ELECTRIFICATION FOR PRIMARY HEALTH CENTRE

Amount

ELECTRIFICATION

Wiring for light point/fan point/exhaust fan point /call bell point with 1.5 sqmm FRLS PVC insultated copper conductor single core cable in surface /recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 Sqmm FRLS PVC insulated copper conductor signle core cable etc. as required

Gropu C

Wiring for lignt/power plug with 2x4 sqmm FRLS PVC insulated copper conductor signle core cable in surface/Recessed medium class PVC conduit along with 1 No. 4 Sq.mm FRLS PVC insulated copper conductor signle core

Wiring for circuit/submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor,, single core cable in surface /Recessed medium class PVC conduit as

2X2.5 Sq.mm +1X2.5 Sq.mm Earth Wire

4x16 Sq.mm +2x6.0 Sq.mm Earth Wire

2X10 Sq.mm +2X6.0 Sq.mm Earth Wire

Suppling and fixing following modular switch/socket on the existing modular plate and switch box including connections but excluding modular plate etc. as required

Bell Push

Supply and fixing call Bell/Buzzer suitable for single phase 230V complete as required

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providng and fixing 2 nos. 3 pin 5/6 A modular socket outlet and 2 nos. 5/6 A modular switch, connections etc. as required. (For light plugs to be used in non residential buildings).

Suppling and fixing modular banking plate on the existing modular plate and switch box excluding modular plate as

Suppling and fixing suitable size G.I with modular plate and cover in front on surfaceor in recess including providing and fixing 6 pin 15/16 amps modular socket and outlet and 15/16 amps modular switch connection painting etc. as required

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

Supplying & fixing suitable size GI box wih modular plate and cover in front on surface or in recess including providing and fixing 25 A modular socket outlet and 25 A modular SP MCB, "C" curve including connections, painting etc. as required.

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

12 way (4 + 36), Double door

Suppling and fixing Four pole 415 V 10Ka MCB in the existing MCBN DB complete with conections,testing and commissioning etc.as required

63A.F.P MCB 10Ka"C" curve

40A.F.P MCB 10Ka"C" curve

Supply and fixing single pole blanking plate in the exisitng MCB DB complete as required

Supplying and Fixing of Following Ratings of D.P MCB 240 Volts "C" Series in the Existing MCB D.B complete with connections,Testing and Commissioning Etc. as Required.

10 A D.P MCB 10 Ka "C" Curve

25A D.P MCB 10 Ka "C" Curve

40 A D.P MCB 10 Ka "C" Curve

63 A D.P MCB 10 Ka "C" Curve

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess,complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

12way double door

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

S P MCB

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)

Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode including connection with G.I. Nut bolt, spring, washer excavation and re-filling etc. as required.

Supply installation testing and commissioning of IP:20 Aluminium Batten 20W-22 W +- 1 W LED Surface Mounted 4 ft. with system lumen efficacy of 100 lm/W and P.F >0.9 THD <20% CCT 6500K,CRI 80 .The LED should have life of 50000 Burning Hours at L70.The input voltage shall be 150 V to 270 V.The fixture should have inbuit surge protection of 2KV.Certification-LM 79 and LM 80.The test report should be from Govt. Approved Lab/inhouse NABL Lab.

Supply installation testing and commissioning of IP20 led downlighter 15 W-18 W +/- 1 W LED Surface downlighter round shape with minimum system lumen efficacy of 100 lm/W with Pressure Die cast Aluminium Heat Sink and P.F.>0.95 ,THD<10% ,CCT 5700K, CRI 80.The LED with Useful life of 50000 Hrs at L70.. The Input voltage range shall be 150V to 270V .The Fixture should have In-built Surge Protection of 2kV. Certification:- LM79 & LM80 test report should be from govt approved Inhouse NABL lab/ government of India authorised lab .

Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CM/M/W) minimum 6.00, Air delivery minimum 210 Cum/Min , 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required.

Supply,Installation,Testing and Commissioning 320 Cu.m/Hr. AC 220-240 Volts, 50 Hz exhaust fan made out of ABS Plastic Material with inbuilt thermo cutoff Protection and Noise Level not exceeding 37 dB of Following Sizes including connection etc. complete as required .

Supplying,Installation,Testing and Commissioning of Cubical Type Indoor LT Panel Board Suitable for 415 V 3 Phase 4 Wire 50 HZ AC Supply System including Incomers,Out Goings,Bus Bars etc. as required as per the Following Description.(IP:55)(Main L.T Panel) .The successful tenderer shall take prior approval for the panel builder/fabricator alongwith G.A. drawing, wiring diagrams, single line diagram before start of fabrication of LT panel.Circuit breaker shall be capable of carrying the full load current defined for 50 degree Celsius without any derating.The Panel Builder Shall be CPRI /ERDA/ANY NABL ACCREDITED LAB approved.Refer SLD

INCOMER

MCCB 100A F.P 25 Ka Adj. Thermal & Adj. magnetic release with Extendable ROH Icu=Ics=100%

MCB 25 A D.P 10 Ka "C" Curve

OUT GOININGS

Manual Changeover 25 A D.P MCB Typ

MCB 63 A F.P 10 Ka "C" Curve

MCB 40 A F.P 10 Ka "C" Curve

MCB 10 A F.P 10 Ka "C" Curve

(Size of wiring for CTS:- 2.5 sqmm Size of wiring for voltage sensing Metering :-4.0 Sq.mm Size of wiring of all push buttons, indicating lamps:-1.5 Sq.mm Types of wires:-PVC insulated 1100V grade ,Multistrand copper conductor Flexible FR-LSH Hinged Door Earthing:-Device mounted hinged doors connected to cubicles body by means of 2.5 sqmm.green copper flexible wire . The Complete Panel Shall be Made out of 2.0 mm CRCA sheet including Frame/Partitions/Doors etc. Gland Plates to be 3.0 mm Thick.

Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc. in the existing trench, complete as required.

90 mm dia (OD-90 mm & ID-76 mm nominal)

Supplying and Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in groundin Existing DWC Pipe including excavation, sand cushioning, protective covering and refilling the trench etc as required.

3.5 C X 95 Sq.mm A2XFY

Supply and Making end Termination with Brass Compression Gland and Aluminium Lugs for the Following Sizes of PVC insulated and PVC Sheathed/XLPE Aluminium

3½ X 95 sq. mm (45mm)

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required.

1 or 2 Module (75mmX75mm)

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.

Telephone socket outlet

TV antenna socket outlet

Supplying and Fixing of Following sizes of PVC Conduit along with Accessories in surface/Recess including painting in case of surface conduit,cutting the wall and making good the same in case of recessed conduit as required.

20 mm PVC Conduit

Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required.

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required.

Supply, installation, testing and commissioning of Junction Boxes/DB-10 Pairs with Original Krone module and Back Mount Frame and have Lock -n- key, complete in all respect as per specification and desired by EIC

M/S HI-TECH SOLUTIONS

Z H CONSTRACTIONS

Bhat Electricals

universal marketing co

Firdous Ahmad Malik

M/S NASEER AHMAD PEERZADA

M/s PAMPOSH ELECTRICALS