CANOPY FOR WZ

MH Supp & Trans,Fab — Supplying,transporting,fabricating,erecting in position in positionofPre-fabricated steel structures at all elevations for Canopyusingstructural steel sections ISMB/ISMC/ISA conforming to IS 2062 and IS 226,including cutting,welding or bolting,supply of bolts,nuts,washers etc complete as per drawings including surfacepreparation andapplying one coat of Zinc Phosphate Primerbeforeerection one coat after erection and two coats of synthetic enamelpaintas perspecification after erection and all materials and labourcomplete.(No welding is permitted at site). The rate quoted shallinclude cost of bolts,nuts,washers,welding and electrodes and any otherconsumables required for completing the work. Nut bolts shall notbeconsidered forpayment. Theoretical wight of steel sections shall beconsidered for payment.(No measurement shall be taken for nut,bolt,washer spliceplate and gusset plate)

MH Clippon Roofing — Supply and fixing Clippon Roofing System:Roofing basematerial should beof cold rolled steel of 0.55 mm thick andconform to ASTM:A446 havingyield stress of 275 MPA.Thecoating should be Aluminum and Zinc alloycomprising 55%Al,43.5 Zinc and 1.5% Silicon,as per ASTM:A792. Thecoatingmass should not be less than 150 Gms per SqM (total ofbothsides).For,bare galvalume,TCT should not be less than0.55mm. Sheetsshall have approved side laps with top sheetsfacing away from theprevailing weather. Necessary profiledfiller box should be provided athigher level of roofsheeting and at valley gutter to ensure watertightness inthe profiled gaps. The fixing of roofing shall be doneinsuch a manner that the roof is not drilled/ punctured forfixing with thepurlins.Refer to the approved makes given inthe Attachment. Flashings,Cappings and trims:These shall beformed out of same substrates as that of the roofing sheetsand shall be supplied in standardlengths of 2.5 M in therequired shapes and girths and fixed by means ofhex-headmechanically galvanized stitching screws. Siliconsealantnonhardening neutral cure type shall be applied atall laps to avoidwater seepage.

MH False ceiling — Providing and fixing false ceiling system of Trac 150 Fexterior gradeor approved equivalent of 0.5mm thickgalvanised steel with stoveenameled coil coated finishinter locking ceiling panels,carriers,suspension system andedge closure as per the following specification.Supplyingand installation of exterior grade 150 F ceilingsystemcomprising of 150mm x 17mm deep panels roll formedout of 0.5mmgalvanised steel with stove enameled coilcoated finish. The panelsshall be pre-treated and coilcoated on one side in manufacturersstandard colour shadesas approved by the Architect/Engineer in charge.The rearside of the panel shall be given a coat of primer and awashcoat while the finished side shall be given a coat ofprimer and finishcolour coat in polyster paint for admin.dry film thickness of 20microns,fixed on to the roll formedcarriers 34.5mm x 488mm deep out of6mm thick Galvanisedsteed with prongs to hold panels in the module of150 mm atmaximum 1.2 mts,C/C. The carriers to be suspended fromrooftruss by rigid suspension angles as per manufacturer'srecommendation.Panels shall be supplied in custom lengthupto maximum of 5 mts. Jobalso includes providing ceilingflashing using factory formed 0.5 mmthick Polyster coatedgalvanised steel material. Rate shall be includingprovidingflashing to cover gap if any between illuminated bandingandfalse ceiling

MH GI Facia (20 SWS) — Supplying and fixing 20 SWG GI sheet facia includingpainting with onecoat of zinc chromate primer and two coatsof 1 st quality syntheticenamel paint on front side.Necessary facia framework for fastening thesheet to thecanopy securely shall be paid separately

MH AL Gutter (2mm Thick) — Providing and fixing 2mm thick Aluminum Sheet Gutters ofrequired shapein slope with 40mm x 3mm MS. Brackets at1000mm maximum spacing and 8mmdia G.I. J or Lhooks,boltsand nuts,GI Limpet and bitumen washers,providingnut bolt joint,sealing the joints with silicon sealanttestingthe gutter for leakage by filling wateretc.Complete.(Refer attachedDrawing For allowable tolerancerefer to IS codes)

MH 6" PVC Pipe — Providing and fixing 6 inch dia PVC pipes of 6 Kg/sqcm ofapproved Makeas per IS 4985 for rain water pipes includingall fittings like bands,shoes etc. MS fabricated bracket asper requiment etc. All complete as directed by the EIC.

MH 80 W LED Light Fixture — "80 W LED Fitting as mentioned in IS standards IS 16101 to16107:Supplyand fixing of 80 W LED housed by Single piecePressure Die Cast Aluminumbody,recess mountable fittingwith guaranteed burning hours of50000. MakePhilips/Havells/Bajaj/Wipro/Osram/Crompton/GE/BeverInnov ations. IP Protection of minimum IP 65 and above,suitableforcanopy lighting at retail outlets (Petrol station).Thebidder shouldsubmit copy of certified photometric report asper IESNA LM-79(Approvedmethod for the Electrical andPhotometric Measurements of Solid-StateLighting Products)from a UL/ERTL/ERDA or any NABL accredited laboratorytovalidate the photometric claims as and when asked by HPC. Aminimum3years warranty from manufacturing defects for theluminaire bymanufacturer. i)With high lumen efficacy LEDs fromCREE,Seoul Semi 2)Conductor,LumiledPhilips,Osram,Nichia(Japan),Tridonic(Aust ria),GEandBridgelux.Efficiency of more than 90 lumens per watt.LEDsused inthe fixture should be from the same bin andcertified as per LM-80 (IESNA: Approved Method forMeasuring Lumen Maintenance of LED LightSources and LEDlumen depreciation time to L70 based on LM-80 data)byanyUL/ ERTL / ERDA or any NABL accredited laboratory tovalidate thephotometric claims and when asked by HPC. ii)Bottom open able for easymaintenance. iii)High QualityPolycarbonate Opal Diffuser for Optimumuniformity and Glarefree light output.iv)Generalelectrical protectionagainst High Voltage and Surges up to3KV v)Power factor should be greater than 0.95 vi) Range allowed for totalsystem wattage 80 W with Plus 2W or Minus 2W vii)DriverOperating Voltage Range:140 V- 270V viii)Operating Temperature 0 to +45Deg Centigrade viii)CRI more than 70 ix)Colour temperature5650K± 500K(tobe mentioned in LM 79 certificate) x)Wide beam angle for spread of light120 degrees or more xi)Luminaire PerformanceComplies to IS10322 (Part5/Sec 3)and IEC 60598-1,IEC60529,ROHS. "

MH 4C X 2.5 SQMM Copper — Supply and laying following size PVCinsulated,sheathed,armoured cableof approved makeconforming to IS 1554:Part 1:1988 4CX2.5 SQMM COPPERCABLE

MH 4CX2.5 SqMM End — END TERMINATION End termination of following cablewithdouble compression NFLP gland and crimping sockets4CX2.5SQMM END TERMINATION

MH 4" PVC Pipe — Providing and fixing 4 inch dia PVC pipes of 6 Kg/sqcm ofapproved Makeas per IS 4985 for rain water pipes includingall fittings like bands,shoes etc. MS fabricated bracket asper requiment etc. All complete asdirected by the EIC.