CERTAIN REPAIR TO MAP ACCN IN THE AREA OF AGE BR-II UNDER GARRISON ENGINEER AMRITSAR CANTT .

Amount

Taking down cement plaster on brick or stone or concrete surfaces of wall etc ,icluding raking out joints , hacking for key, scrubbing down with water etc. ; Complete all as specified and directed by the Engineer-in-charge.

Material and Labour for 15mm thick cement plastering in cm 1:6 on brick or concrete surfaces other than fair surface, finished the surfaces even and fair without using extra cement ; Complete all as specified and directed by the Engineer-in-charge.

Material and Labour for 15mm thick cement plastering in cm 1:4 on brick or concrete surfaces other than fair surface, finished the surfaces even and fair without using extra cement ; Complete all as specified and directed by the Engineer-in-charge.

Material and Labour for 10mm thick cement plastering in CM 1:3 on ceiling surfaces other than fair surface, finished the surfaces even and fair without using extra cement ; Complete all as specified and directed by the Engineer-in-charge.

Material and Labour for preparation of new plastering surfaces of walls and applying two coat of cement base paint over a coat of primer etc. ; Complete all as specified and directed by the Engineer-in-charge.

Material and Labour for two coat of oil bound distemper over a coat of primer on newly plastered surface of wall incl preparation of surface ; Complete all as specified and directed by the Engineer-in-charge.

Material and Labour for Three coats of white washing on new plastered surfaces of ceiling , chajjas after preparation of surfaces ; Complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing in repairs PVC Jet spray suitable for EWC. ; Complete all as specified and directed by the Engineer-in-charge.

Supply and fixing in repairs Chromium plated Health faucet with 1.5 metre long chain ; Complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing in repairs Brass chromium plated Wall mixer with bend pipe in repairs suitable for mixing Hot & Cold water and making leakagefree connection with wall tiles & GI pipes ; Complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing Vitrous china white (Box type) toilet paper holder fixed to walls with chromium plated (CP) brass screws ; Complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing in repairs 15mm bore Concealed type stop cock cast copper alloy CP screwed down high pressure with crutch or butterfly handle ; Complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing in repairs15mm bore type angle cock cast copper alloy CP screwed down high pressure with crutch or butterfly handle ; Complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing in repairs of brass cromium brass plated fancy type bib taps 15 mm bore long nose screwed down screwed for iron pipe or for brass ; Complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing in repairs Pillar mixer with bend pipe suitable for mixing Hot & Cold water 15mm bore, cast copper alloy , with capstan heads, chromium plated , screwed down high pressure , with or without l'ettered ' 'HOT' or 'COLD' with long screwed shanks and fly-nuts , screwed for iron pipe and fixed ; Complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing Sheet glass corner shelf assembly consisting of 5.5mm thick sheet glass corner shelf with chromium plated bracket guard and railing ; Complete all as specified and directed by the Engineer-in-charge.

supplying and fixing stainless steel rolling drawer pull type suitable for kitchen cabinets with all fixing arrangement area of each drawer n exc 0.30 sqm of vertical face having depth 450mm to 600mm, ; Complete all as specified and directed by the Engineer-in-charge. Note :- Net area of front finished surface will be measured.

Supply and Fixing 15mm bib tap standard of PTMT any colour fancy type long body high pressure screwed for iron pipe and fixed (minimum weight 15 mm- 105 gms) etc ; Complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing 15mm angle stop valve of PTMT any colour high pressure screwed for iron pipe and fixed (minimum weight 15 mm- 90 gms/20 mm-92 gms) ; Complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing 15mm angle stop valve with long shank & cup (concealed type) minimun weigth 15mm-110gms/20mm-112 gms) of PTMT any colour high pressure screwed for iron pipe and fixed ; Complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing 100mm swivel type shower rose of PTMT with shower arm15 mm size, 195 mm long of any colour for fixing with 15 mm pipe ( min weight 40 gms ) ; Complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing 15mm Pillar taps,of PTMT any colour fancy type high pressure scewed for iron pipe and fixed ; Complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing in repairs for Vitreous China wash basin, white, flat back, size 500 X 400mm, excluding taps, waste, chain and plug and porcelain stopper but including brackets including cutting for and pinning in ends of brackets or erecting stand complete as in repairs ; Complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing in repairs for 10 Ltrs capacity, PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets complete with all internal accessories and fixed to wall and jam nuts on both sides, PVC flush pipe 32mm dia 90cm long fixed properly to inlet of WC and making good to disturbed surfaces of wall or floor ; Complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing of Vitreous china wash down water closet pan( pedestal pattern), white with PVC(SWR) 'P' trap 110/110mm bore ; Complete all as specified and directed by the Engineer-in-charge. Note:-Rate of supply for Flushing cistern, flush pipe, seat cover etc have been taken separately.

Supply and Fixing in repairs sinks with drainage board made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm ; Complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing in repairs PVC waste pipe 32/38/40 mm dia, 600 to 750 mm long ; Complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing in repairs PVC connections 15mm size with PTMT nuts of length 450mm ; Complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing for 40mm waste fittings, brass, chromium plated for glazed ware sinks, basins etc with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed ; Complete all as specified and directed by the Engineer-in-charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable rubbish off the premises ; Complete all as specified and directed by the Engineer-in-charge.

Material and Labour for roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc and brushing neat cement slurry with cement @ 3.0 Kg/Sqm ; Complete all as specified and directed by the Engineer-in-charge.

Material and Labour for joint free Non skid coloured ceramic tiles 7 to 8 mm thick joint free (square/rectangular) area of each tile exceeding 0.18 sqm to 0.38 sqm in floors etc set and jointed in neat cement slurry and pointed in white cement or clolured cement to match including 15 mm thick screed bed in cm 1:6 ; Complete all as specified and directed by the Engineer-in-charge.

Material and Labour for above item no. 33 but in vertical surface such as skirting, dados and risers to steps etc but including 10mm thick rendering in cement mortar 1:4 including taking down cement plaster/skirting ; Complete all as specified and directed by the Engineer-in-charge.

Material and Labour for Non-skid Ceramic colour tiles 7 to 8mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match ; Complete all as specified and directed by the Engineer-in-charge.

Material and Labour for glazed ceramic coloured tiles in vertical surface of size 350x250x7mm/ 450x350x7mmmm thick joint free on and incl 10mm thick screed bed in cm(1:4)set and jointed in neat cement slurry and pointed in colored cement mixed with pigment to match the colour of tiles ; Complete all as specified and directed by the Engineer-in-charge.

Material and Labour 20mm thick Granite (of any tpe) work (table rubbed and polished) in steps, jambs, pillars, window cills,cooking platforms and like in CM(1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over 15 mm thick Screed in CM (1:6) ; Complete all as specified and directed by the Engineer-in-charge.

Taking up or down steel tubing and connections for 15mm bore of pipe ; Complete all as specified and directed by the Engineer-in-charge.

Re-fixing for 15 mm bore old steel tubing and connections in new or old position (Walls, ceiling, floors etc) including cleaning, re-running the old screw threads etc ; Complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing for 15mm dia Tubes, 'medium grade' galvanised, with all fittings and fixed complete to walls and ceilings or laid in floors , wall etc ( surface or concealed type) ; Complete all as specified and directed by the Engineer-in-charge.

Taking up or down steel tubing and connections for 20mm bore of pipe ; Complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing for 20 mm dia Tubes, 'medium grade' galvanised, with all fittings and fixed complete to walls and ceilings or laid in floors , wall etc ( surface or concealed type) ; Complete all as specified and directed by the Engineer-in-charge.

Re-fixing for 20mm bore old steel tubing and connections in new or old position (Walls, ceiling, floors etc) including cleaning, re-running the old screw threads etc ; Complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing for 500 Ltr capacity Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position with manhole cover of tank with its locking arrangement, making hole for inlet, outlet and overflow connection including dismantling / taking down old PVC water tank, ball valve etc complete all as specified in SSR Part-I ; Complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing in repairs 20 mm Ball valves high pressure of PTMT with epoxy coat ed Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 2 0mm-210gms) ; Complete all as specified and directed by the Engineer-in-charge.

Taking down chowkats or frames with shutter’s (without taking off shutter’s from frame) nxc 1.50 sqm each ; Complete all as specified and directed by the Engineer-in-charge.

Taking down chowkats or frames with shutter’s (without taking off shutter’s from frame) exc 1.50 Sqm & nxc 4.00 Sqm each ; Complete all as specified and directed by the Engineer-in-charge. (as in doors)

Taking down shutters of any description exc 1 Sqm but nexc 2 Sqm each ; Complete all as specified and directed by the Engineer-in-charge.

Taking down and refixing same opening shutter exc.1 sqm and not exc 2 sqm each ; Complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, Doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete FE -290 Gde E-165 ; Complete all as specified and directed by the Engineer-in-charge.

Supply and fixing factory made PVC Internal door frame of size 100 mm x 45 mm with a wall thickness of 5 mm (+0.25) , made out of extruded 5 mm (+0.25) thick PVC sheet manufactured by asn ISO - 9001-2008 certified company, and by joining 3 Nos heat bent PVC sheet sections. The inside section of size 90 x 30mm shall be made from plain colour PVC sheet of 5 mm (+0.25) thickness. The inside section will be covered by sticking two sections of size 30 x 35 mm and 70 x 45 mm made from 5 mm (+0.25) thick plain PVC sheet. The frame shall be mitre cut at two corners and oined with 4 Nos of 150 mm long brackets of 15 mm x 15 mm square tube . The two vertical door frames are to be reinforced with 40mm x 20mm MS tube of 19 guage through out the frame . The door frame whslla be fixed to the wall using 8/100 mm long MS Screws through thee frame by using anchor fasteners. A minimum of 4 Nos of screws to be provided for each vertical member & minimum 2 Nos for horizontal member etc as per manufacturer's specification, ; Complete all as specified and directed by the Engineer-in-charge.

Material and Labour for Providing 30mm thick " FACTORY MADE DOOR SHUTTER - WOOD FREE consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 20mm x 40mm for stiles as well as top, bottoMaterial and Labourock rail. M.S frame shall have a coat of metal primer of approved make & manufacturer. The inside panel shall consist of 20mm thick multichamber hollow PVC section of 1 mm wall thickness, bonded using solvent cement / eynoacrylate adhesive with 5mm (+0.25) thick moulded PVC sheet of Density 600 Kg/Cbm Manufactured by an ISO-9001-2015 certified company with 2, 4, 6 raised panel design in plain/prelam colours after routing the moulded design on one side of the inside panel, 5mm (+0.25) plain/prelam PVC sheet to be pasted using solvent cement / cynoacrylate adensive on other side of the Hollow PVC section. All the four edge of the panel to be sealed with lipping of 10mm thick & 20mm wide PVC sheet baton (Made by sticking 02 Nos. foam PVC sheets of 5mm (+0.25) thickness using PVC solvent cement adhesive. Door edge lipping to be painted with PVC ink of matching colour of plain / prelam mouded PVC sheet of door. 20mm thick (5mm x 4 Nos) thick PVC sheet to be given for lock provision at lock height. Door to be fixed with frame with 3 nos. stainless steel but hinges of size 100mm *25mm*2mm and 50mm longsteel screws drilled suitable to pass through both the walls of M.S tube. other hardwares should be fixed with 25mm*8mm size steel screws etc, complete as per direction of Engineer-in-Charge, manufacturer's specification and drawing.

Material and Labour 30 mm thick Glazed and skeleton shutter open rebated and prepare to receive glass, gauge etc (without sash bars) edges of framing plain chamfered or rounded fitted with cut and mitred beads for securing gauge etc size of members of shutters as specified in SSR part-I Section 8 and clause 8.24(a) of second class hard wood ; Complete all as specified and directed by the Engineer-in-charge.

Material and Labour for Box type steel window made of ERW tube P- section of size 60 mm x 25 mm double rebated outer frame, comprises glazed skelton & gauzed shutter of ERW tube P-Section size 50mm x 20mm with one/two Nos openable leaf for each shutter consisting of two Nos Sashbar of T-section 20 x 3 mm welded to frame with one No verticle mullion of ERW box type T Section of size 60mm x 25mm and FI 2mm thick welded/screwed to frame for fixing of glass including fittings and fixture like as Handle, Tower Bolt, Stopper, Cleat, Pintal hinges, holdfast etc as given below all as shown on drg No CEJZ/TD-1020/08 Sh 1/3 to 3/3 dt 01 May 2008 complete ; Complete all as specified and directed by the Engineer-in-charge.(a) Hold fast 150mm long of 12mm x 3mm MS flat - 4 Nos per Window.(b) Handle of Z section 20mm x 25mm, 100mm long- 01 No per leaf.(c) MS tower bolt 150mm long - 02 Nos/leaf.(d) Z Section stopper 20mm x 25mm, 100mm long - 01 No per leaf.(e) Cleat 55mm long of hollow square 15mmx12mm - 02 Nos per leaf.(f) MS pintol hinges size 75mmx12mm - 2 Nos per leaf Note :- MS guard bars, sheet glass wire mesh and painting shall be measured and paid sperately ; Complete all as specified and directed by the Engineer-in-charge.

Material and Labour for Box type steel ventilator made of ERW tube P-section of size 60mmx25mm outer frame ( single rebated), comprises glazed shutter, frame of ERW tube and FI 2mm thick welded/screwed to frame for fixing of sheet glass including fixture and fittings like as Stopper, Cleat, Pintal hinges, holdfast etc all as shown on drg No CEJZ/TD1019/08 sheet 1/3 to 3/3 dt 01 May 2008 ; Complete all as specified and directed by the Engineer-in-charge. NOTE : , Guard bar, Sheet glass and painting shall be measured and paid Separately.

Supply and Fixing 35 mm thick flush shutter, soild core construction, with block board core and plywood face panel commercial type on both sides ; Complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing for 35mm thick 2nd class hard wood panelled shutters (two panels) Factory Made with lock rail & panel of 9mm BWP commercial ply or 12mm thick vineered particle board with commercial vineering on both faces, the size of rail & styles as per IS: 1003 (Part-I) klin seasoned & chemically pressure treated (factory made shutters). ; Complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing framed work such as grill, framed guard bar and similer work conforming to FE 290, GDE E- 165 ; Complete all as specified and directed by the Engineer-in-charge.

Supplying and fixing stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or stainless steel wire staples ; Complete all as specified and directed by the Engineer-in-charge.

Supplying and fixing in repairs stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or stainless steel wire staples ; Complete all as specified and directed by the Engineer-in-charge.

Hacking out old broken glass any thickness, size, quality or description from wooden frames or metal frame or stone, concrete or brick surrounds, glazed with putty or fixed with beads ; Complete all as specified and directed by the Engineer-in-charge.

Supplying and fixing 3mm thick ordinary sheet glass and glazing with oil putty or fixed with wooden beading, in squares not exc 0.50 Sqm in each panes ; Complete all as specified and directed by the Engineer-in-charge.

Supply and fixing 3mm thich figured glass pin head type and glazing with oil putty in squares not exc 0.50sqm in each pane ; Complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing 150 mm aluminum , anodised, barrel tower bolts of extruded section ; Complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing butt hinges 100mm size medium weight cold rolled mild steel, fixed with screws or welded to steel frame ; Complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing 150 mm aluminum Handle Cast type ; Complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing 250mm aluminum alloy, anodised , sliding door bolt with hasp and staple ( bolt type ) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminum alloy and fixed ; Complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing M.S. 300mm ordinary rat tail rod pattern spring including roller and roller plate complete including necessary welding to door frame ; Complete all as specified and directed by the Engineer-in-charge.

Material and Labour for preparation of new steel surface and applying two coat of synthetic enamel paint over one coat of red oxide primer on new surface ; Complete all as specified and directed by the Engineer-in-charge.

Material and Labour for preparation of new wood surface over 10 cm girth or width and apply two coat synthetic enamel paint over a coat of pink primer ; Complete all as specified and directed by the Engineer-in-charge.

Material and labour for cup board shutter, frame made of angle iron 35x35x6mm, covered with 1.00mm thick MS sheet, welded to frame including suitable handle, lugs and locking arrangement ; Complete all as specified and directed by the Engineer-in-charge.

Supply and fixing PVC sheet 5mm thick, in backside of kitchen cabinets for support ; Complete all as specified and directed by the Engineer-in-charge.

Supply and fixing PVC board 18mm thick, in cupboard shelves and backside (for hanging) kitchen cabinet etc ; Complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing solid PVC shutter 18mm thick with one side prelam of any shade plain colour as in cup board, kitchen cabinet shutter etc. ; Complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing 40 mm Continuous (piano) hinges, mild steel, bright finish or electrogalvanised ; Complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing 75-80mm long stainless steel handle ; Complete all as specified and directed by the Engineer-in-charge.

Material and Labour for providing PCC 1:2:4 type B-1 ( using 20 mm graded stone aggregate ) for fixing of hold fast ; Complete all as specified and directed by the Engineer-in-charge.

Supply and fixing, in repairs 25mm dia MS pipe PVC sheathed, decorative fancy type, curtain rod including brackets & a set of ABS finials ; Complete all as specified and directed by the Engineer-in-charge.

Taking down eaves gutters and rain water pipes ( any size or pattern) , including all fittings , heads, shoes, bends, swan necks, etc., including cleaning or refixing or removal to store ( measured overall as fixed along the centre line over fittings and accessories ; Complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing in repairs110 mm bore PVC (SWR ) pipes single socketed, in any lenth with rubber ring fixed to wall.with clamp etc ; Complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing PVC (SWR) bend 110 mm size ; Complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing 110 mm bore PVC (SWR) single Tee ; Complete all as specified and directed by the Engineer-in-charge.

Material and Labour 75 mm PVC (SWR) floor trap, plain with grating including jointing with solvent cement ; Complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing in repairs Brass chromium plated Tubular towel rail 20mm dia, D type, 60cm long between flanges ; Complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing 140 mm Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor ; Complete all as specified and directed by the Engineer-in-charge.

Material and Labour for preparation of old painted steel surfaces of any description, over 10cm in width or girth, not otherwise described for One coat of synthetic enamel paint ; Complete all as specified and directed by the Engineer-in-charge.

Material and Labour for One coat of synthetic enamel paint after preparation of old painted wooden surfaces of any description, not otherwise described, over 10cm width or girth ; Complete all as specified and directed by the Engineer-in-charge.

BISHAN DASS

Bharat Builder

Sai Construction Co.

CHARAN SINGH CONTRACTOR

GEE EMM ASSOCIATES