PROVN OF TOILET AND URINAL IN GUARD POST OF DSC PERS AT DGIS AND CERTAIN REVENUE/MINOR WORKS UNDER AGE B/R-I AND AGE E/M OF GE (SOUTH) DELHI CANTT-10

Amount

Excavation in trenches n exc 1.5m in deepth and 1.5m in width and getting out in soft/loose soil complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25cm in hard/dense soil complete all as specified and as directed.

Removing excavated material (soil) n .exc 50m and deposited where directed at a level n exc. 1.5m above the strating point complete all as specified and as directed.

M&L for providing cement concrete 1:4:8 type D2 (Using 40mm graded stone agg) in foundation, mass concrete and filiingscomplete all as specified and as directed.

M&L Form work to side of concrete in fdns, footing base, base of columns, side and soffits of plinth beam and simillar work complete all as specified and as directed.

M&L for providing reinforcement cement concrete M-25 nominal mix as in footing, foundation,beams, plinth beams, base for columns and mass concrete etc complete all as specified and as directed.

M&L Form work to side of columns and simillar work complete all as specified and as directed.

M&L for providing reinforcement cement concrete M-25 (Nominal Mix) as in columns and pillars etccomplete all as specified and as directed.

M&L Form work to side of sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, and simillar work complete all as specified and as directed.

M&L for providing reinforcement cement concrete M-25 (Nominal Mix) as in Beams, cantilevers, ressummers, lintels over 1.5m span concrete etc complete all as specified and as directed.

M&L Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and as directed.

M&L Formwork to Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide complete all as specified and as directed.

M&L for providing reinforcement cement concrete M-25 (Nominal Mix) as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed.

S&F milt steel TMT bars 10 mm dia and over, cut to length, bent to shape requred, including crancing bending and binding with mild steel (anneal) wire not less than 0.90mm dia.

S&F milt steel TMT bars 8 mm dia in spacers, cut to length, bent to shape requred, including crancing bending and binding with mild steel (anneal) wire not less than 0.90mm dia.

S&F mild steel TMT5mm dia and over upto and including 10mm dia in stirrups, and binders complete all as specifed and directed.

Material & labour for brick work with sub class B old size burnt bricks straight or curved on plan exc 6m mean radius built in CM 1:4 complete all as specifie and directed

Material & labour for brick work with sub class B old size burnt bricks straight or curved on plan to any radius in half brick thick walls built in CM 1:4 complete all as specifie and directed

M&L Rendering 15 mm thick on fair faces of brick work or concrete surfaces with CM 1:6 finished even and smooth withot using extra cement.

M&L Rendering 15 mm thick on fair faces of brick work or concrete surfaces with CM 1:4 mixed with WPC finished even and smooth without using extra cement complete all as specifed and directed. (Note : WPC will be measured & paid separately).

Supply only Liquid water proofing compound of approved quality.

M & L for rendering 10 mm thick on surfaces of ceiling in cement mortar (1:3) and finished even and smooth without using extra cement complete all as specified and as directed.

Material & labour for preparation of new undecorated plastered surfaces of wall and applying three coats of white wash etc complete all as specified and as directed.

All as per item No 23 above, but in ceiling complete.

M&L Preparation of new plaster surfaces apply two coat of cement base paint over a coat of primer.

M&L hardcore of gauge n.exc. 63mm deposited, spread and levelled in layers n.exc 15cm thick watered and rammed to a true surface for plinth protection/path.

M&L for 75 mm thick Cement concrete 1:4:8 type D2 (using 40mm graded stone aggregate) as in sub base to floors finished even complete all as specified and directed.

M&L providing 25mm thick cement concrete 1:2:4 type B1 (Using 20mm graded stone agg) , as in sub base in floor/paving etc complete all as specified and directed.

M & L for joint free coloured non skid ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding. 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed with white or coloured cement to match over and including 15 mm thick screed bed of cement mortar (1:6) etc complete all as specified and as directed.

M&L coloured glazed ceramic tiles 300x450x6 to 7mm thick, in floors etc set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match the shade of tiles including rendering 10mm thick in CM 1:4 complete all as specified and directed.

M&L 75 mm thick cement concrete type C-2, 1:3:6 (40 mm graded aggregate) finishing cement concrete surface even and smooth without using extra cement as in plinth protection complete all as spd and directed.

S&F fibre glass reinforced plastic (FRP) door frame, three lagged of cross section 90 mm x 45 mm having single rebatd of 32x15 mm to receive shutter of 30 mm thickness, moulded withfire retardant grade unsaturated polyesterresin and chopped mat. Door frame laminateshall be 2mm thick and shall be filled withsuitable wooden block in all over frame. The frameshall be covered with fibre glassfrom all sides including MS stay at the bottom to steady the frame complete all as specified and directed.

S&F factory made solid FRP door shutter , 30 mm thick glass fibre reinforced plastic (FRP) panelled door shutter of required colour and approved brand and manufacture, made with fire retardantgrade unsaturated polyester resin mouled to 3 mm thick FRP laminated for forming hollow rails and styles iwthwooden frame and suitable blocks of seasoned wood inside at required places forfixing of fittings, cast monolithically with 5 mm thick FRP panels and confirmign to IS 14856-2000 complete all as specified and directed.

S&F 100mm long medium weight cold rolled mild steel butt hinges complete all as specifed and directed.

S&F Extruded Aluminium alloy handles, fabricated type anodised of 125mm long complete all as specifed and directed.

S&F Aluminium anodised barrel tower bolts of extruded section and fixed of 100mm long complete all as specifed and directed.

S&F 250 mmAluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specifed and directed.

M&L for Steel vantilator with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded.

M&L for 4.0 mm thick frosted sheet glass ordinary quality and glazing with oil putty in square n.exceeding 0.5 Sqm in each panes complete all as specifed and directed.

M&L for preparation of newly steel surface apply two coat of synthetic enamel paints over a coat of red oxide primer.

Supply & fixed in vitreous china wash down water closet (pedestal pattern) 'P' or 'S' trap including jointing including plastic water closet seat, closed pattern with flat bottom and cover and mild steel CP or aluminimised hinging device complete

S&F PVC valveless, syphonic action type flushing cistern, 10 ltr capacity,low level white with inlet ball valve, float and handle including bracket complete all as specifed and directed.

S&F Flushing pipe of polyethylene of low or high density or PVC, 32mm dia, for low level cistern complete all as specifed and directed.

S&F Vitreous China urinals, halft stall type, complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe.

S&F 15 mm bore CP Urinal spreader for urinals complete all as specified and directed

S&F vitreous china wash hand basin of size 550x400mm including cutting for and pinning in ends of brackets or erecting stand complete all as specifed and directed.

S&F in repairs PVC connection 15mm size, 450mm long with PTMP nuts both side complete all as specifed and directed.

S&F waste fittings, brass chromium plated for glazed ware sink, basins, etc with long screwed shanks and fly-nuts, flanged end bedded in red lead cement and other end fixed complete all as specifed and directed.

S&F rotational moulded polyethylene water storage tankof 500 ltr capacity (cylindrical vertical with closed top) hoisted and fixed in position all as specified and directed.

S&F ball brass valve high pressure with polythene float and fly nut complete screwed for iron pipe of size 20mm dia complete all as specifed and directed.

S&F bib taps fancy type chromium plated, with crunch or butterfly handle screwed down,screwed for iron pipe or for brass ferrule and fixed of 15mm bore size complete all as specifed and directed.

S&F pillar cock fancy typre cast copper alloy, chromium plated 15mm dia of bore complete all as specifed and directed.

S&F stop cock fancy type chromium plated, screwed down, high presure with cruntch or butterfly handle screwed both ends for iron pipe of 15mm bore pipe complete all as specifed and directed.

M&L 15mm GI tubing 'Medium grade' with all fiting and fixed complete tom wall and celing or laid in floor of fllowing sizes complete all as specifed and directed.

All as per srl item no 54 but 20mm bore complete all as specifed and directed.

S&F 100mm dia cast iron soil, waste and vent sand cast pipes in any length with or without ears, with cement joints, laid in trenches or in floors complete all as specifed and directed.

M&L for providing concrete bed to drain pipe including packing under and hauching against the sudes of pipes after they are laid and tested, in cement concrete 1:3:6 type C1 (Using 20mm graded stone aggregate) complete all as specifed and directed.

S&F 100 mm bore cast iron pipe (sand cast) as in soil, waste and vent pipe, in any length with or without ears, with cement joints fixed to walls, all as specified & directed.

M&LSalt-glazed stoneware gully traps, square or roun mouthed floor trap, plain with grating including jointing with solvent cement of 100mm dia complete all as specifed and directed.

S&F CP grating of size 100mm dia complete all as specifed and directed complete all as specifed and directed.

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in soft/loose soil complete all as specifed and directed.

S& F for machine pressed precast concrete interlocking paver block 60 mm thick any shape and size,with grey cement and pigment to match, confirming to IS 15658-2006 of 60mm thick M-35 grade laid over 50 mm thick sand cushioning.

M&L for PCC 1:4:8 type D-2 using 40mm graded stone aggregate as in surface channels & drain complete all as specified and as directed.

M&L for brick work with fly ash brick straight or curved on plan exc. 6M mean radius buit in CM 1:6 complete all as specified and as directed.

M&L for PCC 1:2:4 type Type B-0 using 12.5MM graded stone aggregates as in coping complete all as specified and as directed.

M&L for rendering 15MM thick in CM 1:4 on fair faces of bricks or concrete surfaces finished fair & even W/O using extra cement complete all as specified and as directed.

Extra for fair finished surfaces of drain inner girth 30cm in cement concrete,using extra cement,including forms,moulds,mitred/stopped ends etc.

M&L for provideing reinforcement cement concrete type B-1, M-25 (20mm graded aggregate) in precast drain cover only for 100 RM length complete all as specified and as directed.

S&F 100 mm bore salt glazed stoneware (SGSW) drain pipes laid in trenches and jointed as specified and connect to existing manholes including

M&L for 15mm thick cement plaster cement mortar (1:4) on fair faces of briick or concrete surfaces, finished fair & even without using extra cement complete all as specified.

S&F SFRC manhole cover size (1200 X 600 x 70 )mm thick with frame set in cement mortar 1:4 complete all as specified and as directed by Engineer-in-Charge. Notes: - (i) Make of SFRC Manhole/drain cover and frame : (a) M/s PS Concrete. (b) M/s KK Manhole.(c) Or equivalent as approved by GE” (ii) Contractor will provide manufactuerer test certificate of SFRC cover & frame

Taking down chowkhats or frames with shutter exc 1.5 sqm and nexc 2.00 sqm each but without taking off shutters from the frame incl removing.

All as per serial item No 72 here-in-before but nexc 1.5 sqm each

Dismantling wrought iron or mild steel work of any description not otherwise provided for windows grill.

S&F fabricated aluminum window with powder coated anodized aluminum frame of section 63.5mm x 38.10mm x1.5mm thick, shutter with section 47.62mmx44.45mmx1.5mm thick including aluminum anodized “D “ handle, hinges, peg stays, tower bolts, etc including jointing cleats for fixing builder's hardware fittings & stainless steel wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples including necessary fittings/fixture /aluminum snap beads complete all as specified. Note: Measurement shall be taken for clear opening i.e. out to out of window frame as a whole including all fittings and fixtures and no extra shall be paid separately.

M&L 6mm dia powder coated aluminium decco grill, (minimum thickness of powder coating 50 micron), section No-104, 100mm aperture of hexagonal design and pattern as approved complete all as specified and directed.

M&L powder coated aluminium anodised three way track sliding windows of frame size 92 mm x 31.75 mm x 1.5mm thickness (section no. 20831 of JINDAL) and of shutter size 40 mm x 18 (with 9.00 mm interlocking legs) x 1.45 mm thick (section no. 20737 of JINDAL) section (two shutter glazed, covering half of span of opening each & one shutter sketlon covering half of span of opening ) incl provn for making windows air tight, including 95mm aluminium handle with spring lock , stainless steel wire cloth, 0.45 mm nominal dia of wire and average width of aperature 1.4mm and fixed with steel wire stapples and 5mm thick plain glass including necessary fitting/ fixture/ aluminium snap beads complete all as specified. Note:- Measurement shall be taken for clear opening i.e. out to out of window frame as a whole including all fittings and fixtures and no extra shall be paid separately.

M&L for Granite (of any type) tiles 16 mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete and including 15mm thick screed bed in cm 1:6 for laying floor finish.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the primess.

M&L Coloured Dark shade vetrified ceramic tiles 8 mm thick (square / regtangular) polished , area of each tiles not exc 0.36 sqm in floors etc and joineted neat in cement slurry and pointed in white or colour cement to match over and including 15mm thick screed bed in CM 1:4 all as specified and directed.

All as per serial item No.81 above but on vertical surfaces such as skirtings, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10 mm thick plastering in CM 1:4 on brick masonry surfaces.

Taking down shutter of any description exc 1.00 sqm nexc 2.00 sqm each and refixing the same opening including easing and adjusting the same complete all as specified.

Taking down cement plaster on brick/concrete surface including racking out joints hacking for key scrubbing down with water etc.

M&L for Preparing new plastered surfaces of wall and applying two coats of distemper oil emulsion, over a coat white or tinted over & including a coat of wall care Putty complete.

M&L for preparation by complete removal of existing treatment, wahsing down and stopping of distempered and painted surfaces and old plastered or unplastered surfaces of wall and applying two coats of distemper oil emulsion, white or tinted over & including a coat of wall care putty complete all as specified and directed.

S&F in repairs brass CP Wall mixer for mixing Hot and cold water screwed down for iron pipe all as specified and directed.

S&F in repairs vitreous china wash hand basin, white round shape size 520x450x200 mm (excluding taps, waste, pipe chain and plug) but including porcelain stopper and a pair of MS bracket etc complete all as specified.

S&F in repairs vitreous china wash hand basin, white round shape size 520x450x200 mm (excluding taps, waste, pipe chain and plug) but including porcelain stopper and a pair of MS bracket etc complete all as specified.

S&F in repairs chromium plated brass angle valve suitable for 15mm bore pipe, complete all as specified.

M&L soap dish chromium plated brass fixed with brass nuts and screws as in repair complete all as directed

M&L toilet paper holder brass chromium plated as in repair complete all as specified and directed.

S&F in repairs CP brass shower rose fancy type 125mm size suitable for 15mm bore pipe complete all as specified.

S&F in repairs viterous china wash down water closet pan (Pedestal pattern) white incl 'P' or 'S' trap and making good the disturbed surface to match with the existing complete all as specified and as directed.

S&F in repair 12 mm thick prelaminatd particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work.

All as per serial item No 95 above but 18/19 mm thick.

Taking up or down 15mm bore steel tubing and connections complete all as specified and directed.

S&F in repairs (width of flaps 30 mm) Continuous (piano) hinges, mild steel, bright finish or electro galvanised

Cutting holes into or through brick wall bult in cement mortar or cement lime mortar and stone walls n.exc 150 sq.cm including making good to the original surface

Cutting chases, pining in making good to facing where required and pinting in cement to , cutting not exc 10cm girth in brick walls.

S&F steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St.-240 complete all as specified and as directed.

S&F Pre-printed galvalume aluminium zink coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screw/ L-type or J type cranked hook all as specified and directed.

S&F Structural Steel in roof, purlins crane of angle or other section gusset plates, Flat Iron rails braces etc, drilled for fixing, and other covering r etc to be prepared for hanging and sliding with and including either hooks and hinges and other covering running rails and guides and hanging also fastening and fixing complete. Fe- 410 Grade E-250 quality -Bl

M&L for cement Concrete Type B1 1:2:4( 20 mm Aggregate) in roof Kerbs or Mud stops,rounded or chamfered on edges.

Excavating in post holes in soft loose soil (or similar holes) each n exc 0.5 cu. m, getting out , returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm all as specified and directed.

Surface dressing not exceeding 15 cm deep and getting out in soft / loose soil complete all as specified.

M&L coloured Chequered cement concrete tiles 20cm x 20cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors including 20 mm thick screed bed in CM 1:4 complete all as specified and directed.

Removing of excavated material n exc 50 mtr and depositing where directed at a level n exc 1.5 mtr above the starting point.

Cutting holes into or through brick wall bult in cement mortar or cement lime mortar and stone walls n.exc 150 sq.cm including making good to the original surface

M&L for preparation of newly plastered surfaces on external wall/ ceiling, applying two more coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/ litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance eterior paint of required shade(Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 Sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 Sqm.complete and including 2 mm thick water proof wall care putty complete all as specified and as directed.

Dismantling boarding, any description, fixed in any position with nails or independent self tapping complete all as specified and directed.

S&F factory made single extruded WPC (Wood Polymer Composite) solid frames or chowkhat of size 45 x 75 mm comprising of vigin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ricehusk/wheat husk) and non toxicadditives (maximum toxicity index of 12 for 100 g,s) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of class A category with property of being termite/ borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge Note:- For WPC solid frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

M&L for 18 mm thick wood plastic composites (WPC) board for shutters, shelves with property of being termite/ borer proof, water/ moisture proof and fire retardant 100% solid with density not less than 650 Kg per cubic meter , one side wood grain finished laminated for exposed/external surface , fixed with screws fitted under or above the kitchen cooking platform including all necessary fittings and fixtures like nickle plated clip pieno hinges, knobs, channels etc complete all as specified and directed. Note : (a) Pattern & design of WPC board to be decided by GE

S&F for PVC magnetic door catcher of kitchen cabinet and similar work fixed with MS screws complete all as specified and as directed.

M&L for treatment of soil under existing floor through above the skirting using emulsion Termin or equivalent Anti Termite Treatment making the holes @300 mm center to center along the internal wall, 50mm deep including drilling and plugging 12mm dia holes with sealed coloured cement to match the existing skirting of the wall complete all as specified and as directed.

M&L for treatment of existing floors spray with pressure gun machine using emulsion Termin or equivalent Anti Termite Treatment complete all as specified and as directed. Notes for Srl item Nos.115.00 & 116.00:- (i) The work of anti termite treatment shall be got executed by the contractor through an approval agency (as approved by the GE) who is a member of PCAI (Pest Control Association of India) holding valid license as per clause 12 of insecticides Act, 1968 and persons employed to do the antitermite treatment shall be qualified as per Rule 10 of the Rules framed under insecticides Rules 1991 (ii) The contractor shall stand guarantee to the Government for a period of 10 years from the certified date of completion of work. The contractor shall furnish a written guarantee for the effectiveness of the treatment for a period of ten years in favour of GE. (iii) 2.5% of work done amount of this item shall be retained from contractors payment for a period of 10 years reckoned from date of physical completion of this work, or in lieu contractor may deposit bank FDR for the said amount for 10 years which shall be released.

S & F rolled mild steel work as in post and struts in fencing including cutting tops to shape as directed, drilling holes,notching for wire etc, flat iron fillets( for escuring wire mesh etc.) including all necessary drilling, bolting or riveting etc and similar work conforming to GDE Fe 410-0 or Fe 310-0 complete all as specified and as directed.

S & F rolled mild steel work as in framed barred iron gates including all necessary drilling, bolting or riveting etc and similar work conforming to GDE Fe 410-0 or Fe 310-0 complete all as specified and as directed.

S & F 5-10mm dia of shank mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, n exc 5cm long complete all as specified and as directed.

Supply only chain link MS galvanised fencing, any size or type all as specified.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, strainig bolts, etc. including provision of binding wire complete all as specified.

M&L for point wiring multi stranded complete, stranded copper conductor 1.5 Sqmm nominal area PVC insulated FRLS 1100 volts grade electrical cable in through suitable concealed PVC conduit including modular sunken pressed steel terminal boxes 2mm thick of required size and modular white cover plate with all accessories including 1.5 sqmm multi stranded copper conductor PVC unsheathed cable earth wire to common earth and connected to earth dolly complete all as specified and directed . Note :- At roof slab where there is burnt/blockage in the existing conduit wiring will be done through PVC conduit and rate are inclusive in above quoted item. (a) One light /fan/Bell point/security light controlled by one way switch

All as per srl item No 122 here in before but One 3 pin socket outlet 5 amps point same board

All as per srl Item No 122 here in before but for one socket outlet 15 Amps on Independent board with cables 2.5 sqmm size for phase and neutral and 2.5 Sqmm for earthing complete.

S&F of Switch modular type, 1Module, 6 Amps one way complete all as specified and directed.

S&F of Socket outlet modular type 2M, 3 pin, 6 Amp complete all as specified and directed.

S&F of Socket outlet modular type 2M, 3 pin, 6 Amp complete all as specified and directed.

S&F of Switch modular type 1M, 16 Amp with red indication light complete all as specified and directed.

S&F ceiling rose surface Bakelite 65x25mm two to three terminals complete all as specified and directed.

S&F of LED Integrated Batten T5 20 Watt - 4Ft White, indoor decorative PVC extruded T5 LED complete all as specified and directed.

S&F of LED Integrated Batten T5 10 Watt - 2Ft White, indoor decorative PVC extruded T5 LED complete all as specified and directed.

S&F LED street light fitting 40 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver complete all as specified and directed.

S&F of GI bracket of suitable size for fixing of LED security light fitting, bracket of 25mm dia is atleast 1.5 mtr long to be fixed on pole and it has to be bend in 45 degree angle to install the LED security light fitting including necessary welding work and MS fastner, clamp with strip complete all as specified and directed.

M&L for opening of hole through out the wall as suitable for exhaust fan of size 300mm sweep and fixing of nut-bolts with 4" anchor fastner of suitable size and making food the disturbed surface and all as per site requirement complete all as specified and directed. Note : The rates are inclusive in respect of under this item as above hole opening civil work with MS faster bolt of 8mm dia and 100mm (minimum) long for fixing of exhaust fan and MS fastner clamps strip 38 mm wide and 5mm thick (min) to hold exhaust fan.

S&F of metal body exhaust fan 300 mm sweep, 230 Volts with louver and copper wound including necessary electric connection with appropriate size of PVC copper wire from ceiling rose/switch board to exhaust fan including fixing of nut-bolts of suitable size and making good the disturbed surface of wall with OBD/White wash to match with complete all as specified and directed.

S&F MCB DB SPN 4 Way with metal double door, (IP43 Protection) flush mounting epoxy powder control having 200 Amps rated bus bar complete all as specified and directed.

MCB SPN 'B' curve 40 Amps 240 Volts, 10 KA complete all as specified and directed.

S&F MCB SP 'B' curve 06 to 32 Amps 240 Volts complete all as specified and directed.

M&L for Earthing complete with galvanized steel earth plate 600x600x6mm thick, buried directly in ground (earth pit not less than 2.25 m deep below ground level) with top edge of the plate n.less than 1.5 m below normal ground level, connected to galvanized iron wire 4 mm as earthing lead by means of bolts, nuts, check nuts & washers of galvanized iron or steel besides building at all joints as shown in drgs and including excavation and earth work, GI pipe light grade 25mm bore of protection of GI wire from earth electrode, supply and laying charcoal dust, common salt, PCC (1:2:4) type B-1 Chamber and MS angle iron frame 40x40x3mm and RCC cover 40 mm thick (1:2:4) type B-1using 20 mm graded stone aggregate Reinforced with 6 mm dia round bars @ 75 mm C/C both ways with MS handle 12 mm dia , PGI funnel and wire mesh, 20 mm dia GI Pipe light grade for watering complete all as shown in drg and connected to earth test point including testing complete all as specified and directed.

S&F of 25mm galvanised pipe medium grade lain in trenches/walls including fitting complete all as specified and as directed.

Supply and fix Valve, stop, screwed, 25mm (1") dia pipe all complete all as specified and as directed.

M & L for cutting existing 50/80/100mm dia GI pipe and threading inserting TEE 50/80/100 x 50/80/100 x 25 mm including all fittings such as union, socket etc making leakage proof joints using gasket etc all complete all as specified and directed by Engr-in-Charge.

Supply, laying and testing cable XLPE insulated screened PVC badded, galvanised steel stip armoured, electric power bable (heavy duty) 1100 volt grade with stranded aluminium onductor of size 10 Sqmm, 2 Core completed all as specified and as directed.

Supply and laying Double Wall Corrugated (DWC pipe in excavation of tranched of 25 mm size including all connecting necessary items complete all as specified and as directed.

Supply and laying including taking out G.I tubing light grade for encasing Lt cable for mechanical protection, laid under plinth/floor/roads/ paths/culverts or fixed on walls or concealed in walls or along the steel poles incl bends/clamps and all accessories complete all as specified size of 25 mm bore

Supply and laying XLPE insulated armoured cable (heavy duty) electric cable with aluminium stranded conductor 1100 volts grade of following size after taking down including cable jointing kit complete all as specified and directed by Engr-in-charge and directed as follows :

(a) 50 Sqmm x 3.5 Core

(b) 70 Sqmm x 3.5 Core

(c) 95 Sqmm x 3.5 Core

(d) 185 Sqmm X 3.5 Core

(e) 300 Sqmm x 3.5 Core

Taking down unservicable LT panel from inside the building including and cable disconnection of all electrical connection making good distrubed surface with CM 1:3 and same surface finishes with the adjoining surface of distribed area with ODB/colour wash/white wash complete all as specified and directed by Engr-in-charge.

Supplying, installation, testing and commissioning LT panel 3.15 mm thick of stainless steel of 304 grade cubical outdoor type weather proof, totally enclosed with IP 65 protection made out of CRC sheet angle iron of size 40 mm x 40 mm x 6 mm suitable for 3 phase, 4 wire ,440 volts, 50 Hz including cable glands, phase indicators, internal wiring,CT of suitable Ratio, voltmeter, ammeter, air passing holes with proper spacing to accommodate to all control switches and other accessories including on load changeover, cable connections with suitable size of lugs/thimble etc and locking arrangement with two locks godown type welded inside of the shutter with duplicate keys, spray painting with two coats of light gray paint over a coat of red oxide primer and mounted on two No bricks pillars including excavation and earth work complete PCC (1:2:4) brick work (1:4) and plastering complete.

Supply & Fixing of sheet metal enclosure V TPN 4 way MCCB 125A, 4P, Double door DB, IP-54, bus bar, neutral link earth bar and din rail complete all as specified and directed.

Supply & Fixing in replacement of on distribution board MCCB 125 Amps, 4 Pole, 415 Volts with 16 kA including electrical connection with bus bar or incomer with appropriate size of aluminium lugs and insulation packing includign suitable size of thimble complete all as specified and directed .

S&F sheet metal enclosure of size 350 x 300 x 150 mm suitable for mounting electronic meter fabricated from CRCA sheet with anti corrosive dust and vermin proof complete all as specified and directed by Engr-in-Charge. Note :- The meter cover shall have a transparent window. The window shall be of transparent, high grade UV stabilizer engineering plastic for easy reading of all the displayed values/parameters and observation of operation indicator. The window shall preferably be an integral part of meter cover.

S&F for MCB SP 40/63 Amps 240 Volts, 10 KA, `B' curve, including suitable size of thimble complete all as specified and directed.

M&L for earthing in replacement complete with GI earth plate electrode 600 x 600 x 6mm thick burried directly in ground in ground (earth pit plate kess than 2.5 mtrs below ground level) with top edge of the plate not less than 1.5 mtrs deep below normal ground level, connected to galvanised earth wire 4mm by means of bolts, nuts check nuts to earth test point including necessary PCC 1:2:4 type B-1 pit, cover frame, GI pipe 15mm dia light grade with funnel and locking arrangement complete all as specified and directed.

M&L in replacement of Earth continuity conductor or main earthing lead in replacement fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicate dsituation for loop earthing etc. as required 4mm dia galvanised iron or steel wire

M&L for earthing in replacement complete with GI earth plate electrode 600 x 600 x 6mm thick burried directly in ground in ground (earth pit plate kess than 2.5 mtrs below ground level) with top edge of the plate not less than 1.5 mtrs deep below normal ground level, connected to galvanised earth iron strip 32x6mm by means of bolts, nuts check nuts to earth test point including necessary PCC 1:2:4 type B-1 pit, cover frame, GI pipe 15mm dia light grade with funnel and locking arrangement all as specified and directed.

Supply and laying of Double Wall Corrugated (DWC Pipe in excavation of tranched of 150mm size including all connecting necessary items complete all as specified and as directed.

Supply and laying Double Wall Corrugated (DWC Pipe in excavation of tranched of 100mm size including all connecting necessary items complete all as specified and directed.

Boring holes under road pavement by bocky manually in any type of soil upto 50 mm bore complete all as specified and directed by Engr-in-Charge.

Note :- The contract sum shall be after deducting the amount of credit shown in Sch of Credit of this tender

JINDAL ENTERPRISES (BID ID -3100955)

M/S Parmod Johar (BID ID -3103894)