SPECIAL REPAIR TO BLDG NO P-02 (SWIMMING POOL) AT RMS DHOLPUR.

Amount

Dismantling Stone slabs in roofs, suspended floors, chajjas, landings, etc., any thickness, jointed in any mortar including cleaning of Mud in roofs, any thickness and demolition of existing PCC & plastering and leeping (whether full thickness removed or only a part there of including removing the demolished material 100 m away from site and disposal in low lying area complete all as specified and as directed by Engineer-in-Charge.

M&L Dholpur stone roof slabs, self faced 10cm to 15cm thick, 45cm to 60cm wide and 3.5m Long, hoisted and set, jointed and grouted and set in cement mortar 1:3, complete all as specified and directed.

M&L Dholpur stone roof slabs, self faced 10cm to 15cm thick, 45cm to 60cm wide and 3.5m Long, hoisted and set, jointed and grouted and set in cement mortar 1:3, Except Stone Slabs complete all as specified and directed.

M&L for sand stone slabs 10 cm thick in sun shades, chajjas, shelves, cills, landings slab, cover stones, templates, etc. n. exc. 4 m in length, punched dressed on face and along exposed edges, self faced on other side and set in lime mortar 1:2 or cement mortar 1:4 complete all as specified and directed.

M&L for 50 mm thick plain cement concrete 1:2:4, type B-1 (using 20 mm graded stone aggregate) as in floors and paving on stone slabs in roofs including finished even and fair without using extra cement complete all as specified and directed.

M&L for screed bed or bedding layer 15 mm thick in cement mortar 1:4 mixed with water proofing liquid as per manufactur’s direction, finished even and smooth without using extra cement as in roof complete all as specified and directed. Note :- Liquid water proofing compound shall be measured and paid separately.

Supply only water proofing compound ISI marked all as specified and directed.

M&L for APP based polymeric membrane not less than 3mm thick , weighing not less than 3.5 Kg / sqm and minimum 3mm thick reinforced with polymer non wove fabric(wt. not less than 150gms/Sqm) It shall be laid by torch application .Side over laps shall be 75 mm and the end shall be 100 mm and all overlaps and joints shall be sealed by torch application including applying a coat of cold applied bitumen primer conferming IS:3384 @ 0.40 Kg/Sqm and applying hot blown bitumen 85/25 spread per 1.2 Kg/sqm complete all as specified and directed.

M&L for cutting grooves in stone walls 75 mm wide and 65 mm deep and shaping horizontal face of groove with cement mortar 1:3 complete all as specified and directed.

M&L for providing PCC (1:2:4) type B0 using 12.5 mm graded stone aggregate as in roof kerbs rounded or chamfered on edges or sloping of roof complete all as specified and directed.

Taking down chowkhats or frames not exc. 1.5 sq. m each with shutters including iron mongry (without taking off shutters from the frames) complete all as specified and directed.

Taking down chowkhats or frames exc. 1.5 sq. M but not exc 4 sqm each with shutters (without taking off shutters from the frames) complete all as specified and directed.

Material and labour for Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified, including powder Coating (minimum thickness of powder coating 50 micron), complete all as specified and directed.

S&F powder coated anodised Aluminium door shutters,aluminium section weighing 0.55 kg/m including necessary joining cleats,glazing clips, ruber neoprene packing,handles 2 Nos in each door, hinges,anodised aluminum snap beading screws etc. (minimum thickness of powder coating 50 micron) complete all as specified and directed.

S&F powder coated Anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle size (1no.) complete all as specified(minimum thickness of powder coating 50 micron) complete all as specified and directed.

S&F Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, complete all as specified and directed.

S&F 140 mm long floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified & directed.

S&F door closer hydraulically regulated designation No 2, aluminium (Die cast) body, universal type suitable for door shutters of 701 to 850 mm in width and of weight between 36 to 60 Kg fixed & repair complete all as specified & directed.

S&F PVC Door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS squar tube , fixing in opening complete all as specified and directed.

S&F factory made solid panel PVC door shutters 30 mm thick (style) consisting of fram made out of MS tubes for top & bottom rails. MS fram shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the MS fram welded/sealed to the stiles & rails with suitable PVC sheet beading, and jointed together with solvent cement, suppling & fixing in the fram at site complete all as specified and directed.

Supply Only Butt hinges 100mm , extruded Aluminium alloy with galvanized mild steel hinge pin,anodised and fixed , type B-21 complete all as specified and directed.

S&F 125 mm Aluminium handles, cast type, anodised complete all as specified and directed.

S&F 150 mm Aluminium anodised,barrel tower bolts of extruded section complete all as specified and directed.

Takind down GI tubing of 15 mm dia and connection and incl cleaning for refixing or removel complete all as specified and directed.

Takind down GI tubing of 20 mm dia and connection and incl cleaning for refixing or removel complete all as specified and directed.

Cutting chases for concealed water tubing or concealed conduit & making good in CM 1:3 of girth exe 10 cm in stone, concrete block or slab wall etc complete all as specified and directed.

S&F 15 mm dia galvanized pipes medium grade with all fittings and fixed complete wall and ceiling or laid in floors complete all as specified and directed.

S&F 20 mm dia galvanized pipes medium grade with all fittings and fixed complete to wall and ceiling or laid in floors complete all as specified and directed.

S&F in repair Bib taps, cast copper alloy Chromium plated with crutch or butterfly handle, screwed for iron pipe of 15 mm bore or for brass ferrule and fixed complete all as specified and directed.

S&F in repair 15 mm bore Stop valves/angle valve, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

S&F in repair Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly nuts, screwed for iron pipe and fixed of 15 mm bore complete all as specified and directed.

S&F in repair vitreous china wash basin white, ovel type of size 580x 450mm including 32 mm dia PTMT waste coupling & Waste pipe, pair of MS angle brackets or MS fastener/ bolts for fixing arrangements complete all as specified and directed.

S&F in repairs white Vitreous china wash down water closet (pedestal pattern) with fixing bolt, Plastic water closet seat, white, closed pattern with flat bottom, and cover with aluminised hinging device, including all connection complete all as specified and directed.

S&F in Repair 10 Liters PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets complete all as specified and directed.

S&F in repair Hand Shower (health faucet) ABS chrome plated with 8mm dia 1.20 meter long flexible tube and wall hook complete all as specified and directed.

S & F in repair brass chromium plated shower rose 125 mm size swivel type with connecting rod 15 mm bore complete all as specified and directed.

S&F in Repair Tubular towel rail, 20mmdia, D type, 60cm long between flanges complete all as specified and directed.

S&F in repair stainless steel gratings of outer frame dia 100 mm openable type incl all necessary fittings such as hinges including embeding in tiles with white cement complete all as specified and directed.

S&F in repair Soap dish holder (SS), any type, fixed to plugs with chromium plated brass screws complete all as specified and directed.

S&F in repair PVC connection 15 mm size with PTMT nuts of length 450mm fixed complete all as specified and directed.

S&F rotational moulded plyethylene water storage tanks 1000 litres capacity (cylindrical vertical with closed top) hoisted and fixed in position all as specified including locking arrangement for cover using MS flat 40x3mm and necessory fittingsand incl dismantling of old tank complete all as specified and directed.

S&F 20 mm bore Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed. (Minimum weight 2 0mm-210gms) complete all as specified and directed.

S&F in repair PVC SWR pipes 110 mm bore single socketed in any length with rubber ring joint fixed to wall or laid in trenches or in floors with steel clamps complete all as specified and directed.

S&F in repair PVC SWR pipes 75 mm bore single socketed in any length with rubber ring joint fixed to wall or laid in trenches or in floors with steel clamps complete all as specified and directed.

S&F in repair PVC (SWR) floor trap plain including jointing with solvent cement 75 mm dia complete all as specified and directed.

S&F PVC (SWR) junction single, (Single T) equal or unequal of 110 mm bore provided with access door complete all as specified and directed.

S&F PVC SWR bends of 75 mm bore provided with access door complete all as specified and directed.

S&F PVC (SWR) WC connector with lip ring 110 mm complete all as specified and directed.

S&F in repair PVC (SWR) vent cowl 110 mm bore complete all as specified and directed.

Demolitiion of brick work/stone boulder masonary, built in cement mortar or cement lime mortar including all quions arches,pillars etc but excluding ashlar facings,dressed stone work and precast concrete but exceeding ashlar facingdressed stone work and precast concrete articles complete all as specified and directed.

M&L for walling of random rubble, uncoursed well bonded bedded, and solidily hearted, built in cement mortar 1:6 complete all as specified and directed.

M&L for walling of random rubble, uncoursed well bonded bedded, and solidily hearted, built in cement mortar 1:6.but except stone complete all as specified and directed.

Extra over stone walling for hammer dressing to face stones and dressing,of face beds and joints, as specified, of random rubble walling uncoursed or brought up to courses with maximum depression on face from straight edge held against the dressed surface n. exc. 40 mm, on lime or sand stones complete all as specified and directed.

M&L for plain cement concrete type B1 1:2:4 (20 mm graded aggregate) as in lintels upto 1.5 m clear sp and other similar bands, plinth courses, string courses,parapets and railings upto 60 cm in height, copings, kneelers, apex stones bed plates, water troughs and the like including weathering, slightly rounded or chamfered anglesand throating, complete all as specified and directed.

M&L raking out joints pointing to random rubble or polygonal rubble uncoursed or brought up to courses built in cement mortar complete all as specified and directed.

M&L for Raised pointing to random or polygonal rubble, uncoursed or brought upto courses in cement mortar 1:4 complete all as specified and directed.

Taking down cement plaster of any description on brick or stone walls or from concrete surface incl racking out joints hacking for key scrubbing with water etc complete all as specified and directed.

M&L rendering 15mm thick in cement mortar 1:6 finished even and smooth without using extra cement on stone masonry surfaces complete all as specified and directed.

M&L for rendering 15mm thick in cement mortar 1:4 on stone masonry surfaces or surface other than fair face of brick work of walls, finished even and sommoth without using extra cement on edges/ Chajjas/Roof projection and simlar courses etc. complete all as specified and directed.

M&L for Complete removal of existing treatment,washing, rubbing down and stopping of distemperd and painted surface of old surface by Electric Rotary grinder including brooming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorscent salts and trading oil and greasy spots of Wall Surface removing of nails, making good holes , cracks etc , cleaning of floors , glasses, joinery of drops and splashes incl all arrangement necessary for execution of work complete all as specified and directed.

M&L for including sand paper gentle rubbing to obtain smooth surfaces and applying Two coats of Plastic emulsion paint white or tinted (copolymer based resin glue to be added for longer durability and better finish) using hand roller over 1mm thick wall care putty on Wall Surface including all necessary arrangement for execution of work complete all as specified and directed.

M&L for sand paper gentle rubbing to obtain smooth surfaces and applying Two coats of oil bound distempering (copolymer based resin glue to be added for longer durability and better finish) using hand roller over 1mm thick wall care putty (Birla Whie or equivalent) on Ceiling Surface including all necessary arrangement for execution of work complete all as specified and directed.

M&L for 2 coats of cement base painting on newly plastered surfaces of wall incl preparation of surfaces complete all as specified and directed.

M&L for one coats painting with synthetic enamel paint to old steel or steel based surfaces of any description, not otherwise described over 10 CM width or girth including preparation of surface including all preparatory work complete all as specified and directed.

M&L for preparing surfaces of any description over 10 cm girth or width, not otherwise described and applying two coats of synthetic enamel paint over a coat of Red oxide on new surfaces of steel or iron complete all as specified and directed.

Chipping and cleaning the surfaces which are to receive the coating or treatment, must be free from oil, laitance, grease, wax, dirt or any other form of foreign material adhering on it before the water proofing job started. Dust free the surface, including removing of existing treatment/ Old felt/ loose plaster/ concrete etc and repair the joints or pointing with polymer mortar by adding bonding agent (SBR) with cement as complete all as specified & directed.

M&L for water proofing treatment on roofs/slabs/ Pool by applying FOSROC high performance & ultra flexible polymer modified elastomeric waterproofing membrane system for concrete and masonary surfaces two component polymer modified waterproof membrane which is supplied in ready mix kits.Brushbond UltraFlex, when fully cured, provides a seamless elastomeric waterproof membrane for use in roof areas, wet areas, bathroom, water tanks, swimming pool, raservoirs,precast joints where a tough elastomeric water tight membrane is required. system shall confirms to the requirement of: Adhesion to substrate (ASTM D4541:2002):>1.0 N/mm2 Tensile Strength N/mm2 (ASTM D412:2013)>1.50 N/mm2 Elongation at break(ASTM D412-2013):>150% water vapour transmission (ISO 7783:2018):20.81 g/m2.hr. 25 kg pack covers approximately 16m2 at about 1.0mm thickness depending on surface conditions and water usage. It is recommended that general resurfacing and areas subjected to light foot traffic should recieve a brushbond Ultraflex in two coats of 500 Um (microns) each to give a 1mm thick coatong. Additional coatings may be required for a water retaining structures like swimming pool, water storage tank covered with plaster/tiles. The whole pool so finished shall be hydrotest for a minimum period of 24 hours for curing and for final test. All above operations to be done in order complete all as specified and directed. Note: At least 15mm of protective plaster recommended prior to fixing tiles on proposed system as a protection.

M&L for 15 mm thick rendering/ screed bedding layer in CM 1:3 on floor and walls of pool complete all as specified and directed

Laying and application of Porclean Mosaic tiles of approved make in all defined colors and shade in swimminng pool's floor and wall laid on 6mm thick base of Fosroc Nitotile MPA Grey/White a high performance, polymer modified multipurpose adhesive @ approx 7 Kg/Sqm @ 6mm thickness using 6mm x 6mm square notch trowel including grouting the joints with approved grouts mixed with matching pigments etc. The tile adhesive shall satisfy the requirement Tensile Adhesion Strength in Dry condition> 1.5 M/mm2 and in wet condition> 1.0 N/mm2. Nitotile MPA should be mixed with clear potable water in the ratio .26 to .30 with slow speed drill fitted with a mixing paddle is recommended for mixing as per manufacturer or as complete all as specified & directed. Note:- Payment of Tiles and Tile Grout to be measured separately.

Supply only epoxy resin, chemically resistant tile grout which is excellent resistent to industrial chemicals, solvent free -can be used in confined areas, attractive appearance, easily cleaned with low odours formulations of and approved make from FOSROC/SIKA/NYK latecrite and recommended for mixing as per manufacturer or as compelete all as specified and directed

Material and labour swimming pool tiles,Endura coloured tiles of size 247x122x8mm thick in floor over 15mm thick screed bed in cement mortar 1:4 incl joining in neat cement slurry and pointed in coloured cement to match with shade of tiles complete all as specified and directed.

Material and labour swimming pool tiles,Endura coloured tiles of size 247x122x8mm thick in walls and similar works etc set and jointed in neat cement slurry and pointing in coloured cement over 10mm rendering on fair faces of wall 1:3 cement complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L for Vitrified parking tiles 300x300x10mm thick conforming to IS-4457 ,laid in floors and similar works etc as per manufacturers instructions jointed and pointed to match the shade of tiles over and 15mm thick screed bed in cement mortar laying floor finish complete all as specified and directed.

M&L Non skid coloured ceramic tiles area of each tiles exceeding 0.11 Sqm but not exceeding 0.18 sqm (400x400) 7 to 8 mm thick in floor/skirting set in neat cement slurry and pointed with coloured/white cement to match the surface complete all as specified and directed.

M&L Vitrified ceramic tiles 10mm thick (square/rectangular) light shade area of each tile not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

M&L Screed bed or bedding layer of mortar 15 mm thick in CM 1:4 for laying floor finishes complete all as specified and directed.

M&L Glazed ceramic tiles in vertical surface 300x200x7mm/ 350x 250x 7 mm/ 450X 300X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the surface over 10 mm thick CM 1:4 complete all as specified and directed.

Dismantling of stone slabs and tiles of any description or thickness in floor,apron etc. laid bedded and pointed in any mortar complete all as specified and directed.

M&L 20 mm thick Granite (of any type/ any colour) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.

Dismantling structural steel work including doors,gates but excluding framed truss etc. complete all as specified and directed.

Supply and fixing mild steel rolled sections such as angles etc. As in main and cross beam, hip and jack rafters,purlins where connected to common rafters and running rails and guides for sliding dorrs, fixed with angle cleats or other connected plates confirming to grad Fe 290 (Gde E-165) complete all as specified and directed.

S&F in repair Collapsible steel gates, top hung,consisting of channel pickets, pivoted flat bars, top and bottom runners, brass handles etc., as specified, erected in position and securing runners with holdfasts and brackets, complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level ) and removing unserviceable material exc 100 mtr complete all as specified and directed.

M&L for 75 mm thick plain cement concrete 1:3:6, type C-2 (using 40 mm graded stone aggregate) as in plinth protection including finished even and smooth without using extra cement complete all as specified and directed.

S&F stainless steel wire cloth .36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, complete all as specified and directed

Excavation in trenches not exc 1.5m in depth and not exc 1.5m wide for taking out/laying pipeline and cable and getting out in soft/disintegrated rock soil complete all as specified and directed.

Returning filling in including spreading, levelling watering and well ramming in layers not exc 25cm complete all as specified and directed.

Removing Excavated hard rock soil at a distance not exc 50m and deposited where directed complete all as specified and directed.

Supply and spread unwashed dry river sand for cushioning for covering the under ground cable in trenches complete all as specified and directed.

M&L Factory made unreinforced precast concrete cable covers conforming to IS:5820, class LV type 1 size 250x150x40 mm for cable protection complete all as specified and directed.

Supply laying and testing cable XLPE insulated sceened PVC bedded, galvanised steel strip or wire armoured electric power cable heavy duty with stranded aluminium conductor 11000 volts grade of size 25 Sqmm 4 core complete all as specified and directed.

Boring of holes under road, pavement, hard standing by trenchless technology using ultra sound technique and necessary machine or by using manual mechnical tools with manpower including passing HDPE 150 dia suitable for 0.4 mpa working pressure or GI pipe light grade 100mm bore dia for proection of LT Cables complete all as specified and directed. (Note : Quoted rate includes cost of protection pipe.)

M & L for earthing complete with Galvanized Steel earth plate electrode 60cm x 60cm x 6mm thick, buried directly in ground (earth pit not less than 2.25 M deep below ground level) with top edge of the plate not less than 1.5 M below normal ground level, connected to and including GI wire of 4 mm dia connected by means of GI bolts, nuts, and washers, protected by 15 mm bore GI light grade ISI marked pipe upto and including test points. Earthing plate shall be surrounded by alternate layers 15cm thick of charcoal or coke and common all around bottom and top, 20mm dia GI medium grade pipe for watering and including funnel, wire mesh, PCC chamber pit made with PCC (1:3:6) type C2 (using 20mm graded crushed store aggrgate) including necessary form work, excavation and earth work in any type of soil, returning filling in and disposal of surplus soil to a distance not exceed ing 50 M, pit cover 40 mm thick made with RCC (1:2:4) type B-1 (using 20mm graded crushed store aggrgate) including TMT reinforcement 80 mm dia @ 75 mm C/C both way, MS handle of 12 mm dia, cover rest on MS angle iron frame 40x40x6mm embeded in concrete duly painted with two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified and as shown in electrical plate No-3 of SSR Part-I complete all as specified and directed. Note:- (i) PCC chamber shall be constructed at least 1.5 metre away from the earth electrode and pipe for watering shall be provided in slanting manner. (ii) Protection pipe and earthing strip upto test point from top of the earth plate and further upto body of electrical equipment shall be including in the unit rate of this item. (iii) The earth testing arrangement should be done by the contractor as per direction of Engr-in-charge. No extra payment shall be made on this account.

Supply, fixing and testing LED flood light 70watt 230V AC outdoor type with thermal management in multiple optics and equipped with IP66 protection with impact and corrosion resistant complete with driver and lamp and having lumen output not less then 100 lm/w new generation energy saving, environmental friendly, long life, versatile pressure die cast aluminium with 10KV surge protection complete all as specified and directed.

S & F LED batten 20watt suitable for 1200mm long with G-13 lamp holder T5 and T8 , housing finished in alluminium powder coating complete with all accessaries complete all as specified and directed.

S & F LED light fitting mirror type with high output diffurser 2 feet, 7w/10w 220V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable suitable size complete all as specified and directed.

Supply and fixing GI water tubing IS-1239 marked, medium grade, in replacement including all necessary pipe fittings laid in trenches, on wall, under floor, under road on same or new route and making good the disturbed portion as existing and including taking down of old unserviciable pipe of the size 80mm dia complete all as specified and directed. Note :-excavation earth work will be measured and paid saperatly.

Supply and fixing sluice valves of size 80mm dia of cast iron body with forged brass spindle, class PN 1.6 and cast iron wheel head, both ends flanged, IS-1486 marked complete with neoprene rubber gasket joints, nuts, bolts (high tensile), and washers etc complete all as specified and directed.

S&F Gun metal gate/globe valve with iron wheel head screwd both ends for iron pipe and fixxed of bore 20mm complete all as specified and directed.

Construction of valve pit of size 90x90x90cm of double brick masonary with internal plastering from the top of surface including cover of MS sheet 3.15mm thick and angle iron 40mmx40mmx6mm with hinges and locking arrangement including painting with two coat of synthetic enamelled paint over a coat of red oxide and grouting to PCC 1:2:4 plastering in cement morter 1:3, foundation concrete 1:3:6 including necessary earthwork complete all as specified and directed.

S & F Sheet Metal Enclosure for DBs TPN 4 Way Double Door type complete all as specified and directed.

S & F Sheet Metal Enclosure for DBs SPN 8 Way Double Door complete all as specified and directed.

M&L submain wiring complete with 4 Sqmm single core multi standred PVC insulated and sheathed cable FRLS copper conductor two runs and one run of 4 Sqmm copper cable for earth continuity conductor(measured as one RM) in and including drawn through PVC conduit/sleeves with all PVC accessories fixed on wall, floor/ceiling and making good the distrubed surface by putti/cement and paint complete all as specified and directed.

Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete fittings such as switches, ceiling roses, pendents, regulators, sockets etc removing materials for taking credit and making good disturbed surfaces of wall, floor & ceiling etc. complete all as specified and directed.

M&L point wiring concealed type complete including cutting chases for conduit pipes on stone masonry wall with 1.5 Sqmm 02 x single core multistranded copper conductor of 1100 volts grade PVC pre insulated FRLS and unsheathed cable enclosed in PVC conduit pipes with all accessories such as Tee, bend, collar, elbow, square junction box etc fixed inside the wall/ceiling by means of PVC conduit pipes and suitable accessories including 1.5 Sqmm insulated but unsheathed copper earth continuity conductor to common earth and connedcted to earth dolly complete rate including cutting chases and finishing the wall after concealing the pipe with suitable plastering/putty/distembering etc all as specified and directed for the light points and fan points complete all as specified and directed

All as per Srl Item No. 109 above but with 2.5sqmm size

All as per Srl Item No.109 above but controlled by two 2way switch with cables 1.5sqmm in PVC conduit

All as per Srl Item No. 109 above but for one 3 pin or 5 pin 6 Amp socket point outlet on the same board with other switches

All as per Srl Item No. 109 above but for one 3 pin or 5 pin 6 Amp socket point outlet on the independent board complete all as specified and directed

S&F modular switch 1 way , 6 Amp, 1 module complete all as specified and directed

S&F modular switch 1 way , 16Amp, 1 module, complete all as specified and directed

S&F Celing Rose 3 pin terminal polycarbonate/Baketlite complete all as specified and directed

S&F modular socket 6Amp combination, 2/3 pin combined, 2 module complete all as specified and directed

S&F modular socket 6Amp/16Amp combination, 2/3 pin combined, 2 module complete all as specified and directed

S&F Modular switch 2 way 6A 1 module complete all as specified and directed

S&F modular white cover plate with frame of 3 module as per existing model and type complete all as specified and directed

S&F modular white cover plate with frame of 4 module as per existing model and type complete all as specified and directed

S&F modular white cover plate with frame of 6 module as per existing model and type all as specified and directed.

S&F modular flush metal box 3 module complete all as specified and directed

S&F modular flush metal box 4 module complete all as specified and directed

S&F modular flush metal box 6 module complete all as specified and directed

S&F MCB TPN 40A Curve C 415V 10kA complete all as specified and directed.

S&F MCB SPN 32A Curve C 240V 10kA complete all as specified and directed.

S&F MCB SP 6 to 32A Curve C 240V 10kA complete all as specified and directed

GOVIND CONSTRUCTION (BID ID -3145253)

Rajesh Mishra (BID ID -3152145)

PD GUPTA AND COMPANY (BID ID -3145309)

M/s S. K. Construction Co. (BID ID -3146108)

M/S MAKHIJA TRADERS (BID ID -3145298)