Loading
Loading…
Loading…
Tender Value
₹84.6 L
EMD Value
₹1.7 L
Closing Date
26 May 2026, 3:30 pmClosed
No
No
Single Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
60 days
Expenditure
Capital (Works)
Above/Below/Par
DD TO SUR
14 conditions · 2 needing a document upload
The tenderer must have minimum average annual contractual turnover of V/N or V whichever is less, where V= Advertised value of the tender in crores of Rupees & N= Number of years prescribed for completion of work for which bids have been invited. The average annual contractual turnover shall be calculated as an average of 'total contractual payments" in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared/ audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover. The tenderers shall submit requisite information as per Annexure-VIB, along with copies of Audited Balance Sheets duly certified by the Chartered Accountant/ Certificate from Chartered Accountant duly supported by Audited Balance Sheet.
The tenderer must have successfully completed any of the following during last 07 (seven) years, ending last day of month previous to the one in which tender is invited: Three similar works each costing not less than the amount equal to 30% of advertised value of the tender, or Two similar works each costing not less than the amount equal to 40% of advertised value of the tender, or One similar work each costing not less than the amount equal to 60% of advertised value of the tender.
Defination of Similar Work :- Trenching cable laying location and signal foundation /erection/ termination wiring in connection with any Signaling work. OR Any Indoor or combined Indoor & Outdoor Signaling work including Supply, Installation testing and commissioning of relay interlocking (RRI/PI) system for passenger carrying lines.
4 conditions
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
Please refer to GCC with ACS & Instructions to tenderer attached in documents.
Signalling work in connection with Extension of shunting neck and converted into DN Goods loop line at Tilati station of Solapur Division.
SUR-N-T-2026-27-07
SUR-N-T-2026-27-07
Open
Works - General
12 Months
Solapur, Maharashtra
₹0
₹1.7 L
26 May 2026
28 Apr 2026
12 May 2026
115 items across 3 schedules · ₹76,63,347.27 total
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| 1 | Modification in existing EI system as per latest TAN, it includes:- Design and modification in existing interface and interlocking circuit of EI system, including modification in VDU,CCIP, MT, Data logger, EI, Relay rack complete wiring conforming to RDSO specification, as per technical requirement & tentative approved signaling plan/diagrams. Required hardware will be provided by railways except the wiring, material (i.e. connectors, interconnecting cable/wires, fuses etc.) The work includes supply of modified ST/LT, interface and logic circuit, CCIP/VDU diagram etc. to suit the approved interlocking plan. It also includes modification in data logger/MT, carrying out FAT, SAT jointly with railways and satisfactory commissioning of the modified EI with full complements as per approved IP and central railway practices. All plans and wiring diagrams shall be prepared on AUTOCAD and supplied in both soft copy and hard copies (6 sets.) Alteration involving modification in up to 10 routes.NOTE : If the alteration involves modification of routes up to 10, fixed cost as per the Rate mentioned in (i) above shall be paid. If the alteration involves modification of routes are more than 10 up to 20 routes, then, fixed cost as per the Rate mentioned in (ii) above shall be paid. | Per Alteration | 1.00 | 14,63,145 | 14,63,145 |
| 2 | Supply of Main cable Termination rack complete with scaffolding, fixtures & accessories including square bars for mounting 8-way terminal blocks, ladder, string rods, frame, base assembly, insulators, J bolt , nut/bolts & fasteners, backelite sheet, etc. Siemens type and as per extant practice of Central Railway. Typical part list as per Annexure-III and rack arrangement shall be as per sketch No.SK- 727 with latest alterations. | Set | 2.00 | 26,006 | 52,012 |
| 3 | Supply of low maintenance Lead Acid secondary cells 2V 80AH as per spec. IRS 88/2004 version 1.0 with latest amendments. | Numbers | 25.00 | 1,645 | 41,125 |
| 4 | Supply of Program switches, snap action, base mounting type along with cover and mounting bracket 63A-7 pole 3 position Siemens (3 LAO-63/7Y)/L&T/HEVELS type Drg.No.RST.C.106. | Numbers | 8.00 | 6,595 | 52,760 |
| 5 | Supply of Transformer 230V/110V-130V Single phase 1 KVA as per spec. IRS S-72/88 (Amd.2) with latest amendments. | Numbers | 2.00 | 6,571 | 13,142 |
| 6 | Supply of Battery charger self regulating floor mounting type with 230 V AC single phase input and output 110 V DC, 20 A as per spec.IRS.S.86/2000 (Amd.4) with latest amendments. | Numbers | 1.00 | 63,312 | 63,312 |
| 7 | Supply of Battery charger self regulating floor mounting type with 230 V AC single phase input and output 24 V DC, 20 A as per spec.IRS.S.86/2000 (Amd.4) with latest amendments. | Numbers | 6.00 | 27,268 | 1,63,608 |
| 8 | Supply of QNA1 AC immunized relay, 8F-8B, 24 VDC along with plug, board, retaining clip and connectors conforming to BRS:931A,IRS:S60/78 with Amendment no.1 , IRS:S34/68 with Amendment no.6 & IRS:S23/88 with Amendment no.1 | Numbers | 10.00 | 3,359 | 33,590 |
| 9 | Supply of QN1 Non AC immunized neutral relay, 8F-8B, 24 VDC along with plug, board, retaining clip and connectors conforming to BRS:930, IRS:S60/78 with Amendment no.1 , IRS:S34/68 with Amendment no.6 & IRS:S23/88 with Amendment no.1 | Numbers | 10.00 | 3,507 | 35,070 |
| 10 | Supply of QSPA1 relay, 24 V DC Slow to pick up, 8F- 4B along with plug, board, retaining clip and connectors conforming to BRS:933 IRS:S60/78 with Amendment no.1 , IRS:S34/68 with Amendment no.6 & IRS:S23/88 with Amendment no.1) | Numbers | 5.00 | 3,678 | 18,390 |
| 11 | Supply of QTA2 AC immunized track relay, 9 Ohm, 2F.1B, along with plug, board, retaining clip and connectors conforming to BRS:939A, 966 & Appendix F2, IRS:S34/68 with Amendment no.6 & IRS:S23/88 with Amendment no.1) | Numbers | 10.00 | 3,241 | 32,410 |
| 12 | Supply of Universal LED Lamp proving relay QECX61 relay, 4F-4B, AC conforming to BRS:941A STS/E/RELAYS/AC LIT LED SIGNAL/09-2002, Amdt.-1 (FOR ALL ASPECT ECR FOR AC LED SIGNAL) | Numbers | 10.00 | 3,317 | 33,170 |
| 13 | Resin cored wire as per specification No.IS:1921-1975 with Alloying element percentage as 63% SN (Tin) nd / 37% Pb (Lead) with percentage of various impurities not exceeding the values Sb (Antimony 0.2% maximum, Cu (Copper) 0.1% maximum, As (Arsenic) 0.05% maximum, Fe (Iron) 0.02% maximum & other impurities mainly AI, Zn & Cd shall be limited. The flux shall be free from corrosive action as per clause 5.2 & flux percentage may be used as per requirement. | Kg | 2.00 | 1,078 | 2,156 |
| 14 | Lacing thread rolls, black, wax coated (100 mtrs) | Numbers | 30.00 | 57 | 1,710 |
| 15 | Design, fabrication and supply of fuse Auto changeover system for 32 Nos external non detorating type fuses or 'G' type fuses from 0.6A Amp to 4A Amp capacities used in signaling circuits. System shall have 8 cards with monitoring arrangement of 4 fuses in one card. As per RDSO spec. RDSO/SPN/209/2012 Ver.2.0 or latest amendment if any. | Each Module | 6.00 | 23,147 | 1,38,882 |
| 16 | Supply of Main signal post 140 mm outer dia 4.6 Mtr Length as per spec No.IRS S 6/81 with latest amendments. | Numbers | 5.00 | 5,979 | 29,895 |
| 17 | Supply of Shunt signal post with Base (GI Pipe of 80 mm Dia of min. 1 meter length.) | Numbers | 6.00 | 2,650 | 15,900 |
| 18 | Supply of Cast Iron Main signal surface base 140mm as per spec No IRS: S-10 and Drg No 2011/M with latest amendments, with CLS Ladder assembly complete for CLS signal 5.5/4.5/3.5 mtrs long as per RDSO Drg no. SA 23156 (Adv), SA 23153 (Adv) & SA 23150 (Adv) Alt.1 respectively with Latest Amendment as the case may be for CLS unit & signal back staging as per extent C.Rly practice. | Numbers | 5.00 | 7,944 | 39,720 |
| 19 | Supply of Signal No.Plates as per Drg No RST-11393/ SK-842 | Numbers | 50.00 | 447 | 22,350 |
| 20 | Supply of A/AG/C/P/G/IB Board as per Drg. RST-11444/1(A), RDSO Drg No SA- 23460(AG), SA-23461(C) , RST-11445, SA 23456(P), SA 23477(G) & SA 23476-77 (IB) as applicable respectively with Latest Amendment. | Numbers | 5.00 | 476 | 2,380 |
| 21 | Supply of Stop Board / IB Board as per RST- 11791 (STOP BOARD)/ RDSO Drg No 7235/B as per extent C.Rly practice. | Numbers | 2.00 | 2,763 | 5,526 |
| 22 | Supply of Hand Cuff Locks / Godrej Navtal lock with Three common keys. | Numbers | 50.00 | 245 | 12,250 |
| 23 | Supply of "2 aspect" Signal Unit in FRP body without lenses and transformers as per RDSO Specification RDSO/SPN/194/2006/Rev.2.0 or latest complete and to suit LED signal Lamps and suitable for 140 mm dia post saves pigment finish on the back side of the and inside. white pigment finish inside the 2 aspect unit to avoid any extra paint cost | Numbers | 3.00 | 25,824 | 77,472 |
| 24 | Supply of "3 aspect" Signal Unit in FRP body without lenses and transformers as per RDSO Specification RDSO/SPN/194/2006/Rev.2.0 or latest complete and to suit LED signal Lamps and suitable for 140 mm dia post saves pigment finish on the back side of the and inside. white pigment finish inside the 4 aspect unit to avoide any extra paint cost | Numbers | 2.00 | 26,638 | 53,276 |
| 25 | Supply of Shunt Signal Position Light Type FRP complete as per RDSO Specification RDSO/SPN/194/2006/Rev.2.0 or latest with O ff set bracket 3-1/2" to be fitted on 140 mm post drawing No.SA23840(Adv) Alt-2 for dependent type complete with signal unit bracket, terminals etc without lenses, lamp, lamp holder, and to suit LED signal lamps. | Numbers | 6.00 | 11,731 | 70,386 |
| 26 | Supply of ARA Terminal blocks with links made of PBT Specn No.IRS/75/2006 (Rev - 2) with latest amendments and RDSO Drg.No.SA-23741A Alt.4., SA-23745 Alt.5, SA-23746, SA-23748 Alt.4, & SA-23756 Alt.3. | Numbers | 1000.00 | 65 | 65,000 |
| 27 | Supply of cartridge fuse block made of PBT as per RDSO Drg No SA-23748 Alt 4, SA- 23749 & Spec No.IRS S 75/2006 Rev.02 with latest amendment. Fuse block shall be suitable for round head type voltage fuses. | Numbers | 20.00 | 144 | 2,880 |
| 28 | Supply of round head type non detoriating type low voltage cartridge fuse as per specn No. IRS/S/78/92 with latest amendments - 2A/4A/6A capacity | Numbers | 40.00 | 62 | 2,480 |
| 29 | Supply of Tik-tak, piano type switches, 5 A (as per IS Specification). | Numbers | 6.00 | 30 | 180 |
| 30 | Supply of three pole plug and socket 5 Amp (as per IS Specification). | Numbers | 6.00 | 205 | 1,230 |
| 31 | Supply of Lamp 110V / 24W, 2 pin for Loc. | Numbers | 100.00 | 20 | 2,000 |
| 32 | Supply of Apparatus case with godown locks with detachable handle on both the doors.a) Single Case as per Drg No SK 783-1 & 2. with latest alteration. | Numbers | 3.00 | 14,252 | 42,756 |
| 33 | Supply of Apparatus case with godown locks with detachable handle on both the doors. b)Half Case as per Drg No SK 783-1 & 2. with latest alteration. | Numbers | 3.00 | 11,287 | 33,861 |
| 34 | Supply of earth electrode assembly as per Drg.No.CR/S&T/SK-815 | Numbers | 10.00 | 951 | 9,510 |
| 35 | Supply of Track Lead junction Boxes as per C.Rly Drg.No.RST 11509 made from fiber glass alongwith terminal blocks. | Numbers | 40.00 | 878 | 35,120 |
| 36 | Supply of Channel Pins single groove, galvanised, 7 mm suitable for 4mm dia bonding wire as per spec No. IRS: S 17-75 Revision 3. | Numbers | 5000.00 | 2 | 10,000 |
| 37 | Supply of PVC jacketed wire rope for Track lead connections. PVC jacketed wire rope should be of Galvanised steel wire rope 6mm dia (6x19 stranded wire with steel core of 6 mm dia) sheathed with PVC 2mm wall thickness, overall thickness being 10 mm. PVC sheath should be made of type 6 compound as per IS 5831 of 1984 Reaffirmed 2001 and steel wire rope as per IS: 2266:2019. Reclaimed for recycled material should not be used. | Metre | 2000.00 | 46 | 92,000 |
| 38 | Supply of 8 SWG GI wire (4mm dia) suitable for track circuit rail bonding. As per IRS Specification S:13-62 | Kg | 500.00 | 75 | 37,500 |
| 39 | Supply of William stretcher nylong insulation set suitable for ground connection as per RDSO drg No T-10367, T-10368, T-10384 as applicable and to the spec IRS S 23/88 with Amendment No.01 & 40/84 with Amendment No.01 or latest amendments. | Set | 20.00 | 452 | 9,040 |
| 40 | Supply of Tongue attachment nylon insulation set consisting of one inlsulating plate as per Drg no: RST-106961 & 3 nos of Ferrules with collars to suite rodding supplied as per RDSO spec & Drg.no: RST- 10692 | Set | 20.00 | 287 | 5,740 |
| 41 | Supply of Gauge Tie Plate nylong insulation as per RDSO drg No: T-10372 Alt2, T-10368, T-10371 Alt2, T-15083/88/Alt2 & T- 11690/Alt2 and to the spec IRS S 23/88 with Amendment No.01 & 40/84 with Amendment No.01 or latest amendments. | Set | 20.00 | 207 | 4,140 |
| 42 | Supply of Ground connections, complete set suitable for IRS type/appd. Point Machine for ordinary turnout with tounge attachment insulation and other insulation as per RDSO Drg.S/3361 /62 / 63 (for IRS type point machine) or RDSO Drg No.SA-9151/52 (for Siemens point machine) with latest a m e n d e m e n t s . However the ground connection shall be procured only after confirmation from Railway engineer as per site condition /type of machine/turnout. | Set | 3.00 | 7,018 | 21,054 |
| 43 | Supply of GI pipe, inner dia. 100mm dia. B- class as per spec. No.IS 1239 PT. 1/2004 or latest with sockets and fittings. TATA/JINDAL/ZENITH BIRLA make. | Metre | 60.00 | 908 | 54,480 |
| 44 | Supply of DWC HDPE pipe with one snap fit coupler and 'O' ring fire resistant, anti rodent, in 6 meter length of size 120 mm outer dia as per RDSO/SPN/204/2011 Ver 1.1 with Amd.1 or latest. | Metre | 60.00 | 288 | 17,280 |
| 45 | Supply of RCC pipes half round of size 150mm dia outer and 100 mm dia internal 1 mtr long matching to IS No.458/2003 amendment-1 with Rev.4. | Numbers | 1500.00 | 189 | 2,83,500 |
| 46 | Supply of modular terminal block of 2.5 sq. mm 2 IN 2 OUT type disconnect type terminal along with as per RDSO SPN/189/2004 Rev 3.0. The current capacity of 16 Amps and more. The terminal should have marking at centre to view description from front. Material to be procured from RDSO approved firms only. | Numbers | 1000.00 | 100 | 1,00,000 |
| 47 | Supply of DIN Channel for the terminals 1 Mtrs each | Numbers | 48.00 | 187 | 8,976 |
| 48 | Supply of End plates for modular terminal block | Numbers | 280.00 | 20 | 5,600 |
| 49 | Supply of End Clamp for modular terminal block | Numbers | 280.00 | 15 | 4,200 |
| 50 | Supply of Marker Card as per customer spec (10x10) | Numbers | 280.00 | 71 | 19,880 |
| 51 | Fuse terminals block with LED indication up to 2.5 sqmm screw type one in one out (suitable for (400 mA, 630mA, 1 A, 1.6 A, 2 A, 4A, 6.3 A & 10 A ) as per RDSO SPN/189/2004 Ver.03 or latest . (without fuse) | Numbers | 200.00 | 157 | 31,400 |
| 52 | End plate for through terminal block with LED indication. | Numbers | 100.00 | 12 | 1,200 |
| 53 | Fuse links of (400 mA, 630mA, 1 A, 1.6 A, 2 A, 4A, 6.3 A & 10A) | Numbers | 400.00 | 37 | 14,800 |
| 54 | Shorting link insulated Grey in colour | Numbers | 100.00 | 13 | 1,300 |
| 55 | Operating tool (operating tool, screw driver & stripper) as per Annexure-VII. | Numbers | 1.00 | 7,266 | 7,266 |
| 56 | Supply of Paints as per relevant IS specification preferably Asian / Apcolite/ Dulux make in different colour in one kg/2 kg pack | Kg | 50.00 | 306 | 15,300 |
| Schedule total | ₹34,13,310 | ||||
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
Instructions_To_Tenderer_TLT.pdf
ATTACHMENT
Special_Conditions_TLT.pdf
ATTACHMENT
GCC with ACS
ATTACHMENT
Tender_form_Annexure-I.pdf
ATTACHMENT
Cable_cut_policy_CR_1st_Sept_23.pdf Cable cut policy
ATTACHMENT
Inspection_Agency_Details.pdf
ATTACHMENT
Annexures__Drawings_TLT.pdf
ATTACHMENT
GCC_April-2022_with_ACS_11_13032026.pdf
ATTACHMENT
Cable_cut_policy_CR_1st_Sept_23.pdf
ATTACHMENT
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .