Provn of DG set of capacity 62.5 KVA, Special repair to LT Network and Addn/Altn to LT Panel, cable alongwith other connected works in certain different locations under GE (Utilities) Udhampur .

Supply, installation, testing and commissioning (factory made and tested CPRI type test certified) LT feeder pillar box (KIOSK) out door type, floor mounted,compartmantalised suitable for 415 Volts 3 phase 4 wire, 50 Hz AC supply system, dust and vermin proof, made of 3.15mm CRCA MS sheet with digital Volt meter, Ammeter, with CTs ,Led lamps RYB for all incomers & outgoings base frame of 50x50x6mm angle iron , powder coated, having front and rear openeable hinged double door shutters with aprons for cable entry and locking arrangement including taking down old U/S LT panel/busbar complete all as specified and directed by Engr-in-Charge with following accessories :- Incoming :- (a) MCCB 160 amps, 4 pole, 50Hz ,415 V with rupturing capacity 35/36 KA-01 No. (b) Bus bar electrolytic grade copper and supported on Non-hygroscopic, non carbonising, corrosion resistance SMC insulators 300 Amp,4 pole, not less than 75 cm long mounted on insulators-01 set.

Outgoing :- (a) MCCB 63 amps, 4 pole ,Ics=100%Icu- 25/26 KA, 415 Volts, with thermal magnetic adjustable and fixed magnetic setting with extended terminals-2 Nos. Note- (i) Rate quoted is deemed to be inclusive of PCC foundation/pedestal and connected earth work. (ii) Panels shall be placed above 0.6 mtr from ground level. (iii) Outgoing MCCBs shall be fed with solid busbar connectors. (iv) Cables shall be terminated using gun metal /SS glands. (v) Including suitable thimbles/lugs, nut bolts ,washers fitted the cables. (vi) Cable glands for incoming and out going suitable cables is including rate quated by vendover.

All as per serial item No-1.00 here-in-before but of following accessories:- Incoming:- (a) MCCB 4 pole ,Ics=100%Icu- 25/26 KA, 415 Volts, 100 Amps , with thermal magnetic adjustable and fixed magnetic setting with extended terminals-01 No. (b) Bus bar electrolytic grade copper and supported on Non-hygroscopic, non carbonising, corrosion resistance SMC insulators 200Amp,4 pole, not less than 75 cm long mounted on insulators-01 set. Outgoing:- (a) MCCB 4 pole ,Ics=100%Icu- 25/26 KA, 415 Volts, 100 Amps , with thermal magnetic adjustable and fixed magnetic setting with extended terminals-01 No. (b) MCCB 4 pole , Ics=100%Icu-25/26 KA, 415 Volts, 63 Amps , with thermal magnetic adjustable and fixed magnetic setting with extended terminals-02 Nos.

All as per serial item No -1.00 here-in-before but of following accessories:- Incoming:- (a) On load change over switches 4 pole of capacity 100 Amps-01 No. Outgoing:- (a) Bus bar electrolytic grade copper and supported on Non-hygroscopic, non carbonising, corrosion resistance SMC insulators 200 Amp,4 pole, not less than 75 cm long mounted on insulators-01 set.

Supply , installation, testing and commissioning of outdoor type,weather proof, cubicle panel board made out of 3.15 mm thick MS/CRCA steel mounted on 60cm long legs made out of 40x40x6mm equal angle, embedded in PCC 1:2:4 type B-1 bocks of size 15x15x20 cm, front and back openable, double door openable upto minium 150 deg & removal type having chromium plated locks, louvers and air vent gaskets for natural air flow suitable for 3 phase 4 wire 415 volts 50 Hz ,factory febricated with suitable foamed-in PU gasket to make it dust/vermin proof , IP 54 protection, Powder coated and prewired as per standard engineering practice, the panel manufacturer should have got any one of the panel tested at CPRI earliest for short circuit current of 50 KA for one second and similar design and technology shall be adopted for fabrication of panel copy of CPRI test report shall be produce to GE along with a certificate from manufacturer of the panel that the similar design and standard have followed in these panels.complete ,suitable cable glands for cable entry. The panel shall be suitable to accomodate the following equiptments :- (a) Alluminium Bus bar of capacity duly covered with colour coded shrinkable sleeves not less than 100 amps for Phases and 50 Amps for neutral - 02 set. (b) MCB TPN 63 Amps, - 02 Nos. (c) MCB SP 10 A - 10 Nos. (d) Panel indicating lamp neon/LED type (Red, Yellow & Blue) with lamp holders - 03 Nos.

(a) Alluminium Bus bar of capacity duly covered with colour coded shrinkable sleeves not less than 100 amps for Phases and 50 Amps for neutral - 02 set. (b) MCB TPN 63 Amps, - 02 Nos. (c) MCB SP 10 A - 10 Nos. (d) Panel indicating lamp neon/LED type (Red, Yellow & Blue) with lamp holders - 03 Nos.

Supply, installation, testing and commissioning of 62.5 KVA, AMF Panel, indoor type, factory made, (C.P.R.I. Approved) suitable of 440Volts, 3 Phase, 4 Wire, 50 HZ, AC Supply, dust, weather and vermin proof, made out of 2 mm thick sheet, openable front and back side, base angle frame 40X40X5mm, Aluminium bus bar 200 amp. Mounted on SMC/DMC insulators and enclosed on all sides, (Bus bar cross section area 1 sq. mm = 1 amp.) for panel shall be powder coated with Siemens grey shade, internal wiring with PVC insulated, strand copper conductor cable on adequate size but not less than 2.5 sq. mm and approved manufacturer of L.T. Panel including following accessories. Make: SMS Panels and Switchgear or equvalant and components as following. (a) AMF relay microprocessor base(Make-Procon)-01 No (b) Contactors MNX-140 amp,3 pole,220 volt Make -L&T -02 No (c ) Control material -01 Lot.

Steel tubular swaged poles erected to truly vertical or planted as strut complete with 6 mm thick mild steel base plate, welded to Pole, B-118 finial taper cap, bolts, nuts and screws, poles made out of ERW MS tubing conforming to IS-2713 Part-II type 410-SP-31 (9m long) including drilling of holes of required size for fixing of cross arms, painting the exposed surfaces of pole with two coats of aluminum paint over a coat of red oxide zinc chrome primer and with two coats of black bituminous paint on the end portion embedded in concrete, making five black and white bands at lower portion of pole above ground level/coping each 300 mm wide alternately and marking pole number with black paint at suitable height complete all as specified and directed by Engineer-in-Charge. Note:- The earthwork, PCC foundation, steel clamps, MS Cross arms & bracing of angle iron etc will be measured and paid separately under relevant items of Sch ‘A’(BOQ).

Steel tubular swaged poles erected to truly vertical or planted as strut complete with 6 mm thick mild steel base plate, welded to Pole, B-118 finial taper cap, bolts, nuts and screws, poles made out of ERW MS tubing conforming to IS-2713 Part-II type 410-SP-64 (12 m long) including drilling of holes of required size for fixing of cross arms, painting the exposed surfaces of pole with two coats of aluminum paint over a coat of red oxide zinc chrome primer and with two coats of black bituminous paint on the end portion embedded in concrete, making five black and white bands at lower portion of pole above ground level/coping each 300 mm wide alternately and marking pole number with black paint at suitable height including The earthwork, PCC foundation,deemed to be coated rate by contractor complete all as specified and directed by Engineer-in-Charge.

LED flood light with lens 120 watt made uppressure diecast aluminium housing with toughned glass and high power LEDs and secondary lens with IP 66 protection system of efficasy >110/125 LPW including 10 KV SPD including taking down old UNSV Street lights complete all as specified and directed by Engr-in-Charge. Make:- CG/Philips/Wipro.