ADDN/ALTN TO THE EXISTING OFFICERS MESS BAR WITH ASSOCIATED B/R AND E/M WORK SERVICES AT AF STN CHIMNEY HILLS

Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting hard/dense soil complete all as specified and directed.

Material & Labour for Sand as sand cushioning for laying interlocking tiles complete all as specified and directed.

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 M depth for foundation and getting out in hard and dense soil complete all as specified and directed..

Returning, filling in including spreading leveling watering and well ramming in layers not exceeding 25 cm (soil) complete all as specified and directed.

Removing excavation materials not exceeding 50 Metre and deposition where directed at a level not exceeding 1.5 M above the starting point (soil) complete all as specified and directed.

Material & Labour hard core of broken bricks gauge n. exc 63 mm, deposited spreaded and leveled in layer not exc 15 cm thick, watered and rammed to atrue surface, broken stone or boulder complete all as specified and directed.

Excavation in trenches not exc 1.5 m wide and not exc 1.5 min depth for laying of UG Pipe and getting out in hard dense soil all as specified and directed.

Material & Labour Cement concrete 1:4 :8 type D2 using (40 mm graded aggregate) as in filling, fdn, mass concrete and sub base of floors etc complete all as specified and directed.

Material & Labour Reinforced Cement Concrete M-25 (20mm graded stone aggregate) design mix in foundations including rafts, footings, foundation beams, plinth beams, copings , bases for columns etc basement slabs, under reamed piles and mass concrete complete all as specified and directed.

Material & Labour for Reinforced cement concrete (Design mix) M-25 (20mm graded aggregate) as in Columns, pillars, piers,posts and struts complete all as specified and directed.

Material & Labour for Reinforced cement concrete (Design mix) M-25 (20mm graded aggregate) as in beam, Tie beam complete all as specified and directed.

Material & Labour for Reinforced cement concrete (Design mix) M-25 (20mm graded aggregate) as in Chajja, shelves complete all as specified and directed.

Supply only Integral water proofing compound complete all as specified and directed.

Material & Labour precast cement concrete block masonary exc. 10 cm width with solid block C1 (1:3:6) (using 20 mm graded stone aggregate) and setting in cement mortar (1:4) complete all as specified and directed.

Material and Labour precast cement concrete block masonary exceeding 10 cm width with solid block C1 (1:3:6) (using 20 mm graded stone aggregate) and setting in cement mortar (1:4) (except cement concrete block) complete all as specified and directed. NOTE:- PCC Blocks obtained from dismantling shall be used in this work.

Material & Labour Plain cement concrete 1:3:6 type C-1(using 20mm graded stone aggregate) in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs not provided for, water troughs and the like including weathering, slightly rounded or chamfered angles and throating complete all as specified and directed.

Material & Labour for Damp proof course 40mm thick in cement concrete 1:2:4 Type B0 using 12.5mm graded stone aggregate horizontal sufaces including necessary formwork complete all as specified and as directed.

Form work for rough finished surfaces to side of concrete foundations, footings, bases of coloumns,raft and raft beams, sides and soffits (If any) of foundation and plinth beams and similar workcomplete all as specified and directed.

Formwork to sides of pillars, posts, struts, piers, columns and stanchions fair finished complete all as specified and directed .

Formwork to sides of Beams, lintels fair finished complete all as specified and directed.

Formwork to chulla hoods, chajjas, trough , shelve and similar works fair finished complete all as specified and directed .

Taking down chowkats or frames with shutters ( without taking of shutter from the frame) not exceeding 1.5 sqm each complete all as specified and directed.

Taking down chowkats or frames with shutters ( without taking of shutter from the frame) exceeding 1.5 sqm but n.exc 4.00 sqm each complete all as specified and directed.

Supply & Fixing of of 40mm thick Solid PVC Sandwich Panel for Partitions with 1mm Plain/printed PVC Sheet on both sides suitably fixed in M.S. angle frame work rate including frame work as per specification & drawing complete all as specified and directed.

Supply & Fixing of Ist class hard wood (Teak wood) Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered including segmental or carving work, put together with glue pinned at joints design and pattern all as directed by Engineer-in-Charge.

Supply & Fixing of 35mm thick Ist class hard wood (Teak wood) Glazed and skeleton shutters door, open rebated and prepared to receive glass, gauze, etc. divided into squares with plain, chamferred or rounded, mitred and rebated sash bars including moulding any numbers etc. sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a);fitted to wooden chowkats, design and pattern all as directed by Engineer-in-Charge.

Supply & Fixing of 30mm thick Ist class hard wood (Teak wood) Glazed and skeleton shutters window/ventilator, open rebated and prepared to receive glass, gauze, etc. divided into squares with plain, chamferred or rounded, mitred and rebated sash bars including moulding any numbers etc. sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (b);fitted to wooden chowkats, design and pattern all as directed.

Supply & Fixing for Aluminium Anodised door shutter with frame using aluminium section of size 63.50x38.10x1.95mm thick (single Groove) and shutter consisting bottom and middle rail using aluminium section of size 114.30x44.45x2.15 mm thick , top rail using aluminium section of size 83.50x44.45x2 mm thick ,vertical style using aluminium section of size 85x44.45x1.80 mm thick with 6mm thick black tinted glass insert to full shitter including aluminium andised handle of size 200mm long 02 nos ,150mm tower bolt - 01 no glazing clip size 19x17.30x1.20 m thick ,rubber ring/gasket/beading sliding /dead lock 6 lever size 100 mm, Airforce logo UV Print technology etc complete all as specified and directed.

S&F 125mm Butt hinges extruded brass, with mild steel hinge pin, bright polished and fixed, type B-12 complete all as specified and directed.

Supply & Fixing for Brass, sliding door bolt 300mm long with sand or die cast brass staple (bolt type) and fixing bolt with rolled or drawn brass bolts and fixed all as specified and directed.

Supply & Fixing for Brass extruded Double action spring hinges 125mm , with phosphor bronze wire spring, bright polished complete all as specified and directed.

Supply & Fixing for Brass extruded Double action spring hinges 75mm , with phosphor bronze wire spring, bright polished complete all as specified and directed.

Supply & Fixing for Brass, barrel tower bolts fancy type 200mm extruded including complete fixtures complete all as specified and directed.

Supply & Fixing for Brass, barrel tower bolts fancy type 100mm extruded including complete fixtures complete all as specifed and directed.

Supply & Fixing for Brass, handles fancy type 200mm extruded including complete fixtures design,shape and pattern complete all as specifed and directed.

Supply & Fixing for Brass, handles fancy type 125mm extruded including complete fixtures design,shape and pattern complete all as specifed and directed.

Supply & Fixing for WPC cupboard shutter/ patitions of thickness 18 mm ( ±0.25) consisting of desired size fixed to WPC frame work as in shutters and shelves of cabinets, cupboards fixed in repairs complete all as specifed and directed.

Supply & Fixing for 75mm dia auto concealed hydraulic stainless steel spider/butterfly hinges suitable for cupboards complete all as specifed and directed.

Supply & Fixing for floor door stopper of Brass body and tongue with hard drawn steel spring 150mm , design and pattern all complete all as specifed and directed.

Material & Labour for TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia for securing with clips quality conforming to deformed or twisted bars complete all as specified and directed.

Material & Labour for TMT bars 6 to 8 mm dia as in stirrups / spacers, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia for securing with clips quality conforming to deformed or twisted bars complete all as specified and directed.

Supply & Fixing for steel work in Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, MS Tubes, channel or flat sections) including distance pieces, cleats etc.or induction butt welded to angles, cleats conforming to I. S.1161-1979 grade St.-240 complete all as specified and directed.

Supply & Fixing of Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick (Tile pattern or designer pattern as approved) of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified.

Supply & Fixing of Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

Material & Labour for 10mm thick plaster of paris ceiling (Gypsum anhydrous) to flat surface over, 600X600 mm in size, staples on GI grid in ceiling snap grid frame work and hangers 6 mm dia GI (up to 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of GI flat 40x3 mm size 60mm long with complete hanging arrangements finished with two coats of oil bound distemper over putty finished etc complete all as specfied and directed . Note :- Design, pattern and colour of ceiling work has to be approved by AGE(I) complete all as specified and directed.

Supply & Fixing of Bonded mineral wool or ( fiber glass wool) blanket slab made from glass density 24 Kg/Cum and fixed to wall panel as per manufacturer's instructions, 40 mm in thickness complete all as specified and directed by Engineer in charge.

Material & Labour for provinding 75mm thick cement concrete 1:3:6 type C1, (using 20mm graded stone aggregate) finishing cement concrete surface even and fair without using extra cement as in plinth protection complete all as specified and directed.

Material & Labour PCC 1:4:8 type D-2 (using 40 mm graded stone aggregate) 100mm thick as in sub base complete all as specified and directed.

Material & Labour for PCC 1:2:4 type B-0 (using 12.5mm graded stone aggregate) of 25mm thick as in levelling course, finished surfces even and rough to receive floor finish complete all as specified and directed.

Material & Labour for 18-20mm thick Granite (on any type) work (table rubbed and polished) in steps, jambs pillars, window cills, cooking platforms, vertical surfaces and like in over and including 20mm thick cement screed in Cement Mortor 1:4 including pointing in white or coloured cement (1:2) using marble dust with admixture of pigment to match with shade of granite incl polishing complete all as specified and directed.

Material & Labour Vitrified Ceramic coloured dark shade/double charged/ultracharged tiles 10 mm thick (square/ rectangular) polished, area of each tiles exc 0.42 Sqm but not exc 1.00 sqm, in floors etc. over 20mm screed bed in CM 1:4 set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

Material & Labour for Machine pressed precast concrete interlocking paver block polished rubber moulded any shape, size & colour confirming to IS 15658-2006 of 80mm thickness, M-40 Grade with grey cement and pigment complete all as specified and directed. Note:- Sand cushioning will be measured and paid seperately.

Taking down cement plaster on brick work or stone walls etc incl raking out joints hacking for key scrubbng down with water complete all as directed.

Material & Labour for rendering 15 mm thick on fair faces of brick work or concrete surfaces with Cement Mortor 1:6 finished even and smooth without using extra cement in internal surfaces complete all as specified and directed.

Material & Labour for 15mm thick rendering in Cement Mortor 1:4 on brick or concrete surfaces finished even and smooth complete all as specified and as directed.

Material & Labour for preparing new plastered surface and apply two coat of oil bound distemper over a coat of wall care putty to obtain smoothness of wall surfaces over one coat of primer complete all as specified and directed.

Material & Labour preparation and washing, rubbing down and stopping of distempered and painted surfaces of wall including cornices and applying two coat of acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, over a coat of wall care putty to obtain smoothness of wall surfaces of approved manufacturer, of required shade and colour complete as per manufacturer's specification complete all as specified and directed.

Supply & Fixing of Sheet glass 5.5mm thick, tinted/ordinary quality (one way) and glazing with oil putty or rubber gasket or nails in square n.exc 0.5 Sqm size in each pane all as specified and directed. Note : Glass colour as approved by AGE(I).

Material & Labour preparation steel surfaces with two coats of Synthetic enamel paint over one coat of red oxide primer complete all as specified and directed.

Material & Labour Melamine /French polishing on wooden surfaces of any description, width or girth including cleaning and preparing the surface including a coat of wood filler on new works with two or more coats all as specified and directed. Note : Colour and shade of polish approved by AGE(I).

Supply & Fixing for sinks without drainage board made of stainless steel 1mm thick kitchen with Steel waste coupling 40mm with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified and directed.

Supply & Fixing for Brass chromium plated bottle traps 40mm for sinks/wash basin with inlet and outlet screwed for pipe or connections including necessary packing, union and cap all as complete fixing arrangement as specified and directed.

Supply & Fixing for of 20mm dia CPVC pipes SDR 11 & Plain CPVC SDR 11 including complete fittings on walls/ceiling or laying in floors complete all as specified and directed.

Supply & Fixing for 15mm CP fancy type angle cock concealed type screwed for iron pipe or for brass ferrules complete all as specified and directed.

Supply & Fixing for 15mm bore fancy type pillar/pull down sprayer with extendable CP pipes suitable for moving of taps, hot or cold with long screwed shanks and flynuts screwed for iron pipe complete all as specified and directed.

Supply & Fixing for PVC connection 15mm dia and 450mm long complete all as specified and directed.

Supply & Fixing for PVC (SWR) pipes 110mm single socketed in any length with rubber ring joints fixed to floor/trenches complete all as specified and directed.

Supply & Fixing for PVC (SWR) pipes 75mm single socketed in any length with rubber ring joints fixed to floor/trenches complete all as specified and directed.

Supply & Fixing in repair for PVC (SWR) 110mm junction single, bends complete all as specified and directed.

Supply & Fixing in repair for PVC (SWR) 75mm junction single, bends complete all as specified and directed.

Supply and lay Galvanised iron pipes 25 mm dia medium grade ISI marked with all required necessary fittings complete laid in trenches/ ,fixed on wall by brackets including route indicators all as specified and as directed.

Supply & Fixing 25 mm dia Gun-metal, globe gate valves,with iron wheel head, screwed both ends for iron pipe all as specified and direcetd.

Supply and lay LT under ground cable XLPE insulated armoured 1100V grade with multistranded aluminium conductor confirming to relevant IS in trenches, ducts, through pipes fixed to wall etc all as directed including cable gland, terminal socket and connecting up of size 50 sqmm 3.5 core including dismantling of old U/S cable.

Material & Labour for for reinforced precast concrete cable cover, class ELV, type 1 with peak, size 250mm x 150mm x 40mm® flat perpendicular to axis of cable for protecting complete all as specified and directed .

Supply and Spread Natural Riddled soil in trenches for cushioning and covering to cable complete all as specified and directed. Note :- Only Punned thickness will be considered for paayment

Material & Labour for cutting road / hard standing/Plith Protection to depth not exceeding 60 CM and to width not exceeding 45 CM for laying HDPE Pipes and making good the disturbed surfaces by 1:3:6 type C1 using 20 mm graded stone aggregate complete all as specified and as directed .

S&F Galvanised Iron tubing light grade, 50mm dia in trenches for road crossing/laid in floors etc

Supply and install in repair MCCB, 4 pole, 415 v, adjustable type, 63 Amp, 50 HZ, 36 KA including spreader links on both sides complete all as specified and directed.Note:-(Making necessary connection with the existing panel.

Material & Labour for earthing complete with galvanized steel earth plate electrode 60cmx60cmx6mm thick buried directly in ground earth pit not less than 2.25m below ground level with top edge of earth plate not less than 1.5m below normal ground level, connected to galvanized iron strip 32x6mm as a earthing lead by means of bolts, nuts, checks nuts, washers etc made of galvanized of steel, earth strip including and protected by galvanized iron pipe(light grade) 40 mm dia from plate to Panel Board, galvanized iron pipe light grade 20mm dia bore and funnel watering including test point necessary excavation ,earth work, concrete pit M-10, CI cover, frame and funnel,Charchol dust,Salt all as specified in plate No 3 of SSR-1991(part-1) complete all as specified and as directed.

Supply and fixing TPN distribution boards,Vertical type, protection class IP-43, Double door,4 Way, suitable for mounting MCCB Amps as incomer and MCB SP,TP as outgoing with min 160 Amps rating bus bar ,concealed in wall all as specified and directed by engineer in charge .

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc complete as specified and directed.

M & L for Point wiring with 1.5 sqmm single core PVC insulated FRLS cable 1100 volts grade with copper conductor drawn in and incl with multi stranded copper conductor drawn through and including suitable size Non metalic regid PVC conduit and all conduit accessories (concealed) and including provision of 1.5 sqmm PVC insulated copper cable FRLS as earth continuity conductor fabricated branded PVC Surface Box /Metal Concealed box of size 1.2 mm thickness concealed in walls with suitable Plastic/Sunmika outer cover with suitable screws for housing switches socket outlets fan regulators etc for one light point controlled by one , one way switch complete all as specified and directed

M & L for Point wiring with 1.5 sqmm single core PVC insulated FRLS cable 1100 volts grade with copper conductor drawn in and incl with multi stranded copper conductor drawn through and including suitable size Non metalic regid PVC conduit and all conduit accessories (concealed) and including provision of 1.5 sqmm PVC insulated copper cable FRLS as earth continuity conductor fabricated branded PVC Surface Box /Metal Concealed box of size 1.2 mm thickness concealed in walls with suitable Plastic/Sunmika outer cover with suitable screws for housing switches socket outlets fan regulators etc for one three point socket outlet 5 Amp controlled by one , one way switch on independent board complete all as specified and directed

M & L for Point wiring with 1.5 sqmm single core PVC insulated FRLS cable 1100 volts grade with copper conductor drawn in and incl with multi stranded copper conductor drawn through and including suitable size Non metalic regid PVC conduit and all conduit accessories (concealed) and including provision of 1.5 sqmm PVC insulated copper cable FRLS as earth continuity conductor fabricated branded PVC Surface Box /Metal Concealed box of size 1.2 mm thickness concealed in walls with suitable Plastic/Sunmika outer cover with suitable screws for housing switches socket outlets fan regulators etc for one three point socket outlet 5 Amp controlled by one , one way switch on same board complete all as specified and directed

M & L for Point wiring with 2.5 sqmm single core PVC insulated FRLS cable 1100 volts grade with copper conductor drawn in and including with multi stranded copper conductor drawn through and including suitable size Non metalic regid PVC conduit and all conduit accessories (surface) and including provision of 2.5 sqmm PVC insulated copper cable FRLS as earth continuity conductor fabricated branded Modular Metal concealed in walls with incl suitable sunken type pressed steel terminal box and suitable laminated sheet top cover for One 3 pin socket outlet, 15 Amps on independent board, complete all as specified and directed.

Supply & Fixing in repair switch piano 6 Amps one way flush type complete all as specified and directed

Supply & Fixing in repair switch piano 16 Amps one way flush type complete all as specified and directed

Supply & Fixing in repair socket, 2 in 1, 3 pin 5 Amps flush type complete all as specified and directedcomplete all as specified and directed

Supply & Fixing in repair socket 2 in l, 3 pin 6 Amps and 3 pin 16 Amps flush type complete all as specified and directed

Supply & Fixing of Lamp holder,Angle and batten type, PVC/Polycarbonate type with cord grip cap suitable for pendant fittings all as specified and directed .

Supply & Fixing of LED Bulb ,B22 Type ,09 W lumens 105 /watt,6500 K Temperature all as specified and directed .

Supply & Fixing of LED luminaire 600 mm x 600 mm,20/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as per directed .

Supply & Fixing of hanging décor lights Edision E 27 rustic lamp of 40 W brown type, Complete hanging arrangement with pendent holder and fixing accessories all as per directed.

Supply & Fixing of LED warm strip light light 6 watt 220 volts AC 50Hz fixing on the ceiling properly good finishing with the existing ceiling and necessary connection with the wiring complete all as per directed.

Supply & Fixing of Wall mounting fan 400 mm sweep,with regulator 240 V,50Hz, 5 Star rating energy saving Superior air delivery white colour all as secified and as directed .Note: Manufacturer warranty Minimum 2 years from the date of Installation

Supply & Fixing of MCB SP 6 to 32 Amps10 KA 240V 50HZ, ISI Marked.

Supply & Fixing of MCB SPN 6 to 32 Amps10 KA 240V 50HZ, ISI Marked.

Supply & Fixing in repair ceiling rose 3 terminals ,ISI Marked all as specified and directed .

Supply & Fixing of RCCB, DP, 40 Amps AC type in accordance with IS:12640-1 and IEC-6100-1, suitable for 240 Volts, 50 Hz with 10 KA short circuit withstand capacity.

Supply & Fixing in repair MCB distribution board SPN 8 way single door 240V powder coated with 200 Amps rated bus bar neutral link etc.

Material & Labour in replacement submain wiring /Circuit wiring with PVC insulated, single core, multi stranded, 1100 volts grade unsheathed copper conductor cable in and including PVC Conduit/Casing capping with accessories fixed on wall /ceiling with GI screws complete with 2x4 Sqmm +1x 4 Sqmm for earth continuity conductor all as directed. Note :- 2 runs of 4 sqmm, 1 run of 4 sqmm (Earth Cotinuity conductor) and 1 run of PVC conduit/casing and capping shall be measured as one unit length

Material & Labour in replacement submain wiring /Circuit wiring with PVC insulated, single core, multi stranded, 1100 volts grade unsheathed copper conductor cable in and including PVC Conduit/Casing capping with accessories fixed on wall /ceiling with GI screws complete with 4x6 Sqmm +1x 6 Sqmm for earth continuity conductor all as directed. Note :- 2 runs of 6 sqmm, 1 run of 6 sqmm (Earth Cotinuity conductor) and 1 run of PVC conduit shall be measured as one unit length

Supply & Fixing of 35/36 watts LED Security light fitting with pressure die cast IP 65 protection, luminous efficiency of 100 lm/watt, PF > 0.95, CRI > 80, colour temprature 5700 K suitable for primary roads with all connected accessories including bracket made out of GI tubing of 40 mm light grade outer dia, 1.2m length,with GI clamps, nuts and bolts etc for fixing of fitting complete all as specified.

Material & Labour for Drilling and Tapping cast iron water mains 50 mm bore (in position) and reduceing the bore size for branch connection of internal dia 50 mm including all fittings such as bend,elbows,tees,reducers and unions etc all as directed by engineer in charge.

Demolition of stone/boulder , brick/PCC block masonry work built in cement mortar complete all as specified and as directed.

Demolition of reinforced cement concrete in ground floor and paving (reinforcement cut as required to facilitate demoliton) complete all as specified and directed.

Demolition of unreinforced cement concrete in ground floor and paving not exceeding 15cm thick (below or above ground level) etc complete all as specified and directed.