GE/863/EWS-T-63/2019-20

Amount

Demolition of cement concrete (unreinforcement) of any description and in any position not other wise specifically complete all as specified and directed and directed by Engr-in Charge.

Demolition of cement concrete (reinforcement) of any description and in any position not other wise specifically complete all as specified and directed and directed by Engr-in Charge.

Demolition of Stone/ boulder masonary built in CM incl all quins arches pillars etc complete all as specified and directed and directed by Engr-in Charge.

M & L for plain cement concrete, Nominal Mix (1:4:8) (using 40 mm graded stone aggregate) as in foundation, filling and mass concrete complete all as specified and directed by Engineer-in-Charge.

M & L for mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed by Engr-in-Charge.

M & L for mild steel TMT bars 5 mm dia and over upto and including 10 mm dia as in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed by Engr-in-Charge.

M & L for providing reinforced cement concrete M25 Design Mix using 20 mm graded stone aggregate as in foundation including rafts, footing, foundation beams, plinth beams, bases for columns, basement slabs, under-reamed piles and mass concrete complete all as specified and directed by Engr-in-Charge. (Note :- Reinforcement shall be measured and paid separately under respective item)

M & L for providing reinforced cement concrete M25 Design Mix using 20 mm graded stone aggregate as in walls, retaining walls, basement walls, ballast wall and like complete all as specified and directed by Engr-in-Charge. (Note :- Reinforcement shall be measured and paid separately under respective item)

M & L for walling of random rubble stone masonry, un-coursed, well bonded, bedded, solidly hearted and built in cement mortar 1:6 complete all as specified and directed by Engr-in-Charge.

All as per item No 9 above but except stone using old stones obtained from item No 3 complete all as specified and directed by Engr-in-Charge.

M & L for use and waste of formwork to faces of walls, retaining wall, abutments, parapets, staircase railing and similar works including attached pillasters, buttressess etc in rough finished flat surface of concrete complete all as specified and directed by Engr-in-Charge.

M/L PCC 1:2:4, type B-0 using 12.5 mm graded stone agg as in coping to retaining walls/ steps complete all as specified and directed by Engr-in-Charge.

M&L for 50mm thick cement concrete type C2, 1:3:6 (using 40mm graded stone agg) as in plinth protection finishing fair and even without using extra cement complete all as specified and directed by Engr-in-Charge.

Framed work such as grills, gratings etc., with ends of bars shouldered and/ or riveted, or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 410-0 or Fe 310-0 complete all as specified and directed by Engr-in-Charge.

Rendering 15mm thick on fair faces of PCC block walling in CM 1:4 finished even and smooth without using extra cement complete all as specified and directed by Engr-in-Charge.

M & L for Hardcore of gauge not exc. 63 mm, deposited, spread and leveled in layers not exc. 15 cm thick, watered and rammed to a true surface using broken stone or boulders complete all as specified and directed by Engr-in-Charge.

Material and labour for dismantling the pump from engine, opening the coupling, taking down from the foundation and transporting to workshop. Dismantling the 19 HP multistage water pump head assembly including bearing, multistage impeller assembly neck rings, bushes, coupling assembly,nuts bolts,gasket & washer from the site, replace the worn out multistage impeller, bearing, head assembly incl nut bolts gasket washer,making the pump functional and coupling assembly with prime mover engine and refixing the pump on foundation and testing the pump to achieve desire head & discharge complete all as specified and directed by the Engineer-in-Charge.

Material and labour for drain out the engine oil from Kirloskar Engine of capacity 12 BHP, dismantalling the engine head assembly from the basement of engine, opening the head, dismantling the piston assembly, check the each part of the engine, replacement of unserviceable parts like connecting rod, piston rings,cylinder liner, big end bearing, piston rings, doing leath work on crank shaft, injectng system, and refixing the head assembly in the same positing with gasket complete. Replacement of starter, calibration of the fuel injecting system, replacement of all gasket, servicing, filling of engine oil upto the required level, testing of the engine by run on completion complete all as specified and directed.

S & F in replacement of battery 12V, 80 AH maintenance free complete all as specified and directed by Engr-in-Charge. Approved makes as per Appx 'B' of tender documents.

Material and labour for repair/replacement of 10 HP Monoblock pump, 3 phase, 415V with replacement of worn out copper windings, bearing, machining of rotor, replacement of rubber seal, bronze impeller of pump, machining of casing including greasing etc all as required at site.complete all as specified and directed by Engr-in-Charge.

Supply and fixing in replacement DOL Starter for 10 HP Pumping Set, 415V, 3 Phase complete. Make : Havells/L&T/BCH

Material and labour for repair/replacement of 05 HP Monoblock pump, 3 phase, 415V with replacement of worn out copper windings, bearing, machining of rotor, replacement of rubber seal, bronze impeller of pump, machining of casing including greasing etc all as required at site.

Supply and fixing in replacement DOL Starter for 5 HP Motor 415V, 3 Phase complete. Approved makes as per Appx 'B' of tender documents.

Material and labour for repair/replacement of 02 HP Monoblock pump, 3 phase, 415V with replacement of worn out copper windings, bearing, machining of rotor, replacement of rubber seal, bronze impeller of pump, machining of casing including greasing etc complete all as specified and directed by Engr-in-Charge. Approved makes as per Appx 'B' of tender documents.

Supply and fixing in replacement DOL Starter for Motor 415V, 3 Phase system of capacity 2 HP etc. complete all as specified and directed by Engr-in-Charge. Approved makes as per Appx 'B' of tender documents.

Supply and install Submersible Pumping set non clog type, vertical type, 3 phase 415V inclusive of DOL starter and PCC foundation complete of capacity 5 HP.complete all as specified and directed by Engr-in-Charge. Approved makes as per Appx 'B' of tender documents.

Supply and install Monoblock pump set suitable for 415V, 3 phase having capacity 5 HP complete inclusive of DOL Starter. complete all as specified and directed by Engr-in-Charge. Approved makes as per Appx 'B' of tender documents.

Supply and fixing low density polyethylene pipe (LDPE) with pressure rating 6 Kg/sqcm, bore size 50mm to be fixed on outlet pipe of pumpset.complete all as specified and directed by Engr-in-Charge.

Supply and fixing flexible pipe of pressure rating 6kg/sqcm bore size 80mm dia (3") on suction side with clamp.complete all as specified and directed by Engr-in-Charge.

Supply and fix brass foot valve 80mm (3'') dia.complete all as specified and directed by Engr-in-Charge.

Supply and fix cast iron body sluice valve heavy duty class PN 1.6 flanged ends any pattern with cast iron wheel & mild steel spindle ISI marked confirming to IS-14846 of 2000 for 80mm bore pipe with jointing material, flanged joint, rubber gasket 6mm thick, nuts & bolts, washer complete all as specified and directed by Engr-in-Charge. Approved makes as per Appx 'B' of tender documents.

Supply and fix GI tubing, medium grade galvanised, 80 mm bore with all fittings.complete all as specified and directed by Engr-in-Charge.Approved makes as per Appx 'B' of tender documents.

Supply and fix GI tubing medium grade galvanised 50mm bore with all fittings. complete all as specified and directed by Engr-in-Charge.Approved makes as per Appx 'B' of tender documents.

Supply and fix GI tubing medium grade galvanised 40 mm bore with all fittings. complete all as specified and directed by Engr-in-Charge.Approved makes as per Appx 'B' of tender documents.

Drain out the water from filtration plant, removal of existing gravels substance from the filtration steel tank, brushing, cleaning the internal surface of the tank with chemical agent, refilling the fresh gravels of suitable size and make connection with GI pipe of suitable size from tank to water supply pump Set and pump set to filtration plant complete all as specified and directed by Engr-in-Charge.

S& F Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed of size 50 mm complete all as specified and directed by Engr-in-Charge. Approved makes as per Appx 'B' of tender documents.

S & F cast iron butterfly valve of size 50 mm dia with flanged ends complete all as specified and directed by Engr-in-Charge.Approved makes as per Appx 'B' of tender documents.

Supply and lay Flat type three core PVC insulated & PVC sheathed industrial cable for submersible pump motor and making electric connection.complete all as specified and directed by Engr-in-Charge.Approved makes as per Appx 'B' of tender documents.

Net contract sum will be after deducting Sch of Credit of Rs 14,450.00

Pankaj Builders

M/S Gopal Singh

M/S SHIV NATH ENTERPRISES