SPL REPAIR TO BLDG NO P-38/1 TO 12 OR MD ACCN AT SGNR MIL STN

Amount

Taking down chowkats or frame with shutter (without taking out shutter from the frame) not exceeding 1.50 sqm each as doors, windows & ventilators etc. and removal from site all as specified and directed.

Taking down chowkhats or frame exc 1.5 Sqm but n.exc 4 Sqm each with shutters (Without taking off shutters from the frames).and removal from site all as specified and directed.

Taking down shutters of any description exc 1 Sqm but not exc 2 Sqm each and removal from site complete all as specified and directed.

Taking down wooden shutters only of any description area exceeding 1.0 sqm and not exceeding 2.0 sqm each and refixing in same opening after necessary easing, adjustments, minor repairs, oiling, adjustment with cutting or fixing plain fillets/planks made from second class hard wood etc to remove gap between floor and shutter complete all as specified and as directed by Engineer-in- charge.

Supply and Fixing Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 125 x 65 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardantand fixed in position with MS hold fast / lugs/ SS dash fasteners 10 to 12 mm dia 125 mm long six numbers each frame complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be deemed included in quoted rates). ® Note : (a) For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. complete as specified by the manufacturer and as per directions of Engineer-in-charge. (b) Test certificate of Manufacturer to be provided separately. (c) Embosing with Barcode of Manufacturer engraved over each door Frame & shutter is reqd.

Supply and Fixing Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 100 x 65 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardantand fixed in position with MS hold fast/ lugs/SS dash fasteners 10 to 12 mm dia 125 mm long six numbers each frame complete as per direction of Engineer-in-Charge. Note: (a) For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. complete as specified by the manufacturer and as per directions of Engineer-in-charge. (b) Test certificate of Manufacturer to be provided separately. (c) Embosing with Barcode of Manufacturer engraved over each door Frame & shutter is reqd.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of 35mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge),minimum compressive strength 50 N/mm2, modulus ofelasticity 850 N/mm2 and resistance to spread of flameof Class A category with property of being termite/borerproof, water/moisture proof and fire retardant and fixingwith stainless steel butt hinges of required size withnecessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. Note: (a) stainless steel(304 grade) finished butt hinges 100mm -04 Nos per leaf (b) Stainless steel (304 grade ) finished square tower bolt 200mm long -02 Nos per leaf (c)stainless steel (304 grade) finished handles 200mm -02 Nos per leaf (d)stainless steel (304 grade) finished sliding door bolt 300mm -01 Nos per leaf (e)Stainless steel (304 grade ) finished floor door stopper -01 Nos per leaf

S&F second class hardwood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid decorative type glazed/guage skeleton door shutter of 35mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge),minimum compressive strength 50 N/mm2, modulus ofelasticity 850 N/mm2 and resistance to spread of flameof Class A category with property of being termite/borerproof, water/moisture proof and fire retardant and fixingwith stainless steel butt hinges of required size withnecessary full body threaded star headed counter sunk S.S screws, including S&F of stainless steel steel 304 grade (natural finish) wire cloth, all as per direction of Engineer-In-Charge. including S&F including following items: Note : (a) stainless steel(304 grade) finished butt hinges 100mm -04 Nos per leaf (b) Stainless steel (304 grade ) finished square tower bolt 200mm long -02 Nos per leaf (c)stainless steel (304 grade) finished handles 200mm -02 Nos per leaf (d)stainless steel (304 grade) finishedsliding door bolt 300mm -01 Nos per leaf (e)stainless steel (304 grade) finished floor door stopper -01 Nos per leaf(f) stainless steel (304 grade) wire cloth fixing as per manufacture.

Supply & fixing Factory made prefabricated Pressed steel Door frame made out of mild steel 1.25mm thick girth of frame 185mm including necessary MS rawl plug/bolts and fixing 75mm long butt hinges medium weight cold rolled mild steel etc and shutter including stiffeners made out of mild steel sheet 1.25mm thick cut to size, holes punched and welded seams including bending or turning up all around, mitred angle etc as required with Locking arrangement using mild steel mortise lock 4 levers with 2 Nos of keys of size 100mm (Make Godrej/Harison/Navtal) including MS chromium plated handle and 2 Nos MS locking rods out of 8 mm dia not exc 1000mm long fixed to mortise lock and handle with necessary bolts and nuts covered by MS sheet 1.25 mm thick complete including two coat of synthetic enamel paint over a shop coat of zinc chromate primer on interior surface (not -visible from front) and hammer tone paint on exterior surface (visible from front) as per Godrej Pattern complete all as specified and as directed by Engineer-in-charge.

S&F for Factory made single extruded WPC (WoodPolymer Composite) solid door/ window/Ceosetory windows & other Frames/Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60(Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives(maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with fullbody threaded star headed SS screw shaving minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N(Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof,water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners 10 to 12 mm dia 125 mm long six numbers each frame complete as per direction of Engineer-in-Charge. Note: For WPC solid door/window frames,minus 5mm tolerance in dimension i.e.depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. Note : (a) stainless steel(304 grade) finished butt hinges 100mm -04 Nos per leaf (b) Stainless steel (304 grade ) finished square tower bolt 150mm long -02 Nos per leaf (c)stainless steel (304 grade) finished handles 150mm -02 Nos per leaf

S&F in repair butt hinges of size 100 mm medium weight, stainless steel ISI marked complete all as specified.

S&F in repair aluminium handle, 150mm size (back side flat staple D type) anodized (ISI marked) complete all as specified.

S&F in repair 200 mm long aluminium anodized barrel tower bolts of extruded section (ISI marked) complete all as specified.

S&F in repair 300 mm long mild steel sliding door bolts, plate type, stove enameled black, with bright bolt not less than 12mm dia and including a minimum of 06 bolts and nuts, four on bolt plate and two on staple plate and fixed, complete, all as specified.

S&F in repair mild steel helical door spring 300mm ordinary rat tail rod pattern spring including roller and roller plate complete all as specified.

M&L for preparation of new steel surfaces of any description over 10cm width or girth and applying one coat of red oxide zinc chrome primer and two coats of synthetic enamel paint (for steel surfaces) complete all as specified.

M&L for preparation of old steel painted surfaces including as knotting, stopping, Burning off or removing, scraping etc,and then applying two coats of synthetic enamel paint (ordinary tint) on steel surfaces over 10cm width or girth complete all as specified and directed by Engineer - in - Charge.

M & L for applying two coats of synthetic enamel paint on old wood and wood based surfaces of any description, over 10cm width or girth, not other wise described including preparation of old painted surfaces.

Dismantling of boarding any description fixed in any position with nails/ screws complete all as specified.

Supply & fixing 18mm thick Plywood, grade BWR, type BB, fixed with screws to frame work along with one side laminate and other side plain white 0.9mm thick type-I, colour pattern as approved including PVC lipping, PVC sheet is heat bent as lipping on the edges of doors complete all as specified and as directed by Engineer-in-charge.

S&F 25 mm size magnetic catches with Plastic body and striking plate including letting in and fixed complete all as specified and directed.

S&F continuous (piano) hinges 20mm & 12 mm width of flap, mild steel bright finish or electro galvanised of complete all as specified fixed with CP steel screws.

Cutting holes in brick walls built in cement mortar including making good dismantled portion in CM (1:3) or cement concrete (1:2:4), type B-1, excluding half brick but n.exc one brick complete all as specified.

S & F factory made uPVC sliding window three track made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm) with or without provision of opening for cooler as directed including all fittings, steel roller system, locking arrangement etc., making arrangement for fixing of hardware, glass, wiremesh, grill etc all as per manufacture instruction and Drg No BTD-890/R & as directed. Note :- (a) The unit rate quoted by contractor excludes cost of glass & wire mesh and includes all other connected accessories. Net Opening will be measured for payment purpose. Wire mesh and Glass Shall be measured and paid Seperatly. Provision of all other items as shown on DWgs & Cutting holes of suitable depth in wall for inserting lugs etc including making good dismentalled portion with PCC (1:2:4) type B-0 using 12.5mm graded crushed stone aggreegate and cement mortar (1:3) shall be demmend to be include (b) Description of items amend accordingly as per manufacturer instructions,

S & F factory made uPVC window or ventilator side hung/top hung (glazed and gauge both) made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm) including all fittings like hinges, tower blot, peg stay, locking arrangement etc., making arrangement for fixing of hardware all as per manufacture instruction and refer Drg No BTD-890/R all as specified and directed. Note: The unit rate quoted by contractor excludes cost of glass & wire mesh and includes all other connected accessories. Net Opening will be measured for payment purpose. Wire mesh and Glass Shall be measured and paid Seperatly. Provision of all other items as shown on DWgs & Cutting holes of suitable depth in wall for inserting lugs etc including making good dismentalled portion with PCC (1:2:4), type B-0, using 12.5mm graded crushed stone aggreegate and cement mortar (1:3) shall be demmend to be include. Note :- Description of items amend accordingly as per manufacturer instructions.

S&F Stainless steel wire cloth 0.36 mm nominal dia of wire and avarage width of aparture 1.40mm and fixed etc., complete all as specified.

S&F in repairs stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples all as specified.

M & L sheet glass ordinary quality 4.80 mm thick and glazing with oil putty in square n exc 0.50 Sqm in each panes fixed to steel, metal or wooden window frames complete all as specified.

All as per Ser item No 30.00 above but pin head type, figured glass complete all as specified and directed by Engineer-in-charge.

S&F Aluminum Grill powder coated of approved design/pattern with aperture size 50 mm and wire dia 5 mm fixed with Aluminum Frame complete all as specified and directed by Engr-in-charge

S&F Framed work such as grills, gratings coolar stand, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), terrazo dado/wall tiling and skirting. etc on brick or stone walls etc including racking out joints hacking for key and scrubbing and removing rubbish off the premises complete all as specified.

M&L for 25 thick cement concrete flooring type B-0, 1:2:4, (12.5 mm graded stone aggregate) complete all as specified and directed.

Providing and Laying Premium(1st) quality straight edge, stain free, glossy finish, square marbonite double charged vitrified tiles in 600x600x7 to 8mm thick in floors etc.in approved shade , set and jointed using type-I (thick bed fixing ) confirming to IS -15477-2004 including necessary cutting as per site requirement and pointed in white coloured cement to match the shade in floors complete all as specified. jointed in neat cement slurry and pointed in epoxy grouted mixed with pigment to match the shade of tiles including 15 mm thick screed bed or bedding layer of cement mortar 1:4 for laying floor finish even & fair complete all as specified and directed by Engineer - in - Charge.

All as per Ser item No 36.00 above but on vertical surfaces/skirting dados etc over 10mm rendering in CM 1:4 finished even and fair, complete all as specified and directed by Engineer - in - Charge.

M&L Non skid ceramic cololured tiles 7 to 8 mm thick (square/rectangular) area of each tile exc 0.11 Sqm but n.exc 0.18 Sqm. in floors etc complete all as specified set and jointed in cement slurry including 15mm thick screed bed or bedding layer of cement mortar 1:4 for laying floor finish event & fair and pointed in white cement mixed with pigment to match the shade of tiles complete all as specified.

M&L for glazed ceramic coloured tiles 7 to 8mm thick 300 x 600mm size in verticle surface set and jointed in neat cement slurry and pointed in epoxy grouted pigmented to the shade also including 10mm rendering in CM 1:4 complete all as specified and directed by Engineer-in- Charge.

Dismantling stone slabs of any description or thickness in floors, apron etc laid bedded and pointed in any mortar complete all as specified and directed.

Material and labour 18mm to 20mm thickness approved shade granite of minimum size equal to width of slab (not less than 610mm) machine cut, granite duly factory grinding and polishing and chamfering the outer edges (table rubbed and mirror polished) as in cooking platform and like laid over and including 25mm thick cement mortar (1:4) screed bed including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including accomodate the hole for gas pipe complete all as specified and as directed by Engineer-in-Charge.

M&L Pre polished cut Kota stone flooring 20-25 mm thick over and including 20 mm thick screed base in cement 1:4, laid and jointed with grey cement slurry mixed with pigments to match the shade of the slabs complete all as specified and directed by Engineer - in - Charge. Note :- Single piece of Kota Stone should be provided for threads and risers is stair case.

All as per Ser item No 42.00 above but in vertical surfaces like dados or skirting over 10mm thick rendering in CM 1:4, set & jointed in neat cement slurry and pointed in white cement mixed with pigment to match the shade of tiles complete all as specified and directed by Engineer - in - Charge. Note :- Single piece of Kota Stone should be provided for threads and risers is stair case.

Demolition of Cement concrete (unreinforced) of any description and in any position not otherwise specifically provided.

Material and labour for water proofing treatment to RCC sunken slab and adjoining vertical slab as described following any one complete as per dirns of GE. Note :- Plan area only measured of toilets for payment purpose. Method 1 (a) Supplying and applying two component elastomeric acrylic polymer modified cementitious waterproofing coating, Smart Care Damp proof 2K, having 100% elongation as per ASTMD412, resisting 5 bars hydrostatic pressure as per DIN 1048, reduction to rapid chloride shall be 70 as per DIN 1048, crack bridging upto 1.2mm as per ASTM 4548.5 clean all working surface and made free from dirt, grease laitance etc. After inspection for all working area ough surface, cracks and construction joints are treated by polymer modified mortar 1:4:4 (1 Cement: 1Polymer: 4 Sand). Making Gola of size 75 x 75m at junction of vertical & horizontal with the polymer modified mortar of 1:1:4 (1 cement : 1 Polymer : Sand ). The coating shall be 2 parts of powder and 1 part of liquid without any water addition in he mixing and shall have consumption of 1.5Kg/Sqm per coats, etc, complete as per manufacturers specifications. (b) Bore packing:- All the borehole gaps between concrete surface and PVC pipe of various surface of various dia upto the neck of lvel of shall be filled with non-shrink free grout. – Smart Care GP Grout having dual shrinkage compensation property. Before the bore packing, surface of the PVC pipe and concrete surface will be made rough and sand sand will be sprinkled with polymer bonding agent. (c) Apply 12-15mm plaster on slab and vertical surface admixed with Vitalia Neo @ 200ml per bag of cement before treatment.

Method No 2 (a) Supplying and applying two component cementitious & acrylic flexible waterproofing & protective coating, two coats with 1mm DFT, having Hydrostatic (positive) water pressure resistance (DIN 1048) is 7, Abrasion resistance, cm/km is 0.09, of Dr Fixit Pidfin 2k @ 1.5Kg/Sqm with a paint brush over existing slab surface and adjoining vertical surface. The Polyester reinforced coated net of 45g/Sqm,2.5mm x 2.5mm is laying on the surface. The polyster reinforced coated net of 45g/sqm, 2.5mmx2.5mm is laying on the surface immediately on the first coat of two component modified polymer Dr Fixit pidfin 2K. After removal of all lose materials like dust etc. with wire brush coir brushe from surface to get absolutely cleaned surface of foreign contamination filling of crack and patches with polymer based mortar/micro concrete, after that making the gola on surrounding wall’s junction and seal the vertical walls. In case cutting of core cutting on the surface, the joint is seal with non-shrink grout. (b) The coating shall be terminated at 450mm height in toilets on vertical walls. (c) Apply 12-15mm water proof plaster on slab and vertical surface admixed with Dr Fixit pidiproof LW+@200ml per bag of cement before treatment. Make : Method 1 (Asian Paint)/ Method 2 (Dr fixit) or Techno Commercial equivalent make as mentioned in Appx ‘A’ (Make List) Note :- (i) The Treatment shall be carried out by authorized applicator (through specialized agency) approved by CWE as per the manufacturer. (ii) PCC filling under sunken area will be measured and paid separately.

Material and Labour for Applying Water proofing treatment on wall with first coat of chemical pidfin 2K (Dr Fixit) on cleaned surface @ 0.86 Kg/Sqm (Minimum) and drying for 24 Hours complete all as specified and as directed. (a) Applying second coat of chemical Pidfin 2K(Dr Fixit) @ 0.86 Kg/Sqm (Minimum) Over first coat. (b) The coating shall be terminated at 1600mm in toilet/2100mm in bathroom on vertical walls.

M&L for PCC 1:5:10, type E-2, using 40 mm graded stone aggregate as in filling of sunken floors complete all as specified and diredted by Engineer-in- charge.

M&L 40 mm GI pipe medium grade, made to shape as in spout pipe in sunken/ verandah/ Balcony complete all as spedifed.

Dismantling of brickwork built in cement mortar of any description complete all as specified and directed as per Engineer-In-Charge.

M&L brick work with sub class B bricks straight or curved on plan exceeding 6 mtr mean radius in cm 1:6 etc.complete all as specified and directed by Engineer - in - Charge.

M&L half brick work with sub class B bricks straight or curved on plan exceeding 6 mtr mean radius in cm 1:6 etc.complete all as specified and directed by Engineer - in - Charge.

Demolition of RCC of any description such as Roof slab , Kitchen chimney, chajja, shelves, OHT Tanks. etc and in any position not other wise specially provided for complete all as specified and directed by Engineer in Charge. Note : Reinforcement cut as required to facilitate demolition.

M&L for reinforced cement concrete type M-25(20 mm graded stone aggregate) design mix as in Slab supported on walls, beams and column in floors, roofs, landings, balconies, deck slabs and in shelves and etc. and setting in mortar complete with joints to match complete all as specified and directed by Engineer-in-charge.

M&L RCC M25 (20mm graded stone aggregate) design mix as in beams, cantileavers, bressummers, lintel over 1.50m span.

M&L RCC M25 (20mm graded stone aggregate) design mix as in chajja complete all as specified and as directed.

M&L for TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips all as specified.

M&L for TMT bars 6 to 8mm dia and over, cut to length spacers and binders required including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips all as specified.

M&L for TMT 5mm dia and over, cut to length,bent to shape as in stirrups , spacers and binders the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips all as specified.

M&L for use and waste of form work torough finished surfaces of soffits of suspended slab such as roof slabs, floor slabs, landings and similar work not exceeding 200mm thick horizontal or slopping in rough finished surface of concrete complete all as specified and directed.

M&L for formwork to sides and soffits of lintels & beams including supports, overhangs, etc. with rough finished surface of concrete complete all as specified and as directed.

M&L for formwork to chullah hood, chajjas, troughs and similar items including edges for rough finished surface of concrete complete all as specified and as directed.

M&L for formwork to edges of concrete flats,trads,break in floors,window cills,concrete railings,openings in concrete walls,floors and roofs n exc 20 cm wide and sides of RCC/Bands inwallls horizontal and sloping and similar work exc 5 cm but n.exc 10 cm wide.

Dismantling of brick tiles or terracing tiles single layer on roof & disposal of retrieved material upto a distance n.exc 100m where directed, all as specified.

Demolition of mud in roof, any thickness including plastering and leaping (where full thickness removed or only a part there of disposal off rubbish upto a distance n.exc 100m, where directed.

M&L for for 10mm thick plaster in CM (1:4) shall be provided mixed with water proofing compound, ISI marked as per manufacturer instructions. The plaster surface shall be steel toweled to get a smooth surface complete all as specified and dirceted by Engineer-In-Charge.

M&L for Roof Treatment in as specified below and as directed : (a) Over the plastered surface apply one coat of composite primer for PU coating as per manufacturers specification. Allow the primer to touch dry condition. (b) Apply 1st coat of PU coating (ShaliUrethane® LHM @ 650 gm/m2 (minimum) or equivelant) by brush / roller / spray, spread waterproofing reinforced Glass Fiber Tissue of 150 GSM with overlaps of 75mm in both directions when the surface is still tacky. Allow 1st coast to dry for 10-12 hrs. (c) Apply 2nd and 3rd coat of PU membrane (ShaliUrethane® LHM @ 650 gm/m2 (minimum) or equivelant) as per manufacturers instructions having sun reflective Index (SRI) of manimum 106 on top of roof surface after application. Treatment is to be extended on vertical and horizontal surfaces of parapet. Note : (i) The minimum thickness of roof treatment shall be 1.5mm. If any shortfall in thickness of above treatment is noticed, the thickness shall be achieved by additional coat. (ii) The plan area shall be considered for payment. (iii) The procurement of material and execution of work of water proofing treatment shall be carried out by authorised applicator approved by GE. (iv) The manufacturer / athorised applicator shall give a warranty for the performance & durability for 10 Years.

M & L for levelling course for roof slab, type B0, (1:2:4) using 12.5mm graded stone aggregate for maintaining proper roof slope and finishing surface even and smooth complete all as specified and dirceted by Engineer-In-Charge.

M&L for making benching with PCC (1:2:4), type B0, using WPC along side wall adjoining to roof in concave shape complete all as specified.

Taking up or down GI tubing 15 mm bore pipe including cleaning for re-fixing or removal to store.

Taking up or down GI tubing 20 mm bore pipe including cleaning for re-fixing or removal to store.

Supply & Fixing of 20mm outer dia CPVC pipes SDR 11 including all fittings plain/brass threaded CPVC SDR 11 fittings (like Elbow, Tee, Socket, Reducer, Union, Bushing step over bends end cap, End plugs, one side brass brass/two side brass etc) fixed along walls, ceiling or laying under floors etc and including CPVC solvent cement for jointing complete all as specified and as directed.

Supply and fixing of 25mm dia CPVC pipes SDR 11 including all fittings plain.brass threaded CPVC SDR 11 fittings (like Elbow, Tee, Socket, Reducer, Union, Bushing step over bends end cap, End plugs, one side brass brass/two side brass etc) fixed along walls, ceiling or laying under floors etc and including CPVC solvent cement for jointing complete all as specified and as directed. Note for CPVC Pipes for Ser item NO 71.00 & 72.00 :- (i) Pipes inside the buildings shall be fixed concealed and outside the buildings shall be fixed on the surface along wall with and including suitable size clamps/brackets (interval of 1m and pipe keeping 100mm away from wall) of suitable size fixed with fasterners .nut bolts as directed by engr-in-charge. Bracket with clamp, nut bolt, fatstner, slotted channel etc shall be made of deep low carbon steel material wit hot dip zinc aluminum flake coated and fixed all as shown omn BTD drawing cost for same shall deemed to be included in the quoted unit rate and nothing extra shall be admissiable on this account.

M& L for Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth In brick walls.

S&F in replacement kitchen rack/dish rack (kitchen stand or wall mounted) of size 750mm x 600mm x 250mm (appx size) and thickness of SS strip of 1mm fixed on wall including necessary arrangements and fitting accessories etc complete all as specified and directed by Engineer-in-Charge.

Taking down carefully Kitchen Rack / Dish Rack (wall mounted) and refixing after repair to building work including fixing/hanging material as required complete all as directed by Engineer-in-charge.

S&F in replacement sinks without drainage board AISI 304 quality grade 1mm thick glossy finish for kitchen or laboratory with plugs, washers and CP waste couplings of 32mm dia including cast iron brackets connecting union etc, overall size 915mm x 460mm/928mm x 458 mm with bowl size 410mm x 355mm x 185mm/ 430 x 355 x 200 including connection pipe and wall plinth and making good disturbed portion in CM 1:3 or PCC 1:2:4, complete all specified and directed by Engr-in-charge.

S&F sinks without drainage board AISI 304 quality grade 1mm thick glossy finish for kitchen or laboratory with plugs, washers and CP waste couplings of 32mm dia including cast iron brackets connecting union etc, overall size 915mm x 460mm/928mm x 458 mm with bowl size 410mm x 355mm x 185mm/ 430 x 355 x 200 including connection pipe and wall plinth and making good disturbed portion in cm 1:3 or PCC 1:2:4 complete all specified and directed by Engr-in-charge

S&F in repairs 15mm bore Long body bib tap, cast copper alloy, chromium plated with capstan head, screwed down, screwed for iron pipe or for brass ferrule, complete all as specified & directed.

Supply and Fixing in repair Angular Stop Cock with fange, fency type chromium plated copper alloy screwed down, high pressure, screwed one ends for 15mm bore of iron for union and fixed in position complete all as specified and as directed by Engineer-in-Charge. Make : Jaquar( Cat No VGP-81053 (Vintage Prime) or equivalent from Cera (Valentina Single Lever Series) or Techno commercial equivalent make as mentioned in Appendix ‘A’

S & F PVC connection 15 mm size with PTMT nuts of length 600 mm of approved quality complete all as specified.

S&F in repairs brass chromium plated shower rose 125 mm of size with arm and with or without swivel joints to steel pipe or union complete all as specified and as directed.

Supply and fixing 15mm bore single lever high concealed diverter flow consisting of exposed part kit with operating lever, wall flange and button and concealed body, cartdge sleeve and also including bath spout with flange chromium plated, screwed down, high pressure complete all as specified and as directed by Engineer-in-Charge. Make : Cera(exposed part F1018721, concealed part F4030101, bath spout F1020661), Jaquar or Tecno commercial equivalent in make mentioned in Appendix ‘A’

Supply and fixing in repair 15mm before single lever basin mixer with popup waste system and 450mm long braided hoses, fency type, cast copper alloy, with capstan heads, chromium plated, screwed down, high pressure , specified and as directed by Engineer-in-Charge. Make : Jaquar (Cat No VGP-8105B (Vintage Prime) or Cera (Cat No FR-1013451) or equivalent from Hindware(Fluid Series) or Techno Valentina Single Lever Series) or Techno commercial equivalent make as mentioned in Appendix ‘A’

Supply and fixingin repair single lever sink mixer with swinging spout with connecting legs & wall flangs, wall mounted, fency type chromium type plated cast alloy screwed down, high pressure, srewed ends for 15mm bore or iron pipe or for union and fixed in position complete all as specified and directed by Engineer-in-Charge. Make : Jaquar (Cat No VGP-81165 (Vintage Prime) or Techno commercial equivalent in make mentioned in Appendix ‘A’

S&F in repair fancy type SS curtain rod 25 mm dia with brackets knob rings (20 cm c/c) etc including all necessary fittings complete all as specified and directed by Engineer - in - Charge.

S&F in repairs brass chromium plated tubular towel rail, 20 mm dia, D type, 60 cm long between flanges.

S&F in repair Stainless Steel grating 125mm dia with waste hole (Minimium weight 40 grams)

S&F in repair Stainless Steel grating 100mm dia without hole (Minimium weight 25 grams)

S&F in repair chromium plated soap tray any type and fixed to plugs on wall with chromium plated brass screws complete all as specified and directed.

S&F in replacement corner vitrous China wash basin, white, flat back of size 450mm x 390mm, including brackets, waste coupling & PVC waste pipe of 32 mm dia etc and cutting for and pinning in end of brackets or erecting with long screwed shanks & fly nuts, flange end bedded in red lead cement including necessary fittings complete all as specified and directed by Engineer-in-charge.

S&F in repairs Vitreous china premium/1st quality wall hung water closet with P trap white, ivory, off white including connection to drain (or out going pipe) and to flushing pipe, anti syphonage pipe etc. and including plastic soft close seat cover as recommended by manufacturer for particular model close pattern with flat bottom etc including suppluy and fix of all necessary accessories set like rag bolts, gel gasket/ hinges etc as recommended by manufacturer for fixing, packing and taking down existing of any description/ size complete in all respect all as specified and as directed.

S&F health faucet (Hand Shower) fancy type, CP including 1.2 meter long 8mm dia wasy flex tube in chrome finish and including wall hook and fixing material making connections and fixed in position complete all as specified and as directred by Engineer-in-Charge. Make : Jaquar (Continental series) ALD-573/Hindware (contessa plus series)/ Cera (Ocean series) or Tecno commercial equivalent in make mentioned in Appendix ‘A’

S&F sheet glass shelf assembly of 300x300mm for corners consisting of 5.5 to 6 mm thick glass shelf and with beveled edges / hatchings of edges fixed with stainless steel ‘D’ bracket fixed and railing complete all as specified and as directred by Engineer-in-Charge.

Dismantling water tanks of any description exc 250 and n.exc 500 ltrs capacityand removal from site all as specified and directed.

S&F 500 Litre capacity Rotational moulded polyethylene water storage tanks Triple layered White coloured (cylindrical, vertical with closed top) ISI marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. complete, all as specified and directed.

S&F 20 mm ball valves high pressure of PTMT with epoxy coated aluminium rod & highdensity plastec ball screwed for iron pipe and fixed including necessary fittings. (Minimum weight 20mm - 210 gms) etc complete all as specified and directed.

S&F 25mm gun metal globe or gate valve with iron wheel head, screwed both ends for CPVC 25mm dia pipe and fixed also including necessary fittings complete all as specified and directed.

Taking down rain water pipe and eaves gutters (any size and pattern) including all fittings heads shoes bends swan necks etc including cleaning or refixing or removal to store. Note : Measured overall as fixed along the centre line over fittings and accessories.

Dismantling and disconnecting existing CI soil waste/vent pipe 100 mm bore fixed to wall,laid in trenches incl all fittings & accessories

Dismantling and disconnecting of existing CI soil waste/vent pipe 75 mm bore fixed to wall,laid in trenches incl all fittings & accessories

S & F 110 mm bore of pipe PVC (SWR) pipes single socket in any length with rubber ring joint fixed to walls with MS clamps complete all necessary fittings as specified and directed.

S & F 75 mm bore of pipe PVC (SWR) pipes single socket in any length with rubber ring joint fixed to walls with MS clamps complete all necessary fittings as specified and directed.

S & F 110 mm bore of pipe PVC (SWR) bends of any radius / shoe fixed to PVC pipes as directed.

M&L PVC (SWR) junction 110 mm branch piece equal or unqual complete all as specified and directed by Engineer-in-Charge.

M&L PVC (SWR) junction 110 mm double (Single T), equal or unqual complete all as specified and directed by Engineer-in-Charge.

S & F 75 mm bore of pipe PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed by Engineer-in-Charge.

S & F 75 mm bore of pipe PVC (SWR) bends of any radius / shoe fixed to PVC pipes as directed.

M&L PVC (SWR) branch pieces, 75 mm bore, (equal or unqual), complete all as specified and directed by Engineer-in-Charge.

M&L PVC (SWR) 75 mm P Trap complete all as specified and directed by Engineer-in-Charge.

M & L for Salt glazed stoneware gully traps of size 150 x 150 mm, square or round mouthed, type 'P' complet all as specified.

Taking down Cement plaster including raking out joints hacking for key scrubbing down with water etc

M&L 15mm thick, rendering in cement mortar 1:6 to brick/concrete wall surfaces finished even and smooth without using extra cement complete all as specified and directed by Engr-in-Charge.

M&L 15mm thick, rendering in cement mortar CM 1:4 to brick/concrete wall surfaces in two layers first layer 10mm thick and second layer 5mm thick with and including WPC 3% by weight of cement finished even & smooth without using extra cement complete all as specified and directed by Engr-in-Charge.

M&L 5mm thick, rendering in cement mortar 1:3 to ceiling surfaces on patches finished even and smooth without using extra cement in patches complete all as specified and directed by Engr-in-Charge.

Material and labour for complete removal of existing treatment of any type/description from external/internal wall/ceiling surfaces, soffits/chajja/roof projection surfaces etc by Mechanical sander/grinder machine having suction vaccum bag (smart periodical methodology), complete all as specified and as directed by Eningeer-in-Charge.

M&L for applying two coats of acrylic emulsion on newly plastered surface of ceiling etc complete all as specified.

M&L for applying two coats of acrylic emulsion on old plasterd ceiling surfaces etc complete all as specified.

M&L for preparation and applying two coats of interior emusion paint (light shade) @ 12 sqm/ltr/2 coats by using gun to wall surfaces over and including a coat of interior wall primer @ 10 sqm/tr/1 coat as recommended for under coat by manufacturer of interior emulsion and brands complete all as specified and directed.

M&L for preparation and applying two coats of exterior emusion paint (light shade) @ 12 sqm/ltr/2 coats by using gun to wall surfaces over and including a coat of external wall/RCC surfaces/soffits of chajjas/roof projections/ cantilevers/ balcony etc surfaces over and including a coat of exterior wall primer @ 11 sqm/ltr/1 coat as recommended for under coat by manufacturer of exterior emulsion and brands complete all as specified and directed

M&L for new plastered surfaces and prepares surface after complete removal, applying acrylic wall putty in internal/external wall/RCC surface/soffits of chajjaas/roof projection/cantilevers/balcony/ceiling etc (thickness vary from 1.5 to 2.5 mm as required for desired smoothness and leveling of surfaces in two or more layers) by using ready made wall care putty including sand papering after filling the putty to make surface smooth and ready for receiving interior/extrior painting complete all as specified and directed. Note : (i) The prepared surface after wall putty, the contractor will inform to the GE as well as to the Engineer-in-Charge for site inspection before applying further external fisnished. Please note that the further external fisnished work will start only after approval of the prepared surface from the GE as well as to the Engineer-in-Charge through site order

M&L for Obliterating old writing of any description, n exc 0.1 sq. m, with paint to match existing work etc complete all as specified and directed by Engineer - in - Charge.

M&L for Writing letters or figures with fluorecent paint ( Block. Roman, Italic or Indian) n exc. 30 cm high etc complete all as specified and directed by Engineer - in - Charge.

M&L for welding in repairss Thickness of metal to be welded will be Exc 9 mm but not exc 20mm complete all as specified and directed by Engineer - in - Charge.

M&L for Mild steel work as ISMB, joists channel,angle or tee section fixed adjacent to ceiling and embedding in floor and brickwork including cutting welding and the like including caps.bases,splices etc,built from one or more beam or channel section or angle with plates including all lattice bars, stiffeners,gusset plates including necessary welding,rivetting etc.confirming to Fe 410 (Gde E-250) quality A etc all as specified and directed by Engineer-in-charge.

M&L for shotcreting average thickness 25mm in RCC columns, beams and slab etc. (with mix minimum cement content of 350 Kg per Cum, M-25). Concrete having the specified minimum characteristic compressive strength (with ordinary portland cement, coarse sand and graded stone aggregates of 6mm to 10mm size in proportion as per design criteria) incl the cost of centering and shuttering at edges and corner etc as directed by Engr-in-Charge incl chipping of unsound/week concrete material 25mm average thickness from slabs, beams/columns etc with mannual Chisel or standard power driven percussion type all of approved makes incl tapering of all edges, making square shoulder of cavities including cleaning the exposed concrete surface and reinforcement with wire brushes and throughly washing with water and allowing it to dry etc incl removel of rust by applying approved rust remover chemical and the coating with Dr Fixit Epoxy zinc primer @ 6 Sqm per Litre at DFT of 100 micron as per manufacturer's instruction and specification, including 5mm thick cement plaster in CM 1:3 finished even and smooth without using extra cement including removing rubbish material from building and thrown in low lying empty area at any distance from the site as directed complete as specified and as directed by Engineer-in-Charge. Note : Complete treatment to be executed by approved applicator.

Supply and fixing hard drawn steel wire fabric not exc 4kg/sqm cut to lengths, wire mesh to be fixed and firmly anchored to the concrete surface by means of 'L' shaped mild steel shear key welded with existing reinforcement including cost of material, labour, tools and plants incl welding/L-clip/tying with mild steel wire (annealed) not less than 0.9mm dia complete all as specified and as directed.

Drilling Holes of 12mm dia up to 100 mm deep holes in structural members at the interval of 300 mm in staggered manner or along the crack line in Reinforced Concrete (RC) structural element including cleaning of the holes by air blower and inserting 12mm dia NRV (Non Returnable Valve) nozzle compatible with epoxy injector and having machined external end to receive outlet of Grouting Gun. Fix inside the hole by applying thixotropic epoxy adhesive to ensure complete sealing and allow curing the system for minimum of 8 Hrs before Grouting including nozzle projections, excess putty, if any, over concrete element by grinding, leveling and finishing the external surface, after completion of the work, etc. complete all as specified and as directed by Engineer-in-charge.

Grouting, injecting two parts, low viscosity, moisture insensitive injection liquid, based on high strength epoxy resin by pressure and using pressure epoxy injector with accessories till nozzle refused to accept the grout including mixing of grout having following properties:- (i) Mixed Density 1.1 kg/l (at +27°C); Viscosity ~ 250 mPas at +30°C and should comply according to ASTM C 881, Type II and IV, Grade-1, Class E+F (ii) Compressive strength >= 70 N/sqmm (7 days) according to ASTM C 579; Tensile Strength ~ 50 N/sqmm (after 7 days at +30°C cure) (According to ASTM D 638); Tensile Modulus ~ 2000 N/sqmm (after 7 days at +30°C cure) (According to ASTM D 638); (iii) Bond Strength ~ 10.8 N/sqmm (failure in concrete) after 14 days at +30°C cure; Flexural strength ~ 50 N/sqmm according to ISO 178. (iv) Seal the nozzle with thixotropic epoxy adhesive after the refusal of grout material from the nozzle. Note:- leakage through other nozzle or cracks are required to be monitored while grouting and such points to be sealed as and when required without any extra cost complete all as specified and as directed by Engineer-in-charge. Note :- Mode of measurement: per kg of material consumed

Taking down carefully aluminium point wiring (light, fan, socket or power, bell complete fitting such as sockets, ceiling roses, pendants, batten holders, regulators and making good the disturbed surfaces of wall, floors, ceiling in CM 1:3 etc complete all as specified and directed by Engineer - in - Charge.

M & L for concealed conduit point wiring complete for light/ fan on independent /combine board with cable 1.5 sqmm (Nominal area) FRLSH PVC insulated multistranded unsheathed copper conductor, drawn in and including PVC Concealed conduit pipe medium grade 20 mm dia, pipe hooks , elbows, juction covers and junction boxes , after cutting in wall chasing for conduits and sinking's for metal flush boxes suitable length and thickness for mounting, switches, sockets,fan regulator with cover plate with frame and making the good disturbed surfaces of wall in CM 1:3 with white wash or existing colour including provision of continuous earth continuity conductor along with point wiring of 1.5 sqmm copper PVC insulated cable for one light/ fan point controlled by one switch and connected to common earth dolly, complete all as specified and direced by the Engineer in charge.

All as per Ser item No 131.00 above but for one switch socket combination 5/6 amp on independent board complete all as specified and directed by Engineer - in - Charge.

All as per Ser item No 131.00 above but for one three pin socket outlet 5 Amp on same board with other switches complete all as specified and directed by Engineer - in - Charge.

All as per Ser item No 131.00 above but for one switch socket combinationt 6 pin 5/ 15 Amps on independent board with copper conductor 2.5 Sqmm complete all as specified and directed by Engineer - in - Charge.

All as per Ser item No 131.00 above but for one light point controlled by two 2 ways switches complete all as specified and directed by Engineer - in - Charge.

All as per Ser item No 131.00 above but for call bell point complete all as specified and directed by Engineer - in - Charge.

S & F in replacement switch piano flush type 5/6 Amps single pole one way complete all as specified and directed by Engineer - in - Charge.

S & F in replacement switch socket combination 5 pin, type 5/6 Amps flush type complete all as specified and directed by Engineer - in - Charge.

S & F in replacement switch socket combination 6 Pin, 5/16 Amps flush type complete all as specified and directed by Engineer - in - Charge.

S & F in replacement switch 2 way 6A complete all as specified and directed by Engineer - in - Charge.

S & F in replacement Socket outlet 5 pin 5 Amps flush type complete all as specified and directed by Engineer - in - Charge.

S&F in replacement bell push 6 A complete all as specified and directed by Engineer – in - Charge.

S & F in replacement stepped type, fan regulator not less than 120 watt for ceiling fan 1200/1400mm sweep complete all as specified and directed by Engineer - in - Charge.

S&F in replacement buzzer AC 230 Volt single pole ding dong type complete all as specified and directed by Engineer - in - Charge.

S & F in replacement ceiling rose surface bakelite three terminals complete all as specified and directed by Engineer - in - Charge.

S & F in replacement of existing light fitting with LED batten 20W LED batten with 'Eye Soft' technology & glarefree diffuser for perfect application in modern homes or aliminium housing and integrated electronic driver, 20 watt having input voltage AC 140-300V, 50 Hz , 6500K, and all other accessories including connection with flexible cable copper conductor twin core of size 23/.2 mm upto ceiling rose/connector complete all as specified and directed by Engineer - in - Charge.

S&F security light fitting LED TYPE 25 watt with all necessary acessories, Clear transparent acrylic cover, prewire suitable to operate on 230 volt 50 HZ AC & Supply and fixing to wall / on pole including fixing arrangement with suitable galvanized iron pipe 35 mm bore “light grade” brackets 2 mtr length bent to shape to obtained required shape including clamps, nuts / bots / washers etc connecting with suitable flexible copper wire of size 23/0.0076 complete all as specified and directed by Engineer - in - Charge.

S & F in replacement Water tight bulk head fitting (New pattern),comprision of connector, weather proof enamelled gallery, including 10 watt LED llight with separate driver all as specified and directed by Engineer - in - Charge.

S & F angle holder insulated body with back plate for conduit fittings complete all as specified and directed by Engineer - in - Charge.

S&F LED lamp 9W for angle holder complete all as specified and directed by Engineer - in - Charge.

S & F in replacement of sub-main wiring with two single core cables PVC insulated and un-sheathed 6 sqmm (Nominal Area) FRLSH stranded copper conductor drawn in and including steel dia 25mm “medium quality” conduit including 6.00 Sqmm (Nominal Area) copper cable as earth continuity conductor after chasing in wall and making good the disturbed surfaces and white wash or existing colour, necessary junction box and covers including necessary connections, PVC flexible pipes are used in pannel board while connecting the cable complete all as specified and directed by Engineer - in - Charge. Note :Two run cable, one run of wire and one run of PVC conduit will be measured as one unit.

S&F in repairs Sheet metal enclosure for single door Vertical DBs made out of CRCA mild steel sheet surface with insulated material like polyester with epoxy powder coated surface mouting SP & N 8 Way 240 Volt ISI marked 200 Amps busbar stove enameled dust and vermin proof suitable for incorporation MCBs and Isolators etc complete all as specified and directedby engineer -in-charge.

S & F in replacement MCB ‘C’ series type suitable for 240 volts, AC supply 32 Amps, S P & N with over load and short circuit protection and rupturing capacity not less than 10KA complete all as specified and directed by Engineer - in - Charge.

S & F in replacement MCB ‘B’ series type suitable for 240 volts, 10 KA, AC supply 6 to 32 Amps , single pole (SP) with over load and short circuit protection and rupturing capacity not less than 10KA complete all as specified and directed by Engineer - in - Charge.

S&F in repairs Sheet metal enclosure for double door Vertical DBs made out of CRCA mild steel sheet surface with insulated material like polyester with epoxy powder coated surface mouting VTPN 4 Way 415 Volt ISI marked 250Amps busbar stove enameled dust and vermin proof,IP:43 protection suitable for incorporation FP MCCB(V-Tech) N3 Frame upto 125A, Isolators and including give connection with wire and cable etc complete all as specified and directedby engineer -in-charge.

S&F in repairs MCCB 4 pole, 63 Amps with breaking capcity 16kA ,Fixed TM and 415 volts AC Supply ISI marked complete all as specified and directed by Engineer - in - Charge.

M & L for Earthing complete with GI earth plate electrode 60 cm x 60 cm x 6 mm thick burried directly in ground (earth pit not less than 2.25 Mtr deep below ground level ) with top edge of plate not less than 1.5 Mtr below ground level , connecting to GI earth lead 4 mm dia GI earth wire ,by means of bolts,nuts and washers of GI and protection by provision of GI medium grade pipe 15 mm bore including provision of concrete pit in PCC (1:2:4) type B1 using 20 mm grade stone aggregate with 40 mm thick cover of RCC (1:2:4) reinforced with XPM (weight not less than 4 gs /Sqmm ) and frame of angle iron 25mmX25mmX6mm with lugs 02 Nos and with 6 mm dia MS bar handle made to shape ,GI light grade 20mm bore pipe for watering perforated at the bottom 1.75 meter long placed ontop edge of earth plate common salt and charcoal filling test point made out of 40 mmX 8 mm FI with fixing arrangement ,funnel, wire mesh and earth work inhard dense soil, returning filling in and removal of surplus soil to a distance not exceeding 50 mtrs all as per electric plate no.3 of SSR part 1 and connecting to earth test point all as specified and directed by Engr -In - Charge

S&F heavy duty metal body exhaust fan of 300 mm sweep, 240 volt, copper winding, complete with louvers and shutter and mounted in suitable opening arrangement in wall and connecting up including 3 core PVC insulated PVC sheathed copper conductor flexible cable 24/0.2mm from ceiling rose to fan complete including breaking of brick wall and making a hole for fixing of exhaust fan including grouting of bolts and making good to distubed wall in cement mortar (1 :4) white washing matching with existing colour etc.

S&F exhaust fan made of sturdy engineering plastic of 250mm sweep,, 240 volt complete with louvers and shutter and mounted in suitable opening arrangement in wall and connecting up including 3 core PVC insulated PVC sheathed copper conductor flexible cable 24/0.2mm from ceiling rose to fan complete including breaking of brick wall and making a hole for fixing of exhaust fan including grouting of bolts and making good to disturbed wall in cement mortar (1:4) white washing matching with existing colour etc

Taking down fan, sealing cable end, dismantling blades and removing fan and blades to store complete all as specified and directed.

M&L for painting of ceiling fans complete, in situ with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust etc complete all as specified and directed.

Hanging only ceiling fan (M.D. supply) and connecting up including provision of cable from ceiling rose or connector to fan all as specified and directed by Engr-in-Charge.

S&F rigid non metallic PVC conduit 20mm dia inclusive of all tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc complete all as specified and directed.

S&F TV socket having holes for 20mm conduit entry for TV connection complete all as specified and directed.

Excavation in trenches not exceeding 1.5 mtr wide and not exceeding 1.5 mtr depth for laying of cables including taking up or down the LT cable complete all as directed

Returning, filling in, including spreading, leveling, watering and well ramming in soft/loose soil in layer not exceeding 25 cm thick complete all as specified and directed by Engineer - in - Charge.

Removal of excavated material to a distance n. exc 50m and deposited where directed at level n. exc 1.5m above the starting point complete all as specified and directed.

M & L for sand cushioning with dry coarse sand to under ground cable 23 cm thick, 8 cm thick below the cable and 15 cm thick after laying the cable complete all as specified and directed by Engineer-in-Charge. Note : Thickness after punning shall be considered for payment.

Supply and lay standard size bricks sub class 'B' type complete all as specified and directed.

Supply and lay jointing and testing and commissioning in replacement of 25 Sqmmx4 core XLPE insulated, screened , PVC bedded galvanised steel strip or wire armoured electric power cable heavy duty multi stranded aluminium conductor & PVC sheathed LT cable 1100 V grade conforming to IS-7098 laid in trenches/ducts/fixed on poles wall/laid under roads/paths/drain/culverts or passing through pipes complete all as specified and directed by engineer in charge.

Supply and lay GI pipe 50mm light grade for cable protection in walls trenches or any situation including clamp nut bolt etc complete all as specified and directed.

S& F in repairs concealed cistern set with full frame compatible with wall hung type water closet complete all as specified and directed by Engr-in-Charge. Make : Cat No B1110101, B1130101, B1190104, B1190105, B1190106, B1190107 of Cera/Hindware/Parryware/Hindustan Sanitary ware.

M&L for PCC (1:3:6) type C-2 (using 40mm graded agg) 75mm thick as in plinth protection complete all as specified and directed by Engr-in-Charge.

Supply only integral water proofing compound, ISI marked complete all as specified and directed by Engr-in-Charge.

J and P CONTRACTOR (BID ID -3368795)

AYUSH BUILDERS (BID ID -3368888)