Construction of Toilet complex in Civil Court Campus at Begusarai, Dist- Begusarai.

Material Statement of Toilet Complex

S.I Item Qty Sand (M³) Bricks No. Chips (M³) L/sand M³ Cement

12 Inspection chamber 5 no 1.00 705 0.5 7

BCD BEGUSARAI BCD BEGUSARAI BCD BEGUSARAI

BILL OF QUANTITY

BUILDING DIVISION BEGUSARAI.

Name of Work : Construction of Toilet complex in Civil Court Campus at Begusarai, Dist- Begusarai.

Estimated Cost :- 1585801.00 BOQ issued to:-

Earnest Money :- 31800.00 Address :-

Cost of B.O.Q :- 5000.00 Reg. No :-

Time of Completion:- 01 Month

Sl. No. SR Item No. Item of Works Quantity Unit Rate Amount (Rs.)

1 20.3A.1 Making 25 cm (10") dia bore up to 4 mtr depth below ground with hand auger of approved quality in ordinary soi! (vide classification of soil item A ) true to plumb and without eccentri city in any stage of operation and disposal of the excavated earth up to 50 mtr , Lead in eluding all lifts , all complete as per approved disign and direction of E/l Details of cost for 4 piles of 4 m= 16 mtr )

2 2.8.1 Earth work in excavation in foundation trenches or drains(not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m . including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50m

3 2.28 Supplying and Filling in plinth with local sand and under floors including, watering, ramming consolidating and dressing complete

4 11.72 Providing designation 100 A one brick flat soling joints filled with local sand including cost of watering, taxes, royalty all complete as per building specification and direction of E/l

5 4.1.3 Providing and laying in position cement concrete of specified grade exluding the cost of centring and shuttering-all work upto plinth level.1:2:4(1 Cement :2 coarse sand:4 graded stone aggregate 20 mm nominal size)

6 5.1.2 Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centring,shuttering,finishing and reinforcement-All work puto plinth level 1:1:5:3(1 cement: 1.5 coarse sand:3 graded stone aggregate 20 mm nominal size)

7 5.2.2 Reinforced cement concrete work in wall (any thickness), including attached plasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts, etc. upt floor five level excluding cost of centring, shuttering, finishin and reinforcement.1:1:5:3(1 cement: 1.5 coarse sand:3 graded stone aggregate 20mm nominal size)

8 6.1.12C Brick work with fly ash bricks as per IS 12894(2002) & IS 3495 in foundations and plinth in : Cement mortar 1.:4 (1 cement: 4 coarse sand )

9 6.1.14C+6.3C Brick work with fly ash bricks as per IS 12894(2002) & IS 3495 in foundations and plinth in : Cement mortar 1:6 (1 cement: 6 coarse sand ) Extra tor Brick work in superstructure above plinth level upto floor V cum

10 6.1.12/1 Brick work with bricks of class designation 100A in foundations and plinth in : Cement mortar 1:6 (1 cement: 6 coarse sand )

Septic Tank 6.60 CUM 5017.90 33118.00

11 6.18 A Half Brick massonary with brick of class designation 100A in Cement mortar 1:4 (1 cement: 4 coarse sand )

Septic Tank 6.00 CUM 599.30 3596.00

12 5.9 Centring and shuttering including strutting,propping etc. and removal of form for.

5.9.1 Suspended floors, Roofs (S.Tank Cover Slab)

5.9.6 Columns,Pillars, Piers, Abutments, Posts and Struts

5.9.5 Lintels, beams, plinth bams, griders, bressumers and contilevers

5.9.3 Suspended floors, roots, landings, balcnies and access platform

5.9.19 Weather shade,Chajjas, corbels etc. including edges

13 13.13.2+13.36.6 20 mm thick cement plaster of mix:1:4 (1 cement:4 coarse sand) with water proofing compound

14 5.22 Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete.

5.22.7A Thermo-Mechanically Treated bars TMTC-500-8mm dia. 566.55 kg 94.50 53539.00

5.22.7B Thermo-Mechanically Treated bars TMTC-500-10mm dia. 497.83 kg 92.60 46099.00

5.22.7C Thermo-Mechanically Treated bars TMTC-500-12mm dia. 796.00 kg 90.80 72277.00

15 13.11.4 Cement plaster in course sand 12 mm cement plaster of mix:1:6 (1 cement:6 coarse sand)

16 13.17.1 12 mm cement plaster 1:3 (1 cement: 3 coarse sand) finished with neat cement Punning

17 13.24.2 6 mm cement plaster to ceiling of mix :1:4(1 cement: 4 coarse sand)

18 13.80.A.2 Providing and applying white cement based putty of average thickness 2 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

19 13.46A.1 Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade :New work (Two or more coat applied @ 1.43 ltr/ 10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm)

20 11.39 Providing and laying Ceramic glazed floor tiles 300x300 mm (thickness to be specified by the manufacturer) of 1 st quality conforming to IS : 13755 of NITCO , ORIENT , SOMANY , KAJARIA or equivalent make in colours such as white , Ivory , Grey , Fume , Red , Brown , laid on 20 mm thick cement motar 1:4 (1 cement: 4 Coarse sand) including grouting the joints with white cement and matching pigments etc, complete.

21 11.36 Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS : 15622 (Thickness to be specified by the manufacture) of approved make in all colours, shades except burgundy , bottle green , black of any size as approved by Engineer-in-charge in skirting , risers of steps and dados over 12 mm thick bed of cement Motar 1:3(1 cement: 3 coarse sand ) and jointing with grey cement slurry @ 3.3 kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

22 11.19.1 chequered terrazo tiles 22 mm thick with marble chips of sozes upto 6 mm in floors jointed with neat cement slurry mixed with pigement to match the shade of the tiles, including rubbing and polshing complete on 20 nm thick bed of cement mortar 1:4 (1 cement:4 coarse sand)

23 8.2.2.1 providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size,approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups,including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.

24 9.48.1 Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.Fixed to steel windows by welding

25 9.1.2 Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately).

26 9.20.1 Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type,core of block board construction with frame of 1 st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:

27 21.1.1.1 Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / aneling,C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :

28 26A.7 Providing, fabricating and supplying and fixing panels of aluminium composite panel cladding in pan shape in metalic colour of approved shades made out of 4mm thick aluminium composite panel material consisting of 3mm thick FR grade mineral core sandwiched between two Aluminium sheets (each 0.5mm thick). The aluminium composite panel cladding sheet shall be coil coated, with Kynar 500 based PVDF / Lumiflon based fluoropolymer resin coating of approved colour and shade on face # 1 and polymer (Service) coating on face # 2 as specified using stainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backer rods etc.

29 21.3.2 providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):

30 13.94.1 Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade:Two or more coats on new work over an under coat of suitable shade with ordinary pain+ of approved brand and manufacture

31 10.36 Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes,channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, ( for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts,fasteners etc.).

32 17.1.1 Providing and fixing water closet squatting pan (Indian type W.C.pan ) with 100 mm sand cast Iron P or S trap, 10 litre low fixtures complete, including cutting and making good the walls andlevel white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and floors wherever required :

33 17.3.1 Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I.brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required :

34 17.7.A Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require :

35 17.4.1 Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required :

36 18.49 Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 :

37 18.52 Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931.

38 17.34.1 Providing and fixing mirror of superior glass of superior quality

39 17.72 Providing and fixing PTMT Towel Ring of superior quality

40 17.34.1 Providing and fixing Toilrt paper holder of superior quality

41 18.9 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement ,trenching ,refilling & testing of joints complete as per direction of Engineer in Charge.

18.9.2 20 mm nominal outer dia Pipes 15.00 M 205.30 3080.00

18.9.3 25 mm nominal outer dia Pipes 35.00 M 294.70 10315.00

18.9.4 32 mm nominal outer dia Pipes 25.00 M 359.10 8978.00

42 18.48 Providing and placing on terrace (at all floor levels) polyethylene water storage tank, ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

43 12.78 Providing and fixing wall face Upvc rain water pipe

12.78.2 110 mm nominal outer dia Pipes 25.00 M 257.50 6438.00

12.78.1 75 mm nominal outer dia Pipes 25.00 M 162.70 4068.00

44 12.79 Providing and fixing wall face Upvc molded fitting/accessosies for upvc rain water pipe

12.79.1.2 110 mm nominal outer dia coupler 2.00 M 120.00 240.00

12.79.1.1 75 mm nominal outer dia coupler 3.00 M 79.80 239.00

12.79.5.2 110 mm nominal outer dia bend 4.00 M 132.00 528.00

12.79.5.1 75 mm nominal outer dia bend 5.00 M 91.80 459.00

12.79.4.2 110 mm nominal outer dia bend 2.00 M 190.70 381.00

12.79.4.1 75 mm nominal outer dia bend 3.00 M 124.20 373.00

45 18.37 Constructing masonry Chamber 60x45x50 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) 5 Nos 6849.90 34250.00

46 19.32.1 Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. 1 Nos 33603.40 33603.00

47 0L01 Supplying Un-Skiled labour Site cleaning 9 Nos 355.42 3199.00

48 24.1.1.1 Boring/drilling bore well of required dia for casing/strainer pipe by suitable method 300mm dia etc all complete job as per building specification & direction of E/I.

49 24.3 Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths,as per direction of Engineer -in-charge.

50 24.4.1 Supplying assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipe of required 100mm dia etc all complete job as per building specification & direction of E/I.

51 24.13.1 Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell

52 24.14.2 Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete

53 24.15 Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS:2800 (part I).

54 24.8 Gravel packing in tubewell construction in accordance with IS:4097 including providing gravel line/medium/coarse in required grading and sizes etc all complete job as per building specification & direction of E/I.

55 24.12 Development of tubewell in accordance with IS:2800 (Part_1) and IS:1189 to establism maximum rate of usable water yield without sand content (beyond permissible limit) with required capacity air compressor running the compressor for required time etc all complete job as per building specification & direction of E/I.

56 NS Supplying 1 H.P. submersible motar of approved mark & ISI mark automatic starter with all accossories for running condition etc all complete job as per building specification & direction of E/I.

57 18.9.50 Providing and fixing chlorinated Polyvinyl Chloride (CPVC) pipes havaing thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings this inludes jointing of pipe & fitting etc all complete job as per building specification & direction of E/I.

58 Carriage of materials

59 Extra cost of materials

(a) Cement 341 bags 5.50 1876.00

CORRECTION FACTOR @.982 ON SOR& DSR (ON S.NO.135) = ₹ 1,505,126.00

Executive Engineer

B.C.D, BEGUSARAI