Provn of marksmanship training shed and boundary around the marksmanship Trg area of Garh Rif, provn of sewage line from Qtr Gd to pump house of Grenadiers and Addn/Altn of toilets of Adm Block of Grenadiers under GE (East) Ferozepur Cantt

Amount

Excavating in post holes (or similar holes) each n exc 0.5 cu m, getting out, returning, filling in and ramming in layers not exceeding 25 cm, watering and removing surplus soil to a distance n exc 50 m and making good surfaces in Soft/loose soil complete all as specified and directed.

Surface excavation in any type of soil not exceedong 30 cm deep and averaging 15 cm deep and getting out complete all as specified and directed.

M&L Cement Concrete(1:2:4),type B-1 using 20mm graded stone aggregate as in pole base concreting etc including necessary formwork complete all as specified and directed.

S&F Pre-painted galvatume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick (TCT) of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall,fixed with self tapping screws complete all as specified and directed.

S&F Pre-painted galvatume aluminium zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall,fixed with self tapping screws complete all as specified and directed.

Preparation of new steel surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over primed steel surfaces complete all as specified and directed.

S & F Roof trusses (framed), trussed, purlins, crane gantries, rails and fastening and heavy braket framing (beam, tee, angle, channel or flat sections) including distance piece, cleat of Fe-290 (Gde E-165) complete all as specified and directed.

S & F Plates (Plain or chequered) channels, Fe 290-W (E-165) square cut or notched (ordinary and counter sunk) forming holes, without any attachment complete all as specified and directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in any type of soil all as specified and directed by Engr in charge.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in any type of soil all as specified and directed.

Removing excavated material exc 250m but n exc. 500m and depositing where directed at a level n exc. 1.5 m above the starting point in any type of soil all as specified and directed.

M&L for cement concrete 1:2:4 type B1 using 20mm graded aggregate as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, coaping, plinth courses, benching, water troughs and the like including weathering, slightly rounded or chamfered angles and throating and necessary formwork complete all as specified and directed

M&L for cement concrete 1:2:4 type B1 using 20mm graded aggregate as in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces and necessary formwork complete all as specified and directed

M&L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed

M&L brick work with sub class 'B' bricks, straight or curved on plan exceeding 6m mean radius built in CM (1:6) complete all as specified and directed

M&L for rendering 15 mm thick in cement mortar (1:4) on any face of brick walls or concrete surfaces, finished fair and even complete all as specified and directed

M&L for cement concrete 1:3:6 type C-2 in concrete bed to 150mm dia drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested; in complete all as specified and directed.

M&L for 150mm dia bore of reinforced concrete pipes, class NP3, laid and jointed complete with collars complete all as specified and directed.

M&L for cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as required complete all as specified and directed.

Demolition of unreinforcement cement concrete of any description and in and position not otherwise specially provided for or as in Sunken & roof kerbs complete all as specified and directed.

M&L Cement concrete (1:5:10) type E-2 using 40mm graded stone aggregate in foundations, filling and mass concrete, as in filling under sunken floor portion complete all as specified and directed.

M&L for Rendering/plastering, 10 mm thick in cement mortar (1:3) on concrete surfaces of sunken floor and applying bitumen blown any grade applied two coats to concrete surface / rendering at the rate of 1.5 kg per sqm per coat and treating the sunken floor complete all as specified and directed

M&L APP modified polymeric membrane with mineral finish on top min 3 mm thick & weighing n. less than 3.5kgs/sqm with mineral reinforced with polyster non-woven fabric(wt n.less than 150gm/m2) laid over cold bituminous primer by torch application method with min overlap of 75mm on longitudinal direction & 100m in the transverse direction complete all as specified and directed

M&L for 40 mm thick PCC (1:2:4) type B-1 using 20 mm graded crushed stone agg.as in sub base in floors complete all as specified and directed.

M&L for Brick work in cement mortar 1:6 using sub class ‘B’ old size bricks, straight or curved on plan exceeding 6 metre mean radius including demolition of brick work built in cement mortar of any specification and in any position complete all as specified and directed.

M&L for PCC 1:3:6 type C2 using 40mm graded aggregate in foundations, filling and mass concrete complete all as specified and directed

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) removing seviceable tiles to store and rubbish off the premises complete all as specified and directed

M & L for non skid coloured ceramic tiles of 7 to 8 mm thick , area of each tile exceeding 0.11 sq m but not exceeding 0.18Sq m in floors set and jointed in neat cement slurry and pointed in white cement mixed with colour pigment to match over a screed bed of 15 mm thick in CM 1:6 complete all as specified and as directed.

S/F of Glazed coloured and cereamic tiles in vertical surfaces 300x450x7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over backing coat 10mm thick in cement mortar 1:4 for laying skirting dados and vertical surfaces all as specified and directed

Taking down cement plaster on brick walls of any description including racking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed

M&L for rendering 15 mm thick in cement mortar (1:6) on any face of brick walls or concrete surfaces, finished even & smooth without using extra cement complete all as specified and directed

M&L preparation of new plastered or unplastered surfaces and applying two coats of cement based paint over a coat of chalk white primer on walls. complete all as specified and directed

Preparation of new surfaces of wall and applying two coats of white lime wash (white washing) on walls including corneces, pillars complete all as specified and directed.

Taking down wooden chowkhats or frames with shutters (without taking off shutters from the frames) of size not exceeding 1.50 Sqm each including cutting holes in brick walls of appropriate size for insertion of cement concrete blocks for hold fasts complete all as specified and directed.

Solid PVC door frame of size 50 mm x 47 mm made of 5 mm plain colour PVC sheet reinforced with mild steel square tube complete all as specified in clause 8B.3.1 and shown on page 150 of MES Schedule Part-II (2010).

Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement, supply and fixing in the frame at site as per clause 8 B.2.1 of MES schedule Part-II (2004) complete all as specified.

S&F 100mm long aluminium, anodised barrel tower bolts of extruded section, all as specified and as directed by the Engr-in-charge.

PTMT butt hinge, 100mm long, fixed with steel screws with brass/bronze hinge pin complete all as specified and directed.

S&F 100mm Extruded aluminium alloy handle all as specified and as directed by the Engr-in-charge.

Taking up or down existing steel water tubing, 15mm bore alongwith connections fixed/laid in any situation,complete all as specified and directed

Taking up or down existing steel water tubing, 20mm bore alongwith connections fixed/laid in any situation, complete all as specified and directed

S&F Galvanised iron steel water tubing, 15mm bore, medium grade with all fittings and fixed to walls and ceilings or laid in floors complete all as specified and directed

S&F Galvanised iron steel water tubing, 20mm bore, medium grade with all fittings and fixed to walls and ceilings or laid in floorscomplete all as specified and directed

Fixing only, after cleaning old steel water tubing, 15mm bore and connections in new or old position using new fittings complete all as specified and directed

Fixing only, after cleaning old steel water tubing, 20mm bore and connections in new or old position using new fittingscomplete all as specified and directed

M & L for 18-20mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, win dow-cills, cooking plat forms and like in cement mortar (1:4) including point ing in white cement (1:2) us ing marble dust with admix ture of pigment to match with shade of granite complete all as specified and directed.

S&F Wash hand basin, flat back 550x400mm vitreous china (white) including PTMT waste fittings, 32mm bore size, waste pipe, PVC, 32mm bore, angle iron/cast iron brackets of required size as directed & making good disturbed surfaces to match with the existing as in repair complete all as specified and directed.

S&F in repair PVC low level flushing cistern (white) of 10 liters capacity with inlet ball float valve, PVC flush pipe and necessary fixing arrangements and connecting to water pipe and WC etc complete all as specified and directed

S&F Vitreous china white squatting pan orrissa pattern of size 580mm x 440 mm with integral foot rests including necessary lime concrete and 100 mm bore cast iron ‘P’ or 'S' trap with 550 to 600 mm long neck for connecting WC to branch piece with cement joints, fixed as in repair, complete all as specified and directed

S&F in repair Viterous China wash down water closet pan (pedestal pattern), white incl. Seat and cover (excluding fixing bolts, flushing cistern and flush pipe) complete all as specified and directed

S&F in Repair to Vitreous China Urinal, Half stall type, white (excluding flushing cistern, flush pipe and waste pipe) including providing and fixing plugs, bedding urinal agianst wall in cement mortar 1:2 securing urinal to plugs with and including 60mm long brass screws, pointing aroiund urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipee. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe) complete all as specified and directed

S&F in repair 15 mm bore Bib tap cast copper alloy chomium plated with crutch or butterfly handle, screwed down,screwed for iron pipe or for brass ferrule. complete all as specified and directed

S&F in repair 15mm bore pillar tap, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly-nuts, screwed for iron pipe, complete all as specified.

S&F in repair stop cock/ angle cock standard 15 mm cast copper alloy cromium plate screwed down high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and directed

S&F in repair 20 mm gun metal,globe or gate valve, with iron wheel head , screwed both ends for iron pipe complete all as specified and directed

S&F PVC connections 15mm size with PTMT nuts of length 450mm complete all as specified and directed

S&F in repair Rotational moulded Polyethylene water storage tank of 500 litres capacity (cylindrical vertical with closed top) hoisted and fixed in position including 20mm PVC float valve high pressure with polythene float valve & taking down old PVC water tank complete all as specified and as directed

Taking down eaves gutters and rainwater pipes(any size or pattern), including all fittings, heads, shoes, bends, swan-necks etc complete all as specified and directed.

S&F in 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls including distance pieces and stack clamps as in rain water pipes as complete all as specified and directed

S&F 110 mm bore PVC (SWR) bends/shoe any radius fixed to walls including distance pieces and stack clamps complete all as specified and directed

S&F 110 mm bore PVC (SWR) tee any radius fixed to walls including distance pieces and stack clamps complete all as specified and directed

S&F 75mm dia PVC (SWR) pipes single socketed in any length with rubber ring jointsfixed to walls complete all as specified and directed.

S&F 75mm dia PVC (SWR)with access door bends any radius complete all as specified and directed.

S&F in repair grating doom 100 mm dia of PTMT (Minimum weight 25 gms) complete all as specified and directed

S&F PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and directed

M&L for cement concrete 1:2:4 type B1 using 20mm graded aggregate as in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves, lintel band and similar articles with plain faces and necessary formwork complete all as specified and directed

S&F for Health Faucet (ABS Body) mild steel chromium plated suitable for 15mm dia pipe with 1.25mm long flexible tube and ABS wall hook including making connections and fixed in position ccomplete all as specified and directed. (Make:Cera/Parryware)

M/s S B Construction Company (BID ID -3262549)

M/S Yashpaul Gulati (BID ID -3261638)

M/s Sidhu Bros (BID ID -3262572)

manoj and company (BID ID -3261765)

M/S N Maini Constrution (BID ID -3261789)

SATIJA BUILDERS (BID ID -3262114)

Vee Vee Enterprises (BID ID -3261629)