Additional work for Construction of 100 bedded Maternity Child Health Wing with accommodation of Staffs at existing North Lakhimpur C.H. in Lakhimpur Dist

Amount

Earthwork in excavation for foundation trenches of walls, retaining walls, footings of column, steps, septic tank etc. including refilling (return filling) the quantity as necessary after completion of work, breaking clods in return filling, dressing, watering and ramming etc. and removal of surplus earth with all lead and lifts as directed and specified in the following classification of soils including bailing out water where necessary as directed and specified. Up to depth of 2.00m below the existing ground level. In ordinary soil.

Earth/ sand filling in plinth in layers not more than 150mm thick including necessary carriage, watering, ramming etc. complete as directed and specified including payment of land compensation, forest royalty, sales tax and other duties and taxes as may be necessary. With river sand or silt (predominantly non plastic) by truck carriage including loading and unloading.

Raising low site around the building with approved soil obtained from outside by truck carriage including breaking clods, dressing etc. complete including paying necessary forest royelty, sales tax, land compensation, municipal gate fees, if any monopoly duty etc. (profile measurement to be taken and 12.5% deduction for shrinkage to be made from total quantity) etc. complete as directed and specified. Other than Guwahati city

Plain cement concrete works with coarse aggregate of sizes 13mm to 32mm in foundation bed for footing steps, walls, brick works etc. as directed and specified including dewatering if necessary, and curing complete (shuttering where necessary shall be measured and paid separately). In prop 1:3:6

Providing and laying plain/reinforced cement croncrete works cement, coarse sand & 20mm down graded stone aggregate including dewatering if necessary, and curing complete but excluding cost of form work and reinforcement for reinforced cement concrete work (form work and reinforcement will be measured and paid separately) Using Batching Plant/ RMC/ Truck mounted batching plant including Transit Mixer and Concrete Pump. M-20 grade concrete.

Providing and laying plain/reinforced cement croncrete works cement, coarse sand & 20mm down graded stone aggregate including dewatering if necessary, and curing complete but excluding cost of form work and reinforcement for reinforced cement concrete work (form work and reinforcement will be measured and paid separately) In substructure up to plinth level Foundation, footing, columns with base tie and plinth beam, pile cap, base slab, retaining walls, walls of septic tank, inspection pit and the like and other works not less than 100mm thick up to plinth level. M-20 grade concrete.

Providing and laying plain/reinforced cement croncrete works cement, coarse sand & 20mm down graded stone aggregate including dewatering if necessary, and curing complete but excluding cost of form work and reinforcement for reinforced cement concrete work (form work and reinforcement will be measured and paid separately) In substructure up to plinth level Foundation, footing, columns with base tie and plinth beam, pile cap, base slab, retaining walls, walls of septic tank, inspection pit and the like and other works not less than 100mm thick up to plinth level. M30 grade concrete

Extra for using plasticiser (Masterplast [email protected] Litperbag of cement or SPL-2 @0.15 Lit per bag of cement or equivalent) air entraining and water reducing plasticiser (Masterplast PEA @ 0.15 Lit per bag of cement or equivalent) conforming to IS-9103-1999 For M-20 Grade concrete or prop 1:1:5:3

Providing form work of ordinary timber planking so as to give a rough finish including centering, shuttering, strutting and propping etc., height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removal of the same for in-situ reinforced concrete and plain concrete work in: (I) Foundation, footings, bases of columns, pile cap, raft and mass concrete works etc. Using 25 mm thick plank.

(II) Sides and Soffits of Beams, beam haunchings, cantilever girders and bressumers.

(III) Columns, Pillars, Posts & Strut of square/ rectangular/ polygonal in plan or any shape like Tee/L etc. having plane vertical face

(iv) Flat Surfaces such as soffits of suspended floors, roofs, landings and the like.

(v) Vertical surface such as walls (any thickness), Lift shafts, partitions and the like including attached pilasters, butresses, plinth and string courses and the like.

Providing formwork using 2mm pressed bend shuttering plate of mild sheet and tubular telescopic steel props including centering, shuttering, strutting and propping etc. complete and removal of the same for in situ reinforced concrete and plain concrete work in: (I) Vertical surface such as walls (any thickness), Lift shafts, partitions and the like including attached pilasters, butresses, plinth and string courses and the like

(II) Flat Surfaces such as soffits of suspended floors, roofs, landings and the like

Providing brick soling in foundation and under floor with stone/ best quality picked jhama brick, sand packed and laid to level and in panel after preparing the subgrade as directed including all labour and materials and if necessary dewatering, complete. Brick on flat soling

Cement plaster skirting with cement mortar in prop. 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement including rounding of junctions with floor. 15 mm thick

Providing VITRIFIED floor tiles of approved quality of specified size, shape and thickness not less than 18mm on floors, skirtings, risers and treads of steps over 15 mm thick base of cement mortar in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with flush pointing with Fix-A-Tile (Choksey/Sika/Pedelite/Rouf) / white cement slurry mixed with approved pigment to match shade of tiles, mixed with approved pigment to match the shade of the tiles, complete at all levels as specified and directed. (Coloured pigment should be in conformity with colour of tiles and as approved and directed by the Department) Deluxe range (800mm x 800mm) Somany/ Nitco/ Varmora/ Asian Granite make.

Providing polished ceramic wall tiles of approved quality, size, shape and thickness not less than 8mm on walls and skirtings over cement mortar bed 10 mm thick in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with flush pointing with Fix-A-Tile (Choksey / Sika / Pedelite / Rouf) /white cement slurry mixed with approved pigment to match shade of tiles complete at all levels as specified and directed. (Cement plastering to be measured and paid separately). (Coloured pigment should be in conformity with colour of tiles and as approved and directed by the Department). (Walls means both interior and exterior walls). Wall Tiles - Deluxe range (Size 300mm x 600mm) Somany/ Nitco/ Varmora/ AGL

Providing Antiskid vitrified Tiles of approved quality size, shape not less than 8mm on floor, skirting over a cement mortar bed 15mm thick of 1:3 (1 cement: 3 coarse sand) approved make fix with Fix-A-Tile (Choksey/ Sika/ Pedelite/ Rouf)/ white cement complete at all level as specified and directed. Floor Tiles - Deluxe range (Sizes 600mm x 1200mm) Somany/ Nitco/ Varmora/ AGL

Providing polished SUNROCK-Hi CTS/ MULTIWYN tiles of approved quality, size, shape and thickness not less than 18mm on floors and skirtings over cement mortar bed 10 mm thick in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with flush pointing with Fix-A-Tile (Choksey / Sika / Pedelite / Rouf) /white cement slurry mixed with approved pigment to match shade of tiles complete at all levels as specified and directed. (Coloured pigment should be in conformity with colour of tiles and as approved and directed by the Department). SUNROCK-HI CTS/MULTIWYN

18 mm thick Marble stone slab flooring of sizes 1200x1200 including treads and risers of steps, skirting, laid over 20 mm thick base of cement plaster 1:6 (1 cement : 6 coarse sand) laid and jointed with grey cement slurry including rubbing and polishing complete with marble slab of specified quality and shade at all levels. Dungri slab

15 mm thick Cement plaster in single coat on single or half brick wall for interior plastering up to 1st floor level including arises, internal rounded angles, not exceeding 80mm girth and finished even and smooth including curing complete as directed. In prop 1:4

Supplying, fitting and fixing in position reinforcement bars conforming to relevant I.S. Code for R.C.C. work/ R.B. walling including straightening, cleaning, cutting and bending to proper shapes and length as per details, supplying and binding with 20G annealed black wire and placing in position with proper blocks, supports, chairs, spacers etc. complete (No extra measurement for lap, hook, chair, anchor etc. will be entertained in the measurement as they are included in the rate) (Upto 1st floor level) From Primary Producer: TATA/ SAIL/ Esser Steel/ Jindal steel/ Shyam steel/ RINL

Supplying fitting, fixing Armstrong mineral fibre acoustic suspended ceiling systen fine fissured (tegular) edge tiles with Armstrong XL 24mm exposed grid. The tile should have humidity resistance of 99% NRC 0.55, light refraction>85% thermal conductivity 0.052-0.057 w/mk, in module size 600mm x 600mm x 16mm. Thegrid should have 24mm wide T. section having rotary stiching on all T sectionie the main runner 1200mm x 600mm cross Tees with web height of 43.35 and 30mm (which ever is required and load capacity of 23.78kg/m2. The section galvanising of 120gm/m2 complete as directed & specified. Armgyp.- ( Broad Dew drops, Tablet, Snow Frost) edge tile with 24mm exposed grid.

Construction of Granular sub-base by providing close graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with vibratory roller to achieve the desired density, complete as per Clause 401 of MoRTH specifications (with an initial lead of 5 km) (including cost of testing of materials at site and laboratory as directed by the deptt.) Using Grading II material

Providing and laying of inter locking concrete block pavement (ICBP) with cement concrete paver blocks as per IS 15658-2006 of thickness 80mm and 28 days compressive strength not less than 30 N/m over a layer of bedding sand of compacted thickness 30mm, laid either in stretcher/ running/ herringbone pattern of bonds as directed by the engineer and in proper level and grade and compacted with appropriate equipment such as plat vibrator along with spreading of a thin layer of joint filling sand to fill up the gaps between blocks including construction of edge restraint wherever required complete as per drawings and Technical specification clause 1504 of MORD.

Wiring for light/fan/call bell point with 2 x 1.5 sq. mm. P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolyic copper conductor for voltage grade upto 1100 volts (Finolex/RR Kabel or equivalent Make as approve by the Deptt.) in surface/ recessed conduit wiring system with 20 mm dia 2mm thick / havy rigid PVC IS:9537 Part - III conduit (Berlia/ AKG / Precision/ Presto Plast/ Polycab/ MW or equivalent make as approved by the Deptt.) including 6 Amp flush type switch/ bell push (Anchor penta/Gold Medal Kolor/ kany. Kom/ Havells or equivalent make as approved by the Deptt.) GI/ MS switch board (ISI marked) with phenolic laminated sheet cover, ceiling rose (Anchor penta/ Gold Medal/ Kolor kany.kom/ Havells or equivalent make as approved by the Deptt.) etc. complete (i) Medium point up to 6.00 metre. Length.

(ii) Long point up to 10.00 metre. Length.

Wiring to 5 pin 6 Amps plug with 1.5 sq. mm PVC. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed elyctrolytic copper conductor for voltage grade upto 1100 volts (Finolex/RR Kabel or equivalent Make as approve by the Deptt.) in surface/ recessed 2 mm thick/ heavy rigid ISI marked IS: 9537 Part - III rigid PVC conduit (Berlia/ AKG / Precision/ Presto Plast/ Polycab/ MW or equivalent make as approved by the Deptt.) wiring system including 5 pin 6 Amps flush type plug socket and 6 Amps F/T switch (Anchor penta/Gold Medal Kolor/ kany. Kom/ Havells or equivalent make as approved by the Deptt.), GI/ MS switch board (ISI marked) with phenolic laminated sheet cover including earth continuity with 1.5 sq. mm. cable to third pin of the plug socket etc. as required complete,when placed everywhere. (i) Medium point up to 6.00 metre. Length.

(ii) Long point up to 10.00 metre. Length.

Wiring for 5/6 pin 16 Amps power plug point with 4 sq. mm. P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolyic copper conductor for voltage grade upto 1100 volts (Finolex/RR Kabel or equivalent Make as approve by the Deptt.) in surface/ recessed conduit wiring system including and fixing 5/6 pin 16 Amps flush type socket outlets and 16 Amps flush type switch (Anchor penta/Gold Medal Kolor/ kany. Kom/ Havells or equivalent make as approved by the Deptt.), GI/ MS switch board (ISI marked) with phenolic laminated sheet cover including earth continuity with 2.5 sq. mm. cable to 3rd pin of the plug socket as required complete with 20 mm. dia, 2mm. thick/heavy rigid ISI marked IS: 9537 PART-III rigid PVC PVC conduit (Berlia/ AKG / Precision/ Presto Plast/ Polycab/ MW or equivalent make as approved by the Deptt.) (i) Extra long point up to 20.00 metre. Length.

(ii) Extra long point up to 25.00 metre. Length.

Wiring for drawing sub-main line with P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed elyctrolytic copper conductor for voltage grade upto 1100 volts (Finolex/RR Kabel or equivalent Make as approve by the Deptt.) PVC conduit (Berlia/ AKG / Precision/ Presto Plast/ Polycab/ MW or equivalent make as approved by the Deptt.) including earth continuity in surface/recessed 20 mm. dia. 2mm thick/heavy ISI marked IS: 9537 PART - III rigid PVC conduit wiring system. (i) With 2 x 2.5 sq. mm + earth continuity with 1 x 1.5 sq. mm. in 20 mm. dia 2 mm thick/heavy rigid PVC IS:9537 Part - III conduit

(ii) With 2 x 4 sq. mm + earth continuity with 1 x 2.5 sq. mm. cable in 20 mm. dia 2 mm thick/heavy rigid PVC IS:9537 Part - III conduit

(iii) With 2 x 6 sq. mm + earth continuity with 1 x 4 sq. mm. cable in 25 mm. dia 2 mm thick/heavy rigid PVC IS:9537 Part - III conduit

(iv) With 2 x 10 sq. mm + earth continuity with 1 x 6 sq. mm. cable in 25 mm. dia 2 mm thick/heavy rigid PVC IS:9537 Part - III conduit

Wiring for drawing sub-main line with PVC insulated unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed elyctrolytic copper conductor for voltage grade upto 1100 volts (Finolex/RR Kabel or equivalent Make as approve by the Deptt.) including earth continuity in surface/recessed 20 mm. dia. 2mm thick/heavy ISI marked IS: 9537 PART - III rigid PVC conduit (Berlia/ AKG / Precision/ Presto Plast/ Polycab/ MW or equivalent make as approved by the Deptt.) wiring system. (i) With 3 x 4 sq. mm + earth continuity with 2 x 2.5 sq. mm. in 25 mm. dia 2 mm thick/heavy rigid PVC IS:9537 Part - III conduit

(ii) With 3 x 6 sq. mm + earth continuity with 2 x 4 sq. mm. in 25 mm. dia 2 mm thick/heavy rigid PVC IS:9537 Part - III conduit

With 3 x 10 sq. mm + earth continuity with 2 x 6 sq. mm. in 25 mm. dia 2 mm thick/heavy rigid PVC IS:9537 Part - III conduit

With 3 x 16 sq. mm + earth continuity with 2 x 10 sq. mm. in 32 mm. dia 2 mm thick/heavy rigid PVC IS:9537 Part - III conduit

Supplying, Fabrication, Erection, Testing commissioning of vermin and dust proof (IP-43 protection) totally enclosed cubical type compartmental floor mounting Panel board of size 1950mm 1000mm X 500mm made of 16 SWG (1.6mm thick) C.R. sheet and 300mm x 30mmx5mm MS Angle having 4 nos legs at the bottom and C.R. sheet roofing on the top complete with 2 coats of Red Oxide metal primer and painting with powder coated paint. The panel board is to be erected in 1:3:6 PCC foundation including excavation complete neatly wiring done, with tyhe provision for the following electrical accessories. Incomer 1. 250 A 4Pole 50KA AC 415V MCCB OUTGOING. 1. TPN MCB 10 nos 2. 3Phase K.W.H. meter (L&T) 3. 0-250 A (Digital) Ammeter 4. 0-500 V (Digital) Voltmeter 5. Ammeter S/S in 3 Position 6. Ammeter S/S in 3 Position 7. Indicator Lamp (R,Y,B) 8. 2A Slide Lock Fuse 9. 250/5 CT Coils 10. Control wiring along with required size of copper bus bar (incoming and Outgoing MCCB/ MCB will be paid extra)

Supply and laying of following size PVC/XLPE.insulated and PVC sheathed 1.1 KV Grade Solid Aluminium conductor up to 10 sq mm balance stranded conductor, XLPE Insulated, cores laid up, PVC tape inner sheathed, Armour ( Aluminium for single core up to 70 sq mm balance Aliminium strip, Galvanised for cables up to 2 x 10 sq mm. 3x 10 sq mm 4 x 6 sq mm balance all galvanised steel strip), extruded PVC Type ST2 sheathed, 650/1100V grade as per IS 7908 (Part 1) 1988 armoured U.G. cable U.G. cable laid in ground/partially in air (as required for termination over ground including excavation of cable trench up to depth of 75cm, refilling, protective brick covering, Sand cushioning etc complete handling of surplus spoil, debris to proper as specified and directed by the deptt. (Nicco/ Havells/ RPG/ CCI/ Polycab/ GHloster/ Finolex make) (i) 50.00 Sq. mm.3 & 1/2 Core armoured U.G. Cable

(ii) 95.00 Sq. mm.3 & 1/2 Core armoured U.G. Cable

Supply and laying of following size Solid Aluminium conductor up to 10 sq mm balance stranded conductor, XLPE Insulated, cores laid up, PVC tape inner sheathed, armour Aluminium for single core up to 70 sq mm balance Aliminium strip, Galvanised for cables up to 2 x 10 sq mm. 3x 10 sq mm 4 x 6 sq mm balance all galvanised steel strip) extruded PVC Type ST2 sheathed, 650/1100V grade as per IS 7908 (Part 1) 1988, LT armoured U.G. cable U.G. cable laid in pucca flooring, road crossing, drain crossing as per site requirement and partially in air to connection as approved by the Depts. the control switch, through medium duty GI Pipe (Tata/Nezone make or equivalent as approved by the Deptt) bend and socket including excavation and refilling the trench and making good damage done as specified and directed by the deptt. (Nicco/ Havells/ RPG/ CCI/ Polycab/ GHloster/ Finolex make) (i) 50.00 Sq.mm 3 & 1/2 Core U.G. cable in 50 mm dia medium duty hot dip galvanised pipe (AKG or equivalent as approved by the Deptt.)

(ii) 95.00 Sq.mm 3 & 1/2 Core U.G. cable in 65 mm dia medium duty hot dip galvanised pipe (AKG or equivalent as approved by the Deptt.)

Supplying including installation, connection as approved by the Deptt., testing and commissioning of CENTRIFUGAL MONOBLOCK PUMP SET complete as directed and specified by the deptt. 2 HP single Phase Centrifugal monoblock pump set (Crompton Greaves/ Aquatic / CRI/ V-Guard make) 2900 rpm with DOL Starter (Crompton Greaves/ Control & Switch Gear/ BCH/ L&T/ Siemens make)

Supplying, installation & testing of Copper Plate earth station with 600 mm x 600 mm x 3 mm copper earth plate with necessary 40 mm dia. G.I. medium duty watering pipe with G.I. Fittings such as socket, Tee, elbow, nipple, and 50 mmx 40 mm G.I. reducing socket for funnel including locking arrangement with 300 mmx300 mmx6 mm C.I. hinged cover plate complete with digging of earth pit, construction of brick chamber and plastering pof both inner & outer surface as specified and directed by the deptt

Supplying, installation & testing of Copper Plate earth station with 600 mm x 600 mm x 6 mm copper earth plate with necessary 40 mm dia. G.I. medium duty watering pipe with G.I. Fittings such as socket, Tee, elbow, nipple, and 50 mmx 40 mm G.I. reducing socket for funnel including locking arrangement with 300 mmx300 mmx6 mm C.I. hinged cover plate complete with digging of earth pit, construction of brick chamber and plastering pof both inner & outer surface as specified and directed by the deptt

Extra for using salt 5kg and charcoal 96 kg in GI/Copper plate Earth Station pit to provide low impedance ground in location of high soil resistivity as and when required and specified by the deptt.

Supplying and laying 8 SWG G.I. earth drawn through 15 mm dia. Medium quality G.I. pipe from Earth Electrode (below G.L.) to electrical switch gears or electrical machineries including making necessary connection as approved, specified and directed by the deptt.

Supplying including fitting and fixing of followingstar rated A.C. Ceiling fan complete with all accessories like down rod, canopy etc. of following sweeps with making necessary connection cable as approved by the Deptt.etc. as required complete and as directed by the Department [ without regulator]. (ORIENT PSPO make / Usha make/ CROMPTON make/ Havells/ ATC/ V GUARD make) Energy efficient 5-star 1200 mm sweep. ORIENT PSPO make / Usha make/ CROMPTON make/ Havells/ ATC or equivalent make

SRI TARUN DUTTA