Provn of certain Minor and Revenue works (M-02 and R-05 Nos) under GE Gurdaspur.

Amount

M&L for MS framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings and hanging including fastening Fe-290 (Grde-E165) and fixing complete all as directed.

M&L for applying two coats of synthetic enamel paint over and incl one coat of red oxide primer with and incl preparation of new surface of steel not exc 10 cm in width or girth, complete all as specified and directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft/loose soil all as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm.

Removing excavated material not exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point.

M&L for PCC 1:3:6 type C-2 (using 40mm graded crushed stone aggregate) as in foundations fillings & mass concrete complete all as specified and directed.

M&L for hardcore (broken stone) of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc 15 cm thick, watered and rammed to a true surface complete all as specified and directed

M&L for RCC M-25 design mix as in column footings, plinth beams complete all as specified and directed.

M&L for RCC M-25 design mix as in column ( except footings) complete all as specified and directed.

M&L for RCC M-25 design mix as in chajja, lintels, shelves and fascia complete all as specified and directed.

M&L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape as required, including cranking, bending spirally hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips all as directed.

M&L for mild steel TMT bars 5mm dia and over upto and including 10mm dia as in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips all as directed.

M&L for form work to sides of fair finished flat surfaces of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work vertical or to batter complete all as specified and directed.

M&L for form work to fair finished square, rectangular or polygonal form work to sides of pillars, posts, struts, columns and stanchions complete all as specified and directed.

M&L for form work to fair finished flat form work to sides and soffits of floor or roof beams, lintels, cantilevers, shelves includidng supports etc complete all as specified and directed.

M&L for 40mm thick damp proof course in cement concrete 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregate) in horizontal or vertical surfaces including necessary formwork complete all as specified and directed.

M&L for brick work with fly ash bricks, straight or curved on plan exc 6m mean radius built in CM 1:6 complete all as spcified and directed by Engineer-in-Charge.

M&L for rendering 12mm thick with ready mix mortar of approved make on brick work/ stone/ concrete wall, facia, projection etc external finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

M&L for rendering 15mm thick with ready mix mortar of approved make on brick work/ stone/ concrete wall, facia, projection etc external finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

M&L for preparing of newly plastered surface and applying two coats of Oil bound distemper over a coat of primer on wall complete all as specified and directed.

M&L for preparing newly plastered surface and applying two coats of cement base paint over a coat of primer including preparation of surface on wall complete all as specified and directed.

Forming embankments including raising (or lowering) earth, spreading in layers n. exc 30cm thick watering, ramming/ rolling and finishing to required size, shape etc n. exc 1.5m high from base, earth to be used from item No 05 all as specified.

M&L for 100 mm thick, PCC 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) as in sub base for flooring complete all as specified and directed.

M&L for vitrified designer, heavy duty tile of size 400mm x 400mm, 12mm thick, coloured, set, jointed and pointed in neat cement slurry with white cement and pigment as in path/ floor, pattern of tile as approved by GE over 15mm thick in cement mortar 1:6 for laying floor finishing including demolition existing tiles with screed complete all as specified and directed.

M&L for 20mm thick black granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over and including 15mm thick CM 1:6 complete all as specified and directed.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick , ISI Marked of colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

S&F rolled mild steel Gde Fe-410-W Gde E-250 quality-A in roof trusses (framed), trussed, purlins crane gantries, joist, channel, steel tube, rails & fastenings & heavy brackets framimg (beam, tee, angle, coulmn, gusset plates, channel, hollow square/rectangular or flat section) including distance pieces, cleats with riveted, bolted or welded attachment etc. complete all as specified and directed by Engr-In-Charge.

M&L for preparation of new steel surface exc 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L for 75mm thick PCC 1:3:6 type C-1 (using 20mm graded crushed stone aggregate) as in plinth protection finishing the surface even and fair including cutting grooves 10mm x 30mm deep at every 3.0m interval and filled with mastic filling comprising 1 part of mastic bitumen and 3 parts of sand (all by weight) complete all as specified and directed by Engineer-in-Charge.

Earth work in excavation by mechanical means (Hydraulic excavator) means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out in any type of soil and disposal of excavated earth lead upto 50 m and lift upto 1.5m, complete all as specified and directed by Engineer-in-charge.

All as per item No 30 above but exc1.50m to 3.0 m deep soft/loose soil complete all as specified and directed

M&L for cement concete in foundations, filling and mass concrete 1:4:8, type D-2 (using 40mm graded crushed stone aggregate) complete all as specified and as directed

M&L for RCC (design mix M-30) in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete, complete all as specified and directed.

M&L for RCC (design mix M-30) in Walls, retaining walls, basement walls, ballast walls and the like; any thickness; above top of footings; including attached pilasters and buttresses, complete all as specified and directed

M&L for RCC (design Mix M-25) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the likeSlabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified

Use and waste for formwork to faces of walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttresses, etc vertical or to batter all as specified and directed.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick complete all as specified and directed

Framed work as in manhole cover slab angle or other section with gusset plates or gates of angle or other section with gusset plates, rails, braces, etc complete, drilled for fixing of steel sheeting or other covering doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified and as directed .

M&L for precast RCC 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) as coverslab for manhole and similar work etc complete all as specified and directed.

S&F 100mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixerd to wall/floors upto 12m ht all as specified & directed.

S&F PVC (SWR) 100mm bore bends any radius complete all as specified and directed.

S&F 100mm bore PVC (SWR) perforated pipes single socketed in any length with rubber ring joints fixerd to wall/floors upto 12m ht all as specified & directed.

S&F 150mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixerd to wall/floors upto 12m ht, complete all as specified & directed.

S&F 150mm bore PVC (SWR) perforated pipes single socketed in any length with rubber ring joints fixerd to wall/floors upto 12m ht all as specified & directed.

S&F grating round 150mm size of PTMT (Minimum weight 100gms) Grating all as specified & directed.

M&L for boring with drill/reverse rotary rig circulation method including electric logging through any kind of strata of soil /rocks for drilling not less than 200 mm dia hole for depth not exceeding 75 meter deep below ground level by keeping sufficient space for packing pea gravel including disposal of surplus soil/ liquid mud/ sand etc complete all as specified and directed. Note :- (i) One No trial bore will be carried out for Borewell. If possibility of water seen then before should resume. (ii) In case of failure of borewell additional borewell wll be carried out by contractor, expenses deemed to be included in quoted rate. (iiii) Trial broe and necessary fuel, lubricant, and chemical extra required for construction work shall be arrange by contracter and cost of these items shall be deemed to be included in quoted rates.

M&L for loose filling with 40 to 60 mm broken stone aggregate all as specified and as directed by Engr-in-charge.

M&L for loose filling with 3 to 10 mm broken stone aggregate all as specified and as directed by Engr-in-charge.

M&L for loose filling with coarse sand all as specified and as directed by Engr-in-charge.

M & L for PCC (1:5:10) type E-2 (using 40mm graded crushed stone aggregate) as in foundation, filling and mass concrete complete all as specified and directed.

M&L for PCC 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) as in kerbs or mud stops , coping, rounded or chamfered on edges complete all as specified and directed.

Excavation in post holes in soft/loose soil (or simila holes) each n. exc 0.5 cum getting out, returning, filling in and ramming earth or broken rubble mix with earth around in layers not exceeding 25 cm complete all as specified and directed.

S&F for galvanized, 2 strand steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacing straining bolts, including securing and tying at crossing with and provision of galvanized mild steel wire, staples or steel pins etc. complete all as specified and directed. Note:- Each line of wire to be maesured separately.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts etc including provision of binding wire complete all as specified and directed.

Supply only 3 or 4mm dia PVC Coated galvanised mild steel chain link fencing of mesh size 75mm x 75mm fixed with string bolts complete all as specified and directed.

M&L for mild steel work of angles, flat iron as in post and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, embeding in concrete/foundation etc. conforming to Fe-290 Gde E-165 complete all as specified and directed by Engr-in-charge.

M&L for mild steel bolt factory made with hexagonal or square heads at one end and screwed the other, to be fitted with washer etc and one hexagonal or square nut, exc. 5cm and not exc. 10cm long and dia neck 10 to 12mm complete all specified and directed.

S&F mild steel round bars conforming to Fe-290 Gde E-165, 10mm dia and over as in chain link fencing, fixed to concrete post with mild steel nuts, bolts and washers and tying GI chain link fencing including hooking of ends for fixing between flat iron and nuts & bolts and welding wherever reqd ends complete all as specified and directed

S&F PVC (SWR) 150mm bore bends any radius complete all as specified and directed.

s.v and co (BID ID -3468698)