Construction of Seismic Station and Miscellaneous Civil works at Mount Abu, Rajasthan.

Amount

From 0.00 to 1.50 m depth from Average Ground Level

From 1.50 to 3.00 m depth from Average Ground Level

From 0.00 to 1.50 m depth from Average Ground Level

From 1.50 to 3.00 m depth from Average Ground Level

From 0.00 m to 1.50 m below to average G.L.

From 0.00 to 1.50 m depth from Average Ground Level

From 1.50 to 3.00 m depth from Average Ground Level

Lead charges for lead soil upto 2 KM, by mechanical transport including loading, unloading, stacking / levelling etc. Note: The rates in respect of Item No.5 is applicable for the NET Quantities arrived at after making deductions for voids @ 20% in respect of soil, @ 50% in respect of Rock and @ 30% in respect of Debris from the corresponding Stack / Truck measurements. -Soil/Rock

Providing and laying in position cement concrete of 1:3:6 (1 cement, 3 crushed sand, 6 graded stone aggregate of maximum size 20 mm) including consolidation, finishing, curing etc. complete as per specificationsand drawings but excluding the cost of Form work shuttering, centering Complete at all levels

Providing and laying in position cement concrete of 1:2:4 (1 cement, 2 crushed sand, 4 graded stone aggregate of nominal size 20 mm) including consolidation, finishing, curing etc. complete as per specification and drawings but excluding the cost of Formwork shuttering, centering and steel reinforcement at all Levels

Providing and laying in position Reinforced Cement Concrete (RCC) of grade M-30 using 20mm maximum size aggregates and crushed sand of approved quality including admixtures of approved brand and quality (plasticiser or super plasticiser) if required, including weigh batching, mechanical mixing, transporting, placing, vibrating, consolidation, finishing, curing etc. complete but excluding the cost of centering, shuttering and reinforcement complete as per specifications up to Plinth Level.

Extra for RCC all grades in super structure up to 20.00 metre height

Extra for RCC Using Ready Mix Concrete from outside project area including transporting and pumping from approved batching plants .

Providing , centering ,shuttering Form work using PVC film faced plywood to get a neat form finish surface for all types of structures including necessary strutting, proping, staging, supports etc and deshuttering the same after the specified time all as per drawings, specifications and as directed by the Engineer-in-charge at all levels

For Sub Structure

For Super Structure

Providing wood work in frames of doors, windows, clear story openings and other frames, wrought framed and fixed in position of required size and shape including sawing, jointing,making rebates for shutters, making grooves as shown in the drawings, finishing the surfaces to the required finish all as per specifications and drawings including necessary MS hold fasts 40 mm X 3 mm thick, 200 mm long / with coach screws including protective painting to the suface that will come in contact with walls, joining materials, labour etc. complete all as per specifications and as directed by the Engineer-in-charge

Second class teak wood

Providing and fixing 35 mm thick flush door shutters conforming to IS : 2202 non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with internal teak wood lipping 25mm wide and fixing with 4 Nos of 125 mm long Stainless steel Hinges with S.S. wood screws complete.

Extra for providing and fixing flush doors with decorative veneering on both sides

Providing Structural steel work using angles, channels, joists and other sections, welded and / or bolted in built up sections for trusses , structural steel floors, frame works, monorails and other structures including supplying, cutting, welding, fabricating, hoisting, fixing in position, applying a priming coat of approved steel primer etc. complete all as per specifications, drawings and as directed by the Engineer in charge

Up to and including 300 mm Joists, 350 mm channels, and below sections using materials of approved manufacturers or approved equivalent quality or product meeting technical parameters. All test reports to be provided along with the supply of the materials Notes : 1. Structural steel confirming to IS 2062 shall be supplied from approved manufacturers from their own plants rolled from virgin materials to be procured directly or from their authorised dealers and test cerificate to be produced. 2. The contractor shall supply documentary evidence of purchase of steel, Test certificate from approved manufacturers and also third party testing from approved laboratories with out any extra cost.3. Welding weights, connections, bolts and nuts shall not be measured for payment but the cost of which shall be deemed to have been included in the rates.4. Welding Electrodes manufactured byapproved manufacturers or approved equivalent quality or product meeting technical parameters of specified suitable grade only shall be used 5. Holes to be drilled only by Drilling machines and gas cutting of holes are not permitted .6. Rate inclusive of all consumables like GAS, welding electrodes and tools and tackles etc.

Provding and constructing brick work in Cement mortar using standard bricks of approved class/ quality, make or brand in foundation and plinth including curing, raking out joints, simultaneous pointing below plinth level if specified, complete as per drawings, specifications and as directed by the Engineer-in-charge

Brick work in C.M 1:4 using crushed sand.

Brickwork in super structure with standard bricks in C.M 1:4 using crushed Sand

Providing and constructing Random Rubble masonry using approved Rubble stone in foundation and plinth in C.M 1:6 (using crushed sand) including raking out joints or simultaneous flush pointing below ground level / plinth level, curing etc. complete as per drawings and specifications.

Providing Raised and cut pointing on stone with cement moratr 1:3 using river sand as per specifications and as directed at site by the Engineer-in-charge

Providing and laying minimum 25 mm thick uniform shade Kotah stone flooring over 20 mm thick (Avearge) base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing in minimum three levels to obtain mirror polish complete with base cement mortar 1:4 (using crushed sand) all as per specifications, patterns and drawings complete.

Providing and Laying Minimum 25/30 mm thick uniform shade Kotah stone treads and risers of steps, skirting,window sills in single length up to 2.00 metres length slab dado and pillars laid on 12 mm thick (average) cement mortar 1:3 (using crushed sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing to obtain mirror finish complete as per specifications, drawings and as directed by the Engineer-in-charge

Minimum 30 mm thick both side polished cuddapah slab/local approved stone for platform vertical supports including chasing the walls , making alright, complete as per drawings & as directed at site by the Engineer-in-charge.

Providing and fixing aluminium aldrops of size 250 X 16 mm ISI marked anodised transparent or dyed to requried colour or shade with necessary screws, bolting from rear side complete as per specifications and as directed by the Engineer-in-charge

Providing and fixing anodised aluminium tower bolts of size 250 X 12 mm ISI marked of approved make, transparent or dyed to requried colour or shade with necessary screws etc.

Providing and fixing brass mortise latch and lock of approved make with 6 levers and a pair of lever Brass handles with necessary screws etc complete suitable for fixing in wooden / steel/ FRP/ doors as per specifications.

Providing and fixing aluminium handles 175 mm long Inner grip 125 mm with 12 mm dia rod plate type BOW handles ISI marked of approved make, anodised transparent or dyed to req. colour or shade with necessary screws etc. complete.

Providing and fixing anodized aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections / Z sections and other sections of approved make conforming to IS 733 and IS 1285 fixed with rawl plugs and screws or with fixing clips or with expansion hold fastners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC / neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically whereever required including cleat angle, aluminium snap beading for glazing / panelling, C.P brass / stainless screws all complete as per drawings and and directions of Engineer-in-charge including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of PVC / neoprene gasket required filling the gaps using silicon grout sealent etc. (fittings glazing and panelling shall be paid for separately)

Anodised Aluminium sections (Minimum anodizing thickness of 15 micron)

Providing and fixing glazing in aluminium doors, window, ventilator shutters and partitions etc with PVC / Neoprene gasket etc. complete as per the architectural drawings and directions of the Engineer-in-charge (Cost of snap beading shall be paid in basic item)

With clear float glass panes of 5.00 mm thickness

With tinted colour float glass panes of 5.0 mm thickness

Providing and fixing stainless steel (SS 304 Grade) adjustable friction windows stays of approved quality with necessary stainless steel screws to the side hung windows as per specifications and as directed by the Engineer-in-charge

Providing and fixing single point lock cum handle for aluminium openable windows / top hung shutters as per cat No. SPL002 Right of GEETAVIN make or approved equivalent quality and make complete all as per specifications and as directed by the Engineer-in-charge

Providing and fixing following sizes of Aluminium Louver sets without Glasss of make approved by EIC with necessary screws etc. complete. as per specifications and as directedb by the Engineer-in-Charge

Aluminium Louver set- without glass-5 blades- 469 mm wide .40 mm height

Providing 15 mm thick Internal plaster in cement mortar 1:4 without cement punning (using Crushed Sand) finished smooth, including sieving of sand to required fineness, preparation of the surface, scaffolding, curing all as per specifications, drawings and as directed at site complete.

Extra for cement punning for all types of mixes complete all as per specifications and as directed

Providing 20 mm thick External plastering in two coats under layer 12 mm thick with C.M 1:4 (using crushed sand) finished with a top layer 8 mm thick in C. M 1:3 (using crushed sand) including approved water proofing compound @ 2% by weight of cement or as per manufacturer's specifications, sieving of sand to required fineness, scaffolding up to 10 metres height, finishing, curing etc. complete as per specifications. and as directed by the Engineer-in-charge

Providing , painting and finishing walls with two coats of exterior emulusion paint of approved make on sand face plaster/ plain plaster & concrete of required shade over new work including base coat of water proofing cement paint, preparation of the surfaces, scaffolding complete. as per specifications and as directed by the Engineer-in-charge.

On rough cast Plaster surfaces

Providing and Painting two coats of synthetic enamel paint on Steel Surfaces of approved brand and manufacture to give an even shade without primer coat.including preparation of the surfaces, scaffolding complete. as per specifications and as directed by the Engineer-in-charge

Providing and painting TWO coats of synthetic enamel paint on new wooden surfaces of approved brand and manufacturer of required colour to give an even shade over an under coat of suitable shade primer of approved brand and manufacturer including preparation of the surfaces, scaffolding complete. as per specifications and as directed by the Engineer-in-charge

Providing, laying , jointing, fixing and testing heavy quality ( (ISI Marked C-Class) Galvanised Iron pipes and ISI marked fittings like, tees, elbows, bends, unions, nipples,reducers etc. as required for the work, including testing the pipes and fittings for 10.00 Kg / Sq.Cm hydralic pressure with a minimum period of two hours duration with clean water, including cutting , threading, jointing with hemp yarn, white lead, jointing teflon tape, chasing walls and making good by filling with concrete 1:3:6, complete all as per specifications and drawings, including two coats of anti corrosive bitumastic paint, all as directed by the Engineer-in-charge. Pipes with ISI marked 'C' -Class heavy quality pipes of approved make.

20 mm dia G.I pipe

25 mm dia G.I pipe

Providing and fixing G.I. chicken mesh in the junctions of concrete & brick work / masonry or as directed by the Engineer in charge including cutting, fixing with nails in position before plastering complete all as directed by the Engineer-in-charge. (only area of the chicken mesh used alone will be measured)

Providing and fixing C.P brass Angle cock of heavy quality of specified / approved make, for wash basin inlet / flush cistern etc. as per specifications and as directed by the Engineer-in-charge

15 mm n.b CP brass Angle cock of approved make

Providing and constructioning Inspection chambers of Internal size clear dimention of 900 x 600 mm in 230 thick brick masonry with cement mortat 1:4 over a bed of 150 mm thick 1:4:8 cement concrete foundation, plastering with cement mortar 1:4 20 mm thick on inside, out side and all exposed sufaces finished with a floating coat of neat cement, brick corbelling at top to provide opening of 900 X 450 mm, embedding the frame and cover with CC 1:2:4 concrete, and fixing cast iron steps if necessary at 300mm intervals complete . Depth of chamber not exceeding 900 mm. (excavation, soling, cast iron cover and C.I steps will be paid separately under relevant item)

Providing, supplying, fixing in position, under floors or in walls centrifugally cast iron pipes including required specials like bends, tees, 'Y' collars, cowl etc for soil, waste and ventilation pipes conforming to IS.3989 of approved make including cost of jointing with spun yarn and molten lead of specified quantity, caulking the joints, including testing of pipes, painting with primer, fixing at walls with necessary approved type of clamps and brackets complete all as per drawings and specifications and as directed at site.

75 mm dia centrifugally cast (spun) iron socketed pipe as per IS:3989 using 0.90 kg lead / joint

Supplying and fixing Cast Iron Man hole or Cast Iron Steps cover of approved make and weight as specified in the drawings or as directed by the Engineer in charge.

Providing and fixing PTMT liquid soap container ( Prayag or approved Equivalent make) of standard shape with bracket of the same materials with snap fittings of approved quality and colour Complete all as directed by Engineer in charge.

Providing and fixing C.P Brass towel ring complete fixed to walls with 30 mm CP brass screws with concealed fitting arrangement of Jaquar make or approved equivalent all as directed by the project engineer.

Providing and fixing C.P brass towel rail of approved make 600 mm long complete fixed to walls with 30 mm CP brass screws with concealed fitting arrangement all as directed by the Engineer-in-charge.

Providing and fixing 6 mm thick mirrors of size 600 x 450 mm of approved make with bevelled edges complete with 6 mm thick asbestos sheet back ground fixed to walls with C.P. brass screws and concealed washers complete. all as per specifications and as directed by the Engineer-in-charge .

Supplying and filling brick bats of size 40 mm to 75 mm in Soak pit as directed by the Engineer in charge

Dismantling plain cement concrete manually / by mechanical means carefully without damaging adjacent structures including disposal of debris within 200 m lead as per direction of Engineer-in-charge

Dismantling of RCC works carefully manually without damaging adjacent structures excluding cutting of reinforcement including stacking of steel reinforcement bars and disposal of unserviceable materials within 200 m lead as per direction of Engineer-in-charge

Demolishing Stone rubble masonry (In cement mortar) manually / by mechanical means carefully without damaging adjacent structures including stacking of serviceable materials and disposal of unserviceable materials within 100 m lead as per direction of Engineer-in-charge

Dismantling steel work in single sections including dismantling and stacking within 100 m lead In R.S Joists, Angles etc.

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 100 m lead For thickness of tiles above 25 mm and up to 40 mm

Providing and fixing G.M / brass ferrule in existing water main lines of specified dia and making connections including drilling / boring complete all as directed by the Engineer-in-charge

20 mm Ferrule

Providing and grouting the joints of rubble stone pitching with cement mortar 1:3 and pointing the surfaces as directed complete as directed by the Engineer-in-charge

Providing and fixing dry stone pitching 22.5 cm thick laid in required profile with hammer dressed stones having no side less than 15 cm, with minimum depth of 20 cm including preparing the bedding surface etc. all complete as directed by the Engineer-in-charge

Providing and fixing concertina barbed tape coil of follwoing dia. made from M.S galvanized ribbon tape of 0.5 mm thickness, 19 mm width stretching the coil to 9 m approximate, fixing the coil with clips between "Y" armed and MS angle posts 2.44 m high from ground level, including supplying and fixing MS galvanized clips etc. complete as per manufacturer's specification and including painting by dipping method the concrtina tape coil with two coats of synthetic enamel paint of approved shade and make over a coat of approved primer at fabrication shop, before bringing the material to the site and fixing in position etc. complete as directed by the Engineer-in-charge.

450 mm Dia Concertina coils

Supplying & fixing in position 2 ply, 12 gauge, 4 spikes at100 mm c/c G.I. barbed wire to M.S. angles/RCC wooden posts including providing necessary scaffolding, supplying & fixing necessary 'J' hooks, bolts, nuts, washers, staples as required etc. complete as per metric length of wire.

Providing and fixing GI chain link fabric fencing Made of GI wire of dia 4 mm of required width in mesh size 50 x 50 mm including strengthening with 2mm dia wire or nuts, bolts and washers as requeid complete as per direction of Engineer-in-charge.

Providing & fixing in position FAN HOOK with 16 mm dia. m.s. for bar including bending to shape, grouting with C.C. 1:2:4, painting with two coats of anti corrosive paint etc. complete.

Supplying , cutting to shape and fixing specified diameter UPVC pipes as per IS 4985 in RR Masonry/ RCC walls for weep holes complete all as per drawings and as specified at site.

110 mm dia UPVC Pipes

Providing and fixing heavy quality stainless steel / C.P brass grating of approved equvalent make as specified for floor traps / nahani traps all as directed by the Engineer-in-charge

SS grating 125 mm dia

Providing and fixing PVC rain water pipes conforming to relevant IS type B and PVC SWR fittings & specials conforming to relevant IS including jointing with seal ring / With PVC solvent adhesive including fixing in walls using clamps etc complete all as per drawings, specifications and as directed by the Engineer-in-charge

SWR PIPE 110 mm O/D

Supplying & installing SS wire-mesh/Mosquito net to shutters of windows with necessary SS screws, beading of aluminium and cut the surplus SS wire mesh and make it smooth in functional point of view etc all complete as per approved shop drawings and specifications or directed by Project Engineer.

Providing and fixing hand rail using 304 grade Stainless Steel pipes/Bars etc of approved size and make and quality by welding, mirror / matt polishing, fixing at site etc. for balcony railing & staircases railing including special sections as per drawings, specifications. complete as directed by the Engineer-in-charge

Supplying & installing of Electrical Items of As per Drawings attached herewith with wiring with earthing etc as approved make or as directed by Engineer in Charge etc Complete checking testing commissioning etc in all respect on functional ground. 1. Exhaust Fan 2. Ceiling fan, Points of 5 MP / board cover plate as per requirement etc complete. 3. PVC conduits for Concealed as per requirement. 4. Lightening arrester.5. Wiring of all points with copper earthing 6. Earth pit two nos near by area and their connection from constructed lab as specification etc.. as per drawing or as directed by Project Engineer.