REPAIR AND REHABILITATION TO RCC MEMBER BEAMS COLUMNS SLABS CHAJJA PARAPAT ETC INCLUDING ROOF SUNKEN WATERPROOFING TREATMENT IN THE AOR OF AGE B R I UNDER GE HISAR

Amount

M&L for treatment of sunken floor slab comprising of the following specifications with and including demolition of sunken floors complete all as specified and directed :- (i) Cleaning the sunken/lowered portion of RCC slab surface (including vertical total depth plus skirting height) of floors by wire brush, chisel out any mortar sticking to the surface and brooming completely. Provision of 40mm thick avg PCC 1:2:4 type B-0 using 12.5mm graded aggregate as in padding concrete to achieve proper slope including cutting holes in bricks or RCC wall for spout. (ii) Rendering of uneven surfaces with 6mm thick CM 1:4 mixed with and including integral water proofing compound Sika Plastocreat plus or equivalent make in Fosroc / Thremax as approved by GE @ 0.2% by wt of cement consumed including filling it with water to check dampness and seepage and where dampness / seepage is noticed, nozzles shall be fixed and grouting carried out. (iii) All junctions points of side wall where CI/GI/PVC pipes are passing through shall be sealed with epoxy putty Sikaguard 694 F(I) or equivalent make in Fosroc / Thremax as approved by GE. (iv) After drying putty, wash the slab and sides of sunken portion with water and make it clear and clean. (v) Applying two coats of polymer modified cementious water proof coating with Sika Topseal 107 or or equivalent make in Fosroc / Thremax as approved by GE in two coats @ 3kg/sqm to sanwiched with glass fibre reinforcemnt: Sika Fab-1 or or equivalent make in Fosroc / Thremax as approved by GE over base coat as per mnaufacturer's instruction to bottom and vertical sides up to finished floor level+100mm height. The thickness of two layer shall be 1mm. When the second layer is still sticky, coarse sand spray shall be carried for the vertical and bottom surface of the sunken portion. (vi) Plaster the bottom and sides up to bottom of the skirting with minimum 20mm thick CM 1:4 mixed with integral water proofing compound SIKA plastocreat plus or equivalent make in Fosroc / Thremax as approved by GE @ 0.2% by wt of cement consumed as per manufacturer's specification including rounding of corners and injuctions sloping towards spout.(vii) All pipes laid in sunken portion shall be covered with 50mm thick PCC 1:3:6 all round after painting with anticorrosive paint. (viii) The sunken floor shall be filled with lean concrete 1:7:12. Note :- (i) Test the water proofed area (ponding test) by filling water for at least 72 hours and tested for leakage seepage and to the entire satisfaction of GE. Test record for each sunken slab shall be maintained. The treatment shall be carried out by authorised applicators of chemicals. Cost of testing and all M&L is included in the rates quoted above. (ii) For payment purpose, the plan area of sunken floor shall be measured.

Chipping of loose/ damaged /cracked / previously repaired / delaminated or weak concrete by chieseling to expose the sound core concrete where ever required and to expose rusted reinforcement upto depth n.exc 50mm and disposal of rubbish off the premises to a distance not exc 50 mtrs including cleaning of reinforced concrete surface by air compressor complete all as specified and directed.

Supply and apply of rust remover cum passivator to remove rust from existing reinforcement by using product: Rustoff-100 of Sika or equivalent make in Fosroc/ Thermax as approved by GE, with density 1.01 Kg/ltr at 30 degree celsius and consumption : 0.2 Kg/Sqm/coat complete all as specified and directed. Note : The mtrl to be applied thoroughly on exposed rebars only with the help of a brush of suitable size. The area will be measured as length of bar x two times the dia of bar.

Supply and apply a cement based polymer modified rebar corrosion protection system to existing reinforcement using cement based polymer modified rebar corrosion protection system with consumption : 3.75 kg/Sqm for two coats and Product requirements: carbonation resistance: 2 mm of SikaTop Armatec®-108 of Sika or equivalent make in Fosroc / Thermax as approved by GE corresponds to 20 mm of normal mortar; bond strength > 1N / Sqmm according to ASTM C 882-78 complete all as specified and directed. Note: The mtrl to be applied thoroughly on exposed rebars only with the help of a brush of suitable size. The area will be measured as length of bar x two times the dia of bar.

M&L for Providing, mixing & applying two component Epoxy resin concrete Bonding coat on prepared RCC surfaces as per manufacturer's specification including prepartaion of surface throughly and cleaning complete where ever required with using Product: Sikadur®-32 LP of Sika or equivalent in Fosroc / Thermax as approved by GE with Consumption: 0.4 kg/Sqm and Product requirements: Complies with ASTM C 881-78, Type II Grade 2 Class B+C complete all as specified and directed.

M&L for providing by mixing and trowel application of prepacked, light weight, two component structural grade polymer modified fibre reinforced thixotropic cement mortar Sika Monotop 122F of Sika or equivalent make in Fosroc / Thermax as approved by GE at an average thickness exceeding 10mm and upto 25mm to the prepared concrete surface in soffit of slabs, beam, columns, parapets, fins and facias at any height, including finishing of applied Polymer mortar as per the technical specifications and manufacturer's instructions complete all as specified and directed .

M&L for weld-mesh of size 75mmx75mmx3mm to be wrapped on the exposed surface of rib of beam & on the slab bottom and tack welding to the exposed reinforcement at close intervals and gunite with cement mortar 1:3 mixed with admixture Sika Plasto creat plus or equivalent make in Fosroc / Thermax as per manufacturer's instructions as approved by GE around rib of beam or roof slab of thickness n.exc 40mm to be applied under an operating pressure. The gunited surface to be cured properly for a min of 7 days all in complete as per the technical specifications and manufacturer's instructions all as specified and directed.

Providing and fixing water tight centering & shuttering and Scaffolding including bolting, strutting, propping etc. including removal of form work from column, beam , slab etc. complete as per site requirement and directions of Engineer-in-charge.

Supply and apply a ready to use non shrink, cementitious free flow micro-concrete (<100 mm) using Product: SikaRep® Microcrete-4 + adequate coarse aggregate, Yield: approx 17 Ltr/bag (30 Kg) (depending on the size and quantity of coarse aggregate added), Product : SikaRep® Microcrete-4 or equivalent make in Fosroc / Thermax as approved by GE, Product requirements: compressive strength > 60 N/Sqmm (28 days) according to ASTM C 1107-99 complete all as specified and directed.

M&L for providing and fixing 12-16mm dia injection ports non returnable nozzle by drilling, cleaning and sealing holes 50-75 mm deep at 200mm c/c with fast setting high strength Epoxy putty, solvent free, three component compound based on epoxy resins, graded fillers and thixotropic agents using Sikadur 31 of Sika or equivalent make in Fosroc / Thermax as approved by GE as in beams, columns, slab and parapets as per the technical specifications and manufacturer's instructions complete all as specified and directed.

M&L for grouting of nozzles with low viscous moisture insensitive, High strength, epoxy resin grout with Sikadur 52 LP (IN) of Sika or equivalent make in Fosroc / Thermax as approved by GE with pressure not excedding 2-3 Kgf/Sqcm till the nozzle refuses to take further grout including cutting extra length of the nozzle after the grout hardens and finishes as per the technical specifications and manufacturer's instructions complete all as specified and directed.

M&L for providing by mixing and trowel application of prepacked, light weight, two component structural grade polymer modified fibre reinforced thixotropic cement mortar Sika Monotop 122F of Sika or equivalent make in Fosroc/Thermax as approved by GE at an average thickness of upto 10mm to the prepared concrete substrate in slffit of slabs, beam, columns, parapets, fins and facias at any height including finishing of applied Polymer mortar as per the technical specifications and manufacturer’s instructions complete all as specified and directed.

M&L for providing, fixing shear connector of 16 mm dia TOR steel spot 160 mm length with Sika anchorfix @-2+ Tropical or equivalent make in Fosroc/ Thermax as approved by GE, epoxy resin to RCC member including power drilling, cleaning of holes, insertion of epoxy, placing shear connector in position to ensure the bond as per manufacturer’s instructions complete all as specified and directed.

M&L for cutting V groove (15mmx10mm) along the crack line and cleaning the same with high pressure water jet and sealing with fast setting high strength Epoxy putty, solvent free, three component compound bases on epoxy resins, graded fillers and thixotropic agents using Sikadur 31 of Sika or equivalent make in Fosroc/ Thermax as approved by GE as per the technical specifications and manufacturer’s instructions complete all as specified and directed.

M&L for providing and application of one coat of Water based concrete curing compound with low viscosity wax emulsion using Sika Antisol E- WP of Sika or equivalent make in Fosroc/ Thermax as approved by Ge as concrete curing membrane over the applied polymer mortar as temporary curing membrane as per the technical specifications and manufacturer’s instructions complete all as specified and directed.

Providing and erecting hydraulic & manual steel props upto full height, braced at centre, resting on wedge and block to support the structure provisionally during repair work and maintaining them in position till required and as directed. Note : Hydraulic & manual steel props will be provided, erected and maintain the interval distance of steel props c/c at site on the basis of site reqmt as per direction of GE and Engr-in-Charge

M&L for applying 500gm raintite WPC with 1:2 CM on wall surface with help of brush (Brick Surface after taking down of cement plaster) complete as per the technical specifications and manufacturer’s instructions and directed by Engineer-in-charge.

M&L for applying Two Coats of Polymer modified cementious water proof coating with SikaTop® Seal-107 Over Raintite WPC with 1:2CM Layer thickness ~1.2-1.5 mm in 2 coats, Density ~2.0 kg/L (Part A+B mixed, +27ºC) (EN ISO 2811-1), Tensitle strength ≥ 2.0 N/mm2 (ASTM D412), Tensile adhesion strength ≥ 2.0 N/mm2 (ASTM D4541), Water penetration under pressure ~0mm penetration at 5 bar for 72 h (BS EN 12390-8), CFTRI Certificate for repeated use with aqueous foods/water as per USFDA 175.300 (TWO PACK POLYMER MODIFIED CEMENTITIOUS WATERPROOFING SLURRY AND PROTECTIVE COATING) in two coats @3kg/sqm as per the technical specifications and manufacturers instruction and directed by Engineer-in-charge

Taking down old damage cement plaster of any description racking out joints hacking for key, scrubbing down with water complete all as specified and as directed by Engr-in-Charge.

Demolition of brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed.

M&L brick work with sub class 'B' bricks straight or curved in plan exc 6 mtr mean radius built in CM (1:4) using old size bricks complete all as specified and directed.

M&L rendering 10 mm thick in CM 1:6 with and including mixing of liquid WPC of approved make @ 200ml per bag of cement / manufacturer's instructions on brick/concrete wall surfaces of any description, and finishing the surfaces even and fair complete complete all as specified and directed.

M&L for preparing new plastered or unplastered surfaces of walls and applying two coats of oil bound distemper over a coat of primer of same make complete all as specified and directed.

M&L rendering 15 mm thick in CM 1:4 with and including mixing of liquid WPC of approved make @ 200ml per bag of cement / manufacturer's instructions on brick/concrete wall surfaces of any description, and finishing the surfaces even and fair complete complete all as specified and directed.

M&L for preparing new plastered or unplastered surface of walls with 1mm thick wall care putty and a coat of primer and applying two coats of weather proof paint of approved shade/tint complete all as specified & as directed.

M&L for rendering 5mm thick in CM 1:3 as in ceiling/landing etc on concrete surface finish even and smooth without using extra cement complete all as specified and directed.

M&L for preparing new plastered or unplastered surfaces of ceiling and applying three coats of white wash on undecorated surface complete all as specified and directed.

M&L for preparing new plastered or unplastered surfaces of walls and applying three coats of white wash on undecorated surface complete all as specified and directed.

Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc. laid and beeded and pointed any cement mortar complete all as specified and directed.

M&L Granite (of any type), 18-20 mm thick machine cut laid over cement screed as in floor and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of the granite stone including cutting and polishing with and including 15mm thick screed bed or bedding in cement mortar 1:6 complete all as specified and directed.

M&L for rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified and directed.

Taking down chowkat or frame with shuters ( without taking off shutter from the frame) area exc 1.5 Sqm and n. exc 4.00 Sqm each

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 65 x 100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N(Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). ® Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. specification & drawing complete all as specified and directed.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 65 x 125 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). ® Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. specification & drawing complete all as specified and directed.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge (Note: stainless steel butt hinges and necessary S S screws shall be paid separately)

S&F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 35mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge (Note: stainless steel butt hinges and necessary S S screws shall be paid separately)

S&F stainless steel butt hinges medium weight of size 100 mm fixed with stainless screws complete all as specified and directed.

S&F 200mm size aluminium anodised, barrel tower bolt of extruded section complete all as specified and directed.

S&F extruded aluminium alloy handles 150 mm long fabricated type anodised complete all as specified and directed.

S&F in repair 250 mm long aluminium alloy anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts & sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed by Engr-in-Charge.

Dismantling roof tiles, single layer on roofs complete all as speified & directed.

M&L for 40mm thick brick tiles laid on cement mortar (1:6) 15mm thick and joints grouted flush in cement mortar (1:3) mixed with 5% of crude oil by weight of cement on mud phuska complete all as specified and as directed.

Laying/ fixing of 40mm thick brick tiles (retrived from Item No. 40 above) laid on cement mortar (1:6) 15mm thick and joints grouted flush in cement mortar (1:3) mixed with 5% of crude oil by weight of cement on mud phuska complete all as specified and as directed.

M&L Cutting or uprooting grass on old mud phuska, removing rubbish off the premises, Cleaning of the existing area by means acid etching, wire brushing, high pressure water jets complete in all respect and preparing to receive new mud/cement plaster complete all as specified and directed.

M&L for providing PCC 1:2:4 type B-0 (using 20mm graded stone aggregate) with maintain the proper roof slope as in bedding, coping and kerb complete all as specified and directed.

Supply and apply acrylic based waterproofing and heal reflecting system having following key performance properties: 1. Acrylic polymer dispersion single component liquid applied system. 2. Fully reinforced with glass fiber reinforced sika Fab or Equivalent The installation company of roofing system should be trained and authorized by Manufacturer & installation to be carried out as per manufactures approved method statement. All auxiliary & accessories involved during application should be supplied by single manufacture as a part of system. Any component used which is not manufacturer by the roofing manufacturer can only be used with official approval from manufacturer. Application system :- (a) Providing and Applying Primer Coat primer over the prepared surface with Sika® CoolCoat Primer or Equivalent Consumption @0.2-0.3 kg/m² (b) First coat: sika coolcoat or or Equivalent / Consumption @ 0.75 kg/m² (c) Fiber Reinforcement Make Sika or Equivalent (d)Second coat: sika coolcoat or Equivalent / Consumption @ 0.75 kg/m³ (e) Top Coat Sika® CoolCoat Primer or Equivalent Consumption @0.05-0.08 kg/m²

M&L for preparation of roof surfaces (old or new) with wire brush drying and cleaning to remove all foreign materials and washing with water to remove loose particles with and including providing 50 mm average thick PCC 1:2:4 type B-0 (using 20mm graded stone aggregate) with maintain the proper roof slope complete all as specified and directed.

M&L for providing 10mm thick polymer modified plaster in ratio 1:10 (1 part of polymer and 10 parts of cement with solid contents not less than 30%) over slab and applying priming coat of epoxy primer with resin and hardner with water dilution as per manufacturer instructions, applying 1st coat of solvent based polyurathene liquid membrane not less than 500 micron thick UV stable having SRI value greater than equal to 105 with consumption of 0.61 Kg/Sqm and applying 2nd coat solvent based polyurathene liquid mambrane not less than 500 micron thick UV stable having SRI value greater than liquid to 105 with consumption of 0.61 Kg/Sqm over dried 1st coat complete all as specified and directed. Make : Asian Paints / Pidilite / STP

Taking down old rusted & damaged steel windows/ventilators of any description and of any type & size with guard bars / grill including cutting holes for hold fasts & making good the disturbed portion complete all as specified & as directed.

S&F factory made mild steel windows (Box Type ) with side hung shutters including glazing bars to receive glass, dovetailed or welded with and including necessary welding, reveting, tower bolt, hanlde, holdfast, hinges and steel peg stay as per Drg No. CEJZ/TD-2013/01 sheet (1/3, 2/3, 3/3) complete all as specified and directed.

S&F steel ventilator with top hung shutter of glazed & gauged including hinges, steel peg stay complete with glazing bars including one shop coat of redoxide primer complete all as specified and directed.

S&F Sheet glass 4.00mm thick, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane

Dismantling water tank of capacity exceeding 500 liters but not excedding 1000 Ltrs complete all as specified and directed.

S&F in repair 1000 Ltrs capacity rotational moulded polyethylene water storage tanks double layered (cylindrical vertical with closed top) hoisted and fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc complete all as specified

Dismantling water tank of capacity exceeding 250 liters but not excedding 500 Ltrs complete all as specified and directed.

S&F rotational moulded polythene water storage tank 500 ltrs (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I complete all as specified and directed.

S&F in repairs 20mm bore dia ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 15mm-142gms/ 2 0 m m - 2 1 0 g m s . / 25mm-455gms/ 40mm - 690 gms) complete all as specified and directed.

S&F in repairs 20mm bore dia nipple suitable for HDPE water tank (Min weight 15mm-38 gms/20mm-45gms/25mm-65gms)fixed complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

M&L Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks, hand rails, cupboards frame and similar work con- forming to Fe.290.Gde-E-165 with and including necessary cutting and welding complete all as specified and directed.

Making 'V' Groove of 3 mm wide and 3 mm deep over crack line by electrically operated grinder with diamond concrete saw blade and cleaning it by Air Blower as directed.

Supply and apply of rust non shrink repair mortar for non moving cracks in plaster and walls Product Consumption : 25 RMT/Kg for crack size of 6mm x 6mm Density : 0.85 Kg/l at 27° C

Supply and Apply of ready to use water resistant White Cement Based Finishing/smoothing material in 1:5 mm thickness for indoor and outdoor plastered surfaces. Product Coverage :1.2 Kg powder/Sqm/mm thickness System Reinforcement : tensile adhesion > 1.0 N/mm2 at 28 days (According to EN 1348) water capillary Absorption 0.8 ml at 24 Hrs as per Karsten Tube Test, Water Retentivity > 98% (according to EN 196-3)

S&F in repair vitreous China, squatting pan, Orissa Pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) with PTMT trap of suitable size ( P or S type) including connection to trap and to flushing pipe, anti syphonic pipe etc complete including provision of cement concrete bedding & making good to floor complete all as specified and directed including taking out old one.

S&F in repairs 10 Ltr capacity PVC valveless syphonic action type flushing cistern low level white, with inlet, ball valve, float and handle including PVC flush pipe and brackets complete fixed in wall and floor to trap of WC as reqd complete all as specified and directed.

Taking up or down 15mm bore steel / composite / UPVC tubing and connection from any position concealed / exposed including cleaning for refixing or removal to store complete all as specified and directed by Engr-in-Charge.

S&F 20 mm dia steel water GI tube medium grade with all fittings / connections & MS clamps / clips and necessary screwing as reqd and fixed with or without concealed to walls & surface of roof slab with and including making good to required surfaces by using white cement complete all as specified and directed by Engr-in-Charge.

S&F 15 mm dia steel water GI tube medium grade with all fittings / connections & MS clamps / clips and necessary screwing as reqd and fixed with or without concealed to walls & surface of roof slab with and including making good to required surfaces by using white cement complete all as specified and directed by Engr-in-Charge.

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L for 25mm thick (1:2:4) Type-B-0 (using 12.5mm graded crushed stone aggregate) as in sub base of flooring complete all as specified and directed by Engr-in-Chargre.

M&L non skid ceramic tiles coloured pattern as required of 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with and including 15mm thick screed bed in CM (1:4) compete all as specified and directed.

M&L for Virified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in hite or coloured cement to matchincluding 15mm thick screed bed in CM (1:4) compete all as specified and directed

M&L for glazed ceramic coloured, designer & pattern (dark & light shade combination) tiles in 450 x 300 x 7-8 mm thick on vertical surfaces such as dado etc set and jointed in neat cement slurry and pointed in white or colour cement to match over with and including 10mm thick backing coat in CM 1:3 and complete all as specified and directed.

S&F in repair single/multi PVC (SWR) floor trap 75mm dia, palin with grating including joining to waster pipe, fixed in cement concrete type B-1 (1:2:4) using 20mm graded broken stone aggregate co,mplete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed.

M&L for Reinforced cement concrete M-30 (20mm graded graded graded aggregates) in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves etc complete all as specified and directed.

M&L TMT Mild steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips confirming to grade of steel Fe 500D complete all as specified and directed.

M&L TMT bars 5mm dia and over up to and including 10 mm dia cut to length bend to shape required including cranking, hooking ends and binding with and including MS wire (annealed) not less than 0.9 mm dia as in stirrups, spacers and binders complete all as specificed and as directed.

Taking down chowkats or frames with shutter (without taking off shutter from the frames) n. exc 1.50 Sqm each complete all as specified and directed.

S&F Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) Frame work for doors, windows, ventilators and partitions (Fixed portions) including shuterrs with Extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight,mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Chief.

S&F Sheet glass 4mm thick tinted glass ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane complete all as specified and directed.

Taking down old unservicable rolling shutter of any size and description compelete all as specified and directed.

S&F steel rolling shutters, without ball bearing, as specified including top covers, anchoring rod, hasp and staple and one shop coat of primer, erected in position as indicated, complete, gear operated type with bevel gear box and crank handle, 1.00 mm thickness of laths complete all as specified and directed.

Painting two coats with synthetic enamel paint over a coat of red oxide primer on new steel surfaces of any description over 10cm width or girth including preparation of surfaces and priming complete all as specified and directed.

Demolition and breaking up drain PVC (SWR) pipes jointed in cement mortar/solvent, internal dia of pipe upto 160mm in any position with wall or in floor at any height including necessary scaffolding if required as per direction of Engr-in-Charge complete all as specified and directed.

S&F 110 mm dia PVC (SWR) pipes single socketed in any length with rubber ring joint fixed to walls complete all as specified and directed.

S&F 75 mm dia PVC (SWR) pipes single socketed in any length with rubber ring joint fixed to walls complete all as specified and directed.

S&F 75 mm PVC (SWR) bends any radius with acess door complete all as specified and directed.

S&F 110 mm PVC (SWR) bends any radius with acess door complete all as specified and directed.

S&F 75 mm PVC (SWR) branch piece single (single Y) equal or unequal with access door complete all as specified and directed.

S&F 110 mm PVC (SWR) branch piece single (single Y) equal or unequal.with access door complete all as specified and directed.

S&F 110 mm PVC (SWR) junction single (T single) equal or unequal with acess door complete all as specified and directed.

S&F 75 mm PVC (SWR) junction single (T single) equal or unequal.with access door complete all as specified and directed.

M & L for fiber mesh 145 Gsm minimum above plastered surface of roof for water proof of roof/ crack/ patch/ wall repair etc complete all as specified and directed.

B B BUILDERS (BID ID -3267329)

malik constructions (BID ID -3265746)

M/S RAJINDER SINGH (BID ID -3265978)