C/O Sports Hostel Block at GSSS Rohru

Amount

Earth work in excavation by mechanical means manual means in foundation trenches or drains up to all depth, including dressing of sides and ramming of bottoms, including getting out the excavated soil and disposal of surplus excavated soil upto dumping site which will be arranged by the contractor himself at his own cost including carriage in all leads and lifts by mechanical or manual means.

Supply and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete including carriage of materials in all leads and lifts by mechanical or manual means..

Providing form work with steel plates 3.15mm (Three point fifteen milimetre) thick welded with angle iron in frame 30x30x5 mm (Thirty into Thirty into five milimetre) so as to give a fair finish including centring, shuttering, strutting and propping etc. with wooden / steel battens and ballies, height of propping and centring below supporting floor to ceiling in all heights in all floors and removal of the same for in-situ reinforced concrete and plain concrete work in :-

Foundations, footings, bases of columns, etc. for mass concrete including carriage of materials upto all height with in all leads,lifts and other incidentals complete as per entire satisfaction of the Engineer-in-charge

Wall any thickness including carriage of materials upto all height with in all leads,lifts and other incidentals complete as per entire satisfaction of the Engineer-in-charge

Suspended floors, roofs, landings, balconies and access platform including carriage of materials upto all height with in all leads,lifts and other incidentals complete as per entire satisfaction of the Engineer-in-charge

Lintels, beams, plinth beams, girders,bressumers and cantilevers including carriage of materials upto all height with in all leads,lifts and other incidentals complete as per entire satisfaction of the Engineer-in-charge

Columns, Pillars, Piers, Abutments, Post and struts including carriage of materials upto all height with in all leads,lifts and other incidentals complete as per entire satisfaction of the Engineer-in-charge

Stairs, (excluding landings) except spiral Staircase including carriage of materials upto all height with in all leads,lifts and other incidentals complete as per entire satisfaction of the Engineer-in-charge

Edges of slabs and breaks in floors and walls.(a) Under 20 cm(Twenty centimetre) wide including carriage of materials upto all height with in all leads,lifts and other incidentals complete as per entire satisfaction of the Engineer-in-charge

Small lintels not exceeding 1.5 m (One point fifty metre) clear span, moulding as in cornices,window sills, string courses, bands, copings, bed plates, anchor blocks and the like.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level 1:5:10 (One cement : Five coarse sand: Ten graded stone aggregate 40 mm (Forty milimetre) nominal Size ,including all leads, lift & carriage of material & to the entire satification of the Engineer - in - charge.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level 1:4:8 (One cement : Four coarse sand: Eight graded stone aggregate 20 mm (Twenty milimetre) nominal Size) ,including all leads, lift & carriage of material & to the entire satification of the Engineer - in - charge.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level 1:4:8 (One cement : Four coarse sand: Eight graded stone aggregate 40 mm (Forty milimetre) nominal Size) ,including all leads, lift & carriage of material & to the entire satification of the Engineer - in - charge.

Providing & laying cement concrete in retaining walls, return walls, walls ( any thickness )including attached pilasters, columns, piers, abutments, pillars,posts,strurs,buttresses,string or lacing courses,parapets,coping, bed blocks, anchor blocks,plain windows sills, fillets,sunken floor etc. upto floor five lrvel, excluding the cost of centring,shuttering & finishing 1:3:6 (One cement : three coarse sand : six graded stone aggregate 20 mm nominal size), including all leads, lift & carriage of material & to the entire satification of the Engineer - in - charge.

Providing and laying in position specified grade of reinforced cement concrete1:1.5:3 (One cement :One point five coarse sand: Three graded stone aggregate 20 mm (Twenty milimetre) nominal size),excluding the cost of centering, shuttering, finishing and reinforcement in all work up to plinth level including carriage of materials in all leads and lifts by mechanical or manual means..

Providing and laying in position specified grade of reinforced cement concrete work1:1.5:3 (One cement :One point five coarse sand: Three graded stone aggregate 20 mm (Twenty milimetre) nominal size), in walls (any thickness), including attached pilasters, buttresses,plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement, including all leads, lift & carriage of material & to the entire satification of the Engineer - in - charge.

Providing and laying in position specified grade of reinforced cement concrete work 1:1.5:3 (One cement :One point five coarse sand: Three graded stone aggregate 20 mm (Twenty milimetre) nominal size), in beams, suspended floors, roofs having slope up to 15° (Fifteen degree) landings, balconies,shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing , including all leads, lift & carriage of material & to the entire satification of the Engineer - in - charge.

Steel reinforcement for R.C.C. work including straightening cutting, bending, placing in position and bindig all complete Thermo-Mechanically Treated bars of grade i.Fe-500D or more, including all leads, lift & carriage of material & to the entire satification of the Engineer - in - charge.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 ( Seven point five) in superstructure above plinth level up to floor V level in all shapes and sizes in cement mortar 1:6 ( One cement : Six coarse sand), including all leads, lift & carriage of material & to the entire satification of the Engineer - in - charge.

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 ( Seven point five) in superstructure above plinth level up to floor V level. In Cement mortar 1:4 (One cement : Four coarse sand), including all leads, lift & carriage of material & to the entire satification of the Engineer - in - charge.

Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (One cement : Two coarse sand : Four graded stone aggregate 20mm (Twenty milimetre) nominal size) including all leads, lift & carriage of material & to the entire satification of the Engineer - in - charge.

Providing & applying a coat of residual petroleum bitumen of grade of VG-10 (Ten)of approved quality using 1.7kg (One point seven kilogramme) per square metre on damp proof course after cleaning the surface with brushes and finally with apiece of cloth lightly soaked in kerosene oilincluding all leads, lift & carriage of material & to the entire satification of the Engineer - in - charge.

Supplying, filling, spreading & leveling (compacting) stone boulders of size range 5 cm (Five centimetre) to 10 cm (Ten centimetre), in soling under floor /recharge pit, in the required thickness,including all leads, lift & carriage of material & to the entire satification of the Engineer - in - charge.

Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (One cement : Six coarse sand : Twelve graded stone aggregate 20 mm(Twenty milimetre) nominal size) upto plinth level in cement mortar 1:6 (One cement : Six coarse sand),including all leads, lift & carriage of material & to the entire satification of the Engineer - in - charge.

Providing and fixing 100 mm(one hundred milimetre) PVC weep hole pipe 1st brick / stone masonary/ plain concrete/ RCC in abutment/wingwall/ retaining wall extending through to the full length of structure in slop of 1:20 ( One into twenty) toward drawing face complete as per drawing and technical specification clause 614/78,1204.3,71/6 retaining walls and breast walls,including all leads,lifts and carriage of materials and other incidental charges complete as per entire satisfaction of the Engineer-in-charge.

Providing and fixing Second class Deodar wood 37.5 mm (Thirty seven point five milimetre) thick shutters panelled or panelled and glazed shutters for doors,windows and clerestory windows, including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note:- Butt hinges and necessary screws shall be paid separately),including all leads, lift & carriage of material & to the entire satification of the Engineer - in - charge.

Providing and fixing Second class Deodar wood 35 mm (Thirty Five milimetre) thick wire gauge shutters using galvanized M.S. wire gauge of average width of aperture 1.4 mm (One point four milimetre) in both directions with wire of dia 0.63 mm (Zero point six three), for doors, windows and clerestory windows with hinges and necessary screws ,including all leads, lift & carriage of material & to the entire satification of the Engineer - in - charge.

Providing and fixing ISI marked Factory made flush door shutters 35 mm (Thirty five milimetre) thick ( commercial Board) conforming to IS : 2202 (Two thousand two hundred two) (Part I) non-decorative Phenol bonded Termite resistant and boiling water proof core of block board construction with full frame of first class hard wood and well matched commercial three ply veneer with vertical grains or cross and of Centuary ply boards Ltd./ Kit Ply/ Green ply or its equivlent as per Arch. drawing, including all leads, lift & carriage of material & to the entire satification of the Engineer - in - charge.

Providing and fixing ISI marked Factory made flush door shutters 25 mm (Twenty five milimetre) thick for Cup Board ( commercial Board) conforming to IS : 2202 (Two thousand two hundred two) (Part I) non-decorative Phenol bonded Termite resistant and boiling water proof core of block board construction with full frame of first class hard wood and well matched commercial three ply veneer with vertical grains or cross and of Centuary ply boards Ltd./ Kit Ply/ Green ply or its equivlent as per Arch. drawing including all leads, lift & carriage of material & to the entire satification of the Engineer - in - charge.

Providing and fixing Teak first class hard wood cornice of size 75x50 mm (Seventy five into fifty milimetre) size fixed over wood wool tile panelling as per arch. drawing fixed with steel self screws in all heights and floor levels ,including all leads, lift & carriage of material & to the entire satification of the Engineer - in - charge.

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 (Ten) as per IS : 1868 (one thousand eight hundred sixty eight)), transparent or dyed to required colour or shade, with nuts and screws etc.complete including all leads, lift & carriage of material & to the entire satification of the Engineer - in - charge. :

300x16 mm (Three hundred into sixteen milimetre).

250x16 mm (Two hundred fifty into sixteen milimetre).

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 (Ten) as per IS : 1868 (one thousand eight hundred sixty eight) ) transparent or dyed to required colour or shade, with necessary screws etc. complete including all leads, lift & carriage of material & to the entire satification of the Engineer - in - charge

200x10 mm (Two hundred into ten milimetre).

100x10 mm (One hundred into ten milimetre).

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 (Ten) as per IS : 1868 (one thousand eight hundred sixty eight)) transparent or dyed to required colour or shade, withnecessary screws etc. Complete including all leads, lift & carriage of material & to the entire satification of the Engineer - in - charge.

125 mm ( One hundred twenty five milimetre)

100 mm ( One hundred milimetre)

75 mm ( Seventy five milimetre)

Providing and fixing 115 mm (One hundred fifteen milimetre) long bright finished brass hasp and staple (safety type) with necessary screws etc. complete including all leads, lift & carriage of material & to the entire satification of the Engineer - in - charge

Providing and fixing150mm (One hundred milimetre) long oxidised M.S. double acting spring hinges with necessary screws etc. Complete including all leads, lift & carriage of material & to the entire satification of the Engineer - in - charge

Providing and fixing aluminium casement stays, ISI marked, anodised (anodic coating not less than grade AC 10 (Ten) as per IS : 1868 (one thousand eight hundred sixty eight)) transparent or dyed to required colour and shade, with necessary screws etc. Complete including all leads, lift & carriage of material & to the entire satification of the Engineer - in - charge.

Providing and fixing aluminium hanging floor door single rubber stopper, ISI marked, anodised (anodic coating not less than grade AC 10 (Ten) as per IS : 1868 (one thousand eight hundred sixty eight)) transparent or dyed to required colour and shade, with necessary screws etc. Complete, including all leads, lift & carriage of material & to the entire satification of the Engineer - in - charge.

Providing and fixing Triple strip vertical type magnetic catcher of approved quality in cupboard/ ward robe shutters, including fixing with necessary screws etc. Complete, including all leads, lift & carriage of material & to the entire satification of the Engineer - in - charge.

Providing and fixing 20 mm (Twenty milimetre) dia (heavy type) nickel plated M.S. pipe curtain rods with nickel plated brackets, including all leads, lift & carriage of material & to the entire satification of the Engineer - in - charge.

Providing and fixing ISI marked 25 mm (Twenty five milimetre) thick including ISI marked nickel plated bright finished M.S.piano hinges with necessary screws. flush door shutters conforming to IS : 2202 (Two thousand two hundred two) (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 (Three) ply veneering with vertical grains or cross bands and face veneers on front side and 0.60 mm (Zero point six zero) thick PGI sheet lining on inner side of shutters, including all leads, lift & carriage of material & to the entire satification of the Engineer - in - charge.

Providing and fixing IS : 12817 (Twelve thousand eight hundred seventeen) marked stainless steel butt hinges with stainless steel screws etc. welded to M.S frame complete,including all leads, lift & carriage of material & to the entire satification of the Engineer - in - charge. :

125x64x1.90 mm (One hundred twenty five into sixty four into one point ninety milimetre).

100X58X1.90 mm (One hundred into fifty eight into one point ninety milimetre).

75x47x1.80 mm (Seventy five into forty seven into one point eighty milimetre).(Windows+vent)

Providing and fixing powder coated telescopic drawer channels 300 mm (Three hundred milimetre) long with necessary screws etc.complete, including all leads, lift & carriage of material & to the entire satification of the Engineer - in - charge. :.

Providing and fixing sliding arrangement in racks/ cupboards/cabinets shutter by with stainless steel rollers to run inside C or E aluminium channel section (The payment of C or E channel shall be made separately), including all leads, lift & carriage of material & to the entire satification of the Engineer - in - charge. :

Providing and fixing 6 mm (Six milimetre) thick flat pressed commercial ply exterior grade (Grade I (One)) or graded wood particle board IS : 3087 (Three thousand eighty seven) marked lining , to frame, backing or studding with screws etc. complete (Frames, backing or studding to be paid separately), including all leads, lift & carriage of material & to the entire satification of the Engineer - in - charge.

Providing and fixing second class Kail wood work in frames of false ceiling, partitions etc. sawn and fixed in position, including all leads, lift & carriage of material & to the entire satification of the Engineer - in - charge.

Providing and fixing 12 mm (Twelve milimetre) thick & 80 cm (Eighty centimetre) wide first class Rai wood border in ceiling fixed over iron or wood frame work which shall be paid for separately as per Architectural drawing complete fixed with steel fastener at all heights and floor levels,including all leads, lift & carriage of material & to the entire satification of the Engineer - in - charge.

Providing and fixing 19 mm (Nineteen milimetre) thick Commercial water proof Board IS : 3087 (Three thousand eighty seven) marked, in shelves and partions with screws and fittings wherever required, edges to be painted with polyurethane primer (fittings to be paid separately), including all leads, lift & carriage of material & to the entire satification of the Engineer - in - charge.

Providing and fixing second class teak wood lipping/ moulded beading or taj beading of size 19X5 mm ( Nineteen into five milimetre)fixed with wooden adhesive of approved quality and screws/nails on the edges of the Pre-laminated particle board, including all leads, lift & carriage of material & to the entire satification of the Engineer - in - charge.

Providing & fixing glass panes with putty and glazing clips in steel doors,windows, clerestory windows, all complete with : (i) 4 mm (Four milimetre) thick glass panes ( double glass ), including all leads, lift & carriage of material & to the entire satification of the Engineer - in - charge.

Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2 mm (Twenty into ten into two milimetre) and braced with flat iron diagonals 20x5 mm (Twenty into five milimetre) size, with top and bottom rail of T-iron 40x40x6 mm (Forty into forty into six milimetre), with 40 mm (Forty milimetre) dia steel pulleys, complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of approved steel primer, including all leads, lift & carriage of material & to the entire satification of the Engineer - in - charge.

Structural steel work in single section, welded and fixed with or without connecting plate such as Door, window chowkhats etc. and the like,including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete,including all leads, lift & carriage of material & to the entire satification of the Engineer - in - charge.

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete including all leads, lift & carriage of material & to the entire satification of the Engineer - in - charge.

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works as required including all leads, lift & carriage of material & to the entire satification of the Engineer - in - charge. :

Providing and fixing 10 cm (Ten centimetre) dia M.S post embeded in cement concrte base with MS flat 50x5 mm (Fifty into five milimetre) cleat in base (cement concrete will be paid for separately), including all leads, lift & carriage of material & to the entire satification of the Engineer - in - charge.

Supplying and fixing 80x1.25 mm (Eighty into one point twenty five milimetre) M.S. laths with 1.25 mm (One point twenty five milimetre) thick top cover rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm (Twenty seven point five centimetre) long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454(four thousand four hundred fifty four) part-1(One) and M.S. top cover of required thickness for rolling shutters, including all leads, lift & carriage of material & to the entire satification of the Engineer - in - charge.

Providing and fixing ball bearing for rolling shutters, including all leads, lift & carriage of material & to the entire satification of the Engineer - in - charge.

Providing and fixing hand rail Bombay pipe of 5 cm (Five centimetre) dia or rectangular hollow pipe section 75x40 mm (Seventy five into forty milimetre) of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approved steel primer, including all leads, lift & carriage of material & to the entire satification of the Engineer - in - charge.

Providing and fixing M.S. grills of required approved pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.(a)Fixed to steel windows by welding, including all leads, lift & carriage of material & to the entire satification of the Engineer - in - charge. :

Providing and fixing M.S. fan clamp type I (One) or II(Two) of 16 mm (Sixteen milimetre) dia M.S. bar, bent to shape with hooked ends in R.C.C. slabs or beams during laying, including painting the exposed portion of loop, all as per standard design complete, including all leads, lift & carriage of material & to the entire satification of the Engineer - in - charge.

Providing and fixing 75x75 cm (Seventy five into seventy five centimetre) size Ornamental M.S brackets made of 50x50 (Fifty into fifty) & 20x20 mm (Twenty into twenty milimetre) hollow section dully welded or rivtted in combination as per Architectural detail/ drawing complete in all respect dully fixed with welded or self screws / fastners in wall etc as required and applying of two coat of red lead paint as directed by the Engineer-in-Charge at all heights and all floor levels,including all leads, lift & carriage of material & to the entire satification of the Engineer - in - charge.

Providing and fixing first quality ceramic glazed wall tiles of size 30x45 cm (Thirty into forty five centimetre) conforming to IS: 15622(Fifteen thousand six hundred twenty two) (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm(twelve milimetre) thick bed of cement mortar 1:3 (One cement : Three coarse sand) and jointing with grey cement slurry @ 3.3kg(Three point three kilogramme) per square metre, including pointing in white cement mixed with pigment of matching shade complete,including all leads, lift & carriage of material & to the entire satification of the Engineer - in - charge. .

Providing and laying precast cement concrete pavers 40 mm(forty milimetre) thick laid over a bed of cement mortar 1:4 ( one cement :four sand) 25 mm (Twenty five milimetre) thick laid in floors, jointed with neat cement slurry mixed with pigment to match the shade of the pavers as per detail of Arch. drg. complete in all respect, including all leads, lift & carriage of material & to the entire satification of the Engineer - in - charge.

Providing and laying precast cement concrete pavers 25 mm (Twenty five milimetre) thick of Nitco or equivlents factory make laid over a bed of cement mortar 1:4 ( one cement :four sand) 25 mm (Twenty five milimetre) thick laid in floors, jointed with neat cement slurry mixed with pigment to match the shade of the pavers as per detail of Arch. drg. complete,including all leads, lift & carriage of material & to the entire satification of the Engineer - in - charge.

Kota stone slab flooring 25 mm (Twenty five milimetre) thick of 55 cm x55 cm (Fifty five into fifty five centimetre)size of uniform color over 20 mm(Twenty milimetre) (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (one cement : four coarse sand) ,including all leads, lift & carriage of material & to the entire satification of the Engineer - in - charge.

Kota stone slabs 20 mm(Twenty milimetre) thick in risers of steps, skirting, dado and pillars laid on 12 mm(Twlve (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete,including all leads, lift & carriage of material & to the entire satification of the Engineer - in - charge.

Kota stone slabs 20 mm to 25 mm (twenty milimetre to twenty five milimetre) thick in stair steps with single piece having semi round nosing , laid on 12 mm(twelve milimetre) (average) thick cement mortar 1:3 (one cement: three coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing completeincluding all leads, lift & carriage of material & to the entire satification of the Engineer - in - charge.

Providing and fixing 18 mm (Eighteen milimetre) thick Baroda Green Marble or equivelent saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills,facias and similar locations of required size, approved shade, colour and texture laid over 20 mm (Twenty milimetre)thick base cement mortar 1:4 (One cement : Four coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups,including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete in all floor levels, including rubbing and polishing complete,including all leads, lift & carriage of material & to the entire satification of the Engineer - in - charge.

Providing and fixing Wood wool Tile of approved thikness in panelling over wooden frame work 35x50 mm (Thirty five into fifty milimetre)@ 60cm (Sixty centimetre) center to center horizontly and vertically upto all height with cornice of size 75x50 mm (Seventy five into fifty milimetre) fixed with fastners / self screws or as directed by the Engineer at all heights and floor levels complete( wood frame work and cornice will be paid separately). ,including all leads, lift & carriage of material & to the entire satification of the Engineer - in - charge.

Providing and fixingr wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ tone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges,including all leads, lift & carriage of material & to the entire satification of the Engineer - in - charge.

Providing and fixing 18 mm(Eighteen milimetre) thick Raj Nagar Plain white marble/ Udaipur or equivelent having grey streaks saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills,facias and similar locations of required size, approved shade, colour and texture laid over 20 mm(Twenty milimetre) thick base cement mortar 1:4 (One cement : Four coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups,including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete in all floor levels, including rubbing and polishing complete,including all leads, lift & carriage of material & to the entire satification of the Engineer - in - charge.

40 mm (Forty milimetre)thick cement concrete flooring 1:2:4 (one cement : two coarse sand : four graded stone aggregate20mm(Twenty milimetre) nominal size) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. Complete including rubbing and polishing complete,including all leads, lift & carriage of material & to the entire satification of the Engineer - in - charge.

Providing and fixing 3.9 mm(Three point nine milimetre) thick Tera Flex Flooring of approved shade of GENFLOR over Cement concrete flooring as per Approved Architectural drawing / required specifications complete at all floor levels,including all leads, lift & carriage of material & to the entire satification of the Engineer - in - charge.

Providing and fixing AEROLITE Armstrong Tiles of size 60x60 cm(Sixty into sixty centimetre), 50%(Fifty percent) fully perforated & 50%(fifty percent) plain tiles in combination over powder coated G.I frame work as per pattern with 12 mm(Twelve milimetre) thick & 80 cm(Eighty centimetre) wide Rai wood border.( Rai wood border will be paid separately),including all leads, lift & carriage of material & to the entire satification of the Engineer - in - charge.

Providing and fixing 0.61 mm(Zero point sixty one milimetre) thick with zinc coating not less than 275 gm/ m² (Two hundred seventy five gramme per square metre) pre-painted corrugated G.S. sheet roofing(TATA MAKE or its equivlent as approved by the Engineer) including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm Eight milimetre) diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required,including all leads, lift & carriage of material & to the entire satification of the Engineer - in - charge.

Providing and fixing 0.63 mm(Zero point sixty three milimetre) thick with zinc coating not less than 275 gm/ m² (Two hundred seventy five gramme per square metre) pre-painted plain G.S. sheet (TATA MAKE or its equivlent as approved by the Engineer ) ridges or hips of width 60 cm (Sixty centimetre)overall width plain G.S. sheet fixed with polymer coated J or L hooks, bolts and nuts 8 mm(Eight milimetre) dia G.I. limpet and bitumen washers complete,including all leads, lift & carriage of material & to the entire satification of the Engineer - in - charge.

Providing and fixing1.60 mm (One point six zero milimetre) thick with zinc coating not less than 350 gm/m²(Three hundred fifty gramme per square metre) pre-painted plain G.S. sheet (TATA MAKE or its equivlent as approved by the Engineer) valleys of 90 cm(Ninety centimetre) wide overall in plain G.S. sheet fixed with polymer coated J, or L hooks, bolts and nuts 8 mm(Eight milimetre) dia G.I. limpet and bitumen washers complete,including all leads, lift & carriage of material & to the entire satification of the Engineer - in - charge.

Providing and fixing 0.63 mm (Zero point six three milimetre) thick with zinc coating not less than 275 gm/m²(Two hundred seventy five gramme per square metre) pre-painted plain G.S. sheet (TATA MAKE or its equivlent as approved by the Engineer) fixing 30 cm(Thirty centimetre) wide, 30 cm (Thirty centimetre) deep overall semicircular plain G.S. sheet gutter with iron brackets 40x3mm(Forty into three milimetre) size, bolts, nuts and washers etc., including making necessary connections with rain water pipes complete,including all leads, lift & carriage of material & to the entire satification of the Engineer - in - charge.

Providing fixing 2 mm (Two milimetre) thick M.S B.P. sheet roofing welded on angle iron frame work and flats frame work further finished with 19x19 mm/10x10mm(Nineteen into nineteen milimetre/ten into ten milimetre) hollow square bars from out side @ 15 cm(Fifteen centimetre) center to center / 10 cm (Ten centimetre) center to center respectively and also applying red lead primer two coats complete as per approved Architectural drawings in all heights ( frame work of iron shall be paid separately),including all leads, lift & carriage of material & to the entire satification of the Engineer - in - charge.

Providing 2.00(Two point zeo ) M.S sheet cieling, soffits of chhajas and facia welded over angle/T-iron 25x25x5 mm(Twenty five into twenty into five milimetre) or as directed by the Engineer complete also applying red lead primer two coats with iron screws or as per drawing in all respect up to all floor levels ( frame work will be paid for separately),including all leads, lift & carriage of material & to the entire satification of the Engineer - in - charge.

Providing and fixing of 38 cm (THirty eight centimetre) overall width plain G.S. Prepainted sheet flashing of TATA make or its equivlent as approved by the Engineer fixed with polymer coated J or L hooks, bolts and nuts, G.l. limpet and bitumen washer complete,or with self screws bent to shape and fixed in wall with cement mortar 1:3 (one cement : three coarse sand),including all leads, lift & carriage of material & to the entire satification of the Engineer - in - charge.

Providing and fixing M.S. holder bat clamps of approved design to C.I. or S.C.I. or M.S rectangular rain water pipes embedded in cement concrete blocks 10x10x10 cm(Ten into ten into ten centimetre) of 1:2:4 mix (one cement : two coarse sand : four graded stone aggregate 20 mm(Twenty milimetre) nominal size) and cost of cutting holes and making good the walls etc.,including all leads, lift & carriage of material & to the entire satification of the Engineer - in - charge.

150 mm dia

75 mm dia

Providing and fixing M.S rectangular rain water pipes including jointing with lead complete and fixing to walls at all heights and floor level as per drawing/ direction of Engineer. ( Cost of lead shall be paid separately),including all leads, lift & carriage of material & to the entire satification of the Engineer - in - charge.

150mm dia

110 mm dia

150mm dia

110 mm dia

Providing lead caulked joints to sand cast iron/ M.S rain water pipes and fittings,including all leads, lift & carriage of material & to the entire satification of the Engineer - in - charge. ::

150mm dia

110 mm dia

6 mm(Six milimetre) thick cement plaster on ceiling with cement mortar 1:3 (one cement : three fine sand),including all leads, lift & carriage of material & to the entire satification of the Engineer - in - charge.

15 mm(Fifteen milimetre) thick cement plaster on rough side of single or half brick / concrete block wall upto all floor level and heights with cement mortar1:4 (one cement: four coarse sand),including all leads, lift & carriage of material & to the entire satification of the Engineer - in - charge.

15 mm(Fifteen milimetre) thick cement plaster on rough side of single or half brick / concrete block wall upto all floor level and heights with cement mortar1:6 (one cement: six coarse sand),including all leads, lift & carriage of material & to the entire satification of the Engineer - in - charge.

15 mm (fifteen milimetre) thick cement plaster on fair side of single or half brick / concrete block wall upto all floor level and heights with cement mortar1:6 (one cement: six coarse sand),including all leads, lift & carriage of material & to the entire satification of the Engineer - in - charge.

20 mm(Twenty milimetre) thick cement plaster in pattern to imitate stone masonry and horizontal bands as per Arch. Detail/ drawings on rough side of single or half brick / concrete block wall upto all floor level and heights with cement mortar1:4 (one cement: four coarse sand),including all leads, lift & carriage of material & to the entire satification of the Engineer - in - charge.

Providing and applying two coats of white cement based putty of average thickness 2 mm (Two milimetre), of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete,including all leads, lift & carriage of material & to the entire satification of the Engineer - in - charge.

Distempering with first quality Synthetic/acrylic distemper (ready mixed) of Asian/Nerolac Paint of approved shade and colour complete as per manufacturer's specification two or more coats on new work to give an even shade and final finish after throughly cleaning the surface of all dirt, dust and other foreign matters and sand papering Smooth.including carriage of materials upto all leads and lifts also and as per the direction of Engineer-in-Charge

Finishing walls with 100%(one hundred percent) Premium acrylic emulsion/Apex Ultima paint of Asian/Nerolac brand having VOC less than 50 gm/litre(fifty gramme per litre) and UV resistance as per IS 15489:2004(fifteen thousand four hundred eighty nine : two thousand four), Alkali & fungal resistance, dirt resistance paint of required shade (Company Depot Tinted) with silicon additives to give an even shade and final finish after throughly cleaning the surface of all dirt, dust and other foreign matters and sand papering Smooth on new work (Two or more coats applied @ 1.43 litre/ 10 sqm (one point four three litre per ten square metre). over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm.(zero point nine zero litre per ten square metre),including carriage of materials upto all leads and lifts also and as per the direction of Engineer-in-Charge.

Finishing walls with Premium Acrylic Smooth exterior weather proof paint ( Apex ultima) with Silicone additives of required shade to give an even shade and final finish after throughly cleaning the surface of all dirt, dust and other foreign matters and sand papering Smooth on new work (Two or more coats applied @ 1.43 litre/ 10 sqm (one point four three litre per ten square metre). over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm.(zero point nine zero litre per ten square metre),including carriage of materials upto all leads and lifts also and as per the direction of Engineer-in-Charge.

Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications,Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 litre/10 sqm.(zero point nine zero litre per ten square metre), over an under coat of primer applied @ 0.80 ltr/ 10 sqm.(zero point eighty litre per ten square metre) of approved brand and manufacture,including carriage of materials upto all leads and lifts also and as per the direction of Engineer-in-Charge.

Applying priming coat With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood) to give an even shade and final finish after throughly cleaning the surface of all dirt, dust and other foreign matters and sand papering, including carriage of materials upto all leads and lifts also and as per the direction of Engineer-in-Charge.

Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 litre/10 sqm.(zero point nine zero litre per ten square metre), over an under coat of primer applied @ 0.75 ltr/ 10 sqm.(zero point seventy five litre per ten square metre) of approved brand and manufacture,including carriage of materials upto all leads and lifts also and as per the direction of Engineer-in-Charge.

French sprit polishing on new wood work ( Two or more coats on new works including a coat of wood filler) of approved brand and manufacturere complete in all respect at all heights and floor levels,including carriage of materials upto all leads and lifts also and as per the direction of Engineer-in-Charge.

Cutting holes of required size in brick masonry wall for fixing of exhaust fan including providing and fixing 75 mm(Seventy five milimetre) to /150 mm(One hundred fifty milimetre) dia PVC pipes conforming BIS-12818 (Twelve thousand eight hundred eighteen)and making good the same etc. complete,including carriage of materials upto all leads and lifts also and as per the direction of Engineer-in-Charge.

Providing and laying APP (Atactic Polypropylene Polymer) modified prefabricated five layer, 3 mm (three milimetre) thick water proofing membrane, black finished reinforced with glass fibre matt consisting of a coat of bitumen primer for bitumen membrane @ 0.40 litre/sqm(zero point four zero litre per square metre) by the same membrane manufactured of density at 25°C(twenty five degree celsius), 0.87 - 0.89 kg/litre(zero point eight seven - zero point eight nine kilogramme per litre) and viscocity 70 - 160 cps.(seventy - one hundred sixty) Over the primer coat the layer of membrane shall be laid using butane torch and sealing all joints etc., and preparing the surface complete. The vital physical and chemical parameters of the membrane shall be as under : Joint strength in longitudinal and transverse direction at 23°C(twenty three degree celsius) as 350/300 N/ 5 cm.(three hundred fifty / three hundred n / five centimetre) Tear strength in longitudinal and transverse direction as 60/80N(sixty/eighty N). Softening point of membrane not less than 150°C.(one hundred fifty degree celsius) Cold flexibility shall be upto -2°C(minus two degree celsius) when tested in accordance with ASTM, D - 5147(five thousand one hundred forty seven). The laying of membrane shall be got done through the authorised applicator of the manufacturer of membrane :(i) 3 mm (three milimetre) thick ,including carriage of materials upto all leads and lifts also and as per the direction of Engineer-in-Charge.

Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete ,including carriage of materials upto all leads and lifts also and as per the direction of Engineer-in-Charge.

25 to 40 mm (twenty five to forty milimetre) nominal bore.

Fixing water meter and stop cock in G.I. pipe line including cutting and threading the pipe and making long screws etc. complete (cost of water meter and stop cock to be paid separately) including carriage of materials upto all leads and lifts also and as per the direction of Engineer-in-Charge.

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm (one hundred milimetre) sand cast Iron P or S trap, 10(ten) litre low level white P.V.C. flushing cistern No.21001 including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: (i) White Vitreous china Orissa pattern W.C. pan No.2071 of size 580x440 mm with integral type foot rests of Cera or Hindware or its equivlent make ,including all leads,lifts and carriage of materials and other incidental charges complete as per entire satisfaction of the Engineer-in-charge.

Providing and fixing water closet squatting pan (Indian type W.C. pan ) withquatting pan or European type water closet (Anglo Indian W.C pan No.20012 of Cera or Hindware or its equivlent make ) with seat & lid fixed with C.P. brass hinges and rubber buffers, 10(ten) litre low level flushing cistern No.21001 with fitting and brackets, 40 mm(forty milimetre) flush bend, 20 mm(twenty milimetre) over flow pipe, with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required,including all leads,lifts and carriage of materials and other incidental charges complete as per entire satisfaction of the Engineer-in-charge.

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan of Cera or Hindware or its equivlent make ) with seat and lid, 10 (ten)litre low level white P.V.C. flushing cistern no.21001,including flush pipe, with manually controlled device (handle lever),conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required,including all leads,lifts and carriage of materials and other incidental charges complete as per entire satisfaction of the Engineer-in-charge.

(WC for disabled person.

Providing and fixing 8 mm(eight milimetre) dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge ,including all leads,lifts and carriage of materials and other incidental charges complete as per entire satisfaction of the Engineer-in-charge.

Providing and fixing White Vitreous China Wash basin No. 10001 of size 550x400 mm (five hundred fifty into four hundred milimetre) with a 15 mm (fifteen milmetre) CP Brass single hole basin mixer of Cera ,Hindware or its equivlent make with C.I. brackets of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required ,including all leads,lifts and carriage of materials and other incidental charges complete as per entire satisfaction of the Engineer-in-charge.

Providing and placing on terrace (at all floor levels) PVC water storage tank, IS : 12701 marked, Sintex or its equivlent make with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank including carriage of materials upto all leads and lifts also and as per the direction of Engineer-in-Charge.

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.(a)Semi Rigid 40mm(forty milimetre) dia,including all leads,lifts and carriage of materials and other incidental charges complete as per entire satisfaction of the Engineer-in-charge.

Providing and fixing 610x510 mm (six hundred ten into five hundred ten milimetre) bowl depth 200 mm (two hundred milimetre)Stainless Steel double with drain board Super Deluxe No.6321 of Diamond or its eqivelent A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required,including all leads,lifts and carriage of materials and other incidental charges complete as per entire satisfaction of the Engineer-in-charge.

Providing & fixing Vitreous China bowl pattern urinal including connecting the Urinalwith waste pipe by means of white lead mixed with chopped ( Waste pipe to bemeasured & paid for separately ) Flat back type size 430 x 260 x 350 ( Four hundred thirty into two hundred sixty into three hundred fifty ) milimeter, as per HP.PWD.,specification, including carriage of all labour equipment & materials to various location through all modes of including carriage transportation in all leads, lifts,including all incidental charges.

Providing and fixing for external work G.I. pipes complete with G.I. fittings including trenching and refilling etc.including carriage of materials upto all leads and lifts also and as per the direction of Engineer-in-Charge.

25 mm (twenty five milimetre) dia nominal bore

Providing and fixing 25 mm (twenty five milimetre) dia nominal bore G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. Internal work-Exposed on wall,including carriage of materials upto all leads and lifts also and as per the direction of Engineer-in-Charge.

Providing and fixing G.I. Pipes complete with G.I. fittings and clamps, i/c making good the walls etc. concealed pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall including carriage of materials upto all leads and lifts also and as per the direction of Engineer-in-Charge.

15mm (fifteen millimetre) nominal bore :-

Providing and fixing 15mm (fifteen millimetre) nominal boreChromium plated brass ISI marked IS No.8934 of JAL/ESS ESS make bib cock of approved quality including carriage of materials upto all leads and lifts also and as per the direction of Engineer-in-Charge.

Providing and fixing brass ISI marked IS No.8934 of JAL/ESS ESS stop cock of approved quality 15mm (fifteen millimetre) nominal bore including carriage of materials upto all leads and lifts also and as per the direction of Engineer-in-Charge.

Providing and fixing 15mm (fifteen millimetre) nominal boreC.P. brass ISI marked IS No.8934 of JAL/ESS ESS angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 including carriage of materials upto all leads and lifts also and as per the direction of Engineer-in-Charge.

Providing and fixing C.P. Brass extension nipple (size fifteen milimetre into fifty milimetre) of approved make and quality including carriage of materials upto all leads and lifts also and as per the direction of Engineer-in-Charge.

Providing and fixing 100 mm(one hundred milimetre) C.P grating for gully/ floor trap,including all leads,lifts and carriage of materials and other incidental charges complete as per entire satisfaction of the Engineer-in-charge.

Providing and fixing Single socketed pipeon under ground waste unplasticised Rigid PVC pipes conforming to IS : 13592 Type B of Supreme /Finolex make including jointing with seal ring conforming to IS : 5382, leaving 10 mm (ten milimetre)gap for thermal expansion, including all leads,lifts and carriage of materials and other incidental charges complete as per entire satisfaction of the Engineer-in-charge.

(i) (150 mm (One hundred fifty milimetre) diameter overall size having 2.7 mm (two point seven milimetre) thickness.

100 mm (One hundred milimetre) diameter overall size having 2.7 mm (two point seven milimetre) thickness.

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC waste pipes conforming to IS : 13592 Type B of Supreme /Finolex make , including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion including all leads,lifts and carriage of materials and other incidental charges complete as per entire satisfaction of the Engineer-in-charge.

150MM dia(one hundred fifty milimetre diameter)

110mm dia(one hundred ten milimetre diameter)

75mm dia(seventy five milimetre diameter)

Shoe (Plain)/Heal rest 110mm dia(One hundredten milimetre diameter)

75mm Dia(seventy five milimetre diameter)

(c)Coupler/Collar150mm dia(One hundred fifty milimetre diameter)

110mm dia(One hundredten milimetre diameter)

75mm Dia(seventy five milimetre diameter)

150X150X150mm (one hundred fifty into one hundred fifty into one hundred fifty milimetre).

110X110X110mm (one hundred ten into one hundred ten into one hundred ten milimetre).

75X75X75mm (seventy five into seventy five into seventy five milimetre).

150X150X150mm (one hundred fifty into one hundred fifty into one hundred fifty milimetre).

110X110X110mm (one hundred ten into one hundred ten into one hundred ten milimetre).

75X75X75mm (seventy five into seventy five into seventy five milimetre).

Providing and fixing single socketed pipe on wall face or underground waste unplasticised Rigid PVC pipes conforming to IS : 13592 Type B of Supreme /Finolex make including jointing with seal ring conforming to IS : 5382, leaving 10 mm (ten milimetre) gap for thermal expansion,including all leads,lifts and carriage of materials and other incidental charges complete as per entire satisfaction of the Engineer-in-charge.

110 mm (One hundred ten milimetre) diameter overall size having 2.7 mm (two point seven milimetre) thickness.

75mm (seventy five milimetre)diameter overall size having 2.7 mm(two point seven milimetre) thickness.

Providing and fixing C.P. Brass toilet paper holder ,including all leads,lifts and carriage of materials and other incidental charges complete as per entire satisfaction of the Engineer-in-charge.

Providing and fixing CP Brass 32mm (thirty two milimetre) size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge ,including all leads,lifts and carriage of materials and other incidental charges complete as per entire satisfaction of the Engineer-in-charge.

Providing and fixing PVC Cowl for ventilating pipes for rain water pipe or soil waiste pipe 110mm dia (One hundred ten Milimetre diametre). PVC Cowl of 2.7mm (Two point seven milimetre) thick. including all leads,lifts and carriage of materials and other incidental charges complete as per entire satisfaction of the Engineer-in-charge.

Providing and fixing15mm(Fifteen milimetre) nominal bore 45 cm(Forty five centimetre) in length uplasticised PVC connection pipe with brass union, including carriage of materials upto all leads and lifts also and as per the direction of Engineer-in-Charge.

Providing and fixing 25 mm(Twenty five milimetre) nominal bore gun metal gate valve with C.I. wheel of approved quality (screwed end) including carriage of materials upto all leads and lifts also and as per the direction of Engineer-in-Charge.

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) including carriage of materials upto all leads and lifts also and as per the direction of Engineer-in-Charge.

15 mm(Fifteen milimetre) nominal bore.

25mm(twenty five milimetre) nominal bore.

Providing and fixing in position 25 mm (twenty five milimetre)diameter mosquito proof coupling of approved municipal design ,including all leads,lifts and carriage of materials and other incidental charges complete as per entire satisfaction of the Engineer-in-charge.

Providing and fixing 600x450 mm (six hundred into four hundred fifty milimetre)beveled edge mirror ofsuperior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P.brass screws and washers complete,including all leads,lifts and carriage of materials and other incidental charges complete as per entire satisfaction of the Engineer-in-charge.

Providing and fixing 600x120x5 mm (six hundred into one hundred twenty five into five milimetre)glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm(forty milimetre) long screws, rawl plugs etc.,complete ,including all leads,lifts and carriage of materials and other incidental charges complete as per entire satisfaction of the Engineer-in-charge.

Providing and fixing P and S trap for water closet viterous china including all leads,lifts and carriage of materials and other incidental charges complete as per entire satisfaction of the Engineer-in-charge.

Providing and fixing G.I. inlet connection for flush pipe connecting with W.C.,including all leads,lifts and carriage of materials and other incidental charges complete as per entire satisfaction of the Engineer-in-charge.

Providing & fixing diversion plate 450x350 ( four hundred fifty into three hundredfifty ) milimeter size for urinal as per HP.PWD,. specification, including carriage of alllabour equipment & materials to various location through all modes of including

Providing and fixing PTMT Ball cock of approved quality, colour and make complete with Epoxy coated aluminium rod with L.P./ H.P.H.D. plastic ball. 25 mm(Twenty five milimetre) nominal bore, 152mm(One hundred fifty two milimetre) long, weighing not less than 440 gms(Four hundred forty gramme) including carriage of materials upto all leads and lifts also and as per the direction of Engineer-in-Charge.

Providing and fixing PTMT shelf 440 mm long, 124 mm width and 36 mm height of approved quality and colour, weighing not less than 300 gms including all leads,lifts and carriage of materials and other incidental charges complete as per entire satisfaction of the Engineer-in-charge.

Providing and fixing PTMT liquid soap container 109 mm (one hundred nine milimetre) wide, 125 mm (one hundre twenty five milimetre) high and 112 mm (one hundred twelve milimetre) distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms (one hundred five gramme) including all leads,lifts and carriage of materials and other incidental charges complete as per entire satisfaction of the Engineer-in-charge.

Providing and fixing PTMT towel ring trapezoidal shape 215 mm (two hundred fifteen milimetre) long, 200 mm(two hundred milimetre) wide with minimum distances of 37 mm(thirty seven milimetre) from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms(eighty eight gramme) including all leads,lifts and carriage of materials and other incidental charges complete as per entire satisfaction of the Engineer-in-charge.

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour.(i) 600 mm Six hundred milimetre) long towel rail with total length of 645 mm(six hundred forty five milimetre), width 78 mm(seventy eight milimetre) and effective height of 88 mm(eighty eight milimetre), weighing not less than 190 gms(one hundred ninety gramme) including all leads,lifts and carriage of materials and other incidental charges complete as per entire satisfaction of the Engineer-in-charge.

Providing, laying and jointing Half round glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (one cement : one fine sand) including testing of joints etc. complete 200 mm(two hundred milimetre) diameter including all leads,lifts and carriage of materials and other incidental charges complete as per entire satisfaction of the Engineer-in-charge.

Providing and laying cement concrete 1:5:10 (one cement : five coarse sand : ten graded stone aggregate 40 mm(forty milimetre) nominal size) all-round S.W. pipes including bed concrete as per standard design including all leads,lifts and carriage of materials and other incidental charges complete as per entire satisfaction of the Engineer-in-charge.(i)200 mm diameter S.W. pipe

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design(i)100x100 mm size P type.(i) With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 ,including all leads,lifts and carriage of materials and other incidental charges complete as per entire satisfaction of the Engineer-in-charge.

Cutting holes up to 30x30 cm (thirty into thirty centimetre) in walls including making good the same: With common burnt clay F.P.S. (non modular) bricks including all leads,lifts and carriage of materials and other incidental charges complete as per entire satisfaction of the Engineer-in-charge.

Cutting holes up to 15x15 cm (fifteen into fifteen centimetre) in R.C.C. floors and roofs for passing drain pipe etc.and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4(one cement : two coarse sand : four graded stone aggregate 20 mm(twenty milimetre) nominal size),including finishing complete so as to make it leak proof ,including all leads,lifts and carriage of materials and other incidental charges complete as per entire satisfaction of the Engineer-in-charge.

Providing and fixing 1.00 (one)horse power Water pump of Kirlosker make or its equivlent as per direction of Engineer-in-Charge to Lift rain water,including all leads,lifts and carriage of materials and other incidental charges complete as per entire satisfaction of the Engineer-in-charge.

Supplying and fixing Contral Panal for Pump complete with sheet and angle iron painted with internal wiring, airbreak starter , main switch of main switch, voltmeter, ammeter etc complete,including all leads,lifts and carriage of materials and other incidental charges complete as per entire satisfaction of the Engineer-in-charge.

Constructing brick masonry manhole in cement mortar 1:4 ( one cement : four coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (one cement : one point five coarse sand : three graded stone aggregate 20 mm(twenty milimetre) nominal size), foundation concrete 1:4:8 mix (one cement : four coarse sand : eight graded stone aggregate 40 mm (forty milimetre) nominal size), inside plastering 12 mm(twelve milimetre) thick with cement mortar 1:3 (one cement : three coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (one cement : two coarse sand : four graded stone aggregate 20 mm (twenty milimetre) nominal size) finished with a floating coat of neat cement complete as per standard design : (i)Inside size 90x80 cm(ninety into eighty centimetre) and 45 cm (forty five centimetre) deep including C.I. cover with frame (light duty) 455x610 mm (four hundred fifty five into six hundred ten milimetre) internal dimensions, total weight of cover and frame to be not less than 38 kg(thirty eight kilogramme) (weight of cover 23 kg(twenty three kilogramme) and weight of frame 15 kg( fifteen kilogramme)) : (i) With common burnt clay F.P.S. (non modular) bricks of class designation 7.5,including all leads,lifts and carriage of materials and other incidental charges complete as per entire satisfaction of the Engineer-in-charge.

Supplying and fixing cast iron cover without frame (Light duty single seal pattern -1(one)) 455x610 mm (four hundred fifty five into six hundre ten milimetre) internal dimensions total weight of cover without frame to be not less than 23 kg.(twenty three kilogramme)(Weight of cover23 kg.(twenty three kilogramme)), including all leads,lifts and carriage of materials and other incidental charges complete as per entire satisfaction of the Engineer-in-charge.

Cutting chases in brick masonry walls for following diameter sand cast iron/centrifugally cast (spun) iron pipes and making good the same with cement concrete 1:3:6 (one cement : three coarse sand :six graded stone aggregate 12.5 mm(twelve point five milimetre) nominal size), including necessary plaster and pointing in cement mortar 1:4 (one cement : four coarse sand) including all leads,lifts and carriage of materials and other incidental charges complete as per entire satisfaction of the Engineer-in-charge.

110mm dia(One hundredten milimetre diameter).

75mm Dia(seventy five milimetre diameter).

LOKINDER RAITKA