ADDL/ALTN TO JCOs/OR MARRIED ACCN AT CERTAIN LOCATIONS AT HISAR MIL STN (PH-I OF TWO PHASES)

Amount

Taking down chowkats or frames with shutter (without taking off shutter from the frames) n. exc 1.50 Sqm each complete all as specified and directed.

Taking down chowkats or frames with shutter (without taking off shutter from the frames) exc. 1.50 Sqm and n.exc 4 Sqm each complete all as specified and directed.

S&F Solid PVC Door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing complete all as specified and directed.

S&F pressed steel frames of size 105x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc. complete all as specified and directed.

S&F pressed steel frames of size 125x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc. complete all as specified and directed.

S&F cupboards/wardrobes, factory made, frame shall be of 1.25mm thick pressed steel with PBI sheet of size 90x70mm, shutter shall made out of 1mm thick pressed steel with 06 Nos 100mm long 3.15mm thick steel hinges, standard pattern rim lock with complete locking arrangement including 12mm vertical rod shall be provided (brass mortice lock, vertical type, size 65mm, 2 levers, ISI marked with escutcheon plate and two keys) with & including two coats of spray painting with synthetic enamel paint of approved tint over a coat of red oxide primer including fixing with minimum 6 Nos 12mm dia mild steel bolt 150 mm long grouted in brick wall/concrete including making good the disturbed surfaces as original with CM (1:4) or PCC (1:2:4) type B0 complete all as specified and as directed. Note :- The measurement shall be taken of front elevation and not girthwise.

S&F 30mm thick factory made flush door shutters, soild core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

S&F 35 mm thick factory made 2nd class hardwood glazed and skeleton shutters, open rebated and prepare to receive glass, gauge etc (with sash bars) edges but divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers as specified in SSR Part-I Section 8 Clause 8.24(a), fitted to chowkats complete all as specified and directed.

S&F factory made mild steel windows (Box type ) with side hung shutters with glazing bars to receive glass, dovetailed or welded with and including necessary welding, reveting, tower bolt, handle, holdfast, hinges and steel peg stay as per Drg No. CEJZ/TD-2013/01 sheet (1/3, 2/3, 3/3) complete all as specified and directed.

S&F factory made mild steel windows (Box type ) with side hung shutters without glazing bars but including sash bars to receive wire gauge, dovetailed or welded with and including necessary welding, reveting, tower bolt, handle, holdfast, hinges and steel peg stay as per Drg No. CEJZ/TD-2013/01 sheet (1/3, 2/3, 3/3) complete all as specified and directed.

S&F factory made mild Steel ventilators with top hung shutter (Box type) to receive glass or wire guage and steel peg stay with and including necessary welding, reveting, tower bolt, handle, holdfast & hinges complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

M&L Mild steel framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks, hand rails, cupboards frame and similar work con- forming to Fe.290.Gde-E-165 with and including necessary cutting and welding complete all as specified and directed.

M&L for preparation of new or previously untreated wooden surface of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L for preparation of new or previously untreated steel surface of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L for PCC 1:2:4 type B0 (using 12.5mm graded crushed stone aggregate) as in steel chowkhats, hold fasts and bed blocks etc including necessary form work complete all as specified and directed.

S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with and including stainless steel wire staples complete all as specified and directed.

S&F sheet glass 4.00 mm thick ordinary quality and glazing with oil putty & necessary screwing / cliping in square/ rectangle n.exc 0.5 Sqm in each pane complete all as specified and directed.

S&F figured glass 4.00 mm thick, pin head type and glazing with oil putty & necessary screwing / cliping in squares/rectangle exc 0.5 Sqm in each pane complete all as specified and as directed and directed.

S&F stainless steel butt hinges, medium weight of size 100 mm fixed with stainless screws complete all as specified and directed.

S&F 250 mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts & sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed.

S&F 200mm size aluminium anodised, barrel tower bolt of extruded section complete all as specified and directed.

S&F extruded aluminium alloy handles 150 mm long fabricated type anodised complete all as specified and directed.

S&F 100mm long aluminium anodized floor door stopper double legged with rubber shoe, fixed to bottom rail of door complete all as specified and directed.

S&F mild steel 300mm, ordinary rat rail rod pattern springs, including roller and roller plate complete all as specified and directed.

Demolition of unreinforced cement concrete of any description and in any position not otherwise specifically provided complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L for PCC 75mm thick (1:3:6) Type-C-2 (using 40mm graded crushed stone aggregate) as in plinth protection including finishing cement concrete surface even and smooth complete all as specified and directed.

M&L for PCC 50mm thick (1:2:4) Type-B-2 (using 40mm graded crushed stone aggregate) as in sub base of flooring complete all as specified and directed by Engr-in-Chargre.

M&L for PCC 25mm thick (1:2:4) Type-B-0 (using 12.5mm graded crushed stone aggregate) as in sub base of flooring complete all as specified and directed by Engr-in-Chargre.

M&L for non skid ceramic tiles,premium quality, coloured pattern as required of 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with laid over and including 15mm thick screed bed in CM (1:4) compete all as specified and directed.

M&L for non skid coloured designer ceramic tiles,premium quality, 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with laid over and including 15mm thick screed bed in CM (1:4) compete all as specified and directed.

-ditto- all as per item No.33 above but on skirting laid over and including 10mm thick backing coat in CM 1:3 complete all as specified and directed.

M&L for glazed ceramic coloured tiles,premium quality, of size 450 x 300 x 7 mm thick on vertical surfaces as in dado etc set and jointed in neat cement slurry and pointed in white or colour cement to match laid over and including 10mm thick backing coat in CM 1:3 and complete all as specified and directed.

M&L for Granite (of any type), 18-20 mm thick machine cut , laid in floor bedded and jointed with grey cement slurry, and pointed with white cement with admixture of pigment to match the shade of the granite stone including cutting grinding and polishing, laid over and including 15mm thick screed bed or bedding layer in cement mortar 1:6 complete all as specified and directed.

M&L for Granite (of any type), 18-20mm thick machine cut, in skirting/ dado and jointed with grey cement slurry, and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete with and including backing coat in 10mm thick CM (1:3) to receive granite complete all as specified and directed.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc laid, bedded and pointed in any mortar complete all as specified and directed.

M&L for Machine cut kota stone slab flooring 18-20mm thick of size not less than 0.30 Sqm of each slab over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing laid over and including 15mm thick screed bed or bedding layer in cement mortar 1:6 complete all as specified and directed. (Note : Single piece tiles will be placed on the surface of stair case tread area).

M&L for Kota stone slab 15mm thick in riser of bricks steps & riser of staircase , skirting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing with & including backing coat in 10mm thick CM (1:3) to receive Kota Stone complete all as specified and directed (Note : Single piece tiles will be placed on the surface of stair case riser area).

M&L for rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified and directed.

Demolition of reinforced cement concrete of any descritption and in any position not otherwise speccifically provided for complete all as specified and directed.

S&F TMT Mild Steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, less than 0.9mm dia or securing with clips complete all as speciied and directed.

M&L for Reinforced Cement Concrete (design mix) M30 using 20mm graded crushed stone aggregate in Slabs supported on walls,plinth beams, beams, lintel bend and columns in floors,roofs, landings, balconies,canopies, deck slabs and in shelves and the like including necessary formworks complete all as specified and directed.

M&L for precast RCC 1:2:4 type-B1 (using 20mm graded crushed stone aggregate) as in manhole and drain cover slab and similar article with plain faces, set in cement 1:4 including necessary form work complete all as specified and directed.

Use and waste of formwork to soffits of suspended slabs such as roof slab, floor slabs, landigs, shelves and similar work, not exc 200mm thick rough finished flat surfaces of concrete complete all as specified and directed.

Dismantling brick tiles or terracing tiles, single layer on roofs complete all as speified & directed.

Demolition of mud in roofs, any thicknes, including plastering and leeping (whether full thickness removed or only or part thereof) complete all as speified & directed.

M&L for preparation of roof surfaces (old or new) with wire brush drying and cleaning to remove all foreign materials and washing with water to remove loose particles with and including providing 50 mm average thick PCC 1:2:4 type B-0 (using 20mm graded crushed stone aggregate) with maintain the proper roof slope complete all as specified and directed.

M&L for providing 10mm thick polymer modified plaster in ratio 1:10 (1 part of polymer and 10 parts of cement with solid contents not less than 30%) over slab and applying priming coat of epoxy primer with resin and hardner with water dilution as per manufacturer instructions, applying 1st coat of solvent based polyurathene liquid membrane not less than 500 micron thick UV stable having SRI value greater than equal to 105 with consumption of 0.61 Kg/Sqm and applying 2nd coat solvent based polyurathene liquid mambrane not less than 500 micron thick UV stable having SRI value greater than equal to 105 with consumption of 0.61 Kg/Sqm over dried 1st coat complete all as specified and directed. Make : M/s Asian Paints Ltd. / M/s STP Ltd/ M/s Sika India Pvt. Ltd.

M&L for Providing cement concrete 1:3:6 type C-1 using 20 mm graded crushed stone aggregate as in roof kerbs complete all as specified and directed.

S&F in repair vitreous China, squatting pan, Orissa Pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) with PTMT trap of suitable size ( P or S type) including connection to trap and to flushing pipe, anti syphonic pipe etc complete including provision of cement concrete bedding & making good to floor complete all as specified and directed .

S&F in repairs 10 Ltr capacity PVC valveless syphonic action type flushing cistern low level white, with inlet, ball valve, float and handle including PVC flush pipe and brackets complete fixed in wall and floor to trap of WC as reqd complete all as specified and directed.

S&F vitreous china wash hand basin, white, flat back, size 550mm x 400mm with & including a pair of pre-painted cast iron brackets (02 Nos of suitable size) & necessary cutting & pinning for fixing of brackets in blocks (PCC 1:3:6 type C1 of size 10x7.5x15cm) with & including CP waste coupling and PVC waste pipe of suitable size (excluding tap, waste chain & plug), complete all as specified.”

Taking up or down 15 mm bore steel tubing and connections from any position with or without concealed type fixed, including cleaning for refixing or removal to store complete all as specified and directed.

S&F 15 mm bore steel water GI tube medium grade with all fittings and fixed with or without concealed to walls, ceilings or laid in floors complete all as specified and directed.

Re-fixing old 15mm bore steel water GI tube medium grade with all fittings / connection in new or old position and fixed with or without concealed to walls, ceilings or laid in floors complete all as specified and directed.

Taking up or down 20 mm bore steel tubing and connections from any position with or without concealed type fixed, including cleaning for refixing or removal to store complete all as specified and directed.

S&F 20 mm bore steel water GI tube medium grade with all fittings and fixed with or without concealed to walls, ceilings or laid in floors complete all as specified and directed.

Re-fixing old 20mm bore steel water GI tube medium grade with all fittings / connection in new or old position and fixed with or without concealed to walls, ceilings or laid in floors complete all as specified and directed.

M&L for Cutting chases into brick walls, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth complete all as specified and directed.

S&F Stop valves of size 15mm dia fancy type, chromium plated with long shank and cup (concealed type), screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

S&F 15mm dia CP angle valves complete all as specified and directed. Cat Part No. MQT-526KN of ESSCO Jaguar or equivalent cat part No of make specified in Appx 'B',

S&F Wall Mixer 3-in-1 System with 115 mm Bend Pipe & Aerator complete all as specified and directed. Make : Cat No. MQT-519KN of ESSCO Jaguar or equivalent cat part No of make specified in Appx 'B',

S&F CP Central Hole Basin Mixer with ‘U’ shape Round Casted Spout with 450 mm Long Braided Hoses complete all as specified and directed by Engr-in-Charge. Make : Cat No. TQT-516A of ESSCO Jaguar or equivalent cat part No of make specified in Appx 'B',

S&F in repair 15 mm dia bib tap ( fancy type) , chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S&F 15 mm dia Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixedcomplete all as specified and directed.

S&F 20 mm dia Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixedcomplete all as specified and directed.

S&F CP soap dish fixed to plugs with chromium plated brass screws complete all as specified and directed. Cat Part No. BA-05 of Make : Prayag or equivalent cat part No of make specified in Appx 'B',

S&F brass chromium plated shower roses of size 125mm with or without swivel joints, any size, including shower arm 15mm size, 195mm long with bend of 45degree with flange of CP fixing to steel pipe or union complete all as specified and directed.

S&F stainless steel CP peg set 6 complete all as specified and directed.

S&F 15 mm dia PVC connections, 450 mm long with PTMT nuts of suitable size at two end complete all as specified and directed.

S&F brass chromium plated Tubular towel rail, 20mm dia, D type, 60cm long between flanges, fixed with screws complete all as specified and directed.

S&F Curtain rod/drapery rod, 20mm dia, mild steel powder coated with and including fency type PVC bracket 2 Nos of each opening and side stopper fency type powder coated of required shape and size 2 Nos of each opening complete all as specified and directed.

S&F in repair multi PVC (SWR) floor trap 75mm dia, with grating including joining to waste pipe with solvent cement, fixed in cement concrete type B-1 (1:2:4) using 20mm graded broken stone aggregate complete all as specified and directed.

Dismantling of cast iron pipes any size of bore as in soil waste or vent pipe including removal of cement joints fixed to wall or laid in floor and taking out of trenches, if required complete all as specified and directed.

S&F 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls & floors with necessary MS clamps complete all as specified and directed.

S&F 75 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls & floors with necessary MS clamps complete all as specified and directed.

S&F 110 mm bore PVC (SWR) access door bends any radius complete all as specified and directed.

S&F 75 mm bore PVC (SWR) access door bends any radius complete all as specified and directed.

S&F 110mm PVC (SWR) junction single,(Single T) equal or unequal provided with access door complete all as specified and directed.

S&F 75mm PVC (SWR) junction single,(Single T) equal or unequal provided with access door complete all as specified and directed.

S&F 110mm bore PVC (SWR) vent cowl complete all as specified and directed.

Demolition of brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed.

M&L for brick work with sub class 'B' bricks straight or curved in plan exc 6 mtr mean radius built in CM (1:4) using old size bricks complete all as specified and directed.

M&L for brick work with sub class 'B' bricks old size straight or curved on plan to any radius in half brick thick wall built in CM 1:4 complete all as specified and directed.

Taking down cement plaster of any description including raking out joints, hacking for key, scrubbing down with water etc. from wall & ceiling surfaces complete all as specified and directed.

M&L for rendering 15 mm thick in CM 1:6 on fair face of brick /concrete surfaces of any description and finishing the surfaces even and smooth without using extra cement complete with complete all as specified and directed.

M&L for preparing new plastered or unplastered surfaces of walls and applying two coats of oil bound distemper over a coat of primer of same make over 2mm thick wall care putty complete all as specified and directed.

M&L for preparing old plastered or unplastered surfaces of walls and applying two coats of oil bound distemper over a coat of primer of same make over 2mm thick wall care putty with and including complete removal of existing treatment of any layer of wall complete all as specified and directed.

M&L for preparing new plastered or unplastered surfaces of walls and applying three coats of white wash on undecorated surface complete all as specified and directed.

M&L preparing old plastered or unplastered surfaces of walls and applying two coats of white wash on old decorated surface with and including complete removal of existing treatment of any layer of wall complete all as specified and directed.

M&L for rendering 5mm thick in CM 1:3 as in ceiling/landing etc on concrete surface finish even and smooth without using extra cement complete all as specified and directed.

M&L for preparing new plastered or unplastered surfaces of ceiling and applying three coats of white wash on undecorated surface complete all as specified and directed.

M&L for preparing old plastered or unplastered surfaces of ceiling and applying two coats of white wash on old decorated surface with and including complete removal of existing treatment of any layer of ceiling surfaces complete all as specified and directed.

M&L for rendering 15 mm thick in CM 1:4 with and including mixing of liquid WPC of approved make @ 200ml per bag of cement / manufacturer's instructions on brick/concrete wall surfaces of any description and finishing the surfaces even and fair complete all as specified and directed.

M&L rough cast plaster as specified (rendering coat not less than 10mm thick in CM 1:3, while it is still in plastic state the rough cast mixture consisting of crushed stone or fine gravel aggregate size 6 to 12mm mixed with coarse sand and cement in the ratio of 1:1:1 shall be applied and finished even) on external wall upto cill height complete all as specified and directed.

M&L for preparing new plastered or unplastered surface of walls and applying two coats of weather proof paint over a coat of paint base primer of same make complete all as specified and directed. Note :- The work under this item shall be carried out by the contractor from authorised applicator of the manufacturer by using modern technique. The contractor shall also furnish guarantee of the quality and finish work under this item for a period of 05 years from the certified date of completion of work for which an amount equal to Rs 5% of cost of executed item shall be retained in final bill. This amount shall be returned only after completion of guarantee period.

M&L for preparing old plastered or unplastered surface of walls and applying two coats of weather proof paint over a coat of paint base primer of same make with and including complete removal of existing treatment of any layer of wall complete all as specified and directed. Note :- The work under this item shall be carried out by the contractor from authorised applicator of the manufacturer by using modern technique. The contractor shall also furnish guarantee of the quality and finish work under this item for a period of 05 years from the certified date of completion of work for which an amount equal to Rs 5% of cost of executed item shall be retained in final bill. This amount shall be returned only after completion of guarantee period.

Dismantling water tank of capacity exceeding 250 litres but not excedding 500 litres complete all as specified and directed.

S&F rotational moulded polythene water storage tank 500 litres capacity (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I complete all as specified and directed.

Disconnecting existing tanks of capacity exceeding 500 litres but not exceeding 1000 Ltrs, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position complete all as specified and directed.

Cleaning and removing all scale and dirt, etc, from tanks of capacity exceeding 500 liters but not excedding 1000 Ltrs and from mouths of circulating pipes, etc. complete all as specified and directed.

S&F in repairs 20mm bore ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight - 210 gms) complete all as specified and directed.

S&F in repairs 20mm bore PTMT nipple suitable for HDPE water tank (Min weight -45gms) fixed complete all as specified and directed.

M&L for preparation of old painted steel or iron surfaces of any description, over 10 cm width or girth and applying two coats of synthetic enamel paint complete all as specified and directed.

M&L for writing letters or figures (Block, Roman, Italic or Indian) n. exc. 30 cm high with synthetic enamel paint all as specified and directed.

S&F sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm, bowl size 410mm x 330mm x 160mm including PTMT waste copupling & waste pipe 900mm long complete all as specified and directed.

Taking down existing serviceable kitchen sink of any size and re-fixing the same after carrying out other B/R repair works including fixing the brackets with cement mortar(1:4) mixed with pigment to match with the existing surface complete to the entire satisfaction of Engineer-in-charge. Note :- Contractor shall kept the sink in safe custody and in case any damage to sink the same shall be provided by the contractor without any extra cost to Govt

S&F Kitchen rack (Overall size 24"x24"x10”) complete all as specified and directed. Make : Cat No. P-310 of Prayag or equivalent cat part No. of make specified in Appendix 'B'.

S&F corner glass shelf 300mm (with brass brackets) complete all as specified and directed as per Cat No. BEA-44 of Make-Prayag or equivalent cat part No. of make specified in Appendix 'B'.

M&L preparation of new or previously untreated steel surface of any description not otherwise described over 10 cm width or girth and applying two coats of black Japan paint over a coat of red oxide primer complete all as specified and directed.

M&L for treatment of sunken floor slab comprising of the following specifications with and including demolition of sunken floors complete all as specified and directed:- (i) Cleaning the sunken/lowered portion of RCC slab surface (including vertical total depth plus skirting height) of floors by wire brush, chisel out any mortar sticking to the surface and brooming completely. Provision of 40mm thick average PCC 1:2:4 type B-0 using 12.5mm graded aggregate as in padding concrete to achieve proper slope including cutting holes in bricks or RCC wall for spout. (ii) Rendering of uneven surfaces with 6mm thick CM 1:4 mixed with and including integral water proofing compound Sika Plastocreat plus or equivalent make in Fosroc / Thremax as approved by GE @ 0.2% by weight of cement consumed including filling it with water to check dampness and seppage and where dampness / seppage is noticed, nozzles shall be fixed and grouting carried out. (iii) All junctions points of side wall where CI/GI/PVC pipes are passing through shall be sealed with epoxy putty Sikaguard 694 F(I) or equivalent make in Fosroc / Thremax as approved by GE. (iv) After drying putty, wash the slab and sides of sunken portion with water and make it clear and clean.

(v) Applying two coats of polymer modified cementious water proof coating with Sika Topseal 107 or or equivalent make in Fosroc / Thremax as approved by GE in two coats @ 3kg/sqm to sanwiched with glass fibre reinforcemnt: Sika Fab-1 or or equivalent make in Fosroc / Thremax as approved by GE over base coat as per mnaufacturer's instruction to bottom and vertical sides up to finished floor level+100mm height. The thickness of two layer shall be 1mm. When the second layer is still sticky, coarse sand spray shall be carried for the vertical and bottom surface of the sunken portion. (vi) Plaster the bottom and sides up to bottom of the skirting with minimum 20mm thick CM 1:4 mixed with integral water proofing compound SIKA plastocreat plus or equivalent make in Fosroc / Thremax as approved by GE @ 0.2% by weight of cement consumed as per manufacturer's specification including rounding of corners and injuctions sloping towards spout. (vii) All pipes laid in sunken portion shall be covered with 50mm thick PCC 1:3:6 all round after painting with anticorrosive paint . (viii) The sunken floor shall be filled with lean cement concrete 1:7:12. Note :- Test the water proofed area (ponding test) by filling water for at least 72 hours and tested for leakage seepage and to the entire satisfaction of GE. Test record for each sunken slab shall be maintained. The treatment shall be carried out by authorised applicators of chemicals. Cost of testing and all M&L is inclued in the rates quoted above. For payment purpose, the plan area of sunken floor shall be taken into account

Chipping of loose/ damaged /cracked / previously repaired / delaminated or weak concrete by chieseling to expose the sound core concrete where ever required and to expose rusted reinforcement upto depth n.exc 50mm and disposal of rubbish off the premises to a distance not exc 50 mtrs including cleaning of reinforced concrete surface by air compressor complete all as specified and directed.

Supply and apply of rust remover cum passivator to remove rust from existing reinforcement by using product: Rustoff-100 of Sika or equivalent make in Fosroc/ Thermax as approved by GE, with density 1.01 Kg/ltr at 30 degree celsius and consumption : 0.2 Kg/Sqm/coat complete all as specified and directed. Note: The material to be applied thoroughly on exposed rebars only with the help of a brush of suitable size. The area will be measured as length of bar x two times the dia of bar).

Supply and apply a cement based polymer modified rebar corrosion protection system to existing reinforcement using cement based polymer modified rebar corrosion protection system with consumption : 3.75 kg/Sqm for two coats and Product requirements: carbonation resistance: 2 mm of SikaTop Armatec®-108 of Sika or equivalent make in Fosroc / Thermax as approved by GE corresponds to 20 mm of normal mortar; bond strength > 1N / Sqmm according to ASTM C 882-78 complete all as specified and directed. Note: The material to be applied thoroughly on exposed rebars only with the help of a brush of suitable size. The area will be measured as length of bar x two times the dia of bar)

M&L for Providing, mixing & applying two component Epoxy resin concrete Bonding coat on prepared RCC surfaces as per manufacturer's specification including prepartaion of surface throughly and cleaning complete where ever required with using Product: Sikadur®-32 LP of Sika or equivalent in Fosroc / Thermax as approved by GE with Consumption: 0.4 kg/Sqm and Product requirements: Complies with ASTM C 881-78, Type II Grade 2 Class B+C complete all as specified and directed.

M&L for providing by mixing and trowel application of prepacked, light weight, two component structural grade polymer modified fibre reinforced thixotropic cement mortar Sika Monotop 122F of Sika or equivalent make in Fosroc / Thermax as approved by GE at an average thickness exceeding 10mm and upto 25mm to the prepared concrete surface in soffit of slabs, beam, columns, parapets, fins and facias at any height, including finishing of applied Polymer mortar as per the technical specifications and manufacturer's instructions complete all as specified and directed .

M&L for weld-mesh of size 75x75x3mm to be wrapped on the exposed surface of rib of beam & on the slab bottom and tack welding to the exposed reinforcement at close intervals and gunite with cement mortar 1:3 mixed with admixture Sika Plasto creat plus or equivalent make in Fosroc / Thermax as per manufacturer's instructions as approved by GE around rib of beam or roof slab of thickness n.exc 40mm to be applied under an operating pressure. The gunited surface to be cured properly for a min of 7 days all in complete as per the technical specifications and manufacturer's instructions and directed.

Providing and fixing water tight centering & shuttering and Scaffolding including bolting, strutting, propping etc. including removal of form work from column, beam , slab etc. complete as per site requirement and directions of Engineer-in-charge.

Supply and apply a ready to use non shrink, cementitious free flow micro-concrete (<100 mm) using Product: SikaRep® Microcrete-4 + adequate coarse aggregate, Yield: approx 17 Ltr/bag (30 Kg) (depending on the size and quantity of coarse aggregate added), Product : SikaRep® Microcrete-4 or equivalent make in Fosroc / Thermax as approved by GE, Product requirements: compressive strength > 60 N/Sqmm (28 days) according to ASTM C 1107-99 complete all as specified and directed.

M&L for providing and fixing 12-16mm dia injection ports non returnable nozzle by drilling, cleaning and sealing holes 50-75 mm deep at 200mm c/c with fast setting high strength Epoxy putty, solvent free, three component compound based on epoxy resins, graded fillers and thixotropic agents using Sikadur 31 of Sika or equivalent make in Fosroc / Thermax as approved by GE as in beams, columns, slab and parapets as per the technical specifications and manufacturer's instructions complete all as specified and directed.

M&L for grouting of nozzles with low viscous moisture insensitive, High strength, epoxy resin grout with Sikadur 52 LP (IN) of Sika or equivalent make in Fosroc / Thermax as approved by GE with pressure not excedding 2-3 Kgf/Sqcm till the nozzle refuses to take further grout including cutting extra length of the nozzle after the grout hardens and finishes as per the technical specifications and manufacturer's instructions complete all as specified and directed.

Cutting holes into or through cement concrete slabs and cutting through reinforcement chajjas, etc reinforced or other wise surfical area exc 100 sqcm but n.exc 250 sqcm as directed to insert angle iron for holding chajjas / coller platforms as required complete all as specified and directed.

M&L for preparation of old painted wooden surface of any description and applying one coat of synthetic enamel paint, over 10cm width or girth complete all as specified and directed.

S&F TMT bars 5mm dia and over upto and including 10mm dia as in stirrups, spaces and binders in reinforcement, cut to length, bent to shape required including cranking, bending spirally or hooping for columns & beam, hooking ends and binding with MS wire (annealed not less than 0.9mm dia) all as specified and directed.

S&F mild steel Joist, channel, angle or tee sections, fixed independently, without connecting plates, etc (cut to ordinary lengths i.e. within 20mm of the length indicated), for cooler stand, chajjas and other smilar works complete all as specified and directed conforming to Fe 410-W (Gde-E-250) quality -A).

S&F pre-painted galvalume aluminium zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall and in chajjas, fixed with self tapping screws complete all as specified and directed.

Removing all disintegrated and loose concrete of any thickness including plaster if any in RCC Column, Chajja, slab, beams, lintels etc, removing all loose rust/scale form exposed reinforcement bars by using wire brushes and sand paper including cleaning of exposed reinforcement bars by using wire brushes and sand paper including cleaning of exposed surfaces of reinforcement with protective anti corrosive epoxy bonding chemical (Make : Pidilite) and including tied reinforcement bars / IRC fabric 50mm x 50mm x 12guage if required to reinforcement concrete bonding primer uniformly to exposed surfaces and applying cement mortar 1:3:1 with WPC (1 Part Cement : 3 part sand : 1 part 6mm coarse aggregate) to an average thickness not less than 20mm and removing debris outside MD land complete all as specifeid and directed.

S&F rolled mild steel framed work as in doors or gates of angle or other section conforming to FE-410-W (Gde-E-250) Quality A, with gusset plates, rails braces, etc complete drilled for fixing of sheets and including steel sheeting or other covering and hanging and fixing complete as in garrage door and roof access door complete all as specified and directed.

Taking down carefully surface/ concealed copper/aluminium point wiring (light,bell,fan,socket or power) complete, including taking out existing unserviceable terminal boxes and conduit with fixtures and fittings such as switches,ceiling roses,lamp holders,pendants,sockets, regulators,tube light fittings brackets light fittings, rectngular blocks DB, MCCB etc and making good disturbed surfaces of walls, floors etc complete all as directed by Engineer-in-Charge.

M&L for point wiring with 1100 volts grade PVC insulated unsheathed FRLS single core multistranded copper conductor cable 1.5 sqmm (Phase-Red,Neutral-Black) and earth continuity conductor 1.5 Sqmm FR single core (Green) drawn into and including concealed rigid non metallic PVC conduit medium grade not less than 20mm dia ISI marked ivory colour with all conduit fittings/fixing accessories and unwelded sunken galvanized pressed steel terminal boxes of thickness not less than 1.2mm covered with 3 mm thick phenolic laminated white sheet cover for mounting switches including repairing the surface with CM 1:3 and finishing the surface as per exisitng treatment and as required for the following:-

One light point controlled by one switch

One fan/exhaust point controlled by one switch

One bell / buzzer point controlled by one bell push.

One 3 pin socket outlet 5 amps point controlled by one switch on independent board

M&L for point wiring with 1100 volts grade PVC insulated unsheathed FRLS single core multistranded copper conductor cable 4 Sqmm (Phase-Red,Neutral-Black) and earth continuity conductor 4 Sqmm FR single core (Green) drawn into and including concealed rigid non metallic PVC conduit medium grade not less than 20mm dia ISI marked ivory colour with all conduit fittings/fixing accessories and unwelded sunken galvanized pressed steel terminal boxes of thickness not less than 1.2 mm covered with 3 mm thick phenolic laminated white sheet cover for mounting switches, socket as required for one 3 pin 15 Amps socket outlet point controlled by one, one way switch on independent board complete all as specified and directed.

S&F Switch piano, flush type, single pole, one way 5/6 Amp 230 volts AC complete all as specified and directed.

S & F switch piano, flush type, single pole, one way 15 Amp, 230 volts AC complete all as specified and directed.

S & F Bell push, flush type, 5 amp 230 Volts AC complete all as specified and directed..

S & F Socket outlet multipurpose, 5 pin, 5 amp flush type 230 volts, AC, complete all as specified and directed.

S & F Socket outlet multipurpose 2 in 1 , 3 pin, 6 and 16 amp flush type 230 volts,AC, complete all as specified and directed.

S & F lamp holder insulated polycarbonate body with back plate 230V AC complete all as specified and directed.

S&F ceiling rose surface backelite 65 x20mm three terminal, polycorbonate body with back plate 230V, AC complete all as specified and directed..

S & F electronic stepped type fan regulator 230 AC volts suitable for 1200/1400 mm sweep ceiling including connecting up complete all as specified and directed.

Supply and fix LED bulb of capacity 5W with minimum output 120 luminaire per watt suitable for holder 230 V AC all as specified and directed.

Supply & Fixing LED light Fitting 1x18/20/22W, regal batten for LED including ultra bright glass LED tubelight with very high efficiency single/double side connection all as specified and directed Cat part No LUMLINESBS20WLED865SPCWH of make Havells, Surya Cat part No SLE BT 20 MS for batten and IED tube rod SLE TL-DS 18 PC Reform of Surya and C &S Cat No LTTB4F20WLEDEWBATTEN for batten and Tube rod cat No LT4F20WLEDT8/WDI.

Supply & Fixing LED bulk head light Fitting 1x10/12W, environment friendly, ultra modern, energy saving, surface mounted decorative oval bulk head edge-lit LED luminare comprising of high brightness model Endura rugby Neo IP-65 complete fittings all as specified and directed of Cat par No HEXAFT10WLED857SSYMBOPC of make Havells or equivalent Cat part No of make specified in Appendix 'B'.

S&F factory made, sheet metal enclosure distribution boards double door powder coated, protection class IP-42 suitable for mounting MCB, DBs conforming to IS-13032, IS-8623, BS-5484 with min 200 Amps rating copper bus bar, SP& N 8 Ways complete all as specified and directed.

S&F sheet metal enclosure distribution board VTPN, 8 way, double door powder coated, protection class IP-54, isolated neutral bar, mechanical impact strength IK 09 suitable for mounting MCB / MCCB DBs confirming to IS-13032, IS-8632, BS 5484 with min 200 Amp rating copper bus bar and grouting, fixing on wall with nut, bolts washers proper with PCC works complete all as specified and as directed by Engineer-in-Charge.

S & F MCBs SP 6 to 32 amps having rupturing capacity 10 KA, IS-8828 marked including required wiring connections with copper lugs of suitable size provided in MCB DBs complete all as specified and directed. Note : Make of MCB should be the same make as that of DB.

S & F MCBs SPN 32 to 63 amps having rupturning capacity 10 KA, IS-8828 marked including required wiring connections with copper lugs of suitable size provided in MCB DBs complete all as specified and directed. Note : Make of MCB should be the same make as that of DB.

S & F MCCBs Four pole 63 amp having rupturing capacity 16 KA, IS-8828 marked including required wiring connections with copper lugs of suitable size provided in MCCB DBs complete all as specified and directed. Note : Make of MCCB should be the same make as that of DB.

Supply & fixing of Buillding security light fitting LED 18/20W with minimum output 120 luminaire per watt, pressure die cast housing epoxy powder coating IP-65, connected with and including 0.5 sqmm flexible copper multistranded conductor cable including security light bracket made to shape out of GI pipe 25 mm bore light grade, 1.5 mtr length and fixed with MS calmps of size 40x5 mm- 02 nos, nuts, bolts and washers on wall complete all as specified and directed.

M&L for submain wiring with PVC insulated FRLS multistranded copper conductor cable of size 2x6.0 Sqmm drawing into and including rigid non metallic PVC conduit, medium grade not less than 20mm dia ISI marked ivory colour with all conduit fittings and fixing accessories and 6.0 Sqmm FRLS multistranded copper conductor cable as continuous earth wire complete including taking down existing unserviceable submain wiring all as specified and directed. (Note :- two runs of 6 Sqmm copper wire and one run of 6 sqmm copper earth wire alongwith PVC conduit shall be meausred as one unit)

S&F ceiling fans complete with electroic type regulater and accessories 230V/240V, 1200 mm sweep BEE 5 star rated, AC single phase complete all as specifed and directed by Engineer-in-Charge.

S & F Bell ding dong , AC, 230 volts, single pole suitable for married accn complete all as specified and directed.

Supply, installing, testing and commissioning water heater (geyser) 25 ltr capacity standing loss less than 0.562kwh per day for 45 degree centigrade difference of temperature as per IS 2082 (5 star rated as per BEE), reheating time less than 60 minute, mixing factor less than 20%, sock proof high density PUF insulation body material, glass lined inner tank material having warranty 7 years on tank material, 4 years on glass coated heating element, 2years on products including comprising following fittings:- (a) glass coated incoloy element. (b) capillary type thermostat ( c) Digital display unit (d) Thermal cut out ( e) Multifunctional valve (f) Earth leakage circuit breaker (g) Magnesium anode rod cathodic protection (h) Flexible cable of suitable length with 3 pin plug of 16 Amp capacity (i) Drain plug (j) Fusible plug fitted on the crown of water heater with operating temperature 40 degree centigrade to 75 degree centigrade with ideal for pressure 8 bar or more including fixing by grouting and fastener complete all as specified and directed by Engineer in Charge

Supply and fixing steel exhaust fans 300 mm sweep refresh air DXW 230/240 volts, AC single phase with louver including cutting hole in the wall and making good the same as per existing surface complete all as specified & directed by Engineer-in-Charge.

M & L in replacement of Earthing complete with galvanized steel earth plate electrode 60cmx60cmx 6.0 mm thick burried directly in ground (earth pit not less than 2.25 mtrs deep below normal ground level) with top edge of the plate not less than 1.5 mtrs below normal ground level, the earth electrode surrounded from all sides with adequate quantity of mixture of charcoal and common salt and connected to galvanised earth lead wire 4.00 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel protected by galvanised iron medium grade 15 mm bore pipe and GI Pipe 20 mm bore medium grade for water filling including 15x20 mm reducer socket funnel wire mesh, RCC cover PCC chamber pit with PCC (1:3:6) type C-2 excavation and earth work, disposal of surplus spoil, to a distance not exceeding 50 mtrs all as specified and shown on electrical plate No. 3 of SSR (Part-I) complete all as specified & directed.

M&L for cutting chases in bricks wall/PCC walls for taking out blocked concealed conduited and S&F new PVC conduit not less than 25mm dia with accessories and making good to surface in cement mortar 1:3 with finish to match the existing surface. Note : wiring required for replacement shall be measured and paid separately under respective item.

Taking down ceiling fan/Exhaust fan, sealing cable end, dismantling blades and removing fan and blades and deposited to MES store.

Re fixing only ceiling fan any make or any size and servicing, painting of ceiling fan complete in situ with one coat of synthetic enamel paint by spraying including filling cavities with filler after cleaning all dust etc and writing MES No with black paint all as specified and directed by Engineer-in-Charge.

Re fixing only Exhaust fan any make or any size and servicing, painting of ceiling fan complete in situ with one coat of synthetic enamel paint by spraying including filling cavities with filler after cleaning all dust etc.

Taking out the old unserviceable LT underground cable any size 1100 volts grade, XLPE insulated and PVC sheathed, armoured heavy duty with multistrand aluminium conductors from trenches/wall/floor/road /culverts or pole of following sizes etc complete all as specifed and directed. Note : Excavation and earth work, duct work, GI pipe for laying of cable and sand cushing /cable protection covers etc are beyond the scope of this item and shall be measured & paid for separately.

Supply and laying of LT cable XLPE Insulated armoured heavy duty, electric power cables 1100 Volts grade multistranded aluminium conductor extruded PVC inner sheathed extruded FRLS PVC outer as per IS-7098 of size 25 sq mm 4 core complete all as specified & directed.

Supply and laying of LT cable XLPE Insulated armoured heavy duty, electric power cables 1100 Volts grade multistranded aluminium conductor extruded PVC inner sheathed extruded FRLS PVC outer as per IS-7098 of size 35 sq mm 4 core complete all as specified & directed.

Excavation in trenches not exc 1.5 Mtr wide and not exc 1.5 Mtr depth in any type of soil and getting out complete all as directed.

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exceeding 25 cm thick in any type of soil.

Removing surplus excavated material (soils) to a distance n exc 50 Mtr & depositing where directed a level n. exc 1.5m above the starting point complete all as specified and directed.

M&L for old size sub class 'B' bricks , best quality locally available , laid flat dry laid in trenches flat perpendicular to the direction of the cable for cable protection complete all as specified and as directed.

Taking up only bricks laid as cable covers and stacking serviceable brick for reuse at site etc complete all as specified and directed.

Laying only old bricks retrieved from item No. 169 above as in cable covers in trenches laid flat perpendicular to the direction of the cable etc complete all as specified and directed.

Supply and Filling approved river fine sand in trenches for sand cushion for laying of cables of 8cm below cable and 15 cm above cable and than gently punned down to a depth of 10 cm above cable to the full width of excavated trench , etc complete all as specified and directed. (Note:- Punned thickness 18 cm only be measured for payment purpose)

Supply and laying in replacement of galvanised iron pipe 40mm dia light grade including all fittngs for cable protection fixed to poles under floor/ground including suitable size of clamps, nut & bolts complete all as specified and directed.

Siya constructions

SOM BUILDERS