Construction of Balance works of Girls Hostel Boys hostel 3-seater and Director bungalow at the permanent campus of National Institute of Technology Meghalaya at Sohra Cherrapunjee Meghalaya

Amount

Total Amount of BoQ 2

Amount after unconditional Rebate

Description of Work / Item(s)

Amount

Total of BoQ 3, BoQ 4, BoQ 5 and BoQ 6

Total Amount of BoQ3 (Item Rate)

Total Amount of BoQ4 (Percentage Rate)

Total Amount of BoQ5 (Percentage Rate)

Total Amount of BoQ6 (Percentage Rate)

Description of Work / Item(s)

Amount

Schedule - (D) Bill of Quantites for Non Schedule Items (MR ITEMS) (Civil and Electrical)

EARTH WORKS

NS 1-Diluting and injecting chemical emulsion for pre constructional anti-termite treatment and creating a chemical barrier under and around wall trenches, basement excavation, top surface of plinth filling, junction of walls and floors along with external perimeter of the building, surrounding the pipes and conduits etc. complete at the rate of 7.5 liters (or as directed by the manufacturer) per sqm on vertical surface and 5.0 liters (or as directed by the manufacturer) per sqm on horizontal surfaces, 50% of the emulsion to be filled in the holes made in trenches at 150mm center to center etc.complete as per IS:6313/1981 (Part-II), manufacturer's specifications and direction of the Engineer -in-charge.( plinth area of the building at ground floor only shall be measured in sqm for payment )With chloropyriphos emulsifiable concentrates of 20 % with 1 % concentration.

NS 1 a- Earth work in excavation by mechanical means (Hydraulic excavator, concrete breaker/hilti, tractor mounted compressor) / manual means over areas (exceeding 30 cm in depth, 1.5m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50 m and lift upto 1.5 m, disposed earth to be levelled and neatly dressed.

Ordinary rock

NS -1b - Excavation work by mechanical means (Hydraulic excavator)/ manual means in foundation trenches or drains not exceeding 1 .5m in width or 10 sqm on plan including getting out the excavated soil and disposal of surplus excavated soils as directed, dressing of sides and ramming of bottoms, lift upto 1.5 m, including within a lead of 50m.

Ordinary rock

NS 1c - Excavating trenches of required width for pipes, cables, etc, including excavation for sockets, depth upto 1.5 m including getting out the excavated materials, returning the soil as required in layers not exceeding 20 cm in depth, including consolidating each deposited layers by ramming, watering etc., stacking serviceable material for measurements and disposal of unserviceable material as directed, within a lead of 50m :

Ordinary rock

Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia.

NS 1d - Extra for excavating trenches for pipes, cables, etc. in ordinary/hard rock exceeding 1.5 m in depth but not exceeding 3 m. (Rate is over corresponding basic item for depth upto 1.5 metre.)

CONCRETE WORK

NS 2 - Providing and laying light weight foam concrete in sunken portion at all levels. Density of the concete shall be 400-450 Kg/Cum using OPC as binder, litho foam as network former, litho foam SL 200L as forming agent and fiber, all complete as per manufacturer's specification and direction of Engineer-in-charge

FIRE DOOR

NS 3 -Providing and fixing of fully insulated 55 mm thick wooden fire / smoke check door shutter using 31mm thick FR insulation with internal facia of 9mm thick calcium silicate board having density not less then 950 Kg/cum on both sides and faced with 4mm thick commercial ply facing including 15X55 mm size hardwood beading with fire and smoke seal of size 10 X4 mm fitted along vertical and horizontal edges of the shutter .The complete door system should be capable to achieve Two hour fire rating in accordance with BS:476 Part 20and IS:3614 part II.Rate to include 150x75mm Hardwood door frame duly embedded with Promseal Intumscent Smoke Strip as per manufacturer's specification all complete . The door shutter shall also have a vision panel 6mm thk, 200mm x 300mm / 300mm x 300mm fire rated glass ( to be paid saperately), surrounded with fire proof treated teakwood beading, all around complete in all respects as per manufactures specifications and direction of the Engineer-In-Charge.

NS 4- Providing & Fixing following fire rated fittings as per manufactures specifications and direction of the Engineer-In-Charge.

NS 4A - Door Locks

NS 4B- Glass Wired Vision Panel of size 200mmx300mm

NS 4C - Door Closer

NS 4D - SS door Handles 150 mm

NS 4E - SS tower Bolts 300 mm

FLOORING WORK

NS 5-Providing & laying Granite stone flooring with 18mm thick stone (sample of shall be approved by Engineer-in-charge) over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with grey cement slurry including rubbing and polishing complete with :

NS 6- Providing & fixing Granite work gang saw cut (polished and machine cut) of thickness 18mm for wall lining,skirting and dado (veneer work) in cement mortar 1:3 (1 cement : 3 coarse sand) including pointing with white cement mortar 1:2 (1 white cement : 2 marble dust) with an admixture of pigment to match the marble shade: (To be secured to the backing by means of cramps, which shall be paid for separately).

NS 7- Providing Flamming on granite stone slabs in floors, landing and treads complete including required material for the purpose as per direction of Engineer-in-charge.

FINISHING WORK

NS 8- Providing & Fixing Chicken Mesh of apreacher 25mm with 22 SWG Wire on the junction of R.C.C work & brick work under the plaster by U nail. Complete as per direction of Engineer in charge.

NS 9-Providing & fixing SS wire gauge of average width of aperture 1.4 mm with wire of dia 0.63 mm for aluminium doors/window fixed with nessecary screw / washer complete in all respects as per direction of Engineer-In- Charge.

SANITARY INSTALLATIONS

NS 10- Providing and fixing C.P. brass twin coat hooks fixed on toilet door with C.P. brass screws

NS 11- Providing and fixing 15 mm dia C.P. Ablution health faucet with 1.0 m long SS extension pipe with wall hook and operating knob complete in all respects.

NS 12- Supplying, fitting and fixing C.P on brass Two way Bib cock of approved model including cutting and making good the walls wherever required complete in all respect as per Enginerr in charge.

NS 13 -Providing & fixing solid state, no touch operting, fully hygienic hand drier of approved shade with blower, continuous repeat usage, time delay, summer & winter control, music while drying, volume ON/OFF controls including providing necessary bracket cable from drier to plug, plug top key and lock etc. complete as required.

NS 14 -Providing & fixing C.P. brass basin Mixer Tap with aerator complete as required.

NS 15 - Providing & fixing C.P. brass sink Mixer Tap with aerator complete as required.

NS 16 -Providing & fixing in position of white vitreous china below counter wash basin / circular / oval (510x395 min.)with C.I. brackets painted white, 32 mm dia C.P. brass waste, 32 mm dia C.P. cast brass bottle trap, including cutting and making good the walls and floors where required.

INTERNAL DRAINAGE (SOIL, WASTE & FITTINGS)

NS 17 - Providing and fixing, uPVC pipes 6 Kg/Cm2 (IS: 4985 ) including all fittings (plain or door) e.g. bends, junction, offsets, access pieces, jointing with rubber ring/solvent cement joints including required suports,cutting chase or holes in walls and floors and making good where required.(for soil & waste pipes, ASP pipe) as per direction of engineer incharge.

NS 17A- 110 mm OD.

NS 17B- 160 mm OD.

NS 17C- 200 mm OD.

NS 18 - Providing & fixing in position uPVC P"or S" trap of self cleaning design of following sizes for the embedded areas. Making proper connection with drip-seal joints, cutting chase / hole in floors /slabs and bringing the same in proper condition in cement concrete 1:2:4 mix complete as required. including cost of cutting and making good the walls and floors where required.

110 mm inlet and 110 mm outlet

NS 19- Providing and fixing pvc pipes conforming to relevent I:S including all fittings, testing, cutting holes or chases and making good where required. (For waste connections).

NS 19A- 32mm dia (10 kg/cm2)

NS 19B- 50mm dia (6 kg/cm2)

NS 20 - Providing and fixing multi-floor trap fitting with maximum 3 inlets 32,40 or 50 mm size fabricated from 100/150 mm dia upvc pipes and sockets,fixed to p trap with solvent joint and set in cement concrete as per standard drawing complete.

NS 21 - Providing and fixing END CAP or cleanout plug( Ceiling or Floor) with suitable inset keys for opening, male threaded joint with socket fixed to uPVC/SCI pipe complete in all respects.

110 mm nominal pipe size

NS 22 -Providing and fixing on wall face unplasticised PVC (working pressure for 4 Kg/cm2) rain water pipes comforming to IS: 4985 including jointing with seal ring conforming to IS : 5382 leaving 10mm gap for thermal expansion. ( For-Soil/Waste/Rwp pipes). 160 mm dia(OD).

INTERNAL WATER SUPPLY

NS 23 -Providing & fixing butterfly valve tested to a pressure of 15 Kg/Sq.cm. Including rubber gasket, flanges, nuts, bolts, washers & painting complete as required.

NS 23A -65 mm dia

NS 23 B-80 mm dia

NS 23C -100 mm dia

NS 24 - Providing and fixing G.I. pipe headers in various length conforming to IS:1239 heavy class including all flanged connections as per drawing / site requirement. Supports from wall, floor and ceiling etc. Including dead end flanged connection. MEDIUM CLASS.

NS 24A -65 mm dia

NS 24 B-80 mm dia

NS 24C -100 mm dia

NS 25 -Providing and Fixing full way lever operated forged brass ball valve of brass body with forged brass hard chromeplated steel ball tasted to a pressure not less than 15 kg/sqcm with threaded / flanged joints complete with nuts, bolts, gaskets, washers etc.

NS 25A -65 mm dia

NS 25 B-80 mm dia

NS 25C -100 mm dia

(ELECTRICAL WORKS)

NS 26 - Design, manufacturing, assembling, wiring, supply, installation, testing and commissioning of the following extensible cubicle type indoor mounting, dead front, fully compartmentalised with hinged lockable detachable front & back openable, dust and vermin proof, floor mounting sheet steel clad switchboard fabricated of 2 mm thick CRCA powder coated sheet steel frame work and covers, 3mm thick for gland, plates i/c cleaning & finishing complete with aluminium alloy bus bars of high conductivity, DMC/ SMC bus bars of high conductivity, DMC/ SMC bus bar supports, with short circuit withstand capacity of 31 MVA for 1 Sec., bottom base channel of MS section not less than 100mmx50mmx5mm thick, fabrication shall be done in transportable sections, entire panel shall have a common copper earth bar of size 25mmx5mm at the rear with 2 Nos. earth stud, solid connections from main bus bar to switch gears with required size of Al. bus bars and control wiring suitable for use at 415 volts 3 phase 4 wire 50 cycle system, BMS Compiatable and to withstand a symmetrical fault level of below mentioned kA at 415 volts. Panels shall be fabricated in easily transportable sections, length, height, depth etc. to match with site condition, complete in all respect.

Residence Block

NS 26.1- ENERGYMETER

Supply, Installation, Testing & Commissioning of 10-60A, 1-phase, KWh Energy Meter direct base mounting in Existing Cubicle with CTs complete as approved.

HOSTELS

NS 26.2 MDB-06/1 (Typical for MDB-06/3 and MDB-08/1, MDB-08/3)

INCOMER

1 No. 250 A FP MCCB (35 KA) with thermal magnetic release for short circuit and over current complete.

METERING & INDICATION

1 Sets of `ON' , `OFF', `Trip' and R,Y,B phase indicating lamps

BUS-BAR

1 Sets of 300A TPN Aluminium Bus Bar with colour coded PVC Sleeves

OUTGOINGS

1 Nos. 100A FP Isolator of 10 kA breaking capacity.

6 Nos. 40/63A FP MCB (10 KA)

NS 26.3 SDB-06/1 (Typical for SDB-06/3 and SDB-8/1, SDB-08/3)

INCOMER

1 No. 100 A FP ATS (Auto Transfer Switch)

1 No. 100 A FP MCCB (35 KA) with thermal magnetic release for short circuit and over current complete.

METERING & INDICATION

1 Sets of `ON' , `OFF', `Trip' and R,Y,B phase indicating lamps

BUS-BAR

1 Sets of 150A TPN Aluminium Bus Bar with colour coded PVC Sleeves

OUTGOINGS

4 Nos. 40/63A FP MCB (10 KA)

2 Nos. 32A FP MCB (10 KA)

NS 26.4 MDB-06/2 (Typ. For MDB-08/2)

INCOMER

1 No. 400A FP MCCB (35 KA) with Microprocessor release for E/f, short circuit and over current complete.

METERING & INDICATION

1 Sets of `ON' , `OFF', `Trip' and R,Y,B phase indicating lamps

BUS-BAR

1 Sets of 500A TPN Aluminium Bus Bar with colour coded PVC Sleeves

OUTGOINGS

1 Nos. 125A FP Isolator of 10 kA breaking capacity.

11 Nos. 40/63A FP MCB (10 KA)

NS 26.5- SDB-06/2 (Typ. For SDB-08/2)

INCOMER

1 No. 125 A FP ATS (Auto Transfer Switch)

1 No. 125A FP MCCB (35 KA) with thermal magnetic release for short circuit and over current complete.

METERING & INDICATION

1 Sets of `ON' , `OFF', `Trip' and R,Y,B phase indicating lamps

BUS-BAR

1 Sets of 150A TPN Aluminium Bus Bar with colour coded PVC Sleeves

OUTGOINGS

5 Nos. 40/63A FP MCB (10 KA)

6 Nos. 32A FP MCB (10 KA)

NS 26.6 - MDB-07/1 (Typ. For MDB-07/2)

INCOMER

1 No. 200A FP MCCB (35 KA) with thermal magnetic release for short circuit and over current complete.

METERING & INDICATION

1 Sets of `ON' , `OFF', `Trip' and R,Y,B phase indicating lamps

BUS-BAR

1 Sets of 300A TPN Aluminium Bus Bar with colour coded PVC Sleeves

OUTGOINGS

1 Nos. 125A FP Isolator of 10 kA breaking capacity.

8 Nos. 40/63A FP MCB (10 KA)

NS 26.7 - SDB-07/1 (Typ. For SDB-07/2)

INCOMER

1 No. 125 A FP ATS (Auto Transfer Switch)

1 No. 125A FP MCCB (35 KA) with thermal magnetic release for short circuit and over current complete.

METERING & INDICATION

1 Sets of `ON' , `OFF', `Trip' and R,Y,B phase indicating lamps

BUS-BAR

1 Sets of 150A TPN Aluminium Bus Bar with colour coded PVC Sleeves

OUTGOINGS

6 Nos. 40/63A FP MCB (10 KA)

LT CABLE (Supply)

NS 27 - Supply, Receiving & storing of the following sizes of 1.1 KV grade XLPE insulated Aluminium conductor armoured, stranded, Power Cables in the existing Cable Trays /Pipes /laid underground /surface etc., as required, as per technical specifications /details.

NS 27.1 - 3.5C x 25 sq. mm Aluminium Armoured cable

NS 28 - Supplying and fixing of following rating, 240/415 volts, "c" curve, Miniature Circuit Breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commisioning as required.

NS 28.1 - S/F DP MCB (63 AMPS)

NS 28.2 - S/F DP MCB (40 AMPS)

LIGHT FIXTURES

NS-29 - Supplying of the following LED light fitiing including fixtures complete etc. as required.

NS 29.1 - Surface/ wall mounted 1x20 watt LED light fitting, polycarbonate housing, constant current output driver, i/p voltage 100-300V AC, PF>0.90, THD<20%, IP 20, efficacy minimum 100 lm/W, 2000 lm, Color temperature 6500K, CRI>80, Surge protection>2.5 Kv, Life >25000 hrs, temperature range -10°C to 45 °C etc as required.

NS 29.2 - Wall mounted 1x9 watt LED wall bracket light fitting, polycarbonate housing, constant current output driver, PF>0.90, THD<20%, IP 20, CRI>22, Surge protection>2.5 kV etc as required.

NS 29.3 - Surface/ wall mounted mirror light 1x10 watt LED light fitting, polycarbonate housing, constant current output driver, i/p voltage 100-300V AC, PF>0.90, THD<20%, IP 20, efficacy minimum 100 lm/W, 1000 lm,Color temperature 6500K, CRI>80, Surge protection>2.5 kV, Life >25000 hrs, temperature range -10°C to 45 °C etc as required.

NS 29.4 - Surface mounted 1x6 watt LED RD light fitting, polycarbonate housing, constant current output driver, i/p voltage 180-270V AC, PF>0.90, THD<20%, IP 20, efficacy minimum 100 lm/W, 600 lm, Color temperature 6500K, CRI>80, Surge protection>2.5 kV, temperature range 0°C to 45 °C etc as required.

NS 29.5 - Surface mounted 1x18 watt LED SQ fitting, polycarbonate housing, constant current output driver, i/p voltage 180-270V AC, PF>0.90, THD<20%, IP 20, efficacy minimum 100 lm/W, 1800 lm, Color temperature 6500K, CRI>80, Surge protection>2.5 kV, temperature range 0°C to 45 °C etc as required.

NS 29.6 - Surface mounted 1x10 watt Bulk head LED light fitting, polycarbonate housing, constant current output driver, i/p voltage 180-270V AC, PF>0.90, THD<20%, IP 65, efficacy minimum 100 lm/W, 1000 lm, Color temperature 5500K, CRI>80, Surge protection>2.5 kV, temperature range 0°C to 45 °C, Electrical class-I, Life>50000 hrs etc as required.

NS 29.7 - Surface mounted 1x12 watt LED RD light fitting, polycarbonate housing, constant current output driver, i/p voltage 180-270V AC, PF>0.90, THD<20%, IP 20, efficacy minimum 100 lm/W, 1200 lm, Color temperature 6500K, CRI>80, Surge protection>2.5 kV, temperature range 0°C to 45 °C etc as required.

NS 29.8 - Wall/Ceiling mounted 2x18 watt LED light fitting, polycarbonate housing, constant current output driver, i/p voltage 100-300V AC, PF>0.90, THD<20%, IP 20, efficacy minimum 100 lm/W, 3600 lm, Color temperature 6500K, CRI>80, Surge protection>2.5 kV, temperature range -10°C to 45 °C etc as required.

NS 29.9 - Surface mounted 1x30 watt LED light fitting, CRCA powder coated white housing, constant current output driver, operating voltage 140-170V AC, PF>0.95, THD<10%, IP 20, IK03, efficacy minimum 110 lm/W, 3300 lm, Color temperature 5700K, CRI>80, Surge protection>2.5 kV, temperature range -10°C to 45 °C etc as required.

NS 29.10 - Supply & Fixing of cylindrial pole in galvanizes steel with UV resistant PVC coating fully weatherproof 3.0 meter high, minimum dia. 60mm made of 4mm thick steel plate having base plate with reinforced thermoplastic body, Nipple / Reducer to Install Post Top Lantern fitting, window and flush cover with locking arrangement at suitable height from base for cable termination block, pole suitably reinforced with welded steel section at window cut section to make the strength of pole unaffected, with 10/16A SP MCB and 3 way TPN connector, including providing of 3x1.5 sq.mm. Cu. wire from JB to Light fittings as required,including template and anchor plate 240x240x3mm with 4 nos 450mm long, 16mm dia foundation bolts etc as required.

NS 29.11 - Post Top Lantern LED light fitting, 1X20 watt LED Landscape lighting, constant current output driver with high voltage open & short circuit protection, i/p voltage 140-270V AC, PF>0.95, THD<10%, IP 65,IK06 efficacy minimum 100 lm/W, 3600 lm, Color temperature 5500K, CRI>70, Surge protection>2.5 kV, temperature range -10°C to 50 °C etc as required.

NS -30 - Supplying, storing, and assembling of the Wall Bracket Fan, white in color, 400mm including connection, testing, commissioning etc. as required. Jerk free oscillation and smooth running, Thermal overload protector (TOP) helps in protecting the motor in case of any high voltage fluctuation. Speed 1350 RPM, Air delivery 72 CMM, 50 watt, Aerodynamically designed balanced heavy duty PP blades, pull chain swing function etc as required.

NS 31 - SITC of ISI marked heavy duty, 300mm Exhaust Fan (Grey), Metallic blade finish; Air delivery:195 m³/h, Includes: Fan, Motor, Arm-set, Frame, Blade, Mounting accessories kit and Guarantee card, Warranty: minimum 2 years on product, double ball bearings, speed of 900 RPM etc. as required.

NS 32- Manual Call Box

Providing, fixing, testing and commissioning of Manual Break glass type call box made of 16 SWG CRCA Sheet and having chrome plated hammer and chain etc. complete as specified.

NS 33 - Hooter

Electronic alarm sounders on the surface of wall or false ceiling connections etc. complete as specified.

NS 34 - Providing, fixing testing and commissioning of Local Control panel of following number of zones, strictly as per IS-2189, with battery & power supply as required. The operating supply to the local control panel system shall be fed from main control panel. Each and every zone shall have visual indications like – isolation, fire, open circuit in detector circuit short circuit in detector circuit, fire alarm acknowledged, additionally each and every zone shall have the following switches- isolation fire test, open circuit test, short circuit test, fire alarm acknowledge, fault alarm acknowledge, lamp test, panel system switch etc. as required. The panel shall be wall mounted, and enclosure shall be made of 16 SWG CRCA sheet steel and having front door lock and key etc. complete as specified

NS 34.1 - 4 Zones

NS 35- Supplying, fixing, terminating tel. wire, testing & commissioning of following pair, Telephone Tag Block complete in all respect.

NS 35.1 - 10 Pair

NS 35.2 - 50 Pair

NS 36 - Supply & Installation of CAT 6 information outlets complying fully or exceeding with category 6 connecting hardware specifications for all pair combinations up to 250 MHz. Outlets shall use lead frame technology, non PCB pyramid type. (Blue in Colour for Data) complete as required.

NS 37 - Upto 5 way TV Spiltter / Tap-Off box in 16 SWG G.I. box of suitable size with lockable door. Ref. Cat. No. Legrand - OnQ VM0104 Vertical Coax Splitter, 1X6, 1GHz or equivalent.

NS 38 - Supplying, storing, Installation, Testing & commissioning of the following capacity Storage type Hot Water electrical horizontal heaters with insulation, and stove enameled M.S. bracket, thermostatically controlled immersion heater, with pilot lamp, 15/20mm dia inlet with non return valve and 15/20mm dia outlet including making connections complete in all respects as required. (ISI Marked)

NS 38.1-15 Ltrs

NS 38.2 - 25 Ltrs

NS 38.3 - 35 Ltrs

NS 38.4 - 50 Ltrs

NS 39 - SAFETY EQUIPMENTS

NS 39.1 - Supplying and fixing of non-skid rubber mat 12mm thick and 900mm width as required including cutting to required lengths of approved make with Test Certificates suitable for 1100 Volt.

NS 39.2 - Supplying and fixing of shock treatment chart written in English and Hindi duly framed in as required.

NS 39.3 - Supplying and fixing of first aid box as approved complete with standard kit as prescribed by Indian Red Cross.

NS 39.4 - Supply of Hand gloves made out of rubber suitable for 1100 volt grade

NS 39.5 - Supplying and fixing of a set of four nos. of fire bucket painted red and duly filled with sand conforming to IS: 2546-1974 complete with MS stand suitable for supporting four buckets (Pedestal type)

NS 39.6 -Supplying and fixing of 4.5 kgs. Capacity carbon dioxide type fire extinguisher of ISI approved make with wall mounting bracket as required.

NS 39.7 -Supplying and fixing of 4 kgs. Capacity ABC dry powder type fire extinguisher of ISI approved make with wall mounting bracket as required.

NS 40 -Providing, fixing, testing & commissioning of SS spring loaded air relief valve for pressure of 16 kg/sqm of approved quality with SS isolation valve, tapers, G.I. pipes and specials etc. including making necessary screwed/ flanged joints by providing all jointing materials including painting and testing the joints to hydraulic pressures specified for pipes all complete as per drawings and as directed by the Engineer-in-Charge.

25 mm dia

NS 41 - Providing and fixing Cast Carbon Steel / forged brass CS Ball valve (Hyd. Test pressure body 30 kg/cm2 & seat 21 kg/cm2) of the following size: (Cost inclusive of providing necessary union / flange connection).

50 mm dia

NS 42 - Providing & fixing indoor type hose lockable cabinet frames fabricated from 40 x 40 x 5 angle iron sections and 16 gauge MS sheet with full front glass door and locking arrangement, suitable to accommodate landing valves, 15 m long hoses, first-aid hose reel and branch pipe nozzle & fire mans’ axe. The cabinet frame shall be painted with one coat of primer and two or more coats of synthetic enamel paint of approved make and shade, as required (Approx 2.1 m (high) x 0.9 m (wide) ). The item shall be complete of MS housing with front door.(Cost shall be inclusive of providing break glass box containing key for the cabinet along with hammer).

NS 43 - Providing and fixing standard firemans axe with heavy rubber handle.

NS 44 - Supply, Installation, Testing and Commissioning of Electrical Control Panel in common cubicle with suitable compatmentation for Booster Pumps as per requirment of the drives and with auto on/off logic and operational sequence as per specifications with all meterial, accessories, instrumentation etc.complete.( GA drawing including circuit diagram shall be submitted by the contractor and to be approved by Eingineer-in-charge.

NS 45 - Providing & fixing 150 mm dial type Pressure gauge of (0-16kg/cm2) range with gun metal shut off cock etc. duly calibrated before installation in MKS and FPS units and fixing the same where required as directed including all fittings, short piece, nipples, elbows testing the joints etc.all complete. (Quantity of this item will be payable only where it has not been included in the relevant composite items).

Bidder Name

Amount

Shree Gautam Construction Co. Ltd.(GSTN-18AAGCS4032F1ZJ)

JCICL(GSTN-NA)

Bidder Name

Amount

Shree Gautam Construction Co. Ltd.(GSTN-18AAGCS4032F1ZJ)

JCICL(GSTN-NA)

Bidder Name

Amount

Shree Gautam Construction Co. Ltd.(GSTN-18AAGCS4032F1ZJ)

JCICL(GSTN-NA)

JCICL

JCICL

JCICL

JCICL

Shree Gautam Construction Co. Ltd.

JCICL