SPECIAL REPAIR TO BLDG NO. ET-248 AND ET-249 AT CHANGSARI AND OTHER SANCTIONED WORKS AT RANGIA AND CHANGSARI MILITARY STATION UNDER GE RANGIA

Amount

Dismantling Unframed timber scantlings 40 Sqcm and over in section and in any position complete all as specified and as directed by Engineer-in-charge.

M&L for 2nd class hardwood in scantling wrought timber unframed and fixed complete all as specified and as directed by Engineer-in-charge.

Fixing only for 2nd class hardwood in scantling wrought timber unframed and fixed complete all as specified and as directed by Engineer-in-charge.

S&F Mild steel work in hand rails, wind ties, posts and struts in fencing screwed or welded to shape as directed, including all necessary drilling, bolting or riveting etc., and similar works complete all as specified and as directed by Engineer-in-charge.

M&L for brick work with sub-class `B' bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified and as directed by Engineer-in-charge.

M&L for G.I. Wire netting 0.9 mm dia and 12 mm mesh lathing to wood or metal studding, joists, etc., in walls, ceilings, stanchions, beams, etc., including all laps, cutting and waste complete all as specified and as directed by Engineer-in-charge.

M&L for rendering 15 mm thick on fair faces of brick work or one side of lathing in cement mortar 1:4, surface finished even and smooth without using extra cement complete all as specified and as directed by Engineer-in-charge.

M&L for rendering 10 mm thick on other than fair faces of brick work or on other side of lathing in cement mortar 1:6 , surface finished even and smooth without using extra cement complete all as specified and as directed by Engineer-in-charge.

Dismantling of unframed fillets, rails, posts, rafters, purlins etc., under 40 Sqcm in section complete all as specified and as directed by Engineer-in-charge.

S&F second class hard wood plain wrought fillets square, rectangular or triangular in section, bull nosed splayed chamfered or rounded on one edge or face sectional area exceeding 3 and not exceeding 6 Sqcm fixed with screws complete all as specified and as directed by Engineer-in-charge.

Dismantling of wall and ceiling boards (Fibre, pulp, insulation etc) of any thickness, including cover fillets complete all as specified and as directed by Engineer-in-charge.

S&F exposed GI powder coated snap grid frame of false ceiling 600 x 600 mm size of wall angle 25 x 25 x 0.30 mm size cross tee 22 x 35 x 0.60 mm with 4mm dia GI suspender fixed to roof slabs by means of ceiling cleats made out of GI flat 40 x 3 mm including supply and fixing of 4 mm thick E - board in false ceiling including fixing arrangement from roof and applying three coats of white wash on exposed surfaces all as specified and directed. complete all as specified and as directed by Engineer-in-charge.

M&L for preparing new plastered surface and applying two coats of distemper oil emulsion on wall surfaces including chalk whitening preparatory to distempering complete all as specified and as directed by Engineer-in-charge.

M&L for preparing new plastered surfaces and applying two coats of cement base paint on surfaces of walls including primer complete all as specified and as directed by Engineer-in-charge.

M&L for preparing surfaces of wood and wood based materials, new or old of any description and girth, not otherwise described and treated with two coats of creosote oil complete all as specified and as directed by Engineer-in-charge.

M&L for preparation of newly untreated wood or wood base surfaces of any description, not exceeding 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed by Engineer-in-charge.

Dismantling Asbestos Cement (Corrugated, Semi corrugated etc.) sheets in roof coverings etc. complete all as specified and as directed by Engineer-in-charge.

S&F pre-painted gavalume aluminium zinc coating GI based corrugated or semi corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self tapping screws complete all as per specified and as directed by Engineer-in-charge.

S&F pre-painted gavalume aluminium zinc coating GI based Plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self tapping screws complete all as per specified and as directed by Engineer-in-charge.

Demolition of cement concrete (unreinforced) in ground floors and pavings not exc. 15 cm thickness (below or above ground level) complete all as specified and as directed by Engineer-in-charge.

M&L 75 mm thick Cement concrete type C-2, 1:3:6 (using 40 mm graded stone aggregate) in footpath / hardstanding / pavings / plinth protections, finished even and smooth using extra cement incl spike rolling to making impression of expended metal, while the concrete is green complete all as specified and as directed by Engineer-in-charge.

S&F Coloured non skid ceramic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or Coloured cement to match over 15 mm thick screed bed or bedding layers in CM 1:4, complete all as per specified and as directed by Engineer-in-charge.

M&L glazed ceramic tiles (coloured) of size 300x200x7 mm thick on vertical surfaces such as dados, skirting, etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including backing 10 mm thick in CM 1:4 complete all as per specified and as directed by Engineer-in-charge.

Taking down shutters of any description not exceeding 1 Sqm each complete all as specified and as directed by Engineer-in-charge.

Taking down shutters of any description exceeding 1 Sqm but not exceeding 2 Sqm each complete all as specified and as directed by Engineer-in-charge.

S&F 30 mm thick Second class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc., without sash bars, edges of framing plain, chamferesd or rounded, fitted with cut and mitred beads for securing glass etc., as specified in SSR Pt I Section 8, clause 8.24 (b) and as directed by Engineer-in-charge.

S&F 35 mm thick second class hardwood kiln seasoned and chemically pressure treated plain framed panelled shutter (Two panel) with lock rail and panel of 10 mm bison panel as specified in SSR part I section & clause 8.24 (a) complete all as specified and as directed by Engineer-in-charge.

S&F 3 mm thick sheet glass, ordinary quality in squares not exceeding 0.5 Sqm in each pane fixed with cut & mitred beads complete all as specified and as directed by Engineer-in-charge.

S&F stainless steel wire cloth, 0.56 mm dia of wire and average width of aperture 1.18 mm and fixed with tinned stacks, or galvanized wire staples complete all as specified and as directed by Engineer-in-charge.

S&F 75 mm long Aluminium, anodised, barrel tower bolts of extruded section complete all as specified and as directed by Engineer-in-charge.

S&F 100 mm long Aluminium, anodised, barrel tower bolts of extruded section complete all as specified and as directed by Engineer-in-charge.

S&F 75 mm long extruded Aluminium alloy handles, fabricated type, anodised complete all as specified and as directed by Engineer-in-charge.

S&F 100 mm long extruded Aluminium alloy handles, fabricated type, anodised complete all as specified and as directed by Engineer-in-charge.

S&F 300 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast Aluminium alloy complete all as specified and as directed by Engineer-in-charge.

S&F 75 mm long extruded Aluminium alloy anodised butt hinges with galvanized mild steel hinge pin type C-21 complete all as specified and as directed by Engineer-in-charge.

S&F 100 mm long extruded Aluminium alloy anodised butt hinges with galvanized mild steel hinge pin type C-21 complete all as specified and as directed by Engineer-in-charge.

Demolition of brick work built in any cement mortar complete all as specified and as directed by Engineer-in-charge.

Demolition of reed lathing single or double including battens and plaster or chicken wire lathing complete all as specified and as directed by Engineer-in-charge.

Taking down cement plaster on brick wall of any description, including raking out joints, hacking for key, scrubbing down with water etc. complete all as specified and as directed by Engineer-in-charge.

M&L rendering 15mm thick on other than fair faces of brick or concrete surfaces in cement mortar 1:6 to be finished fair & even without using extra cement complete all as specified and as directed by Engineer-in-charge.

M&L rendering 15mm thick in two layers on fair faces of brick or concrete surfaces or on one side of lathing in cement mortar 1:4 to be finished fair & even without using extra cement using water proofing compound complete all as specified and as directed by Engineer-in-charge.

Supply only integral water proofing compound confirming to IS complete all as per specified and as directed by Engineer-in-charge.

M&L 40 mm thick PCC (1:2:4) type B-1 (using 20 mm graded crushed stone aggregate) as in floor, finished even and smooth using extra cement complete all as specified and as directed by Engineer-in-charge.

S&F 38 mm glass dividing strip 3 mm thick and inserted in position conform to design complete all as specified and as directed by Engineer-in-charge.

M&L 75 mm thick Cement concrete type C-2, 1:3:6 (using 40 mm graded stone aggregate) as in footpath / hardstanding / pavings / plinth protections, complete all as specified and as directed by Engineer-in-charge.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided complete all as specified and as directed by Engineer-in-charge.

M&L for mild steel TMT bars of 6mm to 8mm dia, cut to length, bent to shape required including cranking bending spirally & binding with and in including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and as directed by Engineer-in-charge.

M&L precast cement concrete 1:2:4, type B1 (Using 20 mm graded crushed stone aggregate) in landings, cover slabs (for manholes etc.) shelves and similar articles with plain faces and set in cement mortar 1:4 complete all as specified and as directed by Engineer-in-charge.

S&F second class hard wood plain fillets in rectangular or triangular in section, clean swan secured with screws or beads having sectional area exc.13sqcm but not exc. 25 sqcm complete all as specified and as directed by Engineer-in-charge.

S&F second class hard wood plain fillets in rectangular tringular in section of sectional area exc. 6sqcm but not exc.13 sqcm complete all as specified and as directed by Engineer-in-charge.

Dismantling of timber boarding of any description fixed in any position with nails complete all as specified and as directed by Engineer-in-charge.

S&F 50 mm thick second class hard wood boarding with butt joints clean sawn fixed with nails in any situation (except flooring and skirting) complete all as specified and as directed by Engineer-in-charge.

S&F 20 mm thick planed both sides second class hard wood boarding with butt joints clean sawn fixed with nails in any situation (except flooring and skirting) complete all as specified and as directed by Engineer-in-charge.

S&F Gl frame work for seamless false ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre and grid of GI frame will be 60 x 60 cm to recieve E-board ceiling complete all as specified and as directed by Engineer-in-charge.

M&L 4 mm thick Non-Asbestos Cement Plain building boards, fixed to timber/ Aluminium frame work with screws in ceilings complete all as specified and as directed by Engineer-in-charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as per specified and as directed by Engineer-in-charge.

S&F 35 mm thick Flush shutters, solid core construction, with particle board core and plywood face panels, commercial type on both sides complete all as per specified and as directed by Engineer-in-charge.

S&F solid PVC door frame of size 50x47mm made out of 5 mm single side prelam PVC sheet used instead of plain colour PVC sheet and edges will be painted to match with prelam sheet, reinforced with MS square tube complete all as specified and as directed by Engineer-in-charge.

S&F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S tubes for top & bottom rails. M.S frame shall bw covered with heat moulded plain colour PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and botom rail on either side & as gap insert for tip rail & bottom rails; Panelling of plain colour PVC sheet to be fitted in the MS frame weloded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement complete all as specified and as directed by Engineer-in-charge.

S&F butt hinges 100 mm long medium weight, cold rolled mild steel complete all as per specified and as directed by Engineer-in-charge.

S&F butt hinges 75 mm long medium weight, cold rolled mild steel complete all as per specified and as directed by Engineer-in-charge.

S&F 125 mm long Aluminium, anodised, barrel tower bolts of extruded section complete all as per specified and as directed by Engineer-in-charge.

S&F 125 mm long extruded Aluminium alloy handles, fabricated type, anodised complete all as specified and as directed by Engineer-in-charge.

Taking up or down 15mm bore steel tubing and connections, including cleaning for refixing or removal from site complete all as per specified and as directed by Engineer-in-charge.

Taking up or down 20mm bore steel tubing and connections, including cleaning for refixing or removal from site complete all as per specified and as directed by Engineer-in-charge.

S&F 15 mm bore Galvanized Steel tubes, medium grade, with all fittings complete all as per specified and as directed by Engineer-in-charge.

S&F 20 mm bore Galvanized Steel tubes, medium grade, with all fittings complete all as per specified and as directed by Engineer-in-charge.

S&F in repair bib tap 15mm bore cast copper alloy chromium plated with crutch or butterfly handle, screwed down, screwed for iron plate or for brass ferrule complete all as per specified and as directed by Engineer-in-charge.

S&F in repair 15mm bore pillar tap, fancy type, cast copper alloy with capstin head CP screwed down high pressure with or without littered 'H' or 'C' with long screwed shank and fly nuts screwed for iron pipe complete all as per specified and as directed by Engineer-in-charge.

S&F in repair 15mm bore stop cock CP screwed down high pressure with crutch or butterfly handle screwed both end for iron pipe complete all as specified and as directed by Engineer-in-charge.

S&F in repair chromium plated shower rose 125 mm size with or without swivel joints, including fixing to steel pipe or union complete all as specified and as directed by Engineer-in-charge.

S&F in repair PVC 10 ltr capacity low level flushing cistern white with inlet ball valve float and braket and 32 mm bore PVC flush pipe complete all as specified and as directed by Engineer-in-charge.

S&F in repair grating round 100 mm size of PTMT (min weight 25 grms) complete all as specified and as directed by Engineer-in-charge.

S&F in repair 15mm dia PVC connection pipe with PTMT nuts of length 450mm complete all as specified and as directed by Engineer-in-charge.

S&F in repair Vitreous China wash down water closet pan 580 x 440 mm (Pedestal pattern) white complete incl seat and cover, flush pipe incl all joints complete all as specified and as directed by Engineer-in-charge.

S&F in repair 40 mm bore dia of discharge pipe waste coupling of PTMT (60 gm weight) (half or full threaded) complete all as specified and as directed by Engineer-in-charge.

S&F Vitreous China Ware Wash hand basin white, flat back of size 550 x 400 mm size (flat back or angle back type) including cutting for and pinning ends of brackets or erecting stand complete all as per specified and as directed by Engineer-in-charge.

M&L for preparation of new or previously untreated surfaces of wood and wood based surfaces of any description not other wise described of over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as per specified and as directed by Engineer-in-charge.

M&L for preparation of old or previously untreated wood and wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying one coat of synthetic enamel paint (Ordinary tint) over a coat of Pink primer complete all as per specified and as directed by Engineer-in-charge.

M&L for preparation of old or previously untreated wood and wood based surfaces of any description, not otherwise described, not exceeding over 10 cm width or girth and applying one coat of synthetic enamel paint (Ordinary tint) over a coat of Pink primer complete all as per specified and as directed by Engineer-in-charge.

M&L for preparation of old steel surfaces of any description not otherwise described over 10cm girth or width and applying one coat of synthetic enamel paint over a coat of pink primer complete all as per specified and as directed by Engineer-in-charge.

M&L for preparing newly plastered surfaces of walls and applying three coats of white wash complete all as per specified and as directed by Engineer-in-charge.

M&L for preparing old plastered surfaces of walls and applying one coat of white wash complete all as per specified and as directed by Engineer-in-charge.

M&L for 30 mm thick, 2nd class hard wood, plain, framed paneled shutters (any number of panels) with panels of timber flat on both side (feather edged) or of veneered particle board medium density, wood particle board with commercial face veneers etc complete all as per specified and as directed by Engineer-in-charge.

M&L for preparation of wood and wood based material, steel or iron work of any description or girth not otherwise described and treated with with tar or coal tar black paint complete all as per specified and as directed by Engineer-in-charge.

M&L for sanding newly tarred or painted surfaces with clean sharp sand complete all as per specified and as directed by Engineer-in-charge.

M&L for ATT at points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/hole by drilling 6mm dia holes at a downward angle of 45 drgee at 150 mm centre to centre and sealing the same complete all as per specified and as directed by Engineer-in-charge.

Taking down carefully aluminum/copper point wiring (light, fan, socket or power) complete incl fittings and fixtures such as switches, sockets, light fittings, ceiling rose, pendants, lamp holders, shade conical, regulators and removing all removed fittings and fixtures with wiring cable, battons, wooden boards etc from site and making good disturbed surfaces of walls, floors, ceiling etc all complete all as per specified and as directed by Engineer-in-charge.

M&L for point wiring with 1.5 sqmm size (nominal area) PVC insulated single core multi stranded copper conductor cable drawn into and incl PVC casing capping sleeves and caps of adequate width and length with all accessories and fittings like bends, elbow, crosses and PVC rectangular block with 3mm thick plastic laminated sheet cover as directed for mounting fittings etc like switches, sockets and fan regulator incl 1.5 sqmm size PVC insulated multistranded copper conductor cable as earth continuity conductor and connected to earth dolly for one light point controlled by one switch complete all as per specified and as directed by Engineer-in-charge.

All as per serial item no. 90 above but for one fan point controlled by one switch.

All as per serial item no. 90 above but for 3 pin socket combination 5 Amps on independent board.

All as per serial item no. 90 above but for 3 pin 5 amp socket 5 Amps on same board.

All as per serial item no. 90 above but with 4 sqmm (nominal area) cable with 4.00 sq mm size copper earth continuity conductor of green colour for 15 A socket outlet on independent boards .

All as per serial item no. 90 above but for one bell/buzzer point controlled by one bell push button.

All as per serial item no. 90 above but with 2.50 sqmm (nominal area) cable with 2.50 sq mm size copper earth continuity conductor of green colour for 15 A socket outlet on independent boards .

Supply and fix switch piano type 5 Amp single pole one way complete all as specified and as directed by Engineer-in-charge.

Supply and fix ceiling rose surface backelite three terminal complete all as specified and as directed by Engineer-in-charge.

S&F socket outlet 2in1, 3 Pin, 5 AMP flush type, complete all as specified and as directed by Engineer-in-charge.

S&F switch socket combination 3 pin, 05 Amps flush type complete all as specified and as directed by Engineer-in-charge.

S&F switch socket combination 5 pin, 05/16 Amps flush type with neon indicator complete all as specified and as directed by Engineer-in-charge.

S&F stepped type electronic fan regulator flush type on the existing phenolic laminated sheet etc. as reqd including necessary electric connection complete all as specified and as directed by Engineer-in-charge.

S&F LED tube light fitting, Wall mounted, extruded head dissipation & integrated with crystal glass LED tube (double side connection) 20 W LED (4ft), 230V, complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor of suitable size complete all as specified and as directed by Engineer-in-charge.

S&F 10 Watt bulk head fitting, environmental friendly, ultra modern, energy saving, surface mounted, decorative back-lit LED luminaire comprising of high brightness LEDs, IP66, complete all as specified and as directed by Engineer-in-charge.

Supply and fix lamp holder, PVC/Polycarbonate type with back plate including 15 watt LED bulb complete all as specified and as directed by Engineer-in-charge.

S&F in repair single pole & neutral 8 way DB with double door including taking down old unserviceable one, complete all as specified and as directed by Engineer-in-charge.

Supply and fix MCB SPN 240 Volts 40 Amps breaking capacity 10 KA rating complete all as specified and as directed by Engineer-in-charge.

Supply and fix MCB SP 240 Volts 6 to 32 Amps breaking capacity 10 KA rating complete all as specified and as directed by Engineer-in-charge.

M&L for sub main wiring two run of size 10 sqmm PVC insulated electric power cable (heavy duty) 1100 volts grade with stranded copper conductor with 10.0 sqmm PVC insulated copper conductor earth wire in casing caping of suitable size (two run of 10 sqmm cable and one of 10.0 sqmm wire and one run of PVC conduit / casing caping will be measured as one unit) complete all as specified and as directed by Engineer-in-charge.

S&F 1100 volts grade heavy duty cable PVC insulated and sheathed aluminum conductor in service connections suspended by insulating hangers not more than 1 Mtr apart including 4 mm suspension wire one twin core cable flat or circular of 16 Sqmm size with multistranded conductor including taking down old unserviceable existing cable complete all as specified and as directed by Engineer-in-charge.

M&L for earthing with Galvanised Iron Earth Plate Electrode 600X600X6mm size buried directly in Ground vertically at a depth not less than 2.25 METRE below Ground Level with the Top Edge of Earth Plate at a depth not less than 1.50 METRE below Ground Level connected to Galvinased earth lead wire 4.0mm dia by means of Bolts, Nuts, Check Nuts and Washers of Galvanised Steel, Earth Plate Electrode surrounded by a packed thickness of Char Coal or Coke Dust mixed with common Salt in alternate layers not exc. 150mm thick including Galvanised Iron Pipe 25mm Bore (dia) Light Grade, upto test points above the Floor Level of the Building situated including PCC Pit in Cement Concrete 1:3:6 (20mm Graded Stone Agg-regate) and RCC Cover of size 540X540X50 mm in RCC 1:2:4 (20mm Graded Stone Aggregate) einforced with and including 8.0mm dia TMT Bars @ 100mm centre to centre both ways including taking down old unserviceable one complete all as specified and as directed by Engineer-in-charge. NOTE:- (I) item includes the cost of 7.5 mtr length GI pipe for protection for GI earth wire. (ii) item rates includes the cost of 7.5 mtr earth lead GI earth wire. (iii) PCC pit shall be provided at least 500mm away from the pit and not on the earth pit itself and the extra cost of additional length of watering pipe, bends, elbow, etc. shall be deemed included in the unit rate.

S&F switch piano, flush type, single pole, one way, 15 Amps, 230 volts complete all as specified and as directed by Engineer-in-charge.

S&F socket outlet 2 in 1, 230 volts, flush type, 6 pin 5 and 15 Amp complete all as specified and as directed by Engineer-in-charge.

S&F bell push 5A, 230 Volts flush type complete all as specified and as directed by Engineer-in-charge.

S&F bell, AC, 230 volts, single pole fixed on pvc board of suitable size complete all as specified and as directed by Engineer-in-charge.

Supply and fix LED tube light fittings with regal batten for LED, wall mounted, extruded head dissipation & integrated with crystal gladd LED tube (single side connection) 22 W LED 4', 230 V complete with all accessories internally prewired and including connecting up with twin core twisted flexible copper conductor cable from ceiling rose to tube light fitting complete all as specified and as directed by Engineer-in-charge.

S&F 36 watt recess mounted high lumen output LED light fittings of size 2 ft X 2 ft for metallic false ceiling type armstrong/US gypsum or similar ceiling mounting system with concealed or exposed 'T' section complete all as specified and as directed by Engineer-in-charge.

Supply and fix angle lamp holder, PVC/Polycarbonate type with back plate complete all as specified and as directed by Engineer-in-charge.

S&F Cast iron/pressed steel terminal boxes 60mm deep for mounting mounting of DBs with 3mm thick plastic laminated sheet cover of size 300 mmX250 mm complete all as specified and as directed by Engineer-in-charge.

S&F in repair single pole & neutral 8 way DB with single door including taking down old unserviceable one, complete all as specified and as directed by Engineer-in-charge.

Supply and fix MCB SPN 240 Volts 6 to 32 Amps complete all as specified and as directed by Engineer-in-charge.

S&F in repair House service bracket(Hook type) complete with 3.0m long G.I pipe 40mm dia medium grade, two nos.90 degree bends, M.S hook and stay or guy including taking down old unserviceable one complete all as specified and as directed by Engineer-in-charge.

Taking down Ceiling Fan of any sweep and make by disconnecting electric connection, dismantling Blades, down rod and removing Ceiling Fan to MES STORE YARD OF AGE E/M RANGIA for Checking, complete all as specified and as directed by Engineer-in-charge.

M&L for Opening Stator of Ceiling Fan 1200mm Sweep Cleaning of Parts, replacement of Unserviceable Parts as ordered, Greasing of Moveable Parts, complete all as specified and as directed by Engineer-in-charge. NOTE : Unserviceable Parts viz burnt coil, Ball Bearing, Bush, Capacitor, etc. shall be Measured and Paid separately under respective Items as mentioned here-in-after.

M&L for re-winding the coil of ceiling fan 1200 mm sweep with Supper Enameled Copper Wire of same Gauge and same Weight with Insulation Paper, Varnishing and Heating, complete all as specified and as directed by Engineer-in-charge.

Re-assembleing the ceiling fan of any sweep after repaires and testing, complete all as specified and as directed by Engineer-in-charge.

Supply only Ball Bearing as approved suitable for Ceiling Fan of 1200mm Sweep, complete all as specified and as directed by Engineer-in-charge.

Supply only Fan Blades (Set of 3/4 blades as required at site) suitable for Ceiling Fan 1200mm Sweep of Make as required/ ordered at Site, complete all as specified and as directed by Engineer-in-charge.

Supply only gun metal bush of any size as per the existing, complete all as specified and as directed by Engineer-in-charge.

Hanging only Ceiling Fan of any sweep and make and connecting up electric connection from Ceiling Rose/Connector to Fan with flexible wire including replacing some minor unserviceable spares like canopy, rubber Reel, split pin, down rod etc., complete all as specified and as directed by Engineer-in-charge.

M & L for painting of ceiling fan of 1200 /1400 mm sweep with two coats of synthetic enamel paint over a one coat of red oxide primer after preparing the painting surface etc complete all as specified and as directed by Engineer-in-charge.

Supply and fix LED batten 4' with wide angle profile high lumen batten suitable for 20 Watt complete all as specified and as directed by Engineer-in-charge.

Supply and fix LED tube 20 W with single side connection suitable to fix in LED baten of 20 Watt complete all as specified and as directed by Engineer-in-charge.

S&F PVC terminal boxes 18 module for mounting mounting of DBs with 2 mm thick plastic laminated sheet cover complete all as specified and as directed by Engineer-in-charge.

Dismantling and lowering down of old rusted top plate/roof sheet made out of 3.15mm thick mild sheet from pressed steel water tank on 40 feet staging carefully without making any damage to other members after necessary unscrewing bolts, nuts, etc. complete all as specified and as directed by Engineer-in-charge.

Supply, errection, hoisting and fixing of mild steel top plate/roof sheet 3.15mm thick made to required shape and drilling necessary holes for fixing of bolts & nuts and fixed on existing pressed steel water tank on 40 feet staging including necessary wire mesh jaly as required complete all as specified and as directed by Engineer-in-charge.

Refixing of serviceable top plate obtained from serial item No. 135 after properly cleaning with the help of wire brush complete all as specified and as directed by Engineer-in-charge.

Dismantling and lowering down 5 mm thick pressed steel side plates of size 1.22m x 1.22m from pressed steel water tank on 40 feet staging, carefully without damage to other members after necessary unscrewing of bolts, nuts, washers etc including separating serviceable side plates of following thickness and kept in safe custody for reuse in the same work complete all as specified and as directed by Engineer-in-charge.

Dismantling and lowering down 6 mm thick pressed steel side plates of size 1.22m x 1.22m from pressed steel water tank on 40 feet staging, carefully without damage to other members after necessary unscrewing of bolts, nuts, washers etc including separating serviceable side plates of following thickness and kept in safe custody for reuse in the same work complete all as specified and as directed by Engineer-in-charge.

Supply, errection, hoisting and fixing of new pressed steel side plate of 1.22mx1.22m and 5 mm thick, made to required shape and drilling necessary holes for fixing of bolts and nuts in existing pressed steel water tank on 40 feet staging complete all as specified and as directed by Engineer-in-charge.

Supply, errection, hoisting and fixing of new pressed steel side plate of 1.22mx1.22m and 6 mm thick, made to required shape and drilling necessary holes for fixing of bolts and nuts in existing pressed steel water tank on 40 feet staging complete all as specified and as directed by Engineer-in-charge.

Fixing only old serviceable pressed steel side plate of size 1.22mx1.22m obtained from serial item No. 138 here-in-before of 5 mm thickness with nuts, bolts and washers in existing pressed steel water tank after proper cleaning with the help of wire brush on 40 feet staging complete all as specified and as directed by Engineer-in-charge.

Fixing only old serviceable pressed steel side plate of size 1.22mx1.22m obtained from serial item No. 139 here-in-before of 6 mm thickness with nuts, bolts and washers in existing pressed steel water tank after proper cleaning with the help of wire brush on 40 feet staging complete all as specified and as directed by Engineer-in-charge.

M&L for fixing water level indicator comprising of CI float oval type 250 mm dia at centre, MS pulley of 150 mm dia, mild steel indicators of suitable size permanently marked stranded stainless steel rope of 10mm dia and 03 m long including connection and accessories required for smooth functioning and testing on completion including dismantling unserviceable one complete all as specified and as directed by Engineer-in-charge.

Dismantling and lowering down mild steel tie bar made out of angle iron size 65mm x 65mm x 6mm and 2.00 metre long each from pressed steel water tank on 40 feet staging without any damage to other members with necessary unscrewing of bolts, nuts and washers complete all as specified and as directed by Engineer-in-charge.

Supply, errection, hoisting and fixing mild steel tie bars made out of angle iron of size 65mmx65mmx6mm and 3.00 metre long Each and drilling necessary holes for fixing of bolts & nuts in existing pressed steel water tank on 40 feet staging complete all as specified and as directed by Engineer-in-charge.

Fixing only serviceable tie bars obtained from serial item No 145 above duly cleaned complete all as specified and as directed by Engineer-in-charge.

Supply and fixing mild steel machine made nut and bolt 16-20 mm dia and not exceeding 5 cm long nuts and bolts with washers for fixing of steel plates, tie bars, etc. complete all as specified and as directed by Engineer-in-charge.

Supply and fixing mild steel machine made nut and bolt 11-15 mm dia and not exceeding 5 cm long nuts and bolts with washers for fixing of steel plates, tie bars, etc. complete all as specified and as directed by Engineer-in-charge.

Fixing only serviceable nuts, bolts and washers obtained from dismantled items for fixing of pressed steel plates, tie bar, roof sheets, etc. complete all as specified and as directed by Engineer-in-charge.

M&L for fixing leak proof materials comprising of lead wire, glass wool and black putty in existing pressed steel tanks to ensure water tightness after taking out old existing jointing materials by burning with blow lamps and cleaning and jointing surface complete all as specified and as directed by Engineer-in-charge.

Taking down carefully existing vertical 100mm bore GI pipe with all fittings (inner, outlet, washout pipes) from PS over head tank and refixed to water tanks after disconnecting the same from the tank and cleaning and removing all scale and dirt, etc. from inside of pipe, cleaning and removing the old screw threads and providing the new jointing materials and other fixing accessories (after carrying out necessary repair and painting of water tanks as stated under relevant items) complete all as specified and as directed by Engineer-in-charge.

Taking down unserviceable vertical pipes 100mm bore GI pipe with all fittings (inner, outlet, washout pipes) complete all as specified and as directed by Engineer-in-charge.

Suppply and fixing of medium grade GI Pipe of 100 mm dia (including all fittings) and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed by Engineer-in-charge.

M&L for preparation of painted Old steel surfaces (inside surfaces of water tank) by removing all foreign particals from steel surfaces and cleaning throughly the surfaces and complete drying the surfaces and applying one coat of black bituminous paint suitable for drinking purpose in pressed steel water tank on 40 feet staging complete all as specified and as directed by Engineer-in-charge.

M&L for preparation of new steel surfaces (inside surfaces of water tank) by removing all foreign particals from steel surfaces and cleaning throughly the surfaces and complete drying the surfaces and applying two coats of black bituminous paint suitable for drinking purpose in pressed steel water tank on 40 feet staging complete all as specified and as directed by Engineer-in-charge.

M&L for preparation of old steel surfaces of water tank (out side surfaces) and priming with red oxide primer and applying one coat of synthetic enamel paint of existing colour complete all as specified and as directed by Engineer-in-charge.

M&L for preparation of new steel surfaces of water tank (out side surfaces of replaced pressed steel sheets and tie bars and angle irons) and priming with red oxide primer and applying two coats of synthetic enamel paint of existing colour complete all as specified and as directed by Engineer-in-charge.

M & L for writing the letters "PS TANK CAP 45000 Ltrs" and " SAVE WATER" on the tank having 40 feet staging with white synthetic paint on front side and "MES" on other side. Size of letter shall not be less than 30 cm complete all as specified and as directed by Engineer-in-charge.

S&F in repair 150 mm bore sluice Valve cast iron body class PN-1 grade brass spindle both end flanged and GM valve sheet and iron wheel confirming to IS:14846 including all materials requried such as 3 mm thick rubber gasket, bolts, nuts, washer, ISI marked complete all as specified and as directed by Engineer-in-charge.

Supply, fixing, testing and commissioning of Servo Voltage stabilizer for automatic operation, three phase, naturally oil cooled, indoor type & designed for input variation between 300 V to 480 V with output voltage stabilized at 415 with accuracy ± 2.5% and speed of correction 8 Volts per second and of capacity 300 KVA complete all as specified in para 19.100A of MES SSR part-I, 2009 and all accessories as per manufacturer's recommendation complete all as specified and as directed by Engineer-in-charge.

Supply, fixing, testing and commissioning of Servo Voltage stabilizer for automatic operation, three phase, naturally oil cooled, indoor type & designed for input variation between 300 V to 480 V with output voltage stabilized at 415 with accuracy ± 2.5% and speed of correction 8 Volts per second and of capacity 250 KVA complete all as specified in para 19.100A of MES SSR part-I, 2009 and all accessories as per manufacturer's recommendation complete all as specified and as directed by Engineer-in-charge.

M&L for earthing complete with galvanised steel earth plate electrode 60×60cm×6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level, connected to galvanised iron strip 32×6mm as earthing lead by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 5 connected to earthing test point including testing on completion complete all as specified and as directed by Engineer-in-charge.

Supply, laying and testing of cable XLPE Insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminum conductor of size 300 sqmm 3.5 core complete all as specified and as directed by Engineer-in-charge. Note:- The contract sum shall be calculated by deducting the amount shown in Credit Schedule attached to this tender, from total amount of Schedule 'A'/BOQ.

RAJKAMAL ENTERPRISE

KAKWANI BUILDERS