PROVISION OF DEFICIENT IN LIVING OFFICER ACCOMMODATION INCLUDING ADMIN AND ASSOCIATED MESS FACILITIES BY DEMOLITION OF EXISTING BUILDING AT WNC O MESS COLABA

Amount

Schedule-A' Part-I 'Buildings & Structures' Total of Schedule-'A' Part-I B/F from serial page No. 35

Schedule-A' Part-II(A) 'Excavation, Earthwork, Site Clearance and Land Development' Total of Schedule-'A' Part-II(B) B/F from serial page No. 36

Schedule-A' Part-II(B) 'Excavation, Earthwork, Site Clearance and Land Development' Total of Schedule-'A' Part-II(B) B/F from serial page No. 38

Schedule-A' Part-III 'Internal Water Supply' Total of Schedule-'A' Part-III B/F from serial page No. 40

Schedule-A' Part-IV 'Internal Electrification' Total of Schedule-'A' Part-IV B/F from serial page No. 46

Schedule-A' Part-V 'Lifts' Total of Schedule-'A' Part-V B/F from serial page No. 54

Schedule-A' Part-VI 'Air Conditioning' Total of Schedule-'A' Part-VI B/F from serial page No. 56

Schedule-A' Part-VII 'Fire Fighting System' Total of Schedule-'A' Part-VII B/F from serial page No. 64

Schedule-A' Part-VIII 'Lightning Protection' Total of Schedule-'A' Part-VIII B/F from serial page No. 66

Schedule-A' Part-IX 'Cable TV & Telephone Wiring & Conduiting' Total of Schedule-'A' Part-IX B/F from serial page No. 67

Schedule-A' Part-X 'Standby Power Supply (DG Set)' Total of Schedule-'A' Part-X B/F from serial page No. 69

Schedule-A' Part-XI 'Additonal Power Points' Total of Schedule-'A' Part-XI B/F from serial page No. 71

Schedule-A' Part-XII 'Solar Water Heating System' Total of Schedule-'A' Part-XII B/F from serial page No. 73

Schedule-A' Part-XIII 'Refrigerators & Water Coolers' Total of Schedule-'A' Part-XIII B/F from serial page No. 74

Schedule-A' Part-XIV 'Roads / Paths / Hard Standing' Total of Schedule-'A' Part-XIV B/F from serial page No. 76

Schedule-A' Part-XV 'Sewage Disposal' Total of Schedule-'A' Part-XV B/F from serial page No. 78

Schedule-A' Part-XVI 'Area Drainage' Total of Schedule-'A' Part-XVI B/F from serial page No. 79

Schedule-A' Part-XVII 'External Water Supply' Total of Schedule-'A' Part-XVII B/F from serial page No. 82

Schedule-A' Part-XVIII 'External Electrification' Total of Schedule-'A' Part-XVIII B/F from serial page No. 87

Schedule-A' Part-XIX 'Rain Water Harvesting' Total of Schedule-'A' Part-XIX B/F from serial page No. 89

Schedule-A' Part-XX 'Demolition & Dismantling' Total of Schedule-'A' Part-XX B/F from serial page No. 92

Schedule-A' Part-XXI 'PRIME COST SUM' as " fountain for aeration and POP ceilings and borders" Note 1. The work under PRIME COST SUM shall be measured and paid as per condition 5 of IAFW 2249 (General conditions of Contracts) 2. This percentage (plus/minus) sunject to maximum of 15% (on plus side) shall be taken as the PC sum percentage

PART-XXII (Miscelleneous Items)

Internal Water Supply

S&F angular stop cock 15mm dia quarter turn adjustable wall flange of approved finish complete all as specified and as directed Make: Jaquar Model No. CQT-23059 GD or equivalent model of Crab Tree / Kohler

S&F two way bib cock 15mm dia of approved finish complete all as specified and as directed Make: Jaquar Model No. CQT-23041 GD or equivalent model of (Flow rate 4.0LPM) Crab Tree / Kohler

S&F bib cock 15mm dia, fancy type, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and as directed Make: Jaquar Model No. CQT-23047 GD or equivalent model of (Flow rate 4.0LPM) Crab Tree / Kohler Note: This item shall be operated for solar water heating system as required

S&F chromium plated push cock for urinal 15mm dia complete all as specified and as directed Make: Jaquar Model No. PRS-073 or equivalent model of (Flow rate 1.5LPM)Crab Tree / Kohler

S&F health faucet with flexible pipe (ABS body) with 1.0m long PVC tube and wall hook of approved finish complete all as specified and as directed Make: Jaquar Model No. ALD-CHR-583 GA or (Flow rate 4LPM) equivalent model of Crab Tree / Kohler

S&F 20mm dia sink cock with swinging casted round shaped spout (wall mounted type), quarter turn of approved finish complete all as specified and as directed Make: Jaquar Model No. CQT-23347 GD or equivalent model of (Flow rate 4.0LPM) Crab Tree / Kohler

S&F concealed stop cock 25mm dia regular body with adjustable wall flange, of approved finish complete all as specified and as directed Make: Jaquar Model No. CQT-23089 or equivalent model of Crab Tree / Kohler

S&F PVC connections 600mm long with braided hose with M10X1 nipple, 15mm nut, O ring and rubber washer complete all as specified and as directed Make: Jaquar Model No. ALD-803AB or equivalent model of Crab Tree / Kohler

S&F overhead shower 80mm dia, round shape, single flow (ABS body chromium plated with face plate), with shower arm 15mm size with 45o bend complete all as specified and as directed Make: Jaquar Model No. OHS-1985 GA or equivalent model of (Flow rate 6.0LPM) Crab Tree / Kohler

S&F wall mixer with provision of overhead shower with 115mm long bend pipe on upper side, connecting legs and wall flanges of approved finish complete all as specified and as directed Make: Jaquar Model No. CQT-23281UPR GD or equivalent model of (Flow rate 4LPM) Crab Tree / Kohler Note: Overhead shower shall be measured and paid separately under respective item

S&F brass forged pressure reducing valves complete all as specified and as directed for the following sizes: Make: Zoloto / Prayag / Seico / Leader / Neeta

(a) 32mm dia

(b) 40mm dia

(c) 50mm dia

(d) 65mm dia

(e) 80mm dia

S & F Table top Wash hand Basin of size 485 X 395 X 150mm. Fixed on /into 17-20mm thick Granite Platform of size extended at three sides (except wall side) 150 mm from outer most edge of wash basin including all accesories such as waste coupling, Bottle trap etc complete all as specified and directed by Eng in charge. Make: Jaquar , Product Code - JDS - WHT- 25909 or Equivalent in Crab Tree/Kohler Brand

S&F Pillar taps Fancy type chromium plated 15mm, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed by Eng in charge. Make: Jaquar Model No 23127 GD or equivalent in Crab Tree/Kohler brand.

S & F Swivel Towel Holder twin type complete all as specified and directed by Eng-in-charge. Make: Jaquar, Cat No. CAN-CHR- 1115S or Equivalent in Crab Tree/Kohler Brand

S & F soap dispenser with metallic Bottle complete all as specified and directed by Eng-in-charge. Make: Jaquar, Cat No. CAN-CHR-1137N or Equivalent in Crab Tree/Kohler Brand

S & F frameless Corner entry shower enclosure with fixed glass of thickness 8-10mm, chrome finished door of size- H-1950mm, W-1600-2000mm complete all as specified and directed by Eng in charge. Make: Jaquar , Cat No. JSE-CHR-40P1620 H 19X or Equivalent in Crab Tree/Kohler Brand

S & F thermostatic concealed high flow control valve with wall flange complete all as specified and directed by Eng in charge. Make: Jaquar, Cat No. FLR- CHR- 5679 or equivalent in Crab Tree/Kohler Brand

S & F 4 way diverter (consisting of concealed body & wall flange) for multiple shower working with one shut off position & 3 outlets in round handle (recommended for use with Item FLR-5679) Product Code- ALD- CHR- 287 R Vcomplete all as specified and directed by Eng in charge. Make: Jaquar or equivalent in Crab Tree/Kohler Brand

S & F stainless steel round shape over head 300mm shower complete all as specified and directed by Eng in charge. Make: Jaquar, Cat No - OHS-CHR-1633 or Equivalent in Crab Tree/Kohler Brand

S & F hand shower dia 120mm multi flow with cascade effect & rubit cleaning system complete all as specified and directed by Eng in charge. Make: Jaquar, Cat No- HSH- CHR- 1731 or equivalent in Crab Tree/Kohler Brand

S & F easy flex tube in chrome finish 1.5m long with nuts complete all as specified and directed by Eng in charge. Make: Jaquar, Cat No. SHA-CHR-571, or equivalent in Crab Tree/Kohler Brand

S & F Towel rack with Long hanger complete all as specified and directed by Eng in charge. Make: Jaquar, Cat No. AHS - 1581 or equivalent in Crab Tree/Kohler Brand

S & F ceramic wall hung designer water closet with seat cover size - 365 X365X 545mm complete all as specified and directed by Eng in charge. Make: Jaquar, Cat No. FLS-WST-5951 or equivalent in Crab Tree/Kohler Brand

S & F Toilet paper holder with flap recessed type (stainless steel) complete all as specified and directed by Eng in charge. Make: Jaquar, Cat No. AHS- CHR-1553 or equivalent in Crab Tree/Kohler Brand

S & F soap dish holder complete all as specified and directed by Eng in charge. Make: Jaquar, Cat No. CAN- CHR- 1131N or equivalent in Crab Tree/Kohler Brand

S & F Towel rail 300mm long stainless steel for WHB complete all as specified and directed by Eng in charge. Make: Jaquar, Cat No. CAN-CHR- 1101N or equivalent in Crab Tree/Kohler Brand

S & F single lever basin mixers with 450mm long braided hose complete all as specified and directed by Eng in charge. Make: Jaquar, Cat No. 5001B-GD or equivalent in Crab Tree/Kohler Brand

S & F Urinals (top inlet) of size 330X345X610mm Make: Jaquar, Cat No. URS -WHT- 13257 or equivalent complete including providing and fixing plugs, beeding urinal againgst wall in CM 1:2 securing urinals to plugs with and including 60mm long brass screws, pointing around urinal bed in cement including PVC west pipe etc. complete all as directed by Engineer-in-charge

S & F swivel looking mirror complete all as specified and directed by Eng in charge. Make: Jaquar, Cat No. CAN-CHR-1131N or equivalent in Crab Tree/Kohler Brand

S & F sensor sensotronic mini concealed flushing cistern complete all as specified and directed by Eng in charge. Make: Jaquar, Cat no- SNR-STL-51083-G or equivalent in Crab Tree/Kohler Brand

S & F metro pole flush valve dual flow 32mm size (concealed body) with concealed shutt off provision & rectangular dual flush plate , ABS chrome plated complete all as specified and directed by Eng in charge. Make: Jaquar, Cat No. 1085DFP-G or equivalent in Crab Tree/Kohler Brand

S & F single piece WC, trap distance - S-300 complete all as specified and directed by Eng in charge. Make: Jaquar, Cat No. VGS-WHT-0207 or equivalent in Crab Tree/Kohler Brand

S & F bevelled edge looking mirror 5.50mm to 6.0mm thick covering of size 800x800mm mounted on 6mm thick plywood backing complete all as directed by Engineer-in-charge

Supply and installation of centrifugal pump viable for 100 LPM at 60m load etc complete all as specified and as directed.

Internal Electrification

S&F modular type bell ding dong of 2 module size, conforming to IS: 8884-1978 complete all as specified and as directed Make: Legrand 'Arteor' Cat-Part No. 5734 43 or equivalent model in Havells / Anchor

S&F 63A panel mounted (3P+N+E) angled socket, conforming to IEC 60309-1 & 60309-2, having IP-67 ingress protection & IK-08 impact protection suitable for 415V, 50Hz electric supply complete all as specified and as directed Make: Schneider Pratika Cat-Part No. 81283 or equivalent model in Legrand / Havells

S&F 10W surface/wall mounted LED batten including LED having high efficiency long life LED chips with luminous efficacy of > 100 lumen/W, independent isolated SMPS based constant current electronic LED driver with THD < 20%, surge voltage protection and other safety tests as per IS: 15885 (Part-2/Sec-13): 2012, polycarbonate diffuser, housed in powder coated white extruded aluminium channel housing and white coloured ABS end caps having input voltage 220- 240V, input frequency 50- 60Hz, PF>0.95, including electrical connection with 3 core flexible copper conductor cable of appropriate size from ceiling rose to the fixture complete all as specified and as directed Make: Bajaj Cat-Part No. 112407 BCLSB 10WH or equivalent model in Havells / Philips / Wipro

S&F 20W surface/wall mounted LED batten including LED having high efficiency long life LED chips with luminous efficacy of > 100 lumen/W, independent isolated SMPS based constant current electronic LED driver with THD < 20%, surge voltage protection and other safety tests as per IS: 15885 (Part-2/Sec-13): 2012, polycarbonate diffuser, housed in powder coated white extruded aluminium channel housing and white coloured ABS end caps having input voltage 220- 240V, input frequency 50- 60Hz, PF>0.95, including electrical connection with 3 core flexible copper conductor cable of appropriate size from ceiling rose to the fixture complete all as specified and as directed Make: Bajaj Cat-Part No. 112785 BCLAB 20W or equivalent model in Havells / Philips / Wipro

S&F 2x20W surface/wall mounted LED batten including LED having complete internal wiring suitable for retrofit LED tube light with double side connections, powder coated CRCA sheet steel housing, white powder coated CRCA sheet reflector, push-fit type white polycarbonate lamp holders with corrosion resistant brass contacts having input voltage 220- 240V, input frequency 50- 60Hz, PF>0.95, along with 20 W LED polycarbonate tube light having high efficiency long life SMD LED module with luminous efficacy of > 100 lumen/W, integral SMPS based constant current electronic LED driver with THD < 20%, surge voltage protection and other safety tests as per IS: 15885 (Part-2/Sec-13): 2012, high quality polycarbonate end caps and polycarbonate housing in opal finish including electrical connection with 3 core flexible copper conductor cable of appropriate size from ceiling rose to the fixture complete all as specified and as directed Make: Bajaj Cat-Part No. 112688 BJI 218 LED PC & 112481 BRLB 21W CWC or equivalent model in Havells / Philips / Wipro

S&F 12W recessed mounted round shape LED downlight including LED having long life SMD LED mounted on MCPCB with high LED efficacy of > 85 lumen/W, high quality polycarbonate opal concave diffuser, high reflective polycarbonate conical shaped reflector, integral SPMS based constant current electronic LED driver with THD<20%, surge voltage protection and other safety tests as per IS: 15885 (Part-2/Sec-13): 2012, housed in white powder coated pressure die-cast aluminium heat sink and white finish polycarbonate ring for holding the diffuser having input voltage 220- 240V, input frequency 50- 60Hz, PF>0.95, including electrical connection with 3 core flexible copper conductor cable of appropriate size from ceiling rose to the fixture complete all as specified and as directed Make: Bajaj Cat-Part No. 112671 BPSLR 12W WH or equivalent model in Havells / Philips / Wipro

S&F 43W recessed mounted square shape 2'x2' LED panel including LED having high efficiency long life LED package in integral module with luminous efficacy of > 100 lumen/W, independent isolated SMPS based constant current electronic LED driver with THD<20%, surge voltage protection and other safety tests as per IS: 15885 (Part-2/Sec-13): 2012, high transmittance polystyrene opal diffuser, housed in white powder coated pressure die-cast aluminium heat sink having input voltage 220- 240V, input frequency 50- 60Hz, PF>0.95, including electrical connection with 3 core flexible copper conductor cable of appropriate size from ceiling rose to the fixture complete all as specified and as directed Make: Bajaj Cat-Part No. 112669 BZRSQL 43W GZ1 NW or equivalent model in Havells / Philips / Wipro

S&F 45W LED street light including LED having high efficiency long life LED module with SMD LED package mounted on MCPCB with high LED efficacy of ≥ 100 lumen/W, integral SMPS based constant current electronic LED driver with THD<20%, surge voltage protection and other safety tests as per IS: 15885 (Part-2/Sec-13): 2012, IP 66 protection, high effiency polycarbonate cover with integrated lens housed in pressure die-cast aluminium alloy heat sink for effective thermal management, sturdiness, excellent corrosion resistance, separate optical and control gear compartment & top opening for easy maintenance, suitable for side entry, pole mounting with bracket arm OD 35mm to 42mm including necessary electrical connection to the fixture with 3 core flexible copper conductor cable of appropriate size and 1.5m long bracket, having 40mm diameter light grade GI pipe, including GI clamps, nuts, bolts & washers with two coats of synthetic enemal paint over a coat of red oxide primer complete all as specified and as directed

Make: Bajaj Cat-Part No. BAJAJ 169799 BRTFG 45W LED I or equivalent model in Philips / Wipro

S&F 9W LED bollard fittings including LED having high efficiency long life LED module with SMD LED package mounted mounted on MCPCB, luminous efficacy ≥ 100 lumen/W, integral SMPS based constant current electronic LED driver with THD<20%, surge voltage protection and other safety tests as per IS: 15885 (Part-2/Sec-13): 2012, IP 66 protection, housed in powder coated aluminium pipe with aluminium heat sink for effective thermal management, sturdiness & excellent corrosion resistance and mounting flange of MS sand casting at the bottom, mounted by means of 3Nos. M10 bolts, including electrical connection with 3 core flexible copper conductor cable of appropriate size complete all as specified and as directed Make: Bajaj Cat-Part No. BAJAJ 111284 BGBOM 650 9W LED or equivalent model in Havells / Philips / Wipro

S&F 10W wall/ceiling mounted LED bulk head fittings including LED having high efficiency long life LED module with SMD LED package mounted on MCPCB, luminous efficacy ≥ 100 lumen/W, integral SMPS based constant current electronic LED driver with THD<20%, surge voltage protection and other safety tests as per IS: 15885 (Part-2/Sec-13): 2012, high quality powder coated polycarbonate diffuser in opal finish cover housed in oval shaped pressure die-cast aluminium housing & ring for sturdiness & corrosion resistance, mounted by means of CRCA lamp with expansion screws provided through 5.3mm dia mounting holes including LED bulb, electrical connection with 3 core flexible copper conductor cable of appropriate size complete all as specified and as directed Make: Bajaj Cat-Part No. 112334 BIBWP 10W LED or equivalent model in Havells / Philips / Wipro

S&F BEE five star rated energy efficient high-speed ceiling fan having 1200mm blade sweep, air-flow not less than 210CMM, operating voltage 220-240V and frequency 50Hz, including a downroad of suitable size and electrical connection with 3 core flexible copper conductor cable of appropriate size from ceiling rose to the fan complete all as specified and as directed Make: Crompton Cat-Part No. ENTRUST50 or Havells Cat- Part No. ES-50 or equivalent model in Usha / Bajaj

S&F engery efficient non-metalic fresh air fan having blade sweep 250mm, air delivery not less than 860CMH, operating voltage 220-240V and frequency 50Hz, including electrical connection with 3 core flexible copper conductor cable of appropriate size from ceiling rose to the fresh-air fan complete all as specified and as directed Make: Crompton Cat-Part No. VENTILUS 10" or equivalent model in Usha / Havells / Bajaj

S&F engery efficient metalic exhaust fan having blade sweep 450mm, air delivery not less than 6000CMH, operating voltage 220-240V and frequency 50Hz, including electrical connection with 3 core flexible copper conductor cable of appropriate size from ceiling rose to the fresh-air fan complete all as specified and as directed Make: Crompton Cat-Part No. EXHD450-4-1 or equivalent model in Usha / Havells / Bajaj

Supply, installation, testing and commissioning of 3200A sandwitch type silver flashed, bi-metal copper contact, aluminium busway (3L+N+PE), with original Mylar insulation from Dupont, 100% neutral, 100kA for 1second, 50% integral earth, dual housing complete all as specified and as directed Make: Schneider, ABB, Siemens

The busbar trunking system shall conform to the following technical specifications: [A] General: [i] The busbar trunking system (BTS), both feeder and plug-in, shall be of sandwich construction. All components and fittings (straight length, elbow, tees, flanged ends, cable tap box and circuit breaker, etc.) shall be in accordance with IEC 61439 Part 6 (2012) or UL857 and from the same manufacturer as the busbar trunking system. Degree of protection of the BTS shall be IP 54 in accordance with IEC 60529 [ii] Rated operation voltage of the BTS shall be 1kV. The neutral conductor shall have the same cross-sectional area as the phase conductor. The earth busbar must be one continuous piece without bolting on housing

[B] Certificate: [i] The busbar, of full range and each rating, shall pass full type tests specified in IEC 61439-6. The certificate shall be issued by an international independent testing authority (e.g. ASTA, KEMA, UL) [ii] A product safety mark (e.g. KEMA-KEUR, ASTA DIAMOND, UL) shall be on the product offering a visible assurance to all of full product safety testing, factory inspection and ongoing surveillance under independent authority to ensure the ongoing safety of product [iii] The BTS shall pass seismic tests with actual physical product and being certified complying with UBC seismic zone 4 condition by an international recognized earthquake research body, e.g. Asia Pacific Network of Centers for Earthquake Engineering Research (ANCER)

[C] Short-Circuit Ratings & Tests: [i] The whole BTS shall be capable of withstanding the short circuit of the electrical installation without undergoing any electrical, mechanical and thermal stress under fault condition at a service voltage of 1kV at 50Hz frequency. The minimum rated insulation voltage shall be 1kV [ii] Minimum certified short circuit ratings shall be 198kA peak and 90kA for 1s for 3200A BTS

[D] Housing: [i] The busbar trunking housing shall be constructed of electro galvanized steel and aluminum to reduce hysteresis and eddy current loses and shall be provided with a suitable protective finish of ANSI 49 grey epoxy paint [ii] The busbar trunking housing shall be totally enclosed non-ventilated for protection against mechanical damage and dust accumulation. And it shall pass at least 2000hr salt spray test to ensure the anticorrosion ability [iii] The totally enclosed housing shall be manufactured by the busbar trunking manufacturer. Modifications of busbar trunking to make it totally enclosed by housing other than the busbar trunking manufacturer voids the manufacturer’s warranty. Busbar trunking so modified is unacceptable without the written consent of the manufacturer

[E] Busbars: [i] Busbars shall be of aluminum with copper cladding utilized Molecular Fusion technology [ii] There shall be no bolts passing through the busbars of the busway [iii] Each busbar shall be insulated with Class B (130℃) DuPont Mylar insulation. Epoxy insulation is unacceptable [iv] The temperature rise at any point of the busbar trunking enclosure shall not exceed 55°C above the ambient temperature of 40°C when operated at rated current

[F] Joints: [i] The busbar trunking joint shall be of the one-bolt type which utilizes a high strength steel bolt(s) and Belleville washers to maintain proper pressure over a large contact surface area [ii] The bolt shall be torque indicating and at earth potential [iii] The bolt shall be two-headed design to indicate when proper torque has been applied and require only a standard long handle wrench to be properly activated [iv] Access shall be required to only one side of the busbar trunking for tightening joint bolts [v] It shall be possible to remove any joint connection assembly to allow electrical isolation or physical removal of a busbar trunking length without disturbing adjacent busbar trunking lengths

[G] Plug-in openings: [i] The connecting jaw of the plug-in unit shall plug directly on to the busbar and have full contact with busbar itself. Welded tab at plug-in busbar is unacceptable [ii] All contact on joint and plug-in opening should be silver plated copper [iii] On plug-in busbar trunking there shall be three dead front, hinged coveF80:F82r type plug-in openings on each side [iv] All openings shall be usable simultaneously [v] Busbar trunking shall be installed so that plugs are side mounted to permit practical use of all plug-in openings [vi] It shall be possible to inspect the plug-in opening and busbars prior to the installation of the plug-in units

[H] Plug-in units: [i] The plug-in jaw shall be spring design composed of different metal to ensure the firm and tight contact with the busbar [ii] Plug-in Units shall be type tested in accordance with IEC 61439-6 (Annex D: Part 1-5 and 9-13) [iii] The earthing contact of the plug-in unit shall always be made before that of the live conductors and the last to break during removal and it must connect to the earth bar of busway to ensure the safety [iv] Covers of all plug-in units must have interlocks to prevent the cover from being opened when the switch is in the ON position [v] Plug-in units (circuit breaker type or fusible switch type) shall be operated with visible blade quick-make and quick-break mechanism [vi] Presence of transparent shield shall be inside to avoid direct contact of human

[vii] The plug-in units shall be equipped with internal barriers to prevent accidental contact of fish tape and conductors with live parts on the line side of the protective device during time of wire pulling [I] Supporting structure: Indoor feeder and plug-in busbar trunking shall be approved for hanger spacing of up to 3m for horizontally mounted run and 4.88m for vertically mounted runs. Outdoor feeder busbar trunking shall be approved for spacing of up to 1.5m for horizontally or vertically mounted runs [J] Voltage drop: [i] The 3-phase line to line voltage drop 40% power factor concentrated loadshall not exceed 3.4V / 100feet [ii] The line-to line voltage drop at the load power factor shall not exceed 4.1V / 100feet

Straight riser length

90° elbow

Flange end

Adopter box

Support bracket/hangers for horizontal installation

Spring hangers for vertical installation

End cover

Tap-off units with FP MCCB (up to 100A)

Tap-off units with 125A FP MCCB

Tap-off units with 200A FP MCCB

Tap-off units with 400A FP MCCB

Tap-off units with 500A FP MCCB

Supply, installation, commissioning and testing of factory made, CPRI approved, indoor, cubical compartmental type 'Fourth Floor Panel', conforming to IEC 61439- 1 & 2, having both sides openable with hinged double doors & locking arrangement and IP-42 protection made out of 2mm thick mild steel CRCA sheet, supported and fixed on structural frame of angle iron, including earthing stud, labeling, painting to all internal & external exposed steel surfaces with powder coating paint (7 tank process), duly fixed on wall/floor with danger notice plate of 1.6mm thick mild steel sheet, vitreous enameled (white) with letters figures and conventional skull and bones in signal red colour, suitable for 3-Phase 4 Wire system, 500V grade with necessary wiring, PVC sheathed stranded copper conductor of appropriate length & size, including fixing lugs, bolts, screws, etc. complete all as specified and as directed Make: Schneider- Blokset, Siemens- Sivacon, ABB- MNS

The fourth floor panel shall comprise of the following: [a] Busbar Chamber: [i] Copper busbar of rated capacity 500A, covered with PVC insulated sleeves including insulator, nuts, bolts, etc. with complete connection- 01 Set (3P+N) [b] Incoming: [i] 400A, 415V, Ics = Icu = 36kA, 50Hz, FP MCCB with adjustable overload settings (0.36- 1 x In) & tr = 0.5 - 16 s, adjustable short-circuit settings (1.5 - 10 x Ir), adjustable earth- fault settings (0.2- 1 x In), current limiting type double break roto active type, instanteneous protection and microprocessor based trip unit- 01No. [ii] LED phase indicators (Red, Yellow, Blue)- 01set [iii] Power Measurement Device with Class 1 accuracy, complying to IEC 62053- 22, 64 samples/cycle, 31st harmonic analysis, RS485, calibration LED, third party accuracy test certificate- 01No.

[c] Outgoing: [i] 320A, 415V, Ics = Icu = 36kA, 50 Hz, FP MCCB with adjustable overload settings (0.36- 1 x In) & tr = 0.5 - 16 s, adjustable short-circuit settings (1.5 - 10 x Ir), adjustable earth- fault settings (0.2-1 x In), current limiting type double break roto active type, instanteneous protection and microprocessor based trip unit- 01No. [ii] 63A, 10kA, 415V, 50Hz FP MCB (c -curve)- 1No. [iii] 32A, 10kA, 415V, 50Hz FP MCB (c -curve)- 2Nos. [iv] LED phase indicators (Red, Yellow, Blue)- 01set [v] Cl 1.0 multi-function meter capable of measuring V, A, F, PF, W/VA, Wh/VAh, Run hours. On hours & interupts- 01No. Note: [i] The panel shall be completely Ethernet communication ready to communicate with Energy Management System & shall be web based application in-built [ii] 02Nos. of ON/OFF/trip status and operations counters as well as multi-function meters shall be wired to Ethernet Gateway part of the panel

Supply, installation, commissioning and testing of factory made, CPRI approved, indoor, cubical compartmental type 'Kitchen Equipment Panel', conforming to IEC 61439-1&2, having both sides openable with hinged double doors & locking arrangement and IP-42 protection made out of 2mm thick mild steel CRCA sheet, supported and fixed on structural frame of angle iron, including earthing stud, labeling, painting to all internal & external exposed steel surfaces with powder coating paint (7 tank process), duly fixed on wall/floor with danger notice plate of 1.6 mm thick mild steel sheet, vitreous enameled (white) with letters figures and conventional skull and bones in signal red colour, suitable for 3- Phase 4 wire system, 500V grade with necessary wiring, PVC sheathed stranded copper conductor of appropriate length & size, including fixing lugs, bolts, screws, etc. complete all as specified and as directed Make: Schneider- Blokset, Siemens- Sivacon, ABB- MNS

The kitchen equipment panel shall comprise of the following: [a] Busbar chamber: [i] Copper busbar of rated capacity 630A, covered with PVC insulated sleeves including insulator, nuts, bolts, etc. with complete connection- 01Set (3P+N)

[b] Incoming: [i] 500A, 415V, Ics = Icu = 36kA, 50 Hz, FP MCCB with adjustable overload settings (0.36- 1x In) & tr = 0.5-16s, adjustable short-circuit settings (1.5 - 10x Ir), adjustable earth- fault settings (0.2- 1 x In), current limiting type double break roto active type, instanteneous protection and microprocessor based trip unit- 01Nos. [ii] LED phase indicators (Red, Yellow, Blue)- 01Set [iii] Power Measurement Device with Class 1 accuracy, complying to IEC 62053- 22, 64 samples/cycle, 31st harmonic analysis, RS485, calibration LED, third party accuracy test certificate- 01Nos.

[c] Outgoing: [i] 400A, 415V, Ics = Icu = 36kA, 50Hz, FP MCCB with adjustable overload settings (0.36- 1 X In) & tr = 0.5 - 16s, adjustable short-circuit settings (1.5 - 10 x Ir), adjustable earth- fault settings (0.2- 1 x In), current limiting type double break roto active type, instanteneous protection and microprocessor based trip unit- 01No. [ii] 160A, 415 V, Ics = Icu = 25kA, 50Hz, FP MCCB with adjustable overload settings (0.36- x In) & tr = 0.5-16s, adjustable short-circuit settings (1.5 - 10 x Ir), adjustable earth- fault settings (0.2- 1 x In), current limiting type double break roto active type, instanteneous protection and microprocessor based trip unit- 01No.

[iii] 125A, 415V, Ics = Icu = 25kA, 50Hz, FP MCCB with adjustable overload settings (0.36- `X In) & tr = 0.5-16s, adjustable short-circuit settings (1.5 - 10 X Ir), adjustable earth- fault settings (0.2- 1 X In), current limiting type double break roto active type, instanteneous protection and microprocessor based trip unit- 01No. [iv] LED phase indicators (Red, Yellow, Blue)- 03 Set [v] Cl 1.0 multi-function meter capable of measuring V, A, F, PF, W/VA, Wh/VAh, Runhrs. Onhrs & interupts- 03Nos. Notes: [i] The panel shall be completely Ethernet communication ready to communicate with Energy Management System & shall be Web based application in-built [ii] 04Nos. of ON/OFF/trip status and operations counters as well as multi-function meters shall be wired to Ethernet Gateway part of the panel

Supply, installation, commissioning and testing of factory made, CPRI approved, indoor, cubical compartmental type 'Machine Socket Panel', conforming to IEC 61439- 1 & 2, having both sides openable with hinged double doors & locking arrangement and IP-42 protection made out of 2mm thick mild steel CRCA sheet, supported and fixed on structural frame of angle iron, including earthing stud, labeling, painting to all internal & external exposed steel surfaces with powder coating paint (7 tank process), duly fixed on wall/floor with danger notice plate of 1.6mm thick mild steel sheet, vitreous enameled (white) with letters figures and conventional skull and bones in signal red colour, suitable for 3 Phase 4 Wire system, 500V grade with necessary wiring, PVC sheathed stranded copper conductor of appropriate length & size, including fixing lugs, bolts, screws, etc. complete all as specified and as directed Make: Schneider- Blokset, Siemens- Sivacon, ABB- MNS

The Machine Socket Panel shall comprise of the following: [a] Busbar Chamber: [i] Copper busbar of rated capacity 500A, covered with PVC insulated sleeves including insulator, nuts, bolts, etc. with complete connection- 01Set (3P+N) [b] Incoming: [i] 400A, 415V, Ics = Icu = 36kA, 50Hz, FP MCCB with adjustable overload settings (0.36- 1 X In) & tr = 0.5 - 16s, adjustable short-circuit settings (1.5 - 10 X Ir), adjustable earth- fault settings (0.2- 1 X In), current limiting type double break roto active type, instanteneous protection and microprocessor based trip unit- 01No. [ii] LED phase indicators (Red, Yellow, Blue)- 01Set [iii] Cl 1.0 multi-function meter capable of measuring V, A, F, PF, W/VA, Wh/VAh, Runhrs. Onhrs & interupts- 01No. [c] Outgoing: [i] 40A, 10kA, 415V, 50Hz FP MCB (c -curve)- 10Nos.

Notes: [i] The panel shall be completely Ethernet communication ready to communicate with Energy Management System & shall be Web based application in-built [ii] 04Nos. of ON/OFF/trip status and operations counters as well as multi-function meters shall be wired to Ethernet Gateway part of the panel

Supply, installation, commissioning and testing of factory made, CPRI approved, indoor, cubical compartmental type 'Oven Socket Panel', conforming to IEC 61439- 1 & 2, having both sides openable with hinged double doors & locking arrangement and IP 42 protection made out of 2mm thick mild steel CRCA sheet, supported and fixed on structural frame of angle iron, including earthing stud, labeling, painting to all internal & external exposed steel surfaces with powder coating paint (7 tank process), duly fixed on wall/floor with danger notice plate of 1.6mm thick mild steel sheet, vitreous enameled (white) with letters figures and conventional skull and bones in signal red colour, suitable for 3 Phase 4 Wire system, 500V grade with necessary wiring, PVC sheathed stranded copper conductor of appropriate length & size, including fixing lugs, bolts, screws etc. complete all as specified as and as directed Make: Schneider- Blokset, Siemens- Sivacon, ABB- MNS

The Oven Socket Panel shall comprise of the following: [a] Busbar Chamber: [i] Copper busbar of rated capacity 200A, covered with PVC insulated sleeves including insulator, nuts, bolts, etc. with complete connection- 01Set (3P+N) [b] Incoming: [i] 160A, 415V, Ics = Icu = 25 kA, 50Hz, FP MCCB with adjustable overload settings (0.36- ` X In) & tr = 0.5 - 16s, adjustable short-circuit settings (1.5-10 X Ir), adjustable earth- fault settings (0.2-1 X In), current limiting type double break roto active type, instanteneous protection and microprocessor based trip unit- 01No. [ii] LED phase indicators (Red, Yellow, Blue)- 01 Set [iii] Cl 1.0 multi-function meter capable of measuring V, A, F, PF, W/VA, Wh/VAh, Runhrs. Onhrs & interupts- 01No. [c] Outgoing: [i] 63A, 10kA, 415V, 50Hz FP MCB (C-curve)- 03Nos.

Notes: [i] The panel shall be completely Ethernet communication ready to communicate with Energy Management System & shall be Web based application in-built. [ii] 01No. of ON/OFF/trip status and operations counters as well as multi-function meters shall be wired to Ethernet Gateway part of the Panel.

Supply, installation, commissioning and testing of factory made, CPRI approved, indoor, cubical compartmental type "Fifth Floor Panel", conforming to IEC 61439- 1 & 2, having both sides openable with hinged double doors & locking arrangement and IP 42 protection made out of 2mm thick mild steel CRCA sheet, supported and fixed on structural frame of angle iron, including earthing stud, labeling, painting to all internal & external exposed steel surfaces with powder coating paint (7 tank process), duly fixed on wall/floor with danger notice plate of 1.6mm thick mild steel sheet, vitreous enameled (white) with letters figures and conventional skull and bones in signal red colour, suitable for 3 Phase 4 Wire system, 500V grade with necessary wiring, PVC sheathed stranded copper conductor of appropriate length & size, including fixing lugs, bolts, screws etc. complete all as specified and as directed Make: Schneider- Blokset, Siemens- Sivacon, ABB- MNS

The Fifth Floor Panel shall comprise of the following: [a] Busbar Chamber: [i] Copper busbar of rated capacity 200A, covered with PVC insulated sleeves including insulator, nuts, bolts, etc. with complete connection- 01Set (3P+N) [b] Incoming: [i] 125 A, 415 V, Ics = Icu = 25 kA, 50Hz, FP MCCB with adjustable overload settings (0.36- ` X In) & tr = 0.5-16s, adjustable short-circuit settings (1.5-10 X Ir), adjustable earth- fault settings (0.2-1 X In), current limiting type double break roto active type, instanteneous protection and microprocessor based trip unit- 01No. [ii] LED phase indicators (Red, Yellow, Blue)- 01Set [iii] Cl 1.0 multi-function meter capable of measuring V, A, F, PF, W/VA, Wh/VAh, Runhrs. Onhrs & interupts- 01 Nos. [c] Outgoing: [i] 63A, 10kA, 415V, 50Hz FP MCB (C-curve)- 01No.

[ii] 40A, 10kA, 415V, 50Hz FP MCB (C-curve)- 02Nos. [iii] 32A, 10kA, 415V, 50Hz FP MCB (C-curve)- 02Nos. Notes: [i] The panel shall be completely Ethernet communication ready to communicate with Energy Management System & shall be Web based application in-built [ii] 01No. of ON/OFF/trip status and operations counters as well as multi-function meters shall be wired to Ethernet Gateway part of the Panel

Supply, installation, commissioning and testing of factory made, CPRI approved, indoor, cubical compartmental type 'Typical Floor Panel', conforming to IEC 61439- 1 & 2, having both sides openable with hinged double doors & locking arrangement and IP 42 protection made out of 2mm thick mild steel CRCA sheet, supported and fixed on structural frame of angle iron, including earthing stud, labeling, painting to all internal & external exposed steel surfaces with powder coating paint (7 tank process), duly fixed on wall/floor with danger notice plate of 1.6mm thick mild steel sheet, vitreous enameled (white) with letters figures and conventional skull and bones in signal red colour, suitable for 3 Phase 4 Wire system, 500V grade with necessary wiring, PVC sheathed stranded copper conductor of appropriate length & size, including fixing lugs, bolts, screws, etc. complete all as specified and as directed Make: Schneider- Blokset, Siemens- Sivacon, ABB- MNS

The Typical Floor Panel shall comprise of the following: [a] Busbar Chamber: [i] Copper busbar of rated capacity 250A, covered with PVC insulated sleeves including insulator, nuts, bolts, etc. with complete connection- 01Set (3P+N) [b] Incoming: [i] 200A, 415V, Ics = Icu = 25kA, 50Hz, FP MCCB with adjustable overload settings (0.36-` X In) & tr = 0.5-16s, adjustable short-circuit settings (1.5-10 X Ir), adjustable earth- fault settings (0.2- 1 X In), current limiting type double break roto active type, instanteneous protection and microprocessor based trip unit- 01No. [ii] LED phase indicators (Red, Yellow, Blue)- 01Set [iii] Cl 1.0 multi-function meter capable of measuring V, A, F, PF, W/VA, Wh/VAh, Runhrs. Onhrs & interupts- 01No. [c] Outgoing: [i] 63A, 10kA, 415V, 50Hz FP MCB (C curve)- 03Nos.

Notes: [i] The panel shall be completely Ethernet communication ready to communicate with Energy Management System & shall be Web based application in-built [ii] 01No. of ON/OFF/trip status and operations counters as well as multi-function meters shall be wired to Ethernet Gateway part of the Panel

Supply, installation, commissioning and testing of factory made, CPRI approved, indoor, cubical compartmental type '22nd Floor Panel', conforming to IEC 61439- 1 & 2, having both sides openable with hinged double doors & locking arrangement and IP 42 protection made out of 2mm thick mild steel CRCA sheet, supported and fixed on structural frame of angle iron, including earthing stud, labeling, painting to all internal & external exposed steel surfaces with powder coating paint (7 tank process), duly fixed on wall/floor with danger notice plate of 1.6mm thick mild steel sheet, vitreous enameled (white) with letters figures and conventional skull and bones in signal red colour, suitable for 3 Phase 4 Wire system, 500V grade with necessary wiring, PVC sheathed stranded copper conductor of appropriate length & size, including fixing lugs, bolts, screws etc. complete all as specified and as directed Make: Schneider- Blokset, Siemens- Sivacon, ABB- MNS

The 22nd Floor Panel shall comprise of the following: [a] Busbar Chamber: [i] Copper busbar of rated capacity 200A, covered with PVC insulated sleeves including insulator, nuts, bolts, etc. with complete connection- 01Set (3P+N) [b] Incoming: [i] 125A, 415V, Ics = Icu = 25kA, 50Hz, FP MCCB with adjustable overload settings (0.36-` X In) & tr = 0.5-16s, adjustable short-circuit settings (1.5-10XIr), adjustable earth- fault settings (0.2-1XIn), current limiting type double break roto active type, instanteneous protection and microprocessor based trip unit- 01No. [ii] LED phase indicators (Red, Yellow, Blue)- 01Set [iii] Cl 1.0 multi-function meter capable of measuring V, A, F, PF, W/VA, Wh/VAh, Runhrs. Onhrs & interupts- 01No. [c] Outgoing: [i] 32A, 10kA, 415V, 50Hz FP MCB (C-curve)- 04Nos. [ii] 40A, 10kA, 230V, 50Hz SPN MCB (C-curve)- 02Nos.

[iii] 16A, 10kA, 230V, 50Hz SPN MCB (C-curve)- 01No. [iv] LED phase indicators (Red, Yellow, Blue)- 04Sets Notes: [i] The panel shall be completely Ethernet communication ready to communicate with Energy Management System & shall be Web based application in-built [ii] 01No. of ON/OFF/trip status and operations counters as well as multi-function meters shall be wired to Ethernet Gateway part of the Panel

Supply, installation, commissioning and testing of factory made, CPRI approved, indoor, cubical compartmental type 'Roof Floor Panel', conforming to IEC 61439- 1 & 2, having both sides openable with hinged double doors & locking arrangement and IP 42 protection made out of 2mm thick mild steel CRCA sheet, supported and fixed on structural frame of angle iron, including earthing stud, labeling, painting to all internal & external exposed steel surfaces with powder coating paint (7 tank process), duly fixed on wall/floor with danger notice plate of 1.6mm thick mild steel sheet, vitreous enameled (white) with letters figures and conventional skull and bones in signal red colour, suitable for 3- Phase 4 Wire system, 500V grade with necessary wiring, PVC sheathed stranded copper conductor of appropriate length & size, including fixing lugs, bolts, screws, etc. complete all as specified and as directed Make: Schneider- Blokset, Siemens- Sivacon, ABB- MNS

The Roof Floor Panel shall comprise of the following: [a] Busbar Chamber: [i] Copper busbar of rated capacity 200A, covered with PVC insulated sleeves including insulator, nuts, bolts, etc. with complete connection- 01Set (3P+N) [b] Incoming: [i] 63A, 415V, Ics = Icu = 16 kA, 50 Hz, FP MCCB with adjustable overload settings (0.36- X In) & tr = 0.5-16s, adjustable short-circuit settings (1.5-10 X Ir), adjustable earth- fault settings (0.2-1 X In), current limiting type double break roto active type, instanteneous protection and microprocessor based trip unit- 01No. [ii] LED phase indicators (Red, Yellow, Blue)- 01Set [iii] Cl 1.0 multi-function meter capable of measuring V, A, F, PF, W/VA, Wh/VAh, Runhrs. Onhrs & interupts- 01No. [c] Outgoing: [i] 32A, 10kA, 415V, 50Hz FP MCB (C-curve)- 02Nos. [iI] 32A, 10kA, 230V, 50Hz SPN MCB (C-curve)- 04Nos.

[iv] LED phase indicators (Red, Yellow, Blue)- 02Sets [v] Cl 1.0 multi-function meter capable of measuring V, A, F, PF, W/VA, Wh/VAh, Runhrs. Onhrs & interupts- 02Nos. Notes: [i] The panel shall be completely Ethernet communication ready to communicate with Energy Management System & shall be Web based application in-built [ii] 01No. of ON/OFF/trip status and operations counters as well as multi-function meters shall be wired to Ethernet Gateway part of the Panel [iii] The Panel shall be with wireless energy sensor on incomer and outgoing feeders for monitoring (V, I, P, PF, Energy), voltage loss alarm, Unbalance in phases. Same shall be communicated through Ethernet communication gateway to centralised Energy Monitoring System

Supply, installation, commissioning and testing of factory made, CPRI approved, indoor, cubical compartmental type 'Elevator Panel', conforming to IEC 61439- 1 & 2, having both sides openable with hinged double doors & locking arrangement and IP 42 protection made out of 2mm thick mild steel CRCA sheet, supported and fixed on structural frame of angle iron, including earthing stud, labeling, painting to all internal & external exposed steel surfaces with powder coating paint (7 tank process), duly fixed on wall/floor with danger notice plate of 1.6mm thick mild steel sheet, vitreous enameled (white) with letters figures and conventional skull and bones in signal red colour, suitable for 3- Phase 4 Wire system, 500 V grade with necessary wiring, PVC sheathed stranded copper conductor of appropriate length & size, including fixing lugs, bolts, screws etc. complete all as specified and as directed Make: Schneider Blokset, Siemens - Sivacon, ABB-MNS

The Elevator Floor Panel shall comprise of the following: [a] Busbar Chamber: [i] Copper busbar of rated capacity 200A, covered with PVC insulated sleeves including insulator, nuts, bolts, etc. with complete connection- 01Set (3P+N) [b] Incoming: [i] 160A, 415V, Ics = Icu = 25kA, 50Hz, FP MCCB with adjustable overload settings (0.36-XIn) & tr = 0.5-16s, adjustable short-circuit settings (1.5-10 X Ir), adjustable earth- fault settings (0.2-1XIn), current limiting type double break roto active type, instanteneous protection and microprocessor based trip unit- 01No. [ii] LED phase indicators (Red, Yellow, Blue)- 01Set [iii] Cl 1.0 multi-function meter capable of measuring V, A, F, PF, W/VA, Wh/VAh, Runhrs. Onhrs & interupts- 01No. [c] Outgoing: [i] 63A, 10kA, 415V, 50Hz FP MCB (C-curve)- 02Nos. [ii] 32A, 10kA, 415V, 50Hz FP MCB (C-curve)- 03Nos. [iii] 16A, 10kA, 415V, 50Hz FP MCB (C-curve)- 01No.

[iv] LED phase indicators (Red, Yellow, Blue)- 06Sets [v] Cl 1.0 multi-function meter capable of measuring V, A, F, PF, W/VA, Wh/VAh, Runhrs. Onhrs & interupts- 06Nos. Notes: [i] The panel shall be completely Ethernet communication ready to communicate with Energy Management System & shall be Web based application in-built [ii] 01No. of ON/OFF/trip status and operations counters as well as multi-function meters shall be wired to Ethernet Gateway part of the Panel [iii] The Panel shall be with wireless energy sensor on incomer and outgoing feeders for monitoring (V, I, P, PF, Energy), voltage loss alarm, Unbalance in phases. Same shall be communicated through Ethernet communication gateway to centralised Energy Monitoring System

S&F ISI marked MCB for AC applications till 63A, having breaking capacity Icn = 10kA, conforming to IS/IEC 60898-1-2002, sliding bottom clamp, colour coded on/off indication on dolly, biconnect IP 20 protected lower terminals and sliding shutters pf the following capacities complete all as specified and as directed Make: Schneider / Legrand / Havells

6A, SP MCB, C-curve

16A, SP MCB, C-curve

20A, SP MCB, C-curve

32A, SP MCB, C-curve

40A, SP MCB, C-curve

63A, FP MCB, C-curve

Supply, installation, testing and commissioning of Din Rail mounted, self-powered direct connect watt-hour meter, conforming to IEC 62053-21, with accuracy Cl 1.0 to provide direct measurement of real energy (kWh) on a single phase network (92 VA to 276 VAC) up to Imax, frequency range 50/60Hz, operating temperature range -25°C to 55°C with a 6+2 digit display for measurement up to 999999.99 in kWh and for configuration and equipped with a flashing red indicator to check the accuracy of the meter. The meter shall communicate via a Modbus RS-485 protocol and all measured values shall be available via the Modbus control, the meter shall be equipped with anti-tamper security feature to ensure the integrity of the measurement of the following complete all as specified and as directed:

3-Phase Din Rail Meter (Imax = 63A) Make: Schneider Cat-Part No. A9EM3150 or equivalent model of Legrand / Havells

1- Phase Din Rail Meter (Imax = 63A) Make: Schneider Cat-Part No. A9EM2150 or equivalent model of Legrand / Havells

Supply, installation and commissioning of 25litres electric geyser having temperature sensitive LED indicators, shock safe plug, PUF insulation, incoloy glass coated heating element, anode rod, adjustable knob, multi-functional safety valve with IP 4X protection complete all as specified and as directed Make: Havells Cat-Part No. GHWAPTTIV025 or equivalent model of Recold / Bajaj / Usha

Air Conditioning

Supply, install, testing and commissioning of 56HP capacity outdoor units, air cooled VRF / VRV system working in R410A / R-407C or equivalent refrigerant. The system shall be suitable to operate on 3 Phase, 380-415V, 50Hz AC power supply & shall comprises with multiple Nos. of inverter, digital scroll compressors, air cooled condenser fan with motor, microprocessor control panel, starter controls for all scroll compressors and condenser fan motors along with internal control and power wiring, cooling coil with internally interconnected refrigerant pipes for interconnecting various capacity modules (to make unit of 56HP), charging port and all other required accessories and hardwares, enclosed in an enclosure and entire unit shall be with weather resistant powder coating paint for withstanding all ambient conditions for continuous outdoor operation and

item No. 26.01 contd.. the system shall be internally interconnected including refrigerant pipes for interconnecting various modules (to make unit of 56HP), charging port, first charge of refrigerant as required and all other required accessories, hardwares like T joints, etc. complete all as specified and as directed Make: Daikin Model No. RXYQ56TRY6(E) or equivalent model of Blue Star / Carrier / Hitachi Notes: (i) The VRF/ VRV system shall be provided with mounting base and antivibration mountings. All the accessories, hardware, software, consumables etc. whether specifically mentioned or not but required to put the VRF / VRV HVAC systems into service to the entire satisfaction of the Engineer-in-charge including testing, commissioning as per specifications, site constraints shall be included by the bidder in the scope of the work

(ii) Nothing extra shall be payable for these systems under any circumstances. All the consumables including first charge of refrigerant (R-410A / R - 407C) and oil for the proposed VRF / VRV system shall be under the scope of the bidder. The topping of refrigerant and oil shall also be included in the quoted price for arresting leakages if any. The outdoor unit shall be installed on terrace of fourth floor of the building. The unit shall be lifted using crane / sufficient manpower and installed on suitable pedestal / MS rail / bots & nuts etc, all complete as requirement of site conditions (iii) Copper piping shall be measured and paid separately under respective item

Supply, install, testing and commissioning of 46HP capacity outdoor units, air cooled VRF / VRV system working in R410A / R -407C or equivalent refrigerant. The system shall be suitable to operate on 3 Phase, 380-415V, 50Hz AC power supply & shall comprises with multiple Nos. of inverter, digital scroll compressors, air cooled condenser fan with motor, microprocessor control panel, starter controls for all scroll compressors and condenser fan motors along with internal control and power wiring, cooling coil with internally interconnected refrigerant pipes for interconnecting various capacity modules (to make unit of 46 HP), charging port and all other required accessories, & hardwares, all complete shall be enclosed in an enclosure and the entire unit shall be with weather resistant powder coating paint for withstanding all ambient conditions for continuous outdoor operation and

item No. 26.04 contd.. the systems shall be internally interconnected including refrigerant pipes for interconnecting various modules (to make unit of 46HP), charging port, first charge of refrigerant as system required and all other required accessories, hardwares like T joints, etc. complete all as specified and as directed Make: Daikin Model No. RXYQ56TRY6(E) or equivalent model of Blue Star / Carrier / Hitachi Notes: (i) The VRF/ VRV system shall be provided with mounting base and antivibration mountings. All the accessories, hardware, software, consumables etc. whether specifically mentioned or not but required to put the VRF / VRV HVAC systems into service to the entire satisfaction of the Engineer-in-charge, including testing, commissioning as per specifications, site constraints shall be included by the bidder in the scope of the work

(ii) Nothing extra shall be payable for these systems under any circumstances. All the consumables including first charge of refrigerant (R-410A / R - 407C) and oil for the proposed VRF / VRV system shall be under the scope of the bidder. The topping of refrigerant and oil shall also be included in the quoted price for arresting leakages if any. The outdoor unit shall be installed on terrace of fourth floor of the building. The unit shall be lifted using crane / sufficient manpower and installed on suitable pedestal / MS rail / bots & nuts etc, all complete as requirement of site conditions (iii) Copper piping shall be measured and paid separately under respective item

Supply, install, testing and commissioning of 32HP capacity outdoor units, air cooled VRF / VRV system working in R410A / R -407C or equivalent refrigerant. The system shall be suitable to operate on 3 Phase, 380-415V, 50Hz AC power supply & shall comprises with multiple Nos. of inverter, digital scroll compressors, air cooled condenser fan with motor, microprocessor control panel, starter controls for all scroll compressors and condenser fan motors along with internal control and power wiring, cooling coil with internally interconnected refrigerant pipes for interconnecting various capacity modules (to make unit of 32HP), charging port and all other required accessories, & hardwares, all complete shall be enclosed in an enclosure and the entire unit shall be with weather resistant powder coating paint for withstanding all ambient conditions for continuous outdoor operation and

item No. 26.07 contd.. the systems shall be internally interconnected including refrigerant pipes for interconnecting various modules (to make unit of 56HP), charging port, first charge of refrigerant as system required and all other required accessories, hardware’s like T joints, etc. complete all as specified and as directed Make: Daikin Model No. RXYQ56TRY6(E) or equivalent model of Blue Star / Carrier / Hitachi Notes: (i) The VRF/ VRV system shall be provided with mounting base and antivibration mountings. All the accessories, hardware, software, consumables etc. whether specifically mentioned or not but required to put the VRF / VRV HVAC systems into service to the entire satisfaction of the Engineer-in-charge, including testing, commissioning as per specifications, site constraints shall be included by the bidder in the scope of the work

(ii) othing extra shall be payable for these systems under any circumstances. All the consumables including first charge of refrigerant (R-410A / R - 407C) and oil for the proposed VRF / VRV system shall be under the scope of the bidder. The topping of refrigerant and oil shall also be included in the quoted price for arresting leakages if any. The outdoor unit shall be installed on terrace of fourth floor of the building. The unit shall be lifted using crane / sufficient manpower and installed on suitable pedestal / MS rail / bots & nuts etc, all complete as requirement of site conditions (iii) Copper piping shall be measured and paid separately under respective item

Supply, installation, testing and commissioning of air cooled type four directional air flow DX Cassette type Indoor Air Conditioning Units of following capacity suitable for mounting inside false ceiling, each comprising of cooling coil, blower with multi speed motor, electronic expansion valve, supply & return air grilles, filter, insulated connection of refrigerant circuit, provision for fresh air intake ducting, condensate water drain pump with electronic level sensor, including wireless remote controller etc. with all required supports, anchor fasteners hardware, etc. interconnecting refrigerant copper piping, support etc. including power cabling of 3 core x 2.5mm² with 3 pin plug top in flexible conduit from units to the nearest plug point, control wiring of copper cables and interlocking with outdoor units for the following:

Notes: (i) All the indoor units shall be compatible to work with VRV / VRF type condensing unit (ii) The bidders shall include all the items required to put the cassette units into services after conducting all the tests as per specifications at no extra costs, whether specifically specified or not (iii) All the indoor units shall be compatible to work with VRV / VRF type condensing unit (iv) Copper piping shall be measured and paid separately under respective item

2.0TR ceiling suspended unit having 4-way / rounded uniform air flow with cordless remote controller as required Make: Daikin Model No. FXFQ63LUV1 or equivalent model of Blue Star / Carrier

4.0TR ceiling suspended unit having 4-way / rounded uniform air flow with cordless remote controller as required. Make: Daikin Model No.FXFQ125LUV1 or equivalent model of Blue Star / Carrier

Supply, installation, testing and commissioning of variable refrigerant flow distribution REFNUTS (Y- Joints) in the suction and liquid lines complete all as specified and as directed

M&L for 4 core 1.5mm² multi-strand screened shielded copper control cable, drawn in medium grade UPVC conduit of appropriate size to have interface between controller to individual unit cover complete all as specified and as directed Note: Size and make of the cable shall be acceptable as per the OEM recommendations

Supply, installation, testing and commissioning of refrigerant copper piping insulated with 19mm / 13mm thick Nitrile rubber of following sizes between outdoor unit to indoor units as per the specifications, refrigerant pipe shall be hard drawn / soft drawn copper pipe as per manufacture recommendations including connection between outdoor unit to indoor units as required and the piping shall be laid on walls / roof / ceiling well supported at specific intervals with metallic supports and screwed with anchor fasteners including all necessary accessories, jointing / brazing, etc. shall be carried out as required and all piping inside the ceiling shall be properly supported using necessary clamps and all externals refrigerant lines shall be properly protected using necessary PVC (HDPE) pipes with accessories to suit the site conditions complete all as specified and as directed

Notes: [i] The required size of pipe shall be as per the manufacturer's recommendations [ii] The quantity of these items of works shall be measured as per actual requirements of site conditions

(a) 41.3mm outer diameter (insulation 19mm thick)

(b) 34.9mm outer diameter (insulation 19mm thick)

(c) 28.6mm outer diameter (insulation 19mm thick)

(d) 22.2mm outer diameter (insulation 13mm thick)

(e) 19.1mm outer diameter (insulation 13mm thick)

(f) 15.9mm outer diameter (insulation 13mm thick)

(g) 12.7mm outer diameter (insulation 13mm thick)

(h) 9.5mm outer diameter (insulation 13mm thick)

(j) 6.35mm outer diameter (insulation 13mm thick)

M&L for following sizes UPVC drain water / fresh air arrangement pipe including bends, collars & elbow, etc. duly insulated with 9mm thick tubular insulation of closed cell elastomeric nitrile rubber as required complete all as specified and as directed

(a) 32mm nominal bore

(b) 50mm nominal bore

S&F 2mm thick 150x50mm perforated hot dipped galvanized iron cable tray having galvanization thickness not less than 50 microns and perforation not more than 17.5% including fittings viz. joints, bends, tees, etc. in convenient sections of length complete all as specified and as directed

Supply, installation, commissioning and testing of factory made, CPRI approved, indoor, cubical compartmental type 'HVAC Panel' of suitable size, conforming to IEC 61641, having both sides openable with hinged double doors & locking arrangement and IP 54 protection made out of 2mm thick mild steel CRCA sheet, supported and fixed on structural frame of angle iron of suitable size, including earthing stud, labeling, painting to all internal & external exposed steel surfaces with powder coating paint (7 tank process), duly fixed in ground with PCC foundation (1:2:4) type B1, with danger notice plate of 1.6mm thick mild steel sheet, vitreous enameled (white) with letters figures and conventional skull and bones in signal red colour, suitable for 3 Phase 4 Wire system, 500V grade with necessary wiring, PVC sheathed stranded copper conductor of appropriate length & size, including fixing lugs, bolts, screws, etc. comprising of the undermentioned specifications complete all as specified and directed Make: Schneider Blokset, Siemens - Sivacon, ABB-MNS

The HVAC Panel shall comprise of the following: [a] Busbar Chamber: [i] Copper busbar of rated capacity 500A, covered with PVC insulated sleeves including insulator, nuts, bolts, etc. with complete connection- 01Set (3P+N)

[b] Incoming: [i] 320A, 415V, Ics = Icu = 25kA, 50Hz, FP MCCB with adjustable overload settings (0.36-1 X In) & tr = 0.5 - 16s, adjustable short-circuit settings (1.5 -10 X Ir), adjustable earth- fault settings (0.2-1 X In), instanteneous protection and microprocessor based trip unit- 01No. [ii] LED phase indicators (Red, Yellow, Blue)- 01Set [iii] Power Measurement Device with Class 0.5S accuracy, complying to IEC 62053- 22, dual ethernet ports for daisy chain communication, 64 samples/cycle, data logging, up to 31st harmonic analysis, 2 DI, 2 DO, 2 RO, 35 alarms - 03Nos.

[c] Outgoing: [i] 100A, 415V, Ics = Icu = 16kA, 50Hz, FP MCCB with adjustable overload settings (0.36- 1 X In) & tr = 0.5 - 16s, adjustable short-circuit settings (1.5 - 10 X Ir), adjustable earth- fault settings (0.2- 1 X In), instanteneous protection and microprocessor based trip unit- 03Nos. [i] 63A, 415V, Ics = Icu = 16kA, 50Hz, FP MCCB with adjustable overload settings (0.36- 1 X In) & tr = 0.5 - 16s, adjustable short-circuit settings (1.5 -10 X Ir), adjustable earth- fault settings (0.2-1 X In), instanteneous protection and microprocessor based trip unit- 01No. [iv] LED phase indicators (Red, Yellow, Blue)- 04Sets [v] Cl 1.0 multi-function meter capable of measuring V, A, F, PF, W/VA, Wh/VAh, Runhrs. Onhrs & interupts- 04Nos.

Notes: [i] The Panel shall be completely Ethernet communication ready to communicate with Energy Management System & shall be Web based application in-built [ii] 05Nos. of ON/OFF/trip status and operations counters as well as multi-function meters shall be wired to Ethernet Gateway part of the panel

Fire Fighting System

M&L for copper conductor, XLPE insulated armoured cables, conforming to IS: BS EN 60228, having annealed copper conductor, PVC inner sheath, single armouring of galvanized round steel wire, one layer of PETP tape wrapping, collective screen of PETP/aluminum tape over tinned copper drain wire, RED in colour, including clamping, termination and ferruling complete all as specified and as directed Make: Gloster, Havells or Polycab

2 core 1.5sqmm

2 core 2.5sqmm

Supply, installation, commissioning and testing of factory made, CPRI approved, indoor, cubical compartmental type 'Motor Control Center' (MCC) of suitable size, conforming to IEC 61641, having both sides openable with hinged double doors & locking arrangement and IP 54 protection made out of 2.00 mm thick mild steel CRCA sheet, supported and fixed on structural frame of angle iron of suitable size, including earthing stud, labeling, painting to all internal & external exposed steel surfaces with powder coating paint (7 tank process), duly fixed in ground with PCC foundation (1:2:4) type B1, with danger notice plate of 1.6mm thick mild steel sheet, vitreous enameled (white) with letters figures and conventional skull and bones in signal red colour, suitable for 3 Phase 4 Wire system, 500V grade with necessary wiring, PVC sheathed stranded copper conductor of appropriate length & size, including fixing lugs, bolts, screws, etc. complete all as specified and as directe Make: Schneider Blokset, Siemens - Sivacon, ABB-MNS

[v] 320A, 415V, Ics=Icu=36kA, 50Hz, FP MCCB with adjustable overload settings (0.36-1Xin) and tr=0.5-176s, adjustable short-circuit settings (1.5-10x lr), adjustable earth-fault Settings(0.2 Xin), current limiting type double break roto active type, instantenous protection and micropressor based trip unit - 02Nos. [vi] Cl 1.0 multi-function meter capable of measuring V, A, F, PF, W/VA, Wh/VAh, Runhrs. Onhrs & interupts- 05 Nos [vii] LED phase indicators (Red, Yellow, Blue)- 05sets

Notes: [i] The Panel shall be completely Ethernet communication ready to communicate with Energy Management System & shall be Web based application in-built [ii] 06Nos. of ON/OFF/trip status and operations counters as well as multi-function meters shall be wired to Ethernet Gateway part of the panel

Supply, installation, testing and commissioning of 2- way fire brigade draw- off connection with two 63mm NB inbuilt gunmetal non-return valves instanteneous coupling type arranged on 100mm NB pipe manifold and connected to wet riser main as well as to fire water tank including CI butterfly valve, CI non-return valve and MS cabinet with mounting supports, etc. all complete as specified and as directed Make: Minimax, Vijay, Safex, Ceasefire

Supply, installation, testing and commissioning of 'Sprinkler Annunciation Panel' compatible for seamless integration with water flow devices with visual display, internal sounder, alarm/fault indications and stand-by 24V lead-acid batteries with charger complete all as specified and as directed Make: Tyco, Agni, Safex Note: The panel shall be located in the Fire Pump House and connected to flow indicating switches in sprinkler system

M&L for construction of brick masonry valve chamber of size 1000x800x1000mm (internal dimenssions) with PCC foundation 1:4:8 type D2 using 40mm graded stone aggregate, 150mm thick & 150mm wide offsets around over 100mm thick hardcore, 200mm thick fly-ash brick masonry walls built in CM 1:6, 100mm thick PCC 1:2:4 type B1 coping finished even and smooth, rendering 10mm thick in cement mortar (1:6) finished even and smooth, with out using extra cement internally including top of floor including excavation earth work in hard/dense soil 6mm thick MS sheet cover fixed on 25x25x6mm thick angle iron frame with hold fasts embedded in PCC coping with locking arrangement, mild steel handle and painting to steel surfaces with two coats of synthetic enamel paint over one coat of primer including disposal of surplus soil to a distance not exceeding 50m, etc. complete all as specified and as directed

Supply, installation, testing and commissioning of electric motor driven horizontal end-suction & top discharge, back pull-out type centrifugal pump, confirming to IS: 12469- 2011, with CI casing, bronze impeller and stainless steel shaft, mechanical seal, etc. to deliver 2850LPM at 150m head coupled with a spacer coupling to a 2 pole TEFC type squirrel cage induction motor of suitable HP with IP 55 protection of enclosure at 2900RPM speed, efficiency not less than 55%, suitable for operation on 415V ±10%, 3-Phase, 50Hz AC supply, horizontal foot-mounted type with class F insulation, confirming to IS: 325-1978, with coupling guard, foundation as per manufacturer's recommandation, etc. complete all as specified and as directed Make: Kirloskar, Mather & Platt, Crompton Greaves

Supply, installation, testing and commissioning of diesel engine driven horizontal end-suction & top discharge, backpull out type centrifugal pump, conforming to IS: 12469- 2011, with CI casing, bronze impeller and stainless steel shaft, mechanical seal, etc. mounted on heavy duty bearings, couplings, zero access type coupling guard, etc. capable to deliver 2850LPM at 150m head. The pump shall be coupled to a water-cooled radiator, diesel engine of suitable BHP & speed, two sets of batteries of adequate rating with suitable for battery leads & stand, battery charger, residential silencer, diesel tank of capacity adequate for 6hours of operation and fitted with level and exhaust silencer, the complete set shall be mounted on common base frame including foundation as per manufacturer's recommendation complete all as specified and as directed Make: Kirloskar, Mather & Platt, Crompton Greaves

Supply, installation, testing and commissioning of electric motor driven horizontal end-suction & top discharge, back pull-out type centrifugal jockey pump, confirming to IS: 12469- 2011, with CI casing, bronze impeller and stainless steel shaft, mechanical seal, etc. to deliver 180LPM at 90m head coupled with a spacer coupling to a 2 pole TEFC type squirrel cage induction motor of suitable HP with IP 55 protection of enclosure at 2900RPM speed, efficiency not less than 55%, suitable for operation on 415V ±10%, 3-Phase, 50Hz AC supply, horizontal foot-mounted type with class F insulation, confirming to IS: 325-1978, with coupling guard, foundation as per manufacturer, complete all as specified and as directed Make: Kirloskar, Mather & Platt, Crompton Greaves

Cable TV & Telephone Wiring & Conduiting

S&F modular type 1 module RJ 11 telephone socket with shutter complete all as specified and as directed Make: Legrand Arteor Cart-Part No. 5734 26 or equivalent model of Precision / Roma

S&F modular type 1 module TV socket complete all as specified and as directed Make: Legrand Arteor Cat-Part No. 5734 25 or equivalent model of Precision / Roma

S&F PVC junction box of size 250x200x100mm for TV cable complete all as specified and as directed Make: Sintex Cat-Part No. GSJB 2520 or equivalent model of Hensel / National / Roma

S&F 50 pairs krone type telephone junction box of size 9.5"x7.5"x3.5" including one backmount frame and earthing, foxed key style secure lock, easy to open door complete all as specified and as directed Make: Hensel / Sintex

S&F DLP UPVC trunking of size 105x50mm for TV / telephone cable with accessories for the following complete all as specified and as directed

(a) Plastic trunking without cover of size 105x50mm Make: Legrand Cat-Part No. 0104 22 or model of Precision / Roma

(b) 40mm wide flexible cover Make: Legrand Cat-Part No. 0105 20 or equivalent equivalent model of Precision / Roma

(c) Joints for 40mm wide cover Make: Legrand Cat-Part No.0108 00 or equivalent equivalent model of Precision / Roma

(d) Base/body joints Make: Legrand Cat-Part No. 0106 91 or equivalent equivalent model of Precision / Roma

(e) Clips Make: Legrand Cat-Part No. 0106 82 or equivalent equivalent model of Precision / Roma

(f) Separation partitions Make: Legrand Arteor Cart-Part No. 0105 82 or equivalent model of Precision / Roma

(g) End caps Make: Legrand Arteor Cart-Part No. 0107 02 or equivalent model of Precision / Roma

Standby Power Supply (DG Set)

Supply, installation, testing and commissioning of silent DG Set, conforming to IS: 10002-1981 with Diesel Engine of suitable BHP & AC Brushless SPDP alternator, conforming to IS: 13364-1992, mounted on a common base frame & coupled through a flexible coupling or close coupled and AMF Panel complete with platform, control panel having meters, sound-proof canopy, etc. of capacity 125kVA of the following specifications laid as under complete all as specified and as directed Make: Kirloskar / Crompton Greaves / Cummins

[a] Engine: 4/6 cylinder, in-line, 4 stroke, radiator cooled engine, well designed air handling system with dry type, heavy duty, replaceable paper element air cleaner with restriction indicator, air to air aftercooling, optimised turbocharger for increased altitude,Inline fuel pump with A1 class mechanical governing, spin on fuel filter, standard integral set-mounted radiator system, designed and tested for 50°C ambient temperature, full flow spin on lube oil filter, electrical starter motor with soft start engagement feature, ƒƒbattery charging alternator with 1x12V DC battery [b] Alternator: ƒƒBrushless type, screen protected, revolving field, self-excited alternator, conforming to IS/IEC 60034-1 3-phase reconnectable winding with 12 terminals brought out for connection, dedicated winding specially designed for single operation, impregnation on all wound components for better mechanical strength

[c] Control Panel: Manufactured with 14/16 gauge CRCA sheet and powder coated for weather-proof and long lasting finish The control panel consists of the following parts: [i] Controller: Aluminum bus bars with suitable capacity with incoming/outgoing terminals [ii] Indicating lamps for ‘Load ON’ and ‘Set Running’ [iii] Instrument fuses duly wired and ferruled [iv] MCCB of suitable rating with overload and short circuit protections [d] Microprocessor based generator set monitoring and control system including an intuitive operator interface that allows for complete generator set control as well as system metering, fault annunciation, configuration and diagnostics, LED backlit LCD display with tactile feel soft-switches & generator set status LED lamps, remote START-STOP [e] Engine Metering: Oil pressure, engine temperature, starting battery voltage, engine running hours

ƒƒ[f] AC Alternator Metering: L-L voltage and L-N voltage, current (phase and total), kVA (phase and total) and frequency ƒ[g] ƒEngine Protection: Low lube oil pressure, high/low coolant temperature, battery over/under/weak volts, fail to crank/start, sensor failure, cranking lockout, low fuel level [h] AC Alternator Protection: Over/under voltage, over/under frequency, loss of AC sensing [i] Data Logging: Engine hours, control hours and upto 5 recent fault codes [j] Configurable glow plug control [k] ƒƒ12V DC operation [l] Silencer: ƒƒCritical grade silencer suitably optimized to meet stringent noise emission standards laid down by MoEF / CPCB

item No. 29.01 contd.. [m] Mounting Arrangement: Engine and alternator are mounted on a common MS fabricated base frame with AVM pads [n] ƒƒBase frame with integral fuel tank is provided with drain plug, air vent, inlet and outlet connection, level indicator and provision for cleaning

Aviation Lights

S&F LED aviation / obstruction light including LED having intensity > 40 cd, die-cast aluminium body, UV stabilized optical lens for 360o illumination, inbuilt on-off photo cells, ERDA type tested and comforming to ICAO/FAA standards, IP 65 rated operating on 90- 270V, 50Hz, 1- Ph AC supply complete all as specified and as directed Make: Bajaj Cat-Part No. BGAV 302 LED or equivalent model of Philips / Wipro

M&L for ISI marked 1.1kV grade copper conductor, XLPE insulated 2 core, 1.5sqmm armoured cables, conforming to IS: 7098 (Part-1)-1988 having stranded copper compact shaped conductor as per clause-2, IS: 8130-1984, PVC inner sheath, single armouring of galvanized steel strip/wire and PVC Type ST- 2 outer sheath conforming to IS: 5831-1984, including clamping and termination complete all as specified and as directed Make: Finolex, Havells, Polycab

Solar Water Heating System

S&F bib cock 15mm dia, fancy type, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and as directed Make: Jaquar Model No. CQT-23047 GD or equivalent model of (Flow rate 4.0LPM) Crab Tree / Kohler

Refrigerators & Water Coolers

Supply, installation, commissioning of refrigerator, electric driven single phase having storage and nominal cooling capacity 310- 360litres complete all as specified and as directed Make: Godrej / LG / Voltas / Samsung

Mechanical Laundry

Supplying, installing, testing and commissioning washing machine, front loading type, open pockets with low spin extract of capacity 60kg, electrically operated with all requisite electrical connections including all necessary accessories complete all as specified and as directed Make: IFB / LG / Voltas / Samsung / Whirlpool

Supplying, installing, testing and commissioning hydro-extractor, direct drive type, self balancing, automatic DC injection brake, of capacity 60kg, electrically operated with all requisite electrical connections including all necessary accessories complete all as specified and as directed Make: IFB / LG / Voltas / Samsung / Whirlpool

Supplying, installing, testing and commissioning drying tumbler, front loading, reversible with automatic cool down feature of capacity 60kg, electrically operated with all requisite electrical connections including all necessary accessories complete all as specified and as directed Make: IFB / LG / Voltas / Samsung / Whirlpool

External Water Supply

Supply, installation, testing and commissioning of end-suction & top-discharge, non-self-priming, single-stage, centrifugal volute type pump having cast iron casing, enclosed type dynamically balanced phosphor-bronze/SS impeller, high tensile steel shaft, carbon steel stuffing box (sealed by mechanical seal), deep groove ball bearings, TEFC squirrel cage induction motor having IE- 3 efficiency, conforming to IS: 12615- 2018 at 2900RPM speed star/delta starter panel, base plate, mounting channel frame, accessories and fittings, viz. mechanical seal, pressure gauges, thermometers, drains, coupling, coupling guard, vibration isolation arrangement by means of spring/rubber type mounting suitable for operation on 3 Phase, 415V ± 10%, 50Hz AC supply including foundation as per the manufacturer's recommendations complete all as specified and as directed Make: Kirloskar, Mather & Platt, Crompton Greaves

Horizontal end suction long coupled type pump with insulation suitable for 420LPM water flow rate at 94m head for domestic water supply

Horizontal end suction long coupled type pump with insulation suitable for 192LPM water flow rate at 90m head for flushing water supply

Supply, installation, testing and commissioning of PN 1.0 rated CI 'Y' -type strainer for suction conforming to IS: 907-1984 with SS filter screen and flange drilling standard end connection conforming to IS: 1538-1993 and necessary accessories for suction side of fire pumps complete all as specified and as directed Make: Kirloskar, Leader, Venus

(a) 100mm nominal bore

(b) 80mm nominal bore

Supply, installation, testing & commissioning of Programmable Logic Controller based Pump Automation and Protection Indoor type Slave Panel with dual wireless communication facility suitable for 02Nos. pumps , 01No. ultrasonic level sensor, 02Nos. pressure switches, 02Nos. priming valves, 02Nos. solenoid valves, 06Nos. motorised valves and 03Nos. magnetic sensors with minimum suitable size fabricated from 1.6mm thik CRCA sheet and duly powder coated to operate the water supply system and act as a user control and audio-visual indication system and it shall be wall mounted / floor mounted and the PLC Panel shall be with the following features: Make: RECKTRONIC DEVICES & SYSTEMS / INTEGRATED CONTROL SYSTEMS / MARSH AUTOMATION

(a) Water Level Sensing & Display (b) Pump On/Off (c) Auto priming (d) Operation of Motor Actuated Butterfly Valves (e) Automatic Toggling Of Pumps (f) Auto Change Over in Case of Pump Failure (g) Single Phasing Preventor (h) Manual Mode Operation

Supply, installing, testing and commissioning of ultrasonic level transmitter at domestic water tank (for measurement of level) complete all as specified and as directed and of the following specifications: Range: 0-2meters Accuracy: 0.5 % minimum Supply Voltage: 24V DC Output: 4-20mA Make: Banner / ABB / Emerson / Kroshne Marshall

Supply, installing, testing and commissioning of motor actuated butterfly valves with appropriate bracket / mounting arrangement including two nos. limit switches for open and closed condition and splash proof encloser along with wafer type butterfly valve complete all as specified and as directed with the following specifications: Valve size: 50mm dia Designed line pressure: 10kg/sqcm Operating Angle: 90o Disc Material: CI with nylon coating Limit Switches: 02Nos. for Open and Close Mounting: Direct Make: RITETORK / HASSEL HOFENER / EMTORK

Supply, installing, testing and commissioning of motor actuated butterfly valves with appropriate bracket / mounting arrangement including 02Nos. limit switches for open and closed condition and splash proof encloser along with wafer type butterfly valve complete all as specified and as directed with the following specifications: Valve size: 40mm dia Designed line pressure: 10kg/sqcm Operating angle: 90o Disc Material: CI with nylon coating Limit Switches: 02Nos. for Open and Close Mounting: Direct Make: RITETORK / HASSEL HOFENER / EMTORK

M&L for ISI marked 1.1kV grade 2 core 1.5mm² copper conductor, XLPE insulated armoured cables, conforming to IS: 7098 (Part-1) 1988 having stranded copper compact shaped conductor as per clause 2, IS: 8130-1984, PVC inner sheath, single armouring of galvanized steel strip/wire and PVC Type ST- 2 outer sheath conforming to IS: 5831- 1984, including termination complete all as specified and as directed Make: Universal Cables / Asian Cables (RPG) / CCI / Polycab

M&L for construction of brick masonry valve chamber of size 1000x800x1000mm (internal dimensions) with PCC foundation 1:4:8 type D2 using 40mm graded stone aggregate, 150mm thick & 150mm wide offsets around over 100mm thick hardcore, 200mm thick fly-ash brick masonry walls built in CM 1:6, 100mm thick PCC 1:2:4 type B1 coping finished even and smooth, rendering 10mm thick in cement mortar (1:6) finished even and smooth, with out using extra cement internally including top of floor including excavation earth work in hard/dense soil 6mm thick MS sheet cover fixed on 25x25x6mm thick angle iron frame with hold fasts embedded in PCC coping with locking arrangement, mild steel handle and painting to steel surfaces with two coats of synthetic enamel paint over one coat of primer including disposal of surplus soil to a distance not exceeding 50m complete all as specified and as directed

M&L for cutting 150mm NB cast iron pipe and reducing to required length before laying in position for insertion of new tees, branches, etc. including bends, tapers, tee pieces (single & double branch) any type and angle/radius and straight connecting pieces but all ends flanged complete all as specified and as directed

External Electrification

Supply, installation, testing, commissioning of energy efficient (level 2) 2500kVA, 11/0.433kV, oil immersed, KNAN cooled, 3 Phase step-down distribution transformer suitable for 11kV, 50Hz distribution and conforming to IS: 1180 (Part-1): 2014, including first filling of natural easter vegetable oil, conforming to IS: 16659- 2017, having dielectric breakdown strength ≥ 50kV, CRGO bolt-less prime grade core, M4 or better directly from reputed manufacturers like Nippon / Posco/ AK steels ensures high endurance of core HV & LV windings wound from super enamel covered electrolytic grade copper conductor with tapping on the HV winding for variation of HV voltage within range of +5% to -15% in steps of 2.5%, hermatically sealed corrugated tank, HV/LV cable boxes complete with all standard fittings/accessories and mounted on a platform as per manufecturer's recommendations complete all as specified and as directed Make: Schneider, ABB, Siemens

The transformer shall conform to the following specific parameters: [i] System Voltage: 12kV [ii] Rated Voltage (HV/LV): 11 /0.433kV [iii] Frequency: 50Hz ±3% [iv] No. of Phases: 3 [v] Connection (HV/LV): Delta / Star (neutral brought out) [vi] Vector Group: Dyn-11 [vii] Type of Cooling: KNAN [viii] Audible Sound Level: < 75dB

[ix] Insulation Level: (1) HV Peak Impulse Voltage: 75kV (2) HV Power Frequency Voltage: 28kV (3) LV Power Frequency Voltage: 2kV [x] Impedance: 6.25% [xi] Maximum Losses: (1) at 50% loading: 5.05kW (2) at 100% loading: 15kW [xii] Cable Box Clearance: (1) HV: 127mm Phase to Phase: 76mm Phase to Earth (2) LV: 45mm Phase to Phase; 20mm Phase to Earth [xiii] Terminal Markings: (1) HV: 1U, 1V, 1W (2) LV: 2u, 2v, 2w, 2n [ixv] Off Circuit Tap Changer (OCTC): ±7.5% in steps of 2.5%

The following standard fittings/accessories shall be provided along with the transformer: [i] Non-detachable rating & terminal marking plates [ii] Monogram plate [iii] Lifting lugs for main tank & top cover & jacking lugs [iv] Top filter valve [v] Drain cum bottom filter valve [vi] Oil sampling valve [vii] Earthing terminals with lugs: 2Nos. [viii] Storage & instruction plate [ix] Skid type under base [x] Bi-directional plain/flange rollers [xi] Detachable type radiators with top & bottom shut-off valve [xii] WTI & OTI with alarm & trip contact [xiii] Marshalling box [ixv] Magnetic Oil level gauge low oil level alarm contact

Notes: [i] The bidder shall furnish dimensional drawings of the items offered indicating all the fittings, dimensional tolerances, typical GADs of the windings with details of insulation at each point and core construction, etc. for approval of the accepting officer [ii] The bidder shall intimate the accepting officer for the routine tests in accordance with IS: 2026 in the OEM factory in presence of a representative nominated by the accepting officer before dispatch

Supply, installation, testing and commissioning of 4000A sandwich type silver flashed, bi-metal copper contact, aluminium busway (3L+N+PE), with original Mylar insulation from Dupont, 100% neutral, 120kA for 1second, 50% integral earth, dual housing having the under mentioned technical specifications complete all as specified and as directed Make: Schneider, ABB, Siemens

The busbar trunking system shall conform to the following technical specifications: [A] General: [i] The busbar trunking system (BTS), both feeder and plug-in, shall be of sandwich construction. All components and fittings (straight length, elbow, tees, flanged ends, cable tap box and circuit breaker, etc.) shall be in accordance with IEC 61439 Part 6 (2012) or UL857 and from the same manufacturer as the busbar trunking system. Degree of protection of the BTS shall be IP 54 in accordance with IEC 60529 [ii] Rated operation voltage of the BTS shall be 1kV. The neutral conductor shall have the same cross-sectional area as the phase conductor. The earth busbar must be one continuous piece without bolting on housing.

[B] Certificate: [i] The busbar, of full range and each rating, shall pass full type tests specified in IEC 61439-6. The certificate shall be issued by an international independent testing authority (e.g. ASTA, KEMA, UL) [ii] A product safety mark (e.g. KEMA-KEUR, ASTA DIAMOND, UL) shall be on the product offering a visible assurance to all of full product safety testing, factory inspection and ongoing surveillance under independent authority to ensure the ongoing safety of product [iii] The BTS shall pass seismic tests with actual physical product and being certified complying with UBC seismic Zone 4 condition by an international recognized earthquake research body, e.g. Asian Pacific Network of Centers for Earthquake Engineering Research (ANCER)

[C] Short-Circuit Ratings & Tests: [i] The whole BTS shall be capable of withstanding the short circuit of the electrical installation without undergoing any electrical, mechanical and thermal stress under fault condition at a service voltage of 1kV at 50Hz frequency. The minimum rated insulation voltage shall be 1kV [ii] Minimum certified short circuit ratings shall be 198kA peak and 90kA for 1sec for 3200A BTS.

[D] Housing: [i] The busbar trunking housing shall be constructed of electro galvanized steel and aluminum to reduce hysteresis and eddy current loses and shall be provided with a suitable protective finish of ANSI 49 grey epoxy paint [ii] The busbar trunking housing shall be totally enclosed non-ventilated for protection against mechanical damage and dust accumulation. And it shall pass at least 2000hr salt spray test to ensure the anticorrosion ability [iii] The totally enclosed housing shall be manufactured by the busbar trunking manufacturer. Modifications of busbar trunking to make it totally enclosed by housing other than the busbar trunking manufacturer voids the manufacturer’s warranty. Busbar trunking so modified is unacceptable without the written consent of the manufacturer

[E] Busbars: [i] Busbars shall be of aluminum with copper cladding utilized Molecular Fusion technology [ii] There shall be no bolts passing through the busbars of the busway [iii] Each busbar shall be insulated with Class-B (130oC) DuPont Mylar insulation. Epoxy insulation is unacceptable [iv] The temperature rise at any point of the busbar trunking enclosure shall not exceed 55°C above the ambient temperature of 40°C when operated at rated current

[F] Joints: [i] The busbar trunking joint shall be of the one-bolt type which utilizes a high strength steel bolt(s) and Belleville washers to maintain proper pressure over a large contact surface area [ii] The bolt shall be torque indicating and at earth potential [iii] The bolt shall be two-headed design to indicate when proper torque has been applied and require only a standard long handle wrench to be properly activated [iv] Access shall be required to only one side of the busbar trunking for tightening joint bolts [v] It shall be possible to remove any joint connection assembly to allow electrical isolation or physical removal of a busbar trunking length without disturbing adjacent busbar trunking lengths

[G] Plug-in Openings: [i] The connecting jaw of the plug-in unit shall plug directly on to the busbar and have full contact with busbar itself. Welded tab at plug-in busbar is unacceptable [ii] All contact on joint and plug-in opening should be silver plated copper [iii] On plug-in busbar trunking there shall be three dead front, hinged cover type plug-in openings on each side [iv] All openings shall be usable simultaneously [v] Busbar trunking shall be installed so that plugs are side mounted to permit practical use of all plug-in openings [vi] It shall be possible to inspect the plug-in opening and busbars prior to the installation of the plug-in units [H] Plug-in Units: [i] The plug-in jaw shall be spring design composed of different metal to ensure the firm and tight contact with the busbar

[ii] Plug-in Units shall be type tested in accordance with IEC 61439-6 (Annex D: Part 1-5 and 9-13) [iii] The earthing contact of the plug-in unit shall always be made before that of the live conductors and the last to break during removal. And it must connect to the earth bar of busway to ensure the safety [iv] Covers of all plug-in units must have interlocks to prevent the cover from being opened when the switch is in the ON position [v] Plug-in units (circuit breaker type or fusible switch type) shall be operated with visible blade quick-make and quick-break mechanism [vi] Presence of transparent shield shall be inside to avoid direct contact of human [vii] The plug-in units shall be equipped with internal barriers to prevent accidental contact of fish tape and conductors with live parts on the line side of the protective device during time of wire pulling.

[I] Supporting Structure: Indoor feeder and plug-in busbar trunking shall be approved for hanger spacing of up to 3m for horizontally mounted run and 4.88m for vertically mounted runs. Outdoor feeder busbar trunking shall be approved for spacing of up to 1.5m for horizontally or vertically mounted runs [J] Voltage Drop: [i] The 3 phase line to line voltage drop 40% power factor concentrated loadshall not exceed 3.4V per hundred feet [ii] The line-to line voltage drop at the load power factor shall not exceed 4.1V per hundred feet

(a) Straight feeder

(b) 90º elbow

(c) Flange end

(d) Copper flexible (braided)

(e) Adopter box (local item)

(f) Edge-wise hangers

Supply, installation, commissioning and testing of factory made, CPRI approved, indoor, cubical compartmental type 'Main LT Panel' of suitable size, conforming to IEC 61439-1 &2, IEC 61641, having both sides openable with hinged double doors & locking arrangement and IP 42 protection made out of 2mm thick mild steel CRCA sheet, supported and fixed on structural frame of angle iron of suitable size, including earthing stud, labeling, painting to all internal & external exposed steel surfaces with powder coating paint (7 tank process), duly fixed in ground with PCC foundation (1:2:4) type B1, with danger notice plate of 1.6mm thick mild steel sheet, vitreous enameled (white) with letters figures and conventional skull and bones in signal red colour, suitable for 3 Phase 4 wire system, 500V grade with necessary wiring, PVC sheathed stranded copper conductor of appropriate length & size, including fixing lugs, bolts, screws, etc. complete all as specified and as directed Make: Schneider- Blokset, Siemens- Sivacon, ABB- MNS

The main LT panel shall comprise of the following: [a] Busbar Chamber: [i] Copper busbar of rated capacity 5000A, covered with PVC insulated sleeves including insulator, nuts, bolts, etc. with complete connection-01Set (3P+N)

[iii] Power Quality analyzer with revenue accuracy of Class 0.2S, complying to IEC 62053- 22, 256 samples/cycle, waveform reading, 512MB of standard non-volatile memory for data & event logging, up to 63rd harmonics analysis for voltage & current, GPS clock, 01 serial port (Modbus, ION, DNP3), Dual Ethernet port (Modbus/TCP, ION TCP, DNP3 TCP, IEC 61850) and standard digital input, expandable digital IO, analog IO.- 03Nos. [iv] LED phase indicators (Red, Yellow, Blue)- 03Set Notes: [i] The panel shall be completely Ethernet communication ready to communicate with Energy Management System & shall be Web based application in-built [ii] 04Nos. of ON/OFF/trip status and operations counters as well as multi-function meters shall be wired to Ethernet Gateway part of the Panel

Supply, installation, testing & commissioning of indoor type APFC Bank Panel, having MPP type capacitor with 7% aluminum wound reactor units tested in accordance with IS 16636: 2017 with contactor switching, semi compartmentalised suitable for 3 Phase, 4 wire, 440V, AC Supply made out of 2mm thick CRCA sheet with built upon rigid frame work, cubical type of capacity 500kVAR i.e. (2x25 + 3x50 + 3x100) capacitor bank and Induced air system provided axial flow fan or centrifugal fan, having following accessories including control wiring with FRLS copper wire complete all as specified and as directed and as per specifications laid hereinafter Make: Schneider Varset Cat-Part No. VCLVW7C20500B6M or equivalent model of ABB / Siemens

[ii] 3P, 25kVAR Power contactor, 415V, 230V AC coil- 02Nos. [iii] 7% detuned reactor, 440V, Al wound type, 25kVAR- 02Nos. For 50kVAR: (3 STEP) [i] 100A, 415V, Ics = Icu = 36kA, 50Hz, TP MCCB with fixed magnetic settings and adjustable thermal settings (0.7 - 1 X In)- 3Nos [ii] 3P, 50kVAR Power contactor, 415V, 230V AC coil- 01No. [iii] 7% detuned reactor, 440V, Al wound type, 50kVAr- 01No. For 100kVAR: (3 STEPS) [i] 200A, 415V, Ics = Icu = 25kA, 50Hz, TP MCCB with fixed magnetic settings and adjustable thermal settings (0.7 - 1 X In)- 3Nos. [ii] 3P, 100kVAR Power contactor, 415V, 230V AC coil- 03Nos. [iii] 7% detuned reactor, 440V, Al wound type, 100kVAR-03Nos.

Supply, installation, commissioning and testing of factory made, CPRI approved, indoor, cubical compartmental type 'Utilities Panel' of suitable size, conforming to IEC 61439-1 & 2, IEC 61641, having both sides openable with hinged double doors & locking arrangement and IP 42 protection made out of 2mm thick mild steel CRCA sheet, supported and fixed on structural frame of angle iron of suitable size, including earthing stud, labeling, painting to all internal & external exposed steel surfaces with powder coating paint (7 tank process), duly fixed in ground with PCC foundation (1:2:4) type B1, with danger notice plate of 1.6mm thick mild steel sheet, vitreous enameled (white) with letters figures and conventional skull and bones in signal red colour, suitable for 3 Phase 4 wire system, 500V grade with necessary wiring, PVC sheathed stranded copper conductor of appropriate length & size, including fixing lugs, bolts, screws, etc. complete all as specified and as directed and as per specifications laid hereinafter Make: Schneider- Blokset, Siemens- Sivacon, ABB- MNS

The Utilities Panel shall comprise of the following: [a] Busbar Chamber: [i] Copper busbar of rated capacity 320A, covered with PVC insulated sleeves including insulator, nuts, bolts, etc. with complete connection- 01Set (3P+N) [b] Incoming: [i] 250A, 415V, 50Hz, AC-31A, FP automatic power transfer switch (ACSO ATS 7000 series) with complete protection, time based breaking capacity 42kA for 50ms-01No. [ii] LED phase indicators (Red, Yellow, Blue)- 01Set [iii] Power Measurement Device with Class 1 accuracy, complying to IEC 62053- 22, 64 samples/cycle, 31st harmonic analysis, RS485, calibration LED, third party accuracy test certificate - 03Nos.

[c] Outgoing: [i] 160A, 415V, Ics = Icu = 25kA, 50Hz, FP MCCB with adjustable overload settings (0.36- ` X In) & tr = 0.5 - 16sec, adjustable short-circuit settings (1.5-10xIr), adjustable earth- fault settings (0.2- 1 X In), current limiting type double break roto active type, instanteneous protection and microprocessor based trip unit- 01No. [ii] 32A, 10kA, 415V, 50Hz FP MCB (c -curve)- 05Nos. [iii] 32A, 10kA, 230V, 5 Hz SPN MCB (c -curve)- 01No. [iv] LED phase indicators (Red, Yellow, Blue)- 05Sets [v] Cl 1.0 multi-function meter capable of measuring V, A, F, PF, W/VA, Wh/VAh, Runhrs. Onhrs & interupts- 05Nos.

Notes: [i] The Panel shall be completely Ethernet communication ready to communicate with Energy Management System & shall be Web based application in-built [ii] 06Nos. of ON/OFF/trip status and operations counters as well as multi-function meters shall be wired to Ethernet Gateway part of the panel

Supply, installation, testing and commissioning of ISO 50001: 2018 certified 'Energy Management System' complete all as specified and as directed as detailed hereinbelow: Make: Schneider, ABB, Siemens

(a) ISO 50001, ISO 50002 & ISO 50006, cybersecurity standard IEC62443 SL1 at the component level: IEC62443-4-1 and IEC62443-4-2 certified Power Monitoring and Energy software with builtin in SQL server standard edition, 01 Engineering Client & 03 Web Clients to view across the facility, OPC Client enabled User configurable inbuit dashboard Capability during runtime, Standard reports plus customisale reporting capability to configure total 120 devices. Database: SQL Server 2016 Or 2017 Standard/Enterprise Edition. Flexibility for the operator to create engaging dashboard displays of the power monitoring system information and easily share information with anyone in the facility. Software should have the capability to get advance power quality data thru ION technology to get wave forms, Harmonics compliance (IEEE519-1992) reports, Plot PQ events on an ITIC/CBEMA curve and get disturbance direction detection from ION compatible devices

(b) Protocol Converter RS 485 to Modbus TCP , POE, Dual Ethernet port installed in cabinet to accomodate Converter, 24V DC Power supplies, 4 port Ethernet TCP/IP unmanaged switch (Shielded RJ45 copper cable connection type, Supply voltage 24V DC, LED for power supply and per channel copper port activity, CE marking Ethenet switch) and necessary protection MCBs

(c) Ethernet Patch Cable of 3m length

(d) Cat 5E Cable LAN U/UTP 2x4P 300m length

(e) Cat 5E RJ45 connector

(f) 10 port Ethernet network Switch

(g) IT cabinet to accomodate Network Switch and power supplies and necessary protection MCBs

Dell Precision Workstation (Server for monitoring and reporting) With Dell 22 Monitor | E2417H 21.5" Intel(R) Xeon(R) Processor E3-12xx (6 core) 24GB RAM 1TB 3.5inch SATA (7,200 Rpm) Hard Drive x 1 16X Half Height DVD +/- RW x 1 Intel XEON Processor Label x 1 NVIDIA(R) Quadro(R) K620 2GB (DP, DL-DVII) (1 DP to SL-DVI adapter) x 1 External Speaker Not Included x 1 1Gbit NIC add-in card (PCIe- Intel) x 1 No Wireless LAN x 1 Dell Optical Mouse MS116 Black x 1 Dell Multimedia Keyboard KB216 Black (US International - QWERTY) x 1 Windows 10 Pro (64bit) English x 1 Windows 10 Pro OS Recovery 64bit - DVD x 1

Antivirus Quick heal Server Edition with 3 years Subscription # Limited Warranty: Initial Year (NBD) x 1 # Limited Warranty: Initial Year (POW) x 1 ## Onsite Service Yr 2-3 x 1 3Yr Onsite Service x 1 Note: Make Dell or equivalent as approved

1kVA UPS with 30minute back-up having single input and output, inbuilt SMF batteries and required accessories Make: Aplab/ Sukam / Luminous

Commissioning of approx 150 devices for New server. Prepration of Customised Power reports. Auto Report Generation, customised graphics development, configration of line diagram. Dashboard prepration online Trends. Alarm and Events generation, etc.

S&F 45W LED street light including LED having high efficiency long life LED module with SMD LED package mounted on MCPCB with high LED efficacy of >100 lumen/W, integral SMPS based constant current electronic LED driver with THD<10%, surge voltage protection and other safety tests as per IS: 15885 (Part-2/Sec-13): 2012, IP 66 protection, high effiency polycarbonate cover with integrated lens housed in pressure die-cast aluminium alloy heat sink for effective thermal management, sturdiness, excellent corrosion resistance, separate optical and control gear compartment & top opening for easy maintenance, suitable for side entry, pole mounting with bracket arm OD 35mm to 42mm including 45W LED bulb, necessary electrical connection to the fixture with 3 core flexible copper conductor cable of appropriate size and 1.5m long bracket, having 40mm diameter light grade GI pipe, including GI clamps, nuts, bolts & washers with two coats of synthetic enemal paint over a coat of red oxide primer complete all as specified and as directed Make: Bajaj Cat-Part No. 169799 BRTFG 45W LED or equivalent model of Philips / Wipro / Havells

S&F weather- proof PVC junction box of size 250x200x100mm, having IP 65 protection for outdoor installation fixed with 4 way bakelite cable terminals including 03Nos. of polymide gland with check nut (M-32- 3Nos.) fixed on poles with flat aluminium clamps of size 20x3mm, nuts, bolts, washers, etc. complete all as specified and as directed Make: Sintex Cat-Part No. GS-JB-2817 or equivalent model of Hensel / National

Supply, installation, testing and commissioning of intelligent street light control (ATSC) suitable for 6kW maximum load, wall/pole mounted, having built-in networking support, built-in astronomical timer, 32A TP contactor, 40A TPN MCB housed in 3.15mm thick powder CRCA sheet housing all complete as specified and as directed Make: Havells Cat-Part No. IHXTS03060 or equivalent model of Schneider / Legrand

Demolition & Dismantling

Dismantling cudappah stone slab partition fixed with cement mortar and disposing off

Dismantling and taking down HDPE / PVC water storage tanks of 1000litres capacity including all lifting and lowering equipments and disposing off

Dismantling and taking down HDPE / PVC water storage tanks of 2000litres capacity including all lifting and lowering equipments and disposing off

Dismantling and taking down HDPE / PVC water storage tanks of 3000litres capacity including all lifting and lowering equipments and disposing off

Taking down mirrors of any type and in any position and disposing off

Disconnecting from water mains, plugging off and dismantling low level PVC flushing cisterns and disposing off

Taking off short body 15mm dia bib taps or stop valves of any type and in any position and disposing off

Disconnecting from water mains, plugging off and dismantling vitreous China wash basins and disposing off

Disconnecting from outlets and water mains, plugging off and dismantling vitreous China urinals bowl type of any size and disposing off

Disconnecting from water mains, plugging off and dismantling satainless steel kitchen sink of any type with fittings and disposing off

Removing debris and rubbish or excavated materials (rocks / concrete, etc.) including all necessary cartage to a distance exceeding 15km but not exceeding 30km outside MD land

Taking down copper / aluminium point wiring (light, fan, socket or power) including fixture and fittings viz. switches, ceiling roses, light fittings, pendants, regulators, sockets, etc. and disposing off complete all as specified and as directed

Taking down DB with MCBs and disposing off complete all as specified and as directed

Taking up or down steel water tubing 25 to 50mm bore and connections and disposing off complete all as specified and as directed

Taking down unserviceable tube light fittings of any type from walls / ceilings, etc. and disposing off

Taking up / down unserviceable cables of size 6sqmm to 50sqmm, any type, from walls / ceilings / floors, etc. and disposing off

Disconnecting and taking down unserviceable ceiling fans, any type and depositing in MES store yard including cartage, etc.

Disconnecting and taking down unserviceable exhaust fans, any type and depositing in MES store yard including cartage, etc.

Taking down unserviceable ceiling roses, fan regulators, etc. of any type from walls / ceilings, etc. and disposing off

Taking down unserviceable sockets of any type and capacity from walls / ceilings, etc. and disposing off

Disconnecting and taking down unserviceable flood light fittings any type, 400W capacity and disposing off

Disconnecting and taking down unserviceable flood light fittings any type, 400W capacity and disposing off

Disconnecting and taking down unserviceable electric energy meters of any capacity and depositing in MES store yard including cartage, etc.

Rds Project ltd.

NILA INFRASTRUCTURES LIMITED

IRON TRIANGLE LIMITED

SPG Infraprojects Private Limited

Varindera Constructions Limited