State Taxes and Excise Department at Solan

Amount

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding upto all depth, all width as well as area on plan) including getting out and disposal of excavated earth through mechanical means up to all lead/lift, loading/unloading including dumping charges as directed by Engineer-in-charge. All kinds of soil

Excavation work by mechanical means (Hydraulic excavator)/ manual means in foundation trenches or drains (upto all width or area on plan), including dressing of sides and ramming of bottoms, upto all leads and lifts, including getting out the excavated soil and disposal of surplus excavated soils as directed, with all leads and lifts. Ordinary rock

Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (up to all depth & width as well as all area on plan) including getting out and disposal of excavated earth upto all leads and lifts as directed by Engineer-incharge., when required into plinths, sides of foundations etc. consolidating each deposited layer by ramming and watering and then disposing off all surplus excavated earth with all leads and lifts as directed by the Engineer-in- charge. Ordinary/Hard rock(blasting probiited)

Excavating trenches of required width for pipes, cables,etc including excavation for sockets, and dressing of sides, ramming of bottoms, upto all depth including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including onsolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, with all lead and lift.

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (upto all width or area on plan), including dressing of sides and ramming of bottoms, upto all lifts, including getting out the excavated soil and disposal of surplus excavated soil as directed, with all lead and lifts. All kinds of soil

Filling in plinth with sand under floors includingwatering,ramming,consolidating and dressing complete including cost of sand including carriage of material in all leads and lifts..

Centering and shuttering including strutting, propping etc. and removal of form including carriage of material in all leads and lifts.

Foundations, footings, bases of columns,etc. for mass concrete

Suspended floors, roofs, landings, balconies and access platform

Columns, Pillars, Piers, Abutments, Posts and Struts

Stairs, (excluding landings) except spiralstaircases

Lintels, beams, plinth beams, girders,bressumers and cantilevers

Edges of slabs and breaks in floors and walls

Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

Weather shade, Chajjas, corbels etc., including edges

Retaining walls, return walls, walls (any thickness) including attached pilasters, buttresses, plinth and string courses fillets, kerbs and steps etc.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering including carriage of material in all leads and lifts.

1:4:8 (1 Cement : 4 coarse sand) : 8 graded stone aggregate 40 mm nominal size)

1:2:4 (1 Cement : 2 coarse sand : 4 graded stone aggregate 40 mm nominal size)

Providing and laying cement concrete in retaining walls,return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five level, excluding the cost of centering, shuttering and finishing including carriage of material in all leads and lifts 1:3:6 (1 Cement : 3 coarse sand): 6 graded stone aggregate 40 mm nominal size)

Providing and laying cement concrete 1 : 6 : 12 (1 cement : 6 sand :12 graded stone aggregate 40 mm nominal size) and curing complete excluding cost of form work in foundation and plinth including carriage of material in all leads & lifts.

Providing and laying cement concrete 1 : 8 : 16 (1 cement : 8 sand :16 graded stone aggregate 20 mm nominal size) and curing complete on slab and floor excluding cost of form work screed laid under flooring including carriage of material in all leads & lifts.

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement including carriage of material in all leads and lifts. All work up to plinth level

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills,staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand) : 3 graded stone aggregate 20 mm nominal size) including carriage of material in all leads & lifts.

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement 1:1.5:3 (1 cement : 1.5 coarse sand) : 3 graded stone aggregate 20 mm nominal size) including carriage of material in all leads & lifts.

Providing and laying up to floor five level reinforced cement concrete in kerbs, steps and the like excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand) : 3 graded stone aggregate 20 mm nominal size) including carriage of material in all leads & lifts.

Smooth finishing of the exposed surface of R.C.C. Work with 6 mm thick cement mortar 1:3 (1 Cement : 3 fine sand) including carriage of material in all leads & lifts.

Applying cement slurry on R.C.C . slab or cement concrete work using 2.75 kg of cement per sqm. of floor area before laying cement concrete flooring including roughening, cleaning of the concrete surfaces complete including carriage of material in all leads and lifts.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level / above plinth level including carriage of materialin all leads and lifts.

Brick work using 2nd class common burnt clay building bricks in foundation and plinth in cement mortar 1:4 (1 cement : 4 sand) including carriage of material in all leads and lifts.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in Cement mortar 1:6 (1 cement : 6 coarse sand)including carriage of materialin all leads and lifts.

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level Cement mortar 1:4 (1 cement :4 coarse sand) including carriage of material in all leads and lifts.

Brick work 7 cm thick with common burnt clay F.P.S. (non modular) brick of class designation 7.5 in cement mortar 1:3 (1 cement : 3 coarse sand) in superstructure above plinth level and upto floor five level including carriage of material in all leads & lifts.

Providing and fixing PVC pipe of ISI market 100 mm. dia for weep holes in brick masonry / stone masonry/ reinforced cement concrete R/wall, including carrage of material in all leads &lifts.

Stone filling behind retaining walls including carrage of material in all leads &lifts.

Providing wood work in frames of doors, windows, clerestory windows and other frames wrought, frames and fixed in position including carriage of material in all leads and lifts.(a) Ivory coast teak Wood

Providing wood work in frames of false ceiling, partitions etc. sawn and fixed in position with necessary stainless steel screws etc including carriage of material in all leads & lifts. Sal wood

Providing and fixing 35 mm thick panelled door shutters made of 1st class ivory coast teak wood having styles and top rail 100 mm width and bottom rail 200 mm width, lock rail 150 mm width with pannel insert of 12 mm thick, both side laminated board of approved manufacturer ISI mark, 1st class ivory coast teak wood chamfered beading 40.x12 mm size along the pannels on both side faces of shutter and providing wooden cleats and ISI marked black enamelled M.S. butt hinges with necessary screws all complete as per drawing and specification and instructions of Engineer-in-charge including carriage of material in all leads and lifts.

Providing & fixing 35mm thick single/double leaf fully glazed window shutters made of 1st class ivory coast teak wood having styles & top rail & bottom rail 75mm width and chamferred edged beading 20x12mm for glass panes complete including bright finished/black enamelled iron butt hinges with necessary screws including carriage of material in all leads and lifts.

Providing and fixing 35mm thick wire guage shutters using galvanised M.S guage of I.S.guage designation 85 G with wire of dia 0.56mm for doors, windows & clerestory windows including bright finished black enamelled iron butt hinges with necessary screws etc I/c chamfered edged beading 20x12.5mm size.complete including carriage of material in all leads .and lifts. (a) 1st class ivory coast Teak wood.

Providing and fixing 2nd class teak wood plain lining tongued and grooved, including wooden plugs complete with necessary screws and priming coat on unexposed surface including carriage of material in all leads & lifts 12 mm thick

Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size) including carriage of material in all leads and lifts

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete including carriage of material in all leads & lifts. Fixed to openings /wooden frames with rawl plugs screws etc.

Providing and fixing stainless steel sliding door bolt transparent or dyed to required colour and shade with bolts, nuts and screws etc. complete including carriage of material in all leads & lifts.

Providing and fixing stainless steel tower bolt (barrel type) annodized transparent or dyed to required shade and colour with screws etc. complete including carriage of material in all leads & lifts.

Providing and fixing stainless steel handles annodized transparent or dyed to required colour or shade with necessary screws etc. complete including carriage of material in all leads & lifts.

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete including carriage of material in all leads and lifts.

Providing & fixing Stainless steel hook & eyes with necessary screws or welding to chowakat including carriage of material in all leads and lifts.150mm.

Providing and fixing Stainless steel floor door stopper with necessary screws etc. complete including carriage of material in all leads and lifts.

Providing and fixing bright finished brass 100 mm mortice latch and lock, ISI marked, with six levers and a pair of anodised (anodic coating not less than grade AC 10 as per IS : 1868) aluminium lever handles of approved quality with necessary screws etc. complete including carriage of material in all leads &lifts.

Providing and fixing cup board shutters with 25 mm thick veneered particle board IS : 3097 marked, exterior grade (Grade I), of approved make, including IInd class teak wood lipping of 25 mm wide x 12 mm thick with necessary screws and bright finished stainless steel piano hinges, complete as per direction of Engineer-in- Charge including carriage of material in all leads &lifts. With decorative veneering on one side and commercial veneering on other side

Providing and fixing Pre-laminated medium density fibre board IS: 14587:1998 marked, with one side decorative lamination other side balancing lamination Grade-I(exterior grade) in shelves with screws and fittings wherever required, edges to be sealed with PVC edge bending tape 2.00 mm thick of approved brand (fittings to be paid separately) including carriage of material in all leads &lifts. Pre-laminated with decorative lamination one side and other side balancing lamination exterior Grade - I MDF Board 18 mm thick confirming to IS:14587

Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality including carriage of material in all leads &lifts. 1.0 mm thick

Providing and fixing cupboard lock with necessary screws etc. Complete including carriage of material in all leads &lifts.

Providing and fixing magnetic catcher of approved quality in cupboard / ward robe shutters, including fixing with necessary screws etc. complete including carriage of material in all leads &lifts. Triple strip vertical type

Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete including carriage of material in all leads &lifts. 2nd class teak wood 50x12 mm

Supplying and fixing expended metal to wood or steel members in partitions etc Weight not exceeding 3 kg.per square metre including carriage of material in all leads & lifts.

Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2 mm and braced with flat iron diagonals 20x5 mm size, with top and bottom rail of T-iron 40x40x6 mm, with 40 mm dia steel pulleys, complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of approved steel primer including carriage of material in all leads and lifts

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete i/c cutting the tiles wherever required including carriage of material in all leads &lifts. Size of Tile 600x600 mm

Providing and laying Vitrified tiles in different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS: 15622, of approved brand & manufacturer, in all colours and shade, in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately) including carriage of material in all leads & lifts. Size of Tile 600x600 mm

Providing and fixing 10 mm thick acid and/or alkali resistant tiles of approved make and colour using acid and/or alkali resisting mortar bedding, and joints filled with acid and/or alkali resisting cement as per IS : 4457, complete as per the direction of Engineer-in- Charge including carriage of material in all leads & lifts. In dado/skirting on 12 mm thick mortar 1:4 (1 acid proof cement : 4 coarse sand) Acid and alkali resistant tile

Providing and fixing Ist quality ceramic digital glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge i/c cost for cutting the tiles whwrever required, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete including carriage of material in all leads & lifts.

Providing and fixing 8 to10 mm thick HD digital porcelain tiles for treds / riser of stair case in single piece of approved make and colour using acid and/or alkali resisting mortar bedding, and joints filled with acid and/or alkali resisting cement as per IS : 4457, complete as per the direction of Engineer-in- Charge including carriage of material in all leads & lifts. In treds / risers of staps on 12 mm thick mortar 1:4 (1 acid proof cement : 4 coarse sand) size for steps 300x900mm and in Riser 200x900mm

Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in- Charge. including carriage of material in all leads & lifts. 60mm thick cement concrete paver block of M-35 grade with approved colour, design & pattern.

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge including carriage of material in all leads and lifts.Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

Providing and fixing chromium plated brass curtain rod having wall thickness of 1.25mm with two chromium plated brass brackets fixed with C.P. Brass screws and PVC sleeves etc., wherever necessary complete including carriage of material in all leads and lifts. 20 mm dia

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in- charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). including carriage of material in all leads and lifts.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required including carriage of material in all leads and lifts.

Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete including carriage of material in all leads and lifts.

Ridges or hips (500-600mm) plain (500 - 600mm)

Flashings/ Aprons.( Upto 600 mm)

Gutter/valley (600 mm over all girth)

Providing and fixing M.S. BP Sheet 1.66mm to 2mm thick in eaves board/facia/soffits/ ceiling including cutting, fixing and welding to steel roof members and applying a coat of red lead primer complete as per the instruction of Engineer-in-charge (Base members of steel work shall be measured & paid separtely) i/c carriage of material in all leads and lifts.

Providing and fixing polycarbonatd tranparent sheet 1.20mm thick in roofing with alvanised J or L hooks bolts and nuts with G.I. Limpet and bitumen rubber washer omplete with all accessories as required as per direction of Engineer-in-Charge including carriage of material in all leads and lifts.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete including carriage of material in all leads and lifts Hot finished welded type tubes

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes i/c carriage of material in all leads and lifts. 110 mm diameter

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion i/c carriage of material in all leads and lifts

Bend 87.5° 110 mm bend

Shoe (Plain) 110 mm Shoe

Providing and fixing M.S. holder bat clamps of approved design to PVC / C.I. or S.C.I. rain water pipes embedded in and including cement concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) and cost of cutting holes and making good the walls etc including carriage of material in all leads and lifts. 100 mm diameter

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required including carriage of material in all leads and lifts.

In stringers, treads, landings etc. of stair cases, including use of chequered plate wherever required, all complete

In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

Providing and fixing M.S.round holding down or anchor bolts with nuts and washer plates complete including carriage of material in all leads and lifts.

Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications including carriage of material in all leads and lifts. Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/ 10 sqm over an under coat of primer applied @ 0.80 ltr/10 sqm of approved brand and manufacture

French spirit polishing Two or more coats on new works including a coat of wood filler including carriage of material in all leads and lifts.

6 mm cement plaster to ceiling of mix 1:3 (1 cement : 3 fine sand) including carriage of material in all leads and lifts.

12 mm cement plaster finished with a floating coat of neat cement of mix1:4(1cement :4sand) including carriage of material in all leads & lifts.

15 mm cement plaster on the fair side of single or half brick wall of mix 1:4 (1 cement: 4 fine sand) including carriage of material in all leads and lifts.

20 mm cement plaster on the rough of single or half brick wall of mix 1:4 (1 cement: 4 fine sand) on rough side wall including carriage of material in all leads & lifts.

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete including carriage of material in all leads and lifts

Finishing walls with 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives New work (Two or more coats applied @1.43 litre/ 10 sqm. Over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm.including carriage of material in all leads and lifts.

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade New work (two or more coats) over and including water thinnable priming coat withcement primer including carriage of material in all leads and lifts.

On Wall

On Ceiling.

Providing and fixing 40mm nominal bore galvanised M.S. Tube(light grade) out let in cement mortar 1:3(1 cement: 3 Sand) including carriage of material in all leads and lifts.

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone - III) : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth including carriage of material in all leads & lifts.

Extra for laying concrete in or under foul positions including carriage of material in all leads & lifts.

Constructing Course rubble hammer dressed 'U' shape open surface drain with side wall. 15x22 cm in cement mortar 1:6 (1 Cement : 6 Sand) and inside plastring with cement plaster 1:3 (1 Cement:3 Sand) including earth work and laying 10 cm cement concrete in 1:5:10 (1 Cement : 5 Sand : 10 graded stone aggregate) of 40 mm nominal size) and 7.5 cm cement concrete 1:2:4 (1 Cement : 2 Sand : 4 Graded stone aggregate of 20 mm nominal size) and finished with a floating coat of neat cement complete as per standard design Including carriage of material in all leads and lifts.

Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections Including carriage of material in all leads and lifts.

Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7kg per square metre on damp proof course after cleaning the surface with brushes and finally with apiece of cloth lightly soaked in kerosene oil Including carriage of material in all leads and lifts.

Brick edging in full brick width and half brick depth including excavation, refilling and disposal of surplus earth lead upto 50 metres.. including carriage of material in all leads and lifts. With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing and fixing precast Cement concrete kerb stone size 45x23x7.5 Cm vertically with cement mortar 1:3 (1 cement : 3 sand) in parking as per direction of Engineer-in-Charge including carriage of material in all leads and lifts

Providing and fixing G.I. Pipes complete with G.I. fittings and clamps, i/c making good the walls etc. concealed pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall including carriage of material in all leads and lifts. 15 mm nominal bore

Providing and fixing G.I. pipes complete with G.I. Fittings including trenching and refilling etc including carriage of material in all leads and lifts.

15 mm nominal bore

20mm nominal bore

Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee,including cutting and threading the pipe etc. complete including carriage of material in all leads and lifts. 25 to 40 mm nominal bore

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank Including carriage of material in all leads & lifts. 1000 litres net capacity storage tank of ISI marked sintex make with double.layer including MS Stays for water storage tank.

Providing and fixing high pressure PVC spigot and socket soil, waste and ventilating pipe ISI marked i/c fixing with approved adhensive (i/c PVC clips where ever required) including carriage of material in leads and lifts.

90mm nominal size.

110mm nominal size.

150mm nominal size.

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete including carriage of material in all leads and lifts.

Providing and fixing PVC Plain bend ISI marked complete i/c fixing with approved adhensive etc complete including carriage of material in all leads and lifts

90mm nominal size.

110mm nominal size.

150mm nominal size.

Providing and fixing PVC door bend with oval access door, insertion rubber washer 3 mm thick bolts and nuts ISI marked complete including fixing with approved adhesive etc.complete including carriage of material in all leads and lifts

90mm nominal size.

110mm nominal size.

P/F PVC Single equal branch ISI marked of required degree with oval access door insertion rubber washer 3mm thick bolts and nuts complete i/c fixing with approved adhensive etc complete including carriage of material in all leads and lifts

90mm nominal size.

110mm nominal size.

Providing and fixing PVC Collar i/c fixing with approved adhensive etc complete including carriage of material in all leads and lifts

90mm nominal size.

110mm nominal size.

150mm nominal size.

Providing and fixing (ISI marked) PVC cowl i/c fixing with approved adhensive etc complete including carriage of material in all leads and lifts.

90mm nominal size.

100mm nominal size.

110mm nominal size.

Providing and fixing (ISI marked) PVC floor trap of self cleaning design i/c fixing with approved adhensive with C.P. screwed down or hinged grating with or without vent arm complete including cost of cutting and making good the walls and floors including carriage of material in all leads and lifts.110x90 mm

Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required including carriage of material in all leads and lifts.

White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer

460mm dia (countertop)

Providing and fixing uplasticised PVC connection pipe with brass unions including carriage of material in all leads and lifts. 45 cm length 15 mm nominal bore

Providing and fixing C.P. Connection pipe with brass Union including carriage of material in all leads and lifts. 45 cm length 15 mm nominal bore

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete Including carriage of material in all leads and lifts. Flexible pipe

32mm nominal bore

40mm nominal bore

Providing and fixing M.I Union for Wash basin & Sink Including carriage of material in all leads and lifts.

32mm nominal bore

40mm nominal bore

Providing & fixing C.P. brass waste for wash basin or sink including carriage of material in all leads & lifts.

32mm nominal bore

40 mm nominal bore

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required Including carriage of material in all leads and lifts. 510x1040 mm bowl depth 250mm with drainage board

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete Including carriage of material in all leads and lifts.

Providing and fixing C.P. brass towel rail complete with C.P. Brass brackets fixed with Plastic Gitti, drilling hole, C.P. brass screws etc complete in all respects including carriage of material in all leads and lifts.600mmx20 mm

Providing and fixing C.P. Brass towel ring fixed with Plastic Gitti, drilling hole, C.P. brass screws etc complete in all respects including carriage of material in all leads and lifts.

Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc. Complete including carriage of material in all leads and lifts.

Providing and fixing floor mounted, white vitreous china single piece, double traps syphonic water closet of approved brand/make, shape, size and pattern including integrated white vitreous china cistern of capacity 10 litres with dual flushing system, including all fittings and fixtures with seat cover, cistern fittings, nuts, bolts and gasket etc including making connection with the existing P/S trap, complete in all respect as per directions of Engineer-in-Charge including carriage of material in all leads and lifts.

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required including carriage of material in all leads and lifts. W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing 8 mm dia C.P. / S.S. health faucet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge including carriage of material in all leads and lifts.

Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet including carriage of material in all leads and lifts. 150 mm diameter

Providing and fixing C.P. brass bib cock of approved quality conforming to IS standards and weighing not less than 690 gms..15mm dia Including carriage of materia in all leads and lifts.

Long Body

Short Body

Providing and fixing 15 mm C.P. mixer for kitchan sink with top/ bottom swinging spout Including carriage of material in all leads and lifts.

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 Including carriage of material in all leads and lifts.15mm nominal bore

One Way Angle cock

Two way angle cock

Providing and fixing 100 mm dia chromium plated grating of superior quality for floor, gully or nahani trap i/c carriage of material in all leads & lifts.

Providing and fixing brass full way valve with wheel Including carriage of material in all leads and lifts.

15mm nominal bore

20mm nominal bore

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) Including carriage of material in all leads and lifts.

15mm nominal bore

32mm nominal bore

Cutting holes through existing brick work including making good the same in cement mortar 1:6 (1 cement: 6 sand) per CMs depth of cutting (i) Holes upto and including 400 sqcm in area including carriage of material in all leads and lifts

Providing chases 75mm wide 50mm deep (average size) in walls for conduit pipes and filling the same with cement concrete 1:3:6 (1 Cement : 3 Sand : 6 Graded stone aggregate 20 mm and down gauge) after the conduit pipe is laid (excluding the cost of conduit pipe) including carriage of materialin all leads and lifts.

Providing and fixing square-mouth SW gully trap Class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mmsize (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design including carriage of material in all leads and lifts. 100x100 mm size P type With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Constructing masonry Chamber 60x45x50 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for water meter complete with C.I. double flap surface box 400x200x200 mm (inside) with locking arrangement and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) , i/c necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand:10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design including carriage of material in all leads and lifts. With common burnt clay F.P.S.(non modular) bricks of class designation 7.5

Constructing masonry Chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size ) , i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design including carriage of material in all leads and lifts. With common burnt clay F.P.S.(non modular) bricks of class designation 7.5

Providing and fixing C.I. sluice valves (with cap) complete with bolts, nuts, rubber insertions etc. (the tail pieces if required will be paid separately) including carriage of material in all leads and lifts. 150 mm diameter

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings i/c carriage of material in all leads & lifts.

Providing and fixing C.P. Brass toilet paper holder i/c carriage of material in all leads & lifts.

Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms. Including carriage of materia in all leads and lifts.

Providing and fixing two hole basin mixing Faucet including carriage of materia in all leads and lifts.

Providing and fixing wall mixing faucet for shower and bath with overhead pipe (1210cm) and bath shower Including carriage of materia in all leads and lifts.

Making connection of drain or sewer line with existing manhole including breaking into and making good the walls, floors with cement concrete 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) cement plastered on both sides with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement and making necessary channels for the drain etc. complete including carriage of material in all leads and lifts. For pipes 100 to 250 mm diameter

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design including carriage of material in all leads & lifts. Inside size 90x80 cm and 45 cm deep including S.F.R.C. manhole frame and cover medium duty 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Extra for depth over item No. 129 including carriage of material in all leads and lifts. Size 90x80 cm With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality including carriage of material in all leads & lifts. Circular shape 560 mm internal diameter

Providing and laying HDPE Water pipe 20mm dia including carriage of material in all leads and lifts.

Supplying and fixing 1.00 H.P. Motor for lifting the water from RWHT to PVC Water Storage Tank including carriage of material in all leads and lifts.

suman kumar sharma