PROVN OF IRON FENCING AROUND BLDG NO P42 UNDER GE NARANGI

Amount

M&L surface excavation not exceeding 30 cm deep and averaging 15cm deep and getting out in soft/loose soil complete all as specified and directed.

Excavation in trenches n.exc 1.5m wide and not exceeding 1.5 m in depth for foundation etc, or for shafts, wells, cess pits, manholes, pier holes, etc. not exceeding 10 Sqm on plan and not exceeding 1.5 m in depth and getting out in soft / loose soil etc complete all as specified and as directed.

Returning, filling in including spreading, levelling, watering and well ramming in layers not exceeding 25 cm each in soft / loose soil etc complete all as specified and as directed.

Removing of surplus excavated material not exc 50m and depositing where directed at a level n. exc 1.5 m above the starting point etc complete all as specified and as directed.

M&L for hardcore of broken stone or boulders of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface etc complete all as specified and as directed.

M&L PCC (1:3:6) type C-2 (using 40 mm graded stone aggregate) in foundation filliing and mass concrete complete all as specified and as directed.

M&L PCC (1:4:8) type D-2 (using 40 mm graded stone aggregate) in foundation filliing and mass concrete complete all as specified and as directed.

M&L PCC (1:3:6) type C-2 (using 40 mm graded stone aggregate) in surface channel and drain complete all as specified and as directed.

M&L for RCC 1:2:4 type B1(20mm graded stone aggregate) nominal mix as in Foundations, including rafts, footings, foundation beams, plinth beams, bases for columns, etc, basement slabs, under-reamed piles and mass concrete etc complete all as directed.

M&L for RCC 1:2:4 type B1(20mm graded stone aggregate) nominal mix as in Columns, pillars, piers, posts and struts etc.complete all as specified as directed.

Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified as directed.

Formwork to sides of pillars, posts, struts, piers, columns, and stanchions complete all as specified as directed.

M&L for brick work with old size sub class 'B' bricks straight or curved on plan exc. 6m mean radius and built in CM 1:6 etc complete all as specified as directed.

M&L for brickwork with subclass ‘B’ old sized bricks, straight or curved on plan to any radius in half brick thick walls and built in CM 1:4 etc complete all as specified as directed.

M&L TMT steel bars 10mm dia and over, cut to length, bent to shape required, incl cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips

M&L TMT steel bars 8mm dia , cut to length, bent to shape required, incl cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips

M&L for mild steel TMT bars 5 mm dia and over upto and including 10mm dia cut to length, bent to shape required including cutting, cranking, hooking ends and binding with mild steel wire (annealed) not less than 0.90mm dia as in stirrups, spacers and binders complete all as specified and as directed.

S&F mild steel angle iron post & strut etc. in fencing including embedding in concrete and screwing etc. including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work confoRming to Fe-290 GdeE-165 completed all as specified and as directed.

S & F Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, not exceeding 5 cm long and diameter of shank 5 to 10mm completed all as specified and as directed.

S&F rolled mild steel sections as in main and cross beams, hip and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors fixed with angle cleats or other connecting plates confirming to Fe-410-W ( Gde-E-250) quality B complete all as specified & as directed.

S&F rolled mild steel framed works as in doors or gates of angle or other section with gusset plates,, rails, braces etc complete drilled for fixing of steel sheeting or other covering doors etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings ( exclusive of steel sheeting or other covering, running rails and guides) and hangings also fastening and fixing etcconforming to Fe.290.Gde-E-165.

Supply only chain link fencing wire mesh of 100X100mm size or type, made with 4 mm dia mild steel galvanised wire complete all as specified and as directed.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolt etc including provision of binding wire complete all as specified and as directed

S & F galvanized two strand, steel barbed wire 2.24 mm dia barbed with 2 mm dia bars at 75 mm spacing and straining and fixing to RCC / steel post etc., including securing or tying at crossing with and providing of galvanized mild steel wire, staples or steel pins, etc., (each line of wire to be measured separately) complete all as specified and as directed.

M&L for 75mm thick PCC 1:4:8 type D-2 (using 40mm graded stone aggregate) as in sub-base complete all as directed.

M & L pre-polished cement concrete chequered tiles area of each tiles exc 0.06 Sqm but n exc 0.11 Sqm and 25 mm thick with white cement and pigments of approved make jointed with cement slurry and pointed with white cement mixed with pigment to match with the tiles over and including screed bed of 20 mm thick in cement mortar (1:6) complete all as specified and directed.

M&L for 20mm thick granite ( any type) machine cut ,as in steps, jambs, pillars, window cills, cookong platforms and the like laid over cement screed of 15mm thick in CM 1:4 including pointing in white cement 1:2 using marble dust with admixtures of pigments match the shade of granite stone including rubbing and polishing complete all as specified and as directed.

M&L for 15 mm thick rendering in CM 1:4 on brick/ concrete surfaces and finishing the surfaces even and smooth without using extra cement complete all as specified and as directed.

M&L for preparation of newly plastered surface of wall and applying three coats of white wash on wall surface complete all as specified and directed.

M&L for preparation of new steel or iron surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paints over a coat of red oxide, zinc chrome primer complete all as specified and as directed.

S&F LED Post Top light 70 Watt made of cast aluminium with decorative opal polycarbonate diffuser with IP 65 protection including GI pipe of suitable dia for mountingcomplete all as specified and as directed.

Supply, laying and testing of XLPE insulated, PVC sheathed, armoured, heavy duty electric under ground cable, with stranded aluminium conductor, 1100 Volts grade of size 6 sqmm 2 core laid in trenches / floor or fixed on wall /pole with brass compression cable glands, terminal lugs etc, complete all as specified and as directed.

Supply and lay GI tubing 40mm bore light grade for cable protection and fixing to the existing pole with flat iron clamp 25x 3mm including nut bolts complete all as specified and as directed.

Supply and spreading fine dry river sand for cushing to UG cable including spreading levelling and hand punning etc complete all as specified and directed.

M&L for sub class 'B' old size bricks laid in trenches for cable protection laid flat width wise along the length of cable complete all as specified and directed.

M& L for Manual boring under roads / hard standing by required T&P without disturbing the top surface of the road for passing the cable in GI Pipe of 40 mm to 100mm dia complete all as specified and as directed.

S&F street light junction box of size 155mmX210mmX92mm made of high quality polycarbonate with IP 66 protection ( Dust and vermin proof as per IEC 60529) totally insulated made of halogen and silica free recyclable material having high quality gasket made out of polyurethene with MCB, DP, 10 KA, 6 Amps to be fixed on Din rail, with locking arrangement with cable gland suitable upto 10 sqmm cable and necessary fixing arrangements such as clamps, nuts, bolts etc complete.Make ; HENSEL CAT NO. DK-1610G.

M/S SAMIR PAUL