SPL REPAIR OF ADM BK T-2 (TILING AND REPLACEMENT OF WOODEN WINDOWS AND FALSE CEILING) AT TECH AREA IN AEC TRG COLLEGE AND CENTRE

Amount

Demolition of cement concrete (unreinforced) in ground floors and paving n exc 15 cm thickness (below or above ground level) complete all as specified and directed.

Dismantling of floor, walls, roof tiles including bedding but backing and rubbish off permises complete all as specified and directed.

M&L for joint free non skid ceramic coloured tiles 7 to 8 mm thick (square / rectangular) area of each tile exc 0.18 sqm & not exceeding 0.38 sqm in floors etc set & jointed in neat cement slurry and pointed with white or coloured cement to matchcomplete all as specified and directed.

M&L for joint free non skid ceramic coloured tiles 7 to 8 mm thick (square / rectangular) area of each tile exc 0.11 sqm and not exceeding 0.18 sqm in floors etc set & jointed in neat cement slurry and pointed with white or coloured cement to match complete all as specified and directed.

M&L for 10mm thick Light shade vitrified ceramic tiles in floors, exceeding 0.36 sqm but not exceeding 0.42 sqm set & jointed in neat cement slurry and pointed in coloured cement to match complete all as specified & directed.

M&L for glazed ceramics coloured tiles of size 450x350x7mm thick in vertical surfaces such as skirting/dados/wall, set and jointed in neat cement slurry and pointed in white or coloured cement to match the surfaces complete all as specified & directed.

M&L for screed bed or bedding layer of mortar 15mm thick for laying floor finishes in CM 1:6 for laying of floor tiles complete all as specified & directed.

M&L 25 mm thick cement concrete (1:2:4), type B-0, using 12.50 mm graded aggregate as in floors including finishing the surface rough & even for receiving kota/tiles complete all as specified & directed.

S&F anodised aluminium frame with powder coating (minimum thickness of powder coating 50 micron) for doors window ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified & directed.

M&L for 10 mm thick plaster in cement mortar 1 : 4 for fixing of wall tiles complete all as specified & directed.

M&L for chequered cement concrete tiles 20cm x 20cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors glossy finished with grey cement and pigment and including screed bed or bedding layer of cement mortar(1:4) 15 mm thick for laying floor finishes

M&L 50 mm thick PCC 1:3:6 type C-2 using 20mm graded aggregate as in plinth protection finishing even & fair without using extra cement laid in bays complete all as specified & directed.

Taking down cement plaster on wall/ceiling/roof etc including raking out joints, hacking for key scrubbing down with water etc complete all as specified & directed.

M&L 15 mm thick rendering on fair faces of bk /concrete surfaces in CM (1:6), finished even and smooth (without using extra cement ) complete all as specified & directed.

M&L for rendering 15 mm thick in cement mortar 1:4, in two layers (1st layer 10 mm thick rendering coat and 2nd layer 5 mm thick finishing coat) on brick work or concrete surfaces, second layer (finishing coat) mixed with liquid water proofing compound @ 200 ml / 50 Kg bag of cement as per manufacturer's instructions and finished the surfaces even and fair without using extra cement complete. Note : Liquid WPC will be measured and paid separately.

Supply only liquid water proofing compound, ISI marked

S& F 5.5 mm thick sheet glass ordinary quality and glazing with oil puty/wooden beading/neoprene beading/ rubber gasket in square n. exc 0.5 Sqm in each pane complete all as specified and directed .

All as per above item No 16 but exc 1.5 Sqm but n.exc. 4 Sqm each complete all as specified & directed.

Taking down shutter of any description n exc 1 sqm each and removing to store complete all as specified & directed.

S & F 35 mm thick 2nd class hardwood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc (without sash bars) edges of framing plain chamfered or rounded fitted with cut and mitred beads for securing glass etc fitted to chowkhats for doors etc complete all as specified & directed.

S & F 30 mm thick 2nd class hardwood glazed and skeleton shutters, for window open rebated and prepared to receive glass, gauze etc (with sash bars) edges of framing plain chamfered or rounded fitted with cut and mitred beads for securing glass etc fitted to chowkhats for window etc complete all as specified & directed.

S & F factory made 35 mm thick plain, framed, panelled shutters (Two panels) with lock rail and panel of 9 mm thick BWP commercial ply or 12 mm thick veneered particle board with commercial veneering on both faces and size of the members of shutter are as per IS – 1003 (Part – I) made of kiln seasoned & chemically pressure treated 2nd class hardwood rail and style complete all as specified & directed.

S & F 30 mm thick flush shutters solid core construction with block board core and plywood face panels, commercial type on both sides supplied and fitted to chowkats complete all as specified & directed.

S&F Mild steel framed works such as grills,gratings,etc, with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work for portions framed and hung as gates, including pintle hinges, stops, hand made sliding bolts, etc conforming to Fe 290 Gde -E-165 complete all as specified & directed.

S&F Plain, solid, straight IInd class HW chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed for door/window complete all as specified & directed.

S&F 100 mm size Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21 complete all as specified & directed.

S&F 150 mm Aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified & directed.

S&F 150 mm extruded aluminium alloy handles, fabricated type anodised complete all as specified & directed.

S&F GI wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with stainless steel wire staple/ wooden beads complete all as specified & directed.

Taking up or down steel tubing and connections, including cleaning for re-fixing of 15 mm dia complete all as specified & directed.

S&F tubes 15mm bore medium grade galvansied with all fittings, fixed to walls and ceilings or laid in floors complete all as specified & directed.

S&F in repair vitreous china WHB size 550x400 mm white flat back including pvc waste pipe but excluding taps, waste, chain & plug & porcelain stopper but including brackets with two coats of synthetic enamel painting over a coat of red oxide primer etc complete all as specified & directed.

S&F in repairs white vitreous china wash down water closet pan pedestal pattern (white) excluding fixing bolts, flushing cistern and flush pipe complete all as specified and as directed.

S&F in repair 10 Ltr capacity PVC valveless shyphonic action type low level flushing cistern white with inlet, ball valve, float valve and handle incl bracket and flush pipe of low level of 32mm dia fixed to wall complete all as specified & directed.

S&F in repair chromium plated health foucet with 8mm dia and 1.2 m long flexible tubes and wall hook suitable for EWC including nut/washer complete all as specified & directed.

S&F in repair PVC connection 15mm dia size and 450 mm long with 2 Nos check nuts its washers complete all as specified and as directed.

S&F cabinet mirror, box type of size 19" x 21" of colour as approved fixed to wall complete all as specified & directed.

S&F in repair bib tap 15 mm bore, chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrulecomplete all as specified & directed.

S&F in repair 15 mm bore pillar taps cast copper alloy with capstan heads chromium plated screwed down high pressure with or without lettered 'Hot' or 'Cold' with long screwed shanks & fly-nuts screwed for iron pipe & fixed complete all as specified & directed.

S&F in repair aluminium anodised tubular towel rail 20 mm dia D type 60 cm long between flanges complete all as specified & directed.

S&F in repair angle cock 15 mm bore fancy type chromium plated, with capstan head, high pressure, screwed down, screwed for iron pipe or for brass ferrule fixed to iron pipe complete all as specified & directed.

S&F in repair CP two way angle valve with wall flanges 15 mm bore, screwed down, screwed for iron pipe or for brass ferrule complete all as specified & directed.

S&F in repair of stainless steel soap dish, of standard size and shape complete all as specified & directed.

S&F PVC (SWR) pipes 110mm bore single socketed in any length with rubber ring joints laid in fixed to wall, trenches complete all as specified & directed.

M/L PVC(SWR) bend of 110mm dia of any radius etc complete all as specified and directed

S&F PVC (SWR) nahani/ floor trap, plain with grating with or without waste hole including jointing with solvent cement 75mm dia etc complete all as specified & directed.

M&L for preparation of new wooden surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint (Ordinary tint) over a coat of primer complete all as specified & directed.

M & L for preparation of new steel surfaces any description over 10 cm width or girth and applying two coat of synthetic enamel paint over a coat of red-oxide primer complete all as specified & directed.

M&L Preparing old wooden surfaces exceeding 10Cm in width or girth and applying two coats of synthetic enamel paint over a coat of primer complete all as specified & directed.

M&L Preparing old steel surfaces exceeding 10Cm in width or girth and applying two coats of synthetic enamel paint over a coat of primer complete all as specified & directed.

M&L for applying 2mm thick wall care Putty in two layers on old surfaces including complete removal of existing wall finish of any type with wire brush, brooming, dusting and finally washing with water to clean the surface absolutely free from any kind of foreign materials and making good minor cracks etc. and surfaces absolutely even and smooth, rubbing with sand paper complete all as specified & directed.

M&L for applying two coats of oil bound distemper on wall or concrete over a coat of primer on prepared surfaces including, rubbing with sand paper complete all as specified & directed.

M&L preparation of new plastered or unplastered surfaces of wall and applying two coats of cement based paint over a coat of primer complete all as specified and directed.

Dismantling of Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified & directed.

Galvanised corrugated mild steel sheet with two corrugation site lab, fixed with coach schrew and washers,in roofs, walls etc with grade of zinc coating 275 complete all as specified & directed.

M&L for suspended false ceilling comprising of 6mm thick non asbestos fibre cement bulding boards fixed or laid/inserted to GI frame work with screws over Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/ intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre. Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified

Taking down carefully surface aluminium point wiring with PVC casing-caping (light, fan, socket, bell or power) including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc and making good disturbed surfaces complete all as specified & directed.

M&L for point wiring with 1100 volts grade PVC insulated FR-LSH multistranded copper conductor cable 1.5 sqmm (Phase - Red, Neutral - Black) and earth continuity conductor 1.5 sqmm (Green) drawn into and including PVC casing-caping not less than 32x12 mm ISI marked ivory colour with all fittings / fixing accessories and sunken modular GI metal boxes not less than 1.2 mm thick and white modular mounting cover plates with frame for mounting of modular switches, sockets, fan regulators etc as required for One light point controlled by one switch.

All as per above item No 57 but one fan point controlled by one switch.

All as per above item No 57 but One socket outlet 6 amp controlled by one switch on the same board with other switches.

All as per above item No 57 but One socket outlet 6 amp controlled by one switch on indepdendent board.

M&L for point wiring with 1100 volts grade PVC insulated FR-LSH multistranded copper conductor cable 2.5 sqmm (Phase - Red, Neutral - Black) and earth continuity conductor 2.5 sqmm (Green) drawn into and including PVC casing-caping not less than 32x12 mm ISI marked ivory colour with all conduit fittings / fixing accessories and sunken modular GI metal boxes not less than 1.2 mm thick and white modular mounting plates with frame for mounting modular switches, sockets as required for 3 pin 16 amps socket outlet controlled by one switch.

S&F angle holder, insulated polycabonate body with back plate complete. Make - Havells Reo / Anchor Penta PC / SSK / CONA as approved complete all as specified & directed.

S&F modular switch one way 6 amp 1 module all as per Legrand Mylinc cat ref no. 675501 or equivalent in Schneider Zencelo or MK Blenze as approved complete all as specified & directed.

S&F modular switch one way 16 amp 1 module all as per Legrand Mylinc cat ref no. 675511 or equivalent in Schneider Zencelo or MK Blenze as approved complete all as specified & directed.

S&F modular socket 6/16 - 2/3 pin combined 2 module all as per Legrand Mylinc cat ref no. 675555 or equivalent in Schneider Zencelo or MK Blenze as approved complete all as specified & directed.

S&F modular socket 6 amp 2/3 pin combined 2 module all as per Legrand Mylinc cat ref no. 675552 or equivalent in Schneider Zencelo or MK Blenze as approved complete all as specified & directed.

S&F modular hum free electronic step fan regulator, 100 watt 2 module all as per Legrand cat ref no. 675530 or equivalent in Schneider Zencelo or MK Blenze as approved complete all as specified & directed.

S&F MCB distribution board SPN 08 ways powder coated, CRCA steel sheet constructed as per IS : 8623, degree of protection IP 43 - IK 09 with metal door, recess mounted, having insulated 100 amp tinned copper bus bar, neutral busbar, earth bar, din bar, detachable gland plate, interconnection, earthing connection, blanking plates in unused spaces complete all as specified & directed.

S&F MCB distribution board ETPN, 415 volts, 4 ways powder coated, CRCA steel sheet constructed as per IS : 8623, degree of protection IP 43 - IK 09 with metal door, recess mounted, having insulated 100 amp tinned copper bus bar, neutral busbar, earth bar, din bar, detachable gland plate, interconnection, earthing connection, blanking plates in unused spaces as required. complete all as specified & directed.

S&F ceiling rose 6 amp, 3 plates polycarbonate body complete all as specified & directed.

M&L for submain wiring alongwith earth continuity conductor with PVC insulated FR-LSH multistranded copper conductor cable (Phase - Red, Neutral - Black, Earth - Green) drawing into and including PVC casing-caping not less than 32x12 mm, ISI marked ivory colour along with accessories of following nominal sizes 2x4 sqmm + 1x4 sqmm earth wire complete all as specified & directed.

S&F Single pole and neutral elclosure with two pin and earth plug and socket complete with one single pole MCB 240 V 20 Amp complete all as specified & directed.

S&F LED batten (1.2 m) made of aluminium housing with a PC glossy difusser duly prewired connection having a nominal system lumen output of 2000 lumens at a minimum system efficacy of 105 lumens per watt and total power consumption not more than 20 watt including driver. It has a rated system life time of 40000 burning hours at L70 and should have a color temperature of 6500K, CRI>80, THD < 10% and PF > 0.95 complete all as specified & directed.

S&F energy efficient recessed/surface mounted LED luminaire 36 Watt suitable for 2'x2' grid ceiling with flat diffuser and lumen output of 3300 lumens having constant current electronic driver duly connected with 0.5 sqmm white colour PVC insulated & sheathed three core flexible multi stranded copper conductor cable in renewal of any type luminaire as required complete all as specified & directed.

S&F MCBs as per load requirement 'C' series of breaking capacity 10 KA, ISI marked including required wiring connections with copper lugs of suitable size provided in MCB DBs of Single pole 6 to 32 amp complete all as specified & directed.

All as per item No 75 but Single pole and neutral (SPN) 40 amp complete all as specified & directed.

All as per item No 75 but Four pole 63 amp complete all as specified & directed.

M&L earthing complete with galvanized steel earth plate electrode of size 600mm x 600mm x6.0mm thick buried directly under ground vertically to a depth not less than 2.25 meter below ground level with top edge of the plate at a depth not less than 1.5m below ground level connected to and including galvanized iron wire 4.0mm not exceeding 7.5meters for each earth without protection pipe, including test point by means of bolts, nuts, check nuts, and washers made out of GI all as shown on plate No 5 of SSR Part I to the extent applicable to this item including necessary making PCC pit of size 0.3 m x 0.3 m x 0.3 m (inner size) in mix 1:3:6 type C1 with RCC 1:2:4 type B-1, 40 mm thick cover reinforced with 6 mm dia MS bars 3 Nos both ways with lifting hook made out of 6 mm dia bar and testing on completion to achieve value complete all as specified & directed.

S&F LED 35 Watt streetlight made up of prressure die cast housing with prismatic polycarbonate diffuser and individual LED's with secondary optics and IP 65/66 protection complete with fixing arrangement and connection as directed as per Bajaj cat ref No. BCLST 20W LED I code 169829 or equivalent in Havells or GE Lighting as approved complete all as specified & directed.

S&F LED bulkhead fitting 9 watt IP 66 & IK 09 with pressure diecast aluminum housing & polycarbonate diffuser duly prewired for connection with flexible multi stranded copper conductor cable as required all as per Philips cat ref no. WT202W LED6S CW PSU S1 PC or equivalent in Wipro or C&S Elect as approved complete all as specified & directed.

Taking down MCB distribution boards with incoming and outgoing controls any make, any capacity after disconnecting complete all as specified & directed.

Taking down carefully aluminium submain wiring with PVC surface conduit and making good disturbed surfaces complete all as specified & directed.

SUBIR KUMAR ROY

GHASI RAM SAHU

MODI CORPORATION