REPAIR MAINT TO JOINERY GRILL, GLASS PANES WIRE MESH PLINTH PROTECTION AND OTHER B AND R WORKS AT AFS SULUR

Amount

SCHEDULE A BOQ

Repair to ends of chajjas/ parapets by removing old concrete, loose material ,& cleaning of the reinforcement and finishing the surface in cement mortar 1:3 , finished fair & even and making good with existing finishes all as specified and directed. Note: Rate quoted by the tenderer shall be deemed to inclusive of double steel scaffolding and water proofing compound.

Demolition of brick work masonry, built in cement mortar including all quoins, pillars etc., complete all as specified and directed.

Fly ash Brick work with sub-class `B' bricks, straight or curved on plan exceeding 6 M mean radius built in cement mortar 1:4 complete all as specified and directed.

Fly ash Brick work obtained from demolition of brick work on plan exceeding 6 M mean radius built in cement mortar 1:4 complete all as specified and directed.

Reinforced Cement Concrete Type B1 1:2:4 (using 20 mm graded granite stone aggregate) cast in situ in lintels up to 1.5 M span, cills and other similar bands, plinth courses, parapets, copings, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles and throating as directed including use and waste of form work complete all as specified and directed.

Deformed TMT steel bar of grade Fe-500/500D , 10 mm dia and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings no exceeding 15 cm thickness (below or above ground level) including removing demolition materials to out side MD land complete all as specified and directed.

Hard core of broken/crushed stone aggregate of gauge n.exc 63 mm deposited, spread and levelled in layers not exc 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

Taking down shutters of any description exc 1.0 Sq.m and n.exc 2.0 Sq.m each complete all as specified and directed.

Taking down Chowkats or frames with shutters(Without taking off shutters from the frames) exceeding 1.5 Sq. M each but n exc 4 sq.m each complete all as specified and directed.

Solid PVC door frame of size 50mmX47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube suppling & fixing in opening as per specificatioon and drawing

30mm thick Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers, edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); all as specified and directed.

Taking down shutters exc 1 sqm but n. exc 2.0 sqm and refixing in the same location complete all as specified and as directed.

Second class hard wood plain, solid, straight Chowkats and frames, wrought, framed, rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed.

Applying two coat of synthetic enamel paint over a coat of pink primer of any description over 10 cm width or girth including preparation of new wooden surfaces complete all as specified and directed.

Easing of door shutters for easy closing/opening and tightening of hinges or changing the position of hinges, adjustment of tower bolts, sliding bolts with new screws etc complete all as specified and directed by Engineer-in-Charge, Size of door upto 2 Sqm single leaf or double leaf.

Easing of window shutters, kitchen cupboard shutters, show case shutter drawers including fixing of screws adjusting handles, knobs tightening piano hinges including misc small adjustments complete all as specified and directed by Engineer-in-Charge, size of window upto 1.5 Sqm.

Resecuring without taking down chowkhats or frames but with shutters ( without taking off shutters from the frames) not exc 1.5 sqm each.

Resecuring without taking down chowkhats or frames but with shutters ( without taking off shutters from the frames) exc 1.5 sqm but n exc 4 sqm each.

100mm long Butt hinges medium weight cold rolled stainless steel, to wooden frame/welded to metal frame including taking down existing one complete all as specified and directed.

Butt hinges 75 mm long medium weight cold rolled stainless steel including taking down existing one complete all as specified and directed.

Vitrified Ceramic tiles 10 mm thick, dark shade (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including screed bed or bedding layer ,15 mm thick in Cement Mortar 1:6 including taking down existing tile and removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed. Note : (a) Vitrified tiles are classified under group B1a of the international Standard for ceramic tiles ISO: 13006. Tiles shall be hard, dense, impervious and frost resistant. Water absorption of tiles shall be less than 0.5% and flexural strength (Modulus of Rupture) shall be more than 35 N/Sqmm. (b) The manufacturer's test certificate and individual test certificate for tiles must be submitted for approval by the concerned authority prior to installation.

Vitrified Ceramic tiles 10 mm thick, dark shade (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, as in skirting/dado. etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including backing coat ,10 mm thick in Cement Mortar 1:3 including taking down existing tile and removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed. Note : (a) Vitrified tiles are classified under group B1a of the international Standard for ceramic tiles ISO: 13006. Tiles shall be hard, dense, impervious and frost resistant. Water absorption of tiles shall be less than 0.5% and flexural strength (Modulus of Rupture) shall be more than 35 N/Sqmm. (b) The manufacturer's test certificate and individual test certificate for tiles must be submitted for approval by the concerned authority prior to installation.

Clean sawn battens at 15 cm centres 2nd class hardwood having sectional area exc 15cm but not exc 25 Sqm cm including dismantling timber scantlings 40 sq. cm and over in section, in any position compete all as pecified and as directed

Rendering 15 mm thick in two layers on brick or concrete surfaces,first coat 10mm thick in cement mortar 1:4 and 2nd coat 5mm thick in cement mortar 1:4 mixed with water proofing compound as per manufacturer instructions finished even and smooth without using extra cement complete all as specified and directed. Note: (a) Water proofing compound shall be measured and paid seperately. (b) The unit rate quoted is deemed to included for Removing of accumulated earth of any width and depth upto 15 cm cleaning/cutting the grass with hand operated petrol/kerosene driven grass cutting machine and removing the grass waste around 3 m from plinth protection to outside MD land Note: Periodicity of cutting of grass shall be before commencement of work and after completion of repairs.

Supply Only integral water proofing compound complete all as specified and as directed. Make:-Dr. Fixit Pidi Proof and equivalent.

Applying two coats of cement based paint over and including a coat of primer and wall care putty, including preparation of new plastered wall surfaces of any description, complete all as specified.

Sheet glass, ordinary quality and glazing, 4 mm thick with oil putty in squares not exceeding 0.5 Sq. M in each pane including Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beadscomplete all as specified and directed.

Machine cut cudappah stone slab 20-25mm thick, laid over and including 15mm thick cement screed base in CM(1:4), laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

Rounding to edges of stone slabs one edge such as in steps cooking platform and other similar situations,etc complete

Arboart collection luxury vinyl planks of size 6'x36' (152.4mmx914.4mm) 7.25"x48" (184.mm x 1219.2mm) having an overall thickness of 2.00mm with an wear layer of 0.30mm thickness the fire resistance of which should be class I , as wall clading which is structurally stable, clean levelled dry and free from dust, dirt wax, grease or any other foriegn material with a water based adhesive, roled thereafter with a 560 Kg roller. Make Armstrong works Industries or equivalent as approved by GE (incl demolation of old wall panelling including suitable frame as directed by manufacturers/Enginer-in-Charge by providing with angles or tees with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angles, as necessary, gusset plates, riveting, etc. and dismantling existing one complete all as specified and as directed.

100mm thick, plain cement concrete (1:3:6), type C-2 (using 40 mm graded mechanically crushed stone aggregates), as in plinth protection/path/hardstanding including making joints @ 3.00 metre intervals and at each corner, the joint shall be filled with mastic filling (to full depth) comprising of one part heated hot blown bitumen 85/25 & two parts heated sand (by volume), surface finished even and smooth without using extra cement including demolition of cement concrete (unreinforced) in ground floors and pavings not exceeding 15 cm thickness and rubish material shall be disposal to out side MD land complete all as specified and as directed. Note :- The concrete shall be laid at a stretch not exceeding 3 metre in length and width of joint shall not be more than 12 mm.

75mm thick, plain cement concrete (1:3:6), type C-2 (using 40 mm graded mechanically crushed stone aggregates), laid in 1:20 slope as in plinth protection/path including making joints at 3.00 metre intervals and at each corner, the joint shall be filled with mastic filling (to full depth) comprising of one part heated hot blown bitumen 85/25 & two parts heated sand (by volume), surface finished even and smooth without using extra cement complete including demolition of cement concrete (unreinforced) in ground floors and pavings not exceeding 15 cm thickness and rubish material shall be disposal to out side MD land complete all as specified and as directed. Note :- The concrete shall be laid at a stretch not exceeding 3 metre in length and width of joint shall not be more than 12 mm.

Pre painted Coloured Galvalume roofing system sheet 0.50 mm thick having Zinc aluminum alloy coating AZ150 shall be as per IS:277/ASTM 1379 150 gsm/ sqm double ribbed trapezoidal profile steel sheet any colour having tensile strength of 550 Mpa as in Roof covering /cladding to wall fixed with self tapping screws including dismantling of existing roof sheet complete all as directed.

Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws including dismantling of existing roof sheetas specified

Note for Pre-painted coloured Galvalume roofing :-

(i) The manufacturer's test certificate and individual test certificate for the chemical and mechanical properties of sheet must be submitted for approval by the concerned authority prior to installation.

(ii) The contractor shall ensured that no leakages take place from the roof. The roofing shall be Coloured Galvalume roofing system (olive green colour or as approved by GE) with feed material manufactured from 0.50 mm Total coated thickness (TCT), minimum 550 MPa yield strength and shall conform to the physical specifications of IS: 2062 of 2011, coated with hot dip metallic Aluminium / Zinc alloy coating AZ150 as 150 gm/sq.mt total on both sides.

(iii) The painting shall be coloured baked enamel polyester with silicon coating of film thickness 25 microns nominal on the exposed face/exterior side and on the reverse side ( interior face) shall be white with 15 microns film thickness, over a coat of 5 micron nominal thickness Primer.

(iv) The contractor shall produce purchase vouchers for each lot for verification of Engineer-in-Charge.

Preparation of new steel surface of any description n exc 10cm width or girth when unconneced with other painting or when painted in different tint and applying two coats of synthetic enamel paint over one coat of red oxide complete all as specified and as directed

Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, n exc 5cm long and Dialneter of neck in 5 to 10 MM complete all as specified and directed.

Deformed TMTsteel bar of grade Fe-500/500D , 5mm dia and over upto and 10 mm dia in stirrups, spacers and binders etc conforming to IS 432 cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips complete all as specified and directed.

Granite work (of any type) 18 to 20mm thick (table rubbed and polished including round edge) in steps, jambs, pillars, windowcills, cooking platforms, wash basin platform and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with granite shade over and including 15mm thick screed bed in cm 1:4 including demoliton of existing stone slab complete all as specified and directed by Engineer-in-Charge. Note : (a) The manufacturer's test certificate and individual test certificate for tiles must be submitted for approval by the concerned authority prior to installation. (b) Single piece should be used in steps/ cills/ jambs/ shelves

Factory made solid panel PVC door shutters 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, complete, all as specified and as directed.

Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.4mm complete all as specified and directed.

Flush shutters,30mm thick, solid core construction, with particle board core and ply wood face panels, commercial type on both sides, complete all as specified and directed.

Second class hard wood plain fillets square or rectangular in section exc 3 Sqcm n.exc 6 Sqcm wrought secure with screws including taking down existing one complete all as specified and directed.

150 mm long Extruded Aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

100 mm long Extruded Aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

300mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast Aluminium alloy complete all as specified and directed.

150 mm long Aluminium, anodised, barrel tower bolts of extruded section complete all as specified and directed.

18/19 mm Prelaminated particle boards exterior gde prelaminated at both sides with decorative choice lamination other side balancing white lamination including taking down existing one complete all as specified and directed.

6 mm thick teak wood lipping for 18/19 mm thick particle board fixing with nails including taking down existing one complete all as specified and directed.

Aluminium powder coated of three track sliding window outer frame top & sides (section no-20831) of size 92.0x31.75x1.5mm weighing 1.06 Kg/m, frame bottom (Section No 20832) of size 92.0x31.75x1.5mm weighing 1.248Kg/m , shutter to plain vertical (Section No 21093) of size 39x18x1.5mm weighing 0.634 Kg/m, shutter interlock vertical frame (section 21094) of size 39x18x1.55 weighing 0.734 Kg/m, shutter bottom horizontal frame (Section No 20551) size 40x20x1.5mm weighing 0.484 Kg/m, with powder coating of min thickness 50 micron , sliding type with out sash bars, 4mm thickness colour glass, rubber packing, snap beading screws with stainless steel wire mesh, including taken existing window with chowkats of any size, completet all as specified

Door closer hydraulically regulated designation No. 3, universal type, Aluminium body (extruded section), suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed including taking down existing one all as specified and directed.

Mortice lock brass 4 levers vertical type of size 100mm fixed as including taking down existing one all as specified and directed.

Mild steel, bright finished or electro galvanised continuous (piano) hinges width of flaps (when open) 30mm, including taking down existing one complete all as specified and directed.

5mm thick rubber beading strips of entrance doors having width exc 3CM to not exc 5CM to arrest entry insects including taking down existing one all as specified and directed.

Floor door stopper of aluminium body and tongue anodized with two rubber bush 150mm, in repair all as specified.

Aluminium anodized hasp and staples safety type with mild steel hinge pin incl bolt to hinge plate fixed with screws of 100mm length including taking down existing one complete all as specified and directed.

Aluminum handles cast type anodised 150 mm long including taking down existing one complete all as specified and directed.

200mm extruded aluminum alloy handles, fabricated type, anodised including taking down existing one complete all as specified and directed.

Marble mat finished tiles 10mm thick(rectangular/ Square) polished area of each tile exceeding 0.18 Sqm but not exceeding 0.42 sqm in vertical surfaces, skirting/ dado etc laid over 10mm thick back coat in CM 1:4 set and jointed in neat cement slurry and pointed in white or coloured cement to match with tiles including taking down existing floor/ skirting finishes of any description complete all as directed

Figured Sheet glass, ordinary quality and glazing, 4 mm thick with oil putty in squares not exceeding 0.5 Sq. M in each pane including Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beadscomplete all as specified and directed.

Sun control film 25 micron reflective type, in square n exc 0.5 sqm in each pane including taking down existing one complete all as specified and as directed.

Stainless steel letters of 25mm thick and height exc 10 cm and not exc 15 cm made out of stainless steel sheets of 1 mm thick including necessary fixing arrangement with granite wall cladding including taking down all as specified and as directed by Engr in charge.

False ceiling using GI snap grid size 60x60cm with main runner 38x24,wall angle & cross tee 29x24mm wall angle 24x24mm suspended with 4mm dia GI Wire fixed with steel dash fasteners carrying max load upto 8.1 Kg/Sqcm with 4mm thick designer ceiling board (Lake & Hill) all as per Everest regular T-2430 or equivalent (Make-Ramco/Charminar/Armstrong), including dismantling complete all as specified and as directed.

40 mm dia cupboard knobs fixed with nut, screw and washer of brass polished fixed including taking down existing one complete all as specified and directed.

25 mm dia mild steel powder coated drapery rod cut to length required without joint in between and fixed at openings as directed

Mild steel powder coated fancy type end brackets fixed at both ends of drapery rod same colour and type of drapery rod as directed.

Mild steel powder coated fancy type holding brackets flat 20mm wide for holding the drapary rod and fixed to wall with MS srew as specified and as directed

Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.4mm fixed including taking down existing one all as specified and as directed.

100mm long medium weight, stainless steel, butt hinges all as specified and directed.

100mm long medium weight, stainless steel, butt hinges but fixed as in repair and welded to metal fram n exc. 2.5 cm in length and n exc 6 mm of metal thickness.

75mm long medium weight, stainless steel, butt hinges all as specified and directed.

75mm long medium weight, stainless steel, butt hinges but fixed as in repair and welded to metal frame n exc. 2.5 cm in length and n exc 6 mm of metal thickness.

S&F coloured venetian blinds 100mm wide imported quality to windows vertically hanging self designed with all fittings such as brackets, rollers, pulleys etc complete all as specified. Make: Vista/ Clams/ MAC

9mm thick prelaminated particle board, interior grade, prelaminated both sides with decorative choice lamination fixed with screws to aluminium frame including taking down existing one complete all as specified and as directed.

Powder coated aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat etc. including taking down existing one complete all as specified and directed. Note: Minimum thickness of powder coating 50 micron.

Coloured tinted float glass and glazing, 5.5 mm thick with oil putty in squares not exceeding 0.5 Sq.m in each pane, with glazing clips and oil putty, including taking down existing one complete all as specified and directed.

Powder coated aluminium door shutters,aluminium section weighing 0.55kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each doors, hinges anodised aluminium snap beading screws etc including taking down existing one complete all as specified and directed. Note:-Glazing and particle board work shall be measured and paid seperately.

100 mm long Aluminium, anodised, barrel tower bolts of extruded section complete all as specified and directed.

Mild steel work angle, bars, flat iron for fencing , wall ties, hold fasts, clamps, handles, straps and similar small articles conforming to Fe-410-o or Fe-310-O complete all as specified and directed.

Cutting holes in stone wall exc half brick and n.exc one brick in cement mortar for inserting hold fasts and making good desmantled portion in cement mortar 1:3 or 1:2:4 type B-1 concrete as required.

Cutting holes in stone wall but exceeding one brick thick walls and not exceeding two brick thick wall in cement mortar for inserting hold fasts and making good desmantled portion in cement mortar 1:3 or 1:2:4 type B-1 concrete as required.

250 mm mild steel ordinary rat rail rod pattern spring including roller and roller plate including taking down existing one all as specified and directed.

Neptune Engineers and Builders

G Perumal and co

M/s Shana Constructions

kcs builders

p.chinnasamy

A.S Enterprises

m/s m valasubramanian

SRI SHIVASHAKTHI CONSTRUCTION

D.R ASSOCIATES