rain water protection Dust and Vermin Proof , Double door with both side opening including Neoprene Rubber Gasket,, suitable for 440 Volt 3 Phase 4 Wire System ,including Danger Plate, Earthing Strip Point and Ventilation Louvers at Rear Side, Bottom detachable Gland Plate comp-lete with suitable size Zinc Chromium Plated Nuts, Bolts and Washers , cable glands of appropriate size , etc. and supported with 65X65X6mm Mild Steel Angle Iron Frame and 500 mm above ground lavel, embeded in PCC 1:2:4, type C-2, 45 Cm below ground level and 50 Cm above ground level complete with internal connection with suitable size of strip, cable lugs,and cable glands and testing after Installation complete all as specified and comprising of the following :-

(a) Bus bar aluminium duly insulated with colour coded heat shrinkable sleeve and mounted on suitable size of 'F' class insulators made of non hygroscopic, non combustible, track resistant high strength FRP insulators 400 Amps for phases and Neural, set of 4 for RYB &N - 01 set. (b) MCCB 4 Pole 200 Amps 25KA -01 No. Thermal Magnetic release (incommer) (c) MCCB 4 Pole 160 Amps 16KA -02 Nos. (Outgoing) (d) MCCB 4 Pole 125 Amps 16KA -02 Nos. (Outgoing) (e) MCCB 4 Pole 32 Amps 16KA -02 Nos. (Outgoing)` (f) Three phase Panel mounted Digital type Voltmeter meter 0-500 Volts, Ammeter 400/5A LT-CT operated complete - 01 Set (g) Indicating type lamp for Red, Yellow and Blue phases - 01 Set Note : Size of the panel board should not be less than 1.1 M X1.4 MX0.40M

Notes for Item Nos 37to 40.01: (a) All incoming and outgoing cables are to be connected to the above panels with proper lugs, double compression copper stain less steel gland, nuts, bolts etc, the cost of the items deemed to be inclusive in the quoted rates. (b) Make of MCCB's and MCB's to be used in the panels are : L&T/Legrand /Siemens/ Havells/C&S as approved by GE. (c) The panel shall be Fabricated from a reputed firm(CPRI Approved) . (d) All Internal connection between ACB, MCCB ( ABOVE 63 AMPS ) and Changeover and Bus bar shall be done by aluminium strip of suitable size and capacity . (e) All MCCB to be connected with both side Spreader Link and all Incomer and outgoing MCCB of Panels should be thermal magnetic release with adjustable settings (Min 70.5 to 100 %) and Ics = 100% Icu (f) Sufficient space to be provided for cable connection between MCCB and Bottom of the panel board.( Minimum space for MCCB up to 200 amps = 35 CM , Minimum space for MCCB 250 to 400 amps = 45 CM , Minimum space for MCCB above 400 amps = 55 CM ) (g) Base of the panel should not be less than 500 mm above the ground level. Necessary PCC for base /foundation required deemed to be included in the quoted rate. (h) Cable alley / chamber to along with connector of suitable size to be provided for connection of Outgoing cable . (j) Necessary approval of drawing to be taken from GE before placing order to the manufacturer. (k)All existing incoming and outgoing cables also to be connected to the above panel as per site requirement with proper lugs, glands nuts, bolts etc (l) Door hinge of industrial type heavy duty to be provided minimum 3 Nos for each door (m) The rate shall deemed to be inclusive in the item rate for al the points mentioned above.

Supply and lay in trenches/fixed to walls/poles, connecting using LUGS etc and testing of XLPE insulated and PVC sheathed heavy duty LT UG 1100 Volts grade armoured under ground cable with aluminium conductor cable of 2 Core 10 Sqmm all as directed. Make : Havells/Finolex/KEI/POLYCAB/GLOSTER Note :- Earth work excavation, sand cushioning and brick protection shall be measured and paid separately.

All as per item No 41 here-in-before but 4 Core 16 Sqmm

All as per item No 41 here-in-before but 3.5 Core 25 Sqmm

All as per item No 41 here-in-before but 3.5 Core 50 Sqmm

All as per item No 41 here-in-before but 3.5 Core 70 Sqmm

All as per item No 41 here-in-before but 3.5 Core 95 Sqmm

All as per item No 41 here-in-before but 3.5 Core 120 Sqmm

Taking out and Relaying of LT cable of size 10sq mm to 50 Sqmm 2/3.5 core after carrying out necessary Repair such as joining with Epoxy joint and laid with sand Cushioning and brick protection and making connection By using Lugs all as specified and directed by ingr in charge. Note: Earth work, sand cushioning, brick protection, Lt Joints shall be measured and paid separately under Relevent Item.

Supplying and laying of following size HDPE pipe pn 10 ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc.direct in ground, wall, floor complete all as directed

Supply and Fixing of cable jointing kit for 1.1 KV grade cable for outdoor termination heat shrinkable type joint complete with jointing material and accessories suitable for 3.5 core XLPE armoured aluminium conductor cable of size 35 sqmm to 50 sqmm complete including taking out old unserviceable one all as specifide and directed.

S&F cable jointing kit for 1.1 KV grade cable for outdoor termination heat shrinkable type joint complete with jointing material and accessories suitable for 3.5 core XLPE armoured aluminium conductor cable of size 70 sqmm to 120 sqmm complete including taking out old unserviceable one all as specifide and directed.

M&L for brick protection cover of old size bricks common burnt clay building bricks sub class ’B’ laid dry and flat abutting each other with width equal to length of brick and gap between adjacent bricks not exceeding 10 mm complete all as specified.

M&L for stright Through Joint heat shriankable type suitable for 1100 volt 70 to 120 Sqmm 3.5 core complete all as specified and directed

M&L for stright Through Joint heat shriankable type suitable for 1100 volt 25 - 50 Sqmm 3.5 core complete all as specified and directed

Cutting the existing building plinth protection/ Floor by using suitable cutter , depth and width as required for laying of LTUG Cable of any size /any kind of pipes pipes up to 50 mm dia and making good of disturbed surface shall be made with cement concrete 1:2:4 type B1 (using 20 mm graded stone aggregate) and cement morter on any other things as required to match with the adjoining surface complete all as specified and directed.

Disconnection existing LT UG cable of any size from pole/Oh line and connect the same to federpiller box by usinf cable glands , lugs etc as required complete all as directed

S&F hot press moulded SMC junction / terminal box of size with internal diamensions of 200 x 140 x 95 mm with hinged door, incl provision of 2 way connector 415 Volts made out of polycarbonate or bakelite and 1 No MCB of 6 Amps with DIN bar, drilling holes for cable connections, connecting incoming and or out going cables by providing suitable of size of cable lugs/glands, fixied on pole by means of clamps made out of MS flat iron of size 25 mm x 3 mm including dismantling of old unserviceable all as specified and as directed. Make: Hensel/Syntex/C&S/Nyptune

Supply and lay PVC Insulated , PVC sheathed industrial HV round multicore flexible cable with copper conductor three core 1.5 sqmm including PVC conduit 20 mm dia medium grade and necessary bends, GI Clamps , fittings and fixtures as required for connection of light fittings. (to be used for Street light connection from JB to Street light).

S&F PVC insulated unsheathed/sheathed cable with stranded Aluminium conductor 1100 Volts grade, flat twin core service cable of size 4 Sqmm conforming to IS:694/1990 with latest amendments ISI including disconnecting/taking out existing unsv/damaged old service cable complete all as specified and directed. Make : Richa/havells/fincab or equivalent.

All as per item No 59 above but of size 6 Sqmm complete all as specified and directed.

Making hole 2 Nos on existing steel tubuler pole of suitable size for passing of Street light connection wire from Junction Box to street light complete all as directed

Demolition of coping of pole as required for placing of cable protection pipe and making good the same by using PCC complete al as speccified and directed. Note: Quoted rates inclusive of PCC

S&F cable route indicator made out of CI round shape of 65 mm dia fixed with MC Angle 25X25X3 Mm of length not less than 45 CM embeded in PCC of size 25CMx25CMx25cm including necessary excavation etc complete all as specified and directed.

Supplying, erecting and fixing steel tubular swaged poles with cast iron base plate of size 300mm x 300mm x 6mm, finial taper plug, bolts, nuts & screws for type 410 SP-31 (9.0 mtrs long) including painting with two coats of aluminium paint over one coat of red oxide primer on all exposed surfaces and tarring with black bituminous paints to embedded portion in PCC and providing 3 Nos of 30cm wide circular bands with black & yellow paint starting from plinth level at a gap of 30 cm in between 2 bands and numbering of poles, in yellow paint over black painted back ground at a height of 2m from bottom of pole with 5 cm large bold letters 2" (inch) wide complete all as specified and directed including taking down old unsv. Note:- (i) Crane charges for erection shall be deemed to be including in quoted rate. (ii) Earth work,PCC,coping shall be measured and paid separately. (iii) The rates include staying the poles in atruely vertical position till the foundations are properly set. (iv)The rates deemed to be inclusive of cast iron base plate,nuts,bolts,screws,painting of steel tubular poles,drilling of holes in steel tubular poles for fixing of clamps,hooks for continuous earth wire/strip.

S&F lantren of dia 60 CM for fixing of flood light, cap type to be fixed on the top of 9 m SP-31 Steel pole , made of MS pip medium grade dia greater than the top dia of the pole of length 0.35 M supported by MS flat iron of size 50X6 mm 8 Nos including two coats of aliminium painting over a coat of redoxide primer complete all as directed

Supply, fixing, connecting and testing energy saving, environmental friendly long life Varsatile pressure die cast aluminium alloy for housing (heat sink) with IP66 protection road way light fitting with high power LED as light source of capacity 90 watts with warranty option of 2 years with suitable driver and cable gland for maintaining ingress protection with Epoxy powder coated siemens grey finish after phosphochromate treatment, Tempered protective toughened glass,thermal shock and impact resistant fixed to the housing with SS screws , High efficiency long life LED chip in modules with lumen efficacy of >140 lm/W with PC lens and system lumen 6000. Powered by Built-in electronic LED driver with APFC (SMPS based constant current supply), lower THD, Open Circuit protection, Phase to Phase protection, Over Voltage protection, Surge Voltage protection. CCT 5700, CRI>70, THD<10%, PF>.95, IP66, IK07.Life class of 50,000 hrs @ L70, Operating Temperature:-10 TO +50 DEG.C; Input Supply Voltage Range:140-270 V, Frequency : 50-60 HZ, Driver

Safety requirement standards : IS 15885-2-13, Test report to be submitted for Driver performance requirements as per IS 16104, for Photo bilogical safety norms as per : IS 16108, Certification as per LM 79 for Luminaire, LM 80 for LED Source, with all standard accessories etc, including connection by using 3 core 1.5 sqmm HV Round Cable complete all as specified and as directed. Make : Philips Model number BRP409 LED 115 CW SLC FG PSU GR V2 or Havells Cat No. ENDURAPEARLPLUSSL90WLED757PASYTOPCASTHO, SURYA CAT NO: SLEUL90W IP66 PLX XL or Wipro cat No. LR02-102-XXX-57-G2.

All as per item No. 67 here-in-before but Flood light of high power LED as light source of capacity 150 watts.. Make : Bajaj Cat No.BARFEG 150W LED or Havells Cat No. JETAIRISFLS150WLED757PSYMLTG, SURYA CAT NO SLEFL150 W IP66 LUMOS MAX or Wipro cat No. LF20-192-060-57-G2 OR CG MODEL nO LFLN-150-CDL/60-M

Fabrication and installation of GI pipe bracket on any kind of pole made of midium Grade tubing of size 40 mm dia, duly bended by hot forgoing after filling of sand, length 1.20 mtr including providing two pair of MS flat strip clamps 40 mm x 4 mm with GI bolts nuts and washer complete all as specified and directed

Dismantling stay assembly complete. (demolition of concrete, etc. and excavation measured separately)

M&L for drawing two runs of PVC insulated unsheathed single core multi stranded copper conductor FRLS cable of size 1.50 sq mm with one run of PVC insulated unsheathed single core multi stranded copper conductor FRLS cable of size 1.50 sq mm including 20mm dia PVC conduit exclusive of boxes but inclusive of all tees, bends, elbow, reducers etc and fixing accessories such as couples, lock nuts, saddles, pipe hooks, 3 sets of clamps of suitable size for supporting on pole etc complete all as specified. Note: The above mentioned wire to be used for connection of lights from Junction box. Quoted rates deemed to be inclusive of clamps of suitable size required for the same .

M&L for concealed point wiring for one light/Fan controlled by 1 one way switch with 1.5 Sqmm PVC insulated unsheathed single core multi-stranded copper conductor (FRLS) cable 1100 Volts grade drawn through and including 20 mm dia (medium grade) rigid non metallic PVC concealed conduit along with 1.5 sqmm continuous PVC insulated unsheathed single core multi-stranded copper conductor (FRLS) cable for earth continuity wire, connected to earth dolly and to be terminated in and including pressed steel sunken boxes , readily available (Having wall thickness not less than 1.22 mm for boxes upto a size of 200 mmX300 mm and beyond that the wall thickness shall be not less than 1.60 mm) concealed type with 3mm thick bakelite sheet cover for mounting switches, sockets, fan regulators etc including testing on completion complete including cutting chases for concealed conduit pinning in making good to facing and pointing in using cement mortar 1:3 and making good disturbed surface all as specified and as directed. Make:-Plaza/Havells/Mescab

All as per Item No 72 here-in-before but for one switch socket outlet, 5 Amp on same board with other switches all as specified and as directed

All as per Item No 72 here-in-before but for one three pin switch socket outlet, 5 Amp on independent board all as specified and as directed.

All as per Item No 72 here-in-before but for one15 Amp 3pin switch socket outlet, independent with 2.5 Sqmm single core multi-stranded copper conductor cable (FRLS) along with 1.5 sqmm continuous PVC insulated unsheathed single core multi-stranded copper conductor (FRLS) cable for earth continuity wire all as specified and as directed.

S&F switch piano flush button single pole one way 5 amps all as specified and as directed Make:Anchor/Havells/GM

S&F socket outlet 5 pin 5 amp flush type all as specified and as directed Make:Anchor/Havells/GM

S&F switch socket outlet 5 pin 5 amp flush type all as specified and as directed Make:Anchor/Havells/GM

S&F switch socket out let multipurpose 3 pin 15 amp and one 3 pin 5 amp controlled by one switch all as specified and as directed. Make:Anchor/Havells/GM

S&F ceiling rose surface bakelite three terminals all as specified and as directed. Make:Anchor/Havells/GM

S&F fan regulator electronic deluxe rotary step type.(Make : Anchor/Havells/GM ) all as specified and as directed.

S&F indoor luminare decorative batten for wall/ceiling mounting box type energy efficient saving LED 1x9/10W -2FT .incl twin twisted copper conductor flexible wire from ceiling rose to connector all as specified and as directed. Make C&S /Philips/Surya/ Bajaj.

S&F indoor luminare decorative batten for wall/celling mounting energy efficent saving LED 1x20W-4FT incl twin twisted copper conductor flexible wire from celling rose to connector all as specified and as directed. Make : C&S or equivalent of Philips/Havells/Surya/Bajaj

S&F on wall security LED light luminaire fitting 1X20 W and including cable for connection from celling rose with 1.5 Sqmm PVC insulated stranded copper conductor (FRLS) cable including 25 mm GI bracket medium grade 1m long bent to shape including bolt, nut,washer,clam made out of MS flat of size 25X3 mm , 4 nos Anchor Bolt of suitable size etc all as specified and as directed by the Engineer-in-charge . Make : CG MODEL LST 20 CDL/ SURYA MODEL SLE UL 20 W IP66 LXN

M&L for sub main wiring with two single core PVC insulated (unsheathed) multi strand copper conductor FRLS cable of size 4 sqmm and one single core PVC insulated (unsheathed) multi strand copper conductor FRLS cable of size 2.5 sqmm as in continuous earth wire drawn into and including concealed PVC conduit medium grade 25mm dia ISI marked complete with fittings and fixings accessories complete and including cutting chases pinning in making good to facing and pointing in using cement moter 1:3 to the ends and making good disturbed surface complete all as specified and as directed.

S&F sheet metal enclosure for MCB, DBs, phosphatised, Powder coated , single pole and neutral (SPN) 240 Volt ,, suitable for 8 way with dim rail earth and neutral bar all as specified and as directed. Make: Legrand or equivalent of Havells/Hager/C&S

S&F in proper position MCB double pole of capacity upto 32 amps, 240 Volts C-curve with 10kA breaking capacity all as specified and as directed. Make: Legrand or equivalent of Havells/Hager/C&S

S&F in repair MCB Single Pole (SP) C curve 10kA breaking capacity of 6 to 32 amps, 240 Volts in proper position all as specified and as directed. Make: Legrand or equivalent of Havells/Hager/C&S

S&F Ceiling fan of Size 1200mm sweep, 230 volt Ac with connection from existing celing rose with MS hooke for hanging of suitable size all as specified and as directed Make :-Usha/Havells/Bajaj.

S&F Exhaust fan 200 mm sweep PVC body , single phase with louver shutter and connecting up including provision of hold fasts for fixing fan and louver shutter with cutting of hole and necessary PCC(1:3:6) all as specified and as directed.

S&F wall mounted fan of Size 400mm sweep, 230 volt Ac with connection from existing celing rose with necessary fixing arrangement complete all as specified and as directed Make :-Usha/Havells/Bajaj.

Dismantling timber scantlings in fillets, rails, posts, rafters, purlins, etc. under 40 sq. cm in section for framed work

Dismantling Asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings

Taking down chowkhats or frames exc 1.5 sq. m but n exc 4 sq. m each with shutters (without taking off shutters from the frame)

Demolition of Brickwork or stone/ boulder masonry, built in lime mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles

Demolishing lime concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level)

Taking up or down steel tubing and connections, and removal from site of bore 15mm

All as per item No 97 above but bore 20mm

Demolition and breaking up drain pipes (Salt glazed ware, AC or Reinforced concrete) set in cement mortar for 100mm internal dia

Demolition Stone slabs and tiles of any description or thickness in floors, aprons etc. laid, bedded and pointed in any mortar

Removing old lime wash (if any), hacking for key, raking out joints of old brick work or stone work built in lime or mud mortar; not previously plastered; and scrubbing down with water etc. to receive plaster

M&L PCC 1:4:8, type D-2 (using 40 mm graded crushed stone aggregate) as in foundations filling and mass concrete complete all as specified and directed.

M&L Brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:6

S&F Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 including desmantling of old unserviceable staging/ laadders

S&F Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240 of Fe 410-W (Gde-E-250) quality-A

Excavation in post holes (or similar holes) each n.exc 0.50 cu.m getting out in any type of rocks, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm complete all as specified and directed.

M&L PCC 1:3:6, type C-1 (using 20 mm graded crushed stone aggregate) in foundations, filling and mass concrete

Providing, cement concrete as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones,bed plates slightly rounded or chamfered on edges Type B0 1:2:4 (using 12.5mm graded aggregate)

M&L for Cutting holes in stone walls built in lime mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required for depth exc one stone but n.exc two stones

S&F Pressed steel frames of size 105 x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc., complete, as specified

M&L Cement concrete Type BO 1:3:6 (12.5mm graded aggregate) as in filling for precast door frames

S&F 30mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides

S&F Powder coated aluminium window shutters, side hung type without sash bars including top fixed ventilator portion not more than 40cm in height, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified

S&F Powder coated aluminium frame for windows with one or more rebates including joining cleat for fixing etc. complete all as specified

S&F 4mm thick Sheet glass,ordinary quality and glazing with oil putty in square exc 0.5 sqm in each pane

S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing

S&F Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing

S & F Butt hinges, medium weight, cold rolled mild steel, and fixed of 100 mm size

All as per item No 119 here-in-before but 75mm size

S&F Mild steel barrel tower bolts, stove enamelled black, with bright bolt and fixed of 200mm long

All as per item No 121 here-in-before but 150mm long

S&F Mild steel pressed handles, oval type, stove enamelled black 150mm long

S&F Mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed of 300mm long

All as per item No 124 here-in-before but 250mm long

M&L Two coats of synthetic enamel paint on steel surfaces of any description, over 10cm in width or girth, over a coat of primer incl preperation of new surfaces all as specified

M&L Two coats of synthetic enamel paint on steel surfaces of any description, n.exc 10cm in width or girth, over a coat of primer incl preperation of new surfaces all as specified

M&L Two coats of synthetic enamel paint on wood surfaces of any description, over 10cm in width or girth, over a coat of primer incl preperation of new surfaces all as specified

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated/ plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa, 150 GSM as in roof covering/cladding to wall, fixed with self tapping screws as specified

Providing, cement concrete in roof kerbs or mud stops, rounded or chamfered on edges Type B0 1:2:4 (using 12.5mm graded aggregate)

M&L Rendering 10mm thick in CM 1:6 on fair faces of brick work or concrete surfaces finished even and smooth (without using extra lime or cement) all as specified and directed

M&L Rendering 15mm thick in CM 1:6 on fair faces of stone masonry surfaces or surface other than fair face of brick-work finished even and smooth (without using extra lime or cement) all as specified and directed

M&L Three coats of white wash incl preparing new plastered surfaces.

M&L Two coats of OBD over a coat of primer incl preparing new surfaces plastered or unplastered

M&L Two coats of cement based paint over a coat of primer incl preparing new surfaces plastered or unplastered

M&L Non - skid coloured Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15 mm thick screed bed in cement mortar 1:6

All as per item No 136 here-in-before but for area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm

M&L coloured Glazed ceramic tiles in vertical surface 350x 250x 7mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match complete over 10mm thick backing coat in CM 1:4 etc complete all as specified

M&L 25 mm thick Cement concrete type B-0, 1:2:4 (using 12.5mm graded stone aggregate)

M&L 100 mm thick Cement concrete type D-2, 1:4:8 (using 40mm graded stone aggregate)

S&F 3 layered rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I of capacity 250 L

S&F for 15mm bore tubes, medium grade, galvanised with and including all fittings fixed to walls, floors, or ceiling or laid in floors etc., complete all as specified and directed.

All as per item No 142 above but for 20mm bore

S&F in repair Bib taps, chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed to 15mm bore pipe

S&F in repair Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed to 15mm bore pipe

S&F in repair Vitreous China wash basin, white, flat back, size 550x400mm excluding taps but including brackets & waste coupling of PTMT (half or full threaded) (Minimum weight 32mm- 45gms/ 40mm-60 gms) for 32 mm bore

S&F in repair Vitreous China squatting pan, ‘Orissa’ pattern, size 550 x 400 mm white, with integral foot rests including provision of concrete bedding (excluding flushing cistern and flush pipe)

S&F 10 Ltr capacity PVC valveless syphonic action type flushing cistern, low level, coloured, with inlet, ball valve, float and handle including brackets and 32mm flush pipe and cones complete all as specified and directed.

S&F in repair Stop valves,fancy type, chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe and fixed to 15mm bore pipe

S&F PVC connections 15mm size with PTMT nuts of length 450mm

S&F PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to walls for 110mm bore

S&F PVC (SWR) 110 mm bore bends with access door complete all as specified and directed

Providing and fixing false ceiling with light weight 12mm thick mineral tiles of size 595x595mm suspended on silhouette profile suspension system of grid made from hot dipped GI steel section notary stitched double webbed power coated white consisting of main T- runner 42mmx14mm and 0.30mm thick and cross T of size 33mmx14mm and 0.30mm thick placed at 60cm centre having width of flange 14mm with a 6mm reveal profile (Blace). The grid system to be rested on the periphery wall/partitions on a W-profile wall section made of pre-coated galvanized steel of dimension 30mm long x (15mm+10mm)x22.5mm and laying false ceiling for services like diffusers grill including cutting, making opening for services like diffusers grill light fitting, fixture smoke detectors etc, wherever required main T-runner to be suspended from ceiling using GI suffix cleats of size 25mm x 35mm x 1.6mm fixed to ceiling with 6mm dia and 50mm long dash fastener, 4mm dia GI adjustable rods with galvanized level adjustment clips spaced as required, all complete at all height as per specification complete all as specified and directed.

Rendering 10mm thick CM 1:4 on fair faces of brick work or concrete as in internal wall surfaces finished even and smooth without using a extra cement

M&L for Precast reinforced cement concrete 1:2:4 type B1 using 20 mm graded stone aggregate as in cover slab for manholes set in CM 1:4 including necessary form work.

S&F TMT bars 10mm dia and above cut to length bent to shape required including cranking,bending,hooking ends and binding with MS wire (annealed) not less than 0.9 mm dia.

S&F MS round bar 10mm dia and over cut to length bent to shape required including cranking,bending,hooking ends and binding with MS wire (annealed) not less than 0.9 mm dia

M&L Brickwork with sub class ‘B’ bricks in one brick thick honey comb walling, built in cement mortar 1:4

Concrete bed to drain pipes including packing under and haunching against the sides of pipes with cement concrete 1:3:6 type C-2 after they are laid and tested,150 mm bore pipe.

Cement concrete 1:2:4 type B-1 (using 20mm graded stone aggregate) as in water troughs and coping.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete using extra cement, incl forms etc.

M&L Rendering 15mm thick in CM 1:6 on surface other than fair face of brick-work finished even and smooth (without using extra lime or cement) all as specified and directed

M&L Double corrugated pipes, DWCPE (SN8) pipes laid on PCC bed and jointed as specified and directed for Nominal size 150mm (ID 148.5/ od 172.5)

L and S ENTERPRISES

SANJEEV CONSTRUCTIONS

STANDARD AGENCIES

Srinivash Engineers

Universal refrigeration and Engineering Company

Srinivasa Consructions