PROVISION EXPANSION OF STORAGE ACCN BY ADDN / ALTN IN P-1 BLDG AND CERTAIN MINOR WORKS AT UNDER GE (I) RND KANCHANBAGH

Amount

Providing and fixing 15 mm nominal dia Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing for internal work on exposed on wall. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.

Providing and fixing 25 mm nominal dia Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing for internal work on exposed on wall. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.

S&F angle stop valves cast copper alloy, fancy type chromium plated, screwed down, high pressure with capastan heads, screwed both ends for iron pipe or for unions in 15 mm bore fixed complete all as specified.

Providing and fixing unplasticised P.V.C. connection pipe with PTMT Nuts, collar and bush of approved quality and colour.15 mm nominal bore with 45 cm length complete all as specified and directed by Engr-In- Charge.

S&F Bib taps, two way cast copper alloy chromium plated, fancy type with capastan heads, screwed down, screwed for iron pipe or for brass ferrule 15mm bore fixed complete all as specified.

S&F swan neck pillar tap for counter wash hand basin, fancy type, cast copper alloy with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks & fly nuts, screwed for iron pipes of 15mm bore complete all as specified. Cat part of Hindware F280001 or equivalent

S&F fancy type pillar tap cast copper alloy with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks & fly nuts, screwed for iron pipes of 15mm bore complete all as specified.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour.600 mm long towel rail with total length of 645 mm, width78 mm and effective height of 88 mm, weighing not less than 190 gms complete all as specified and directed by Engr-In- Charge.

Providing and fixing floor mounted, white vitreous china single piece, double traps syphonic water closet of approved brand/ make, shape, size and pattern including integrated white vitreous china cistern of capacity 10 litres with dual flushing system, including all fittings and fixtures with seat cover, cistern fittings, nuts, bolts and gasket etc including making connection with the P/S trap, complete in all respect as per directions of Engineer-in-Charge.

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge.

S&F 32mm dia PVC flexible waste pipe of length exceeding 60cm but not exceeding 90cm with connector suitable to connect the pipes with waste fitting/ coupling of WHB/ sink/ urinal complete.

Providing and fixing White Vitreous China Flat back wash basin size 550x 400 mm with single 15 mm C.P. brass pillar tap with C.I. brackets, , 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required incl dismantalling complete all as specified and directed.

S&F in vitreous china oval counter wash hand basin white of size 56x41 cm excluding taps, waste chain and porcelain plug but including brackets, CP waste fittings 32mm dia including cutting for and pinning in ends of brackets or erecting stand complete all as specified and directed.

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink with drain board of size 510x1040 mm bowl depth 250 mm as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required complete all as specified and directed.

S&F PVC (SWR) pipes,75 bore of pipe, single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified.

S&F PVC (SWR) pipes,75 bore of pipe, single socketed, in any length with rubber ring joints, fixed to wall complete all as specified.

S&F 75mm PVC (SWR) bends any radius complete all as directed.

S&F 75mm PVC (SWR) single Y junction any radius complete all as directed.

S&F 75mm PVC (SWR) single T junction any radius complete all as directed.

S&F 75mm PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as directed.

Providing and fixing powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately)

Providing and fixing powder coated aluminium (minimum thickness of powder coating 50 micron) for for partitions including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately)

Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge. With stainless steel cover plate minimum 1.25 mm thickness complete all as directed.

Providing and fixing Brass 100mm mortice latch and lock with 6 levers without pair of handles (best make of approved quality) for aluminium doors including necessary cutting and making good etc. Complete all as directed.

Providing and fixing 125mm long aluminium handles, ISI marked, powder coated as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete all as directed.

Providing and fixing 250mm long aluminium tower bolts, ISI marked, powder coated as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete all as directed.

Providing and fixing 300mm long aluminium sliding door bolts, ISI marked powder coated as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete all as directed.

Providing and fixing glazing in door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 4.0 mm thickness (weight not less than 10kg/sqm) as directed by Engineer-in-charge.

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. Pre-laminated particle board with decorative lamination on both sides complete as per architectural drawings and directions of Engineer-in-charge. .

S&F solar control film 25 micron reflective type sticked to glass panes as per instructions of manufacturers complete all as specified and directed.

S&F Solid PVC Wall Lining consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications.

S&F 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification.

Providing and laying autoclaved aerated cement blocks masonry with 150mm to 300 mm thick AAC blocks in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in-Charge.

M & L rendering 12 mm thick in CM 1:4 on fair faces of brick work or concrete , finished even and smooth without using extra cement complete all as specified.

M&L for Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade new work (two or more coats) over and including water thinnable priming coat with cement primer over a coat of 1 mm thick wallputty to make surfaces smooth complete all as specified.

Dismantling tile work in floors and walls laid in cement mortar including stacking material within 50 metres lead for thickness of tiles 10 mm to 25 mm all as directed.

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick bed of cement mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sq.m including pointing the joints with white cement and matching pigments etc., complete all as specified and directed.

Providing and fixing 1st quality ceramic glazed tiles size 450x350mm conforming to IS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

Providing and fixing 18mm thick both sides Pre-laminated cement bonded wood particle board as per IS : 15786:2008 of approved brand and shade with suitable full threaded steel screws etc. in partitions, boxes, shelves, racks and cupboard, kitchen cabinet under kitchen counter etc. all complete as per direction of Engineer-in-charge (Note: Fittings to be paid separately).

M & L for PVC (edge beading) lipping of suitable width fixed to exposed edges of 19mm thick plywood of approved quality and colour to match the laminate sheet fixed with approved adhesive all as specified and directed.

Providing and fixing bright finished brass handles with screws etc. complete125 mm long all as specified and directed

Providing and fixing 50mm special quality chromium plated brass cupboard locks with six levers of approved quality including necessary screws etc. complete

Providing M.S. Piano hinges ISI marked IS : 3818 finished with nickel plating overall width 35 mm and fixing with necessary screws etc ., complete.

Providing and fixing magnetic catcher of approved quality in cupboard / ward robe shutters, Double strip (horizontal type) including fixing with necessary screws etc. complete.

Providing and laying Polished Granite stone flooring Polished Granite stone slab of all colour and texture except , Cherry/Ruby Red in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge.

Earth work in excavation in All kinds of soil. by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.

Providing and laying PCC 1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources).

Hardcore of gauge exc 63 mm but n exc. 100 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rolled/rammed to a true surface

Brick work with clay flyash F.P.S. (non modular) brick of class designation 7.5 in superstructure above plinth level up to floor five level in Cement mortar 1:6 (1 cement : 6 coarse sand)

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Removing excavated soil to a distance n.exceeding 50m and depositing where directed at level n.exc 1.5m above starting pont complete all as specified and directed

Centering and shuttering including strutting, propping etc. and removal of form work for Foundations, footings, bases for columns

-ditto - but as in Columns, piers, abutments, pillars, posts and struts

Providing and laying in position ready mixed or site batched design mix cement Concrete of M25 grade with minimum cement content of 330 kg /cum for reinforced cement concrete work as in foundattion using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete.

-Ditto -as above but as in retaining wall, columns, lintel beams ic above plinth level

Steel reinforcement Thermo-Mechanically Treated bars of grade Fe-500D or more for R.C.C. work including straightening, cutting,bending, placing in position and binding all complete upto plinth level

Steel reinforcement for R.C.C. work ready to use "cut and bend" rebars of approved make from factory/workshop to construction site including placing in position and binding all complete above plinth level. 5.22C.1 Thermo-Mechanically Treated bars of grade Fe-500D or more

Providing and fixing G.I. wire of dia. 4 mm, PVC coated to achieve outer dia not less than 5 mm in required colour and shade of required width in mesh size 50x50 mm including strengthening with 2 mm dia wire or nuts, bolts and washers as required complete as per the direction of Engineer-in-charge.

Supplying at site Angle iron post & strut of required size including bottom to be split and bent at right angle in opposite direction for 10 cm length and drilling holes upto 10 mm dia. etc. complete

S&F Steel work welded in gratings, frames, guard bar, ladder, railings, brackets, gates and similar works built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required conforming to Fe-410-0 or Fe-310-0

White washing with lime to give an even shade on New work (three or more coats)

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade Two or more coats on new work With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/steel works

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes 110mm dia conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.

Demolition unreinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed

Demolition of brick work or stone masonary built in cement mortar or lime mortar including all quoins arches, pillars etc complete all as spd & directed

Excavating in trenches, n exc 1.5 m wide and n exc 1.5m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sqm on plan and getting out in Hard/Dense soil complete all as specified and directed

M/L Plain Cement concrete Type D2 1:4:8 (40 mm graded aggregate) as in foundations, filling and mass-concrete

M&L for brick work with sub class B Brick straight or curved on plan to any redius in half brick thick walls built in CM 1:4 Complete

M&L for plain cement concrete 1:2:4 type B1 (using 20mm graded stone aggregate) as in coping etc including necessary formwork and finishing exposed surfaces fair and even complete all as specified and as directed.

Returning, filling in including spreading, leveling, watering and well ramming in layers n exc. 25 cm as in soil complete all as specified and directed

Removing excavated soil to a distance n.exceeding 50m and depositing where directed at level n.exc 1.5m above starting pont complete all as specified and directed

Taking down cement plaster/cement lime plasters of bk work on any description including racking out of joints and cleaning dust etc complete all as specified and directed

M/L for rendering 15mm thick in CM 1:6 on other than fair faces of brick/conc surfaces face of wall, finished even & fair

M/L for rendering 15mm thick in CM 1:4 on other than fair faces of brick/conc surfaces face of wall, finished even & fair

M/L for rendering 10mm thick in CM 1:3 on other than fair faces of brick/conc surfaces face of ceiling, finished even & fair

M&L for preparation of New plastered surface of wall by complete removal & prepararion of surface and applying two coat of oil bond distemper incl preparation of surfaces with Birla putty over one coat primer etc all as specified and directed by Engr-in-Charge

M&L for Preparing old plastered surfaces and applying two coats of distemper oil emulsion including on one coat walls over a coat of wall putty to make surfaces smooth.

M&L for preparation of New plastered surface of ceilingl by complete removal & prepararion of surface and applying two coat of white wash all as specified and directed by Engr-in-Charge

M&L for preparation of old ceiling surface by complete removal & prepararion of surface and applying two coat white wash all as specified and directed by Engr-in-Charge

M&L for Preparing old plastered surfaces and applying two coats of cement base paint one coat of alkali resistan paint walls over a coat of wall putty to make surfaces smooth.

M&L for Preparing new plastered surfaces and applying two coats of cement base paint one coat of alkali resistan paint walls over a coat of wall putty to make surfaces smooth.

Taking down chowkhat with shutters (without taking off shutters from the frame) exc 1.50 sqm each but n. exc 4 sqm each.

Taking down chowkhat with shutters (without taking off shutters from the frame) n.exc 1.50 sqm each .

M & L 105x60mm x1.2mm thick Pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed

Supply & fixing of UPVC windows three track sliding window with two glazed and one wire mesh sliding shutters of profile width of frame 50 mm to 60 mm, limit thermal conductivity to l.3 Kcal/sqm/hr centigrade, sound insulation up to 4-0 bds, Density, 1.46 gm/ml, Tenstile strength - 43.9N/sqmm, % Elongation at break - 215, Tenstile mpduls - 2840N/Sqmm, Flexural strength - 51N/sqmm, Heat aging at 150 degrees - No surface defect, Thickness - 2 mm, Flexural moduls elasticity 2200N / sqmm, double baskets & wool pile on window, multi point gear locking at different sides of frame, anti lift device on slide windows with temper proof screws with and including glazed shutter fixed with 5 mm thick plain sheet glass & wire mesh shutter with stain less steel wire cloth 304 grade stainless steel with 0.254 mm (30 gauge) dia of steel wire and 0.95 mm width of aperature and filling gap of wall and frame with silicon sealent complete incl taking down old down old window complete all as specified. all as directed .Area Not Exc 2.00 Sqm.

S & F 5.5mm Sheet glass area exc 0.5 sq. m in each pane

M&L Vitrified Ceramic light shade tiles 9 to 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match flooring( in any pattern) and jointed with coloured cement matching with surfaces of tiles as in floor 15 mm thick cement screed in CM 1:6 and pointed with coloured cement matching with surfaces of tiles as in floor & veertical surface complete all as specified and directed complete all as specified and directed

M & L Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240

S & F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

S & F 40mm Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides

M & L for proividing two coaat of synthetic enamel paint over one coat of red oxide primer Surfaces of any description, over 10cm in width or girth,not otherwise described

Laying 100mm sand , spread, rolled and consolidated to gradient and camber required

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc. and making good, cutting exceeding 20cm girth

S & F 150 mm aluminium anodised barrel tower bolt of extruded section.

S&F mild steel butt hinges, medium weight, size 100mm with ISI mark.

S&F annodised aluminium handle, fabricated type of size 150mm.

M & L Surfaces of any description, not otherwise descri-bed, over 10cm width or girth 17002 Ditto,

S & F for gypsum board 12mm thick in ceiling at different levels (Sunk & Raised) type of approved design fixed with screws as manufactures instructions including demolition of existing false ceiling complete all as specified and directed.

S & F Gl frame work for seamlessceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel including Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified

Hardcore of broken bricks gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface

M & L for plain cement concrete(1:3:6) type C-2 (using 40 mm graded stone aggregate) of 100 mm thick as in Path / PCC floor, finished even and fair including demolition of existing concrete complete all as directed.

S&F Steel rolling shutters 1.25 mm lath thickness, Steel rolling shutters, with out ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated, complete but motorised type rolling shutter of size exceeding 32 sqm but not exceeding 40 Sqm including taking down of existing shutter along with connected to gear box, shaft etc, complete all as directed.

Supply only electric motor of 2.00 HP capacity suitble for rolling shutter of size exceeding 30 sqm but not exceeding 40 Sqm, single phase power, automatic stop level, thermostat for cooling motor and chain crank of 3 - 6mtr length in the absence of power all built in one single unit and shaft pipe of 150mm bore dia, including taking down of existing shutter along with conventional motor and connected to gear box, shaft etc and refixing shutter in same position, complete all as directed.

Dismantling aluminium/ Gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of serviceable material and stacking of serviceable material with in 50 meters lead as directed by Engineer-in-charge.

Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main "T" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc.

Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge.12.5 mm thick fully Perforated Gypsum Board tile made from plasterboard having glass fibre conforming to IS: 2095 part I, of size 595x595 mm, having perforation of 9.7x9.7 mm at 19.4 mm c/c with center borders of 48 mm and the side borders of 30 mm, backed with non woven tissue on the back side, having an NRC (Noise Reduction Coefficient) of 0.79, with 50 mm resin bonded glass wool backing.

Point wiring with 1.5 Sq.mmm copper conductor FRLS (multistranded) PVC insulated ISI marked unsheathed cable of any length drawn in and including concealed non metallic rigid PVC conduit of not less than 25mm dia ISI marked with all fitting and other accessories and also including PVC insulated ISI marked unsheathed FRLS cable size 1.5 sqmm copper conductor as earth wire to common earth dolly including galvanised terminal boxes ISI marked fixing into the wall of sizes as required at site and modular plates and frame suitable for fixing switches / sockets / fan regulators etc, and making good the disturbed surfaces matching to the existing surface for one light point/fan point/bell point controlled by one way modular switch 5 Amps 240 volts, complete all as specified and directed

One 3 pin socket outlet 5 Amps on the same board with other switches.

All as per SI Item No. 2 here-in-before but wiring with 4 Sqmm for 15 Amps modular 3 pin socket outlet on independent board / two pin earth plug and socket including providing 4 Sq.mm PVC insulated multistranded unsheathed FRLS copper earth continuity conductor and connected to common earth dolly, complete all as specified and directed.

Supply & Fixing Modular switch, one module, one way 6 Amp, 240V, complete all as specified and directed.

Supply & Fixing Modular switch 16A, one way, one module, 240 Volts, complete all as specified and directed.

Supply & Fixing Modular step type, electronic fan regulator, two module, 240 Volts, complete all as specified and directed.

Supply & Fixing modular socket one way 6 Amps, 2/3 pin combination 2 module, complete all as specified and directed.

Supply & Fixing modular socket, 6A/16A - 2 /3 pin combination 2 module, complete all as specified and directed.

S&F ceiling rose two to three terminal surface backallite type AC 50Hz 230 volts complete

S&F 1x20W,230V, 6500K CCT surface mounted integral LED batten with extruded aluminium housing with inbuilt electronic driver, polycarbonate diffuser including connecting up with twin core twisted flexible copper condctor cable from ceiling rose to fitting all as specified. Make : Havells cat part No. ENDURALINEARNEOBS20WLED865SPCSS or equivalent in Philips/Wipro

Supply and fixing 240V, 10 KA 'c' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 5 to 32 AMP, in the MCB DB Complete with connection testing and commissioning.

Supply and fixing factory made epoxy powder coated Distribution Board SPN 08 way double door ( MCB DB ) MCB DP as In comer, with 100 Amp bus bar, metal door (IP-43 protection, IK-09)as per IES-61439-3 fabricated from CRCA sheet and fixed semi flush to wall and suitable for universal mounting and neutral bar, standard DIN rail, Earth bar and cable ties for cable management, top and bottom removable gland plates with Knockout semi flush to wall and making good disturbed surface and touch up with the same finishes complete complete all as specified Note: MCBs will be measured and paid seperately under respective Sch A item in the schedule

M&L sub main wiring with PVC insulated FRLS grade cable LT 1100 Volts grade PVC insulated unsheathed, multistranded with stranded copper conductor drawn in & including concealed type medium grade PVC conduit not less than 20mm ISI marked with all accessories and incl cuttting and chasing of any type of wall and making good to match with the existing surfaces alongwith one contineous earth wire and connected to common earth complete all as specified for following sizes of cable :-

2 x 2.5 sq mm with one continous earth wire of size 2.5 sq mm Note : 2 runs of 2.5 sq mm cable and one run of 2.5 sq mm earth wire and PVC conduit will be measured as one meter.

2 x 4 sq mm with one continous earth wire of size 4.0 sq mm Note : 2 runs of 4 sq mm cable and one run of 4.0 sq mm earth wire and PVC conduit will be measured as one meter.

Supply and fixing amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of 2 pole and 63 amps current carrying capacity in the MCB DB complete with connection testing and commissioning.

Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CM/M/W) minimum 6.00, Air delivery minimum 210 Cum/Min , 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC supply earthing complete all as directed.

Material & Labour for steel tubing, medium grade, ISI marked, galvanised including short lengths, laid in trenches, complete with all fittings (such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps, plugs and unions etc.,) 25mm bore of pipe, complete all as specified and directed. NOTE:- Excavation and earth work required for above item shall be measured and paid seperately.

Material & Labour for Gun-metal, globe or gate valves, conforming to IS 778, with iron wheel head, screwed both ends for iron pipe and fixed, 25mm bore of pipe, complete all as specified and directed.

Making connection of G.I. distribution branch with G.I. main of 50 to 80 mm nominal bore by providing and fixing tee, including cutting and threading the pipe etc. complete as required at site

Excavating in trenches, not exceeding 1.5 m wide and not exceeding 1.5metre in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, tubular poles or laying of pipes, or for removal / laying of cables etc., not exceeding 10 sq m on plan and not exceeding 1.5 m in depth and getting out in hard/dense soil, including trimming sides of foundations and forming bottom surface to required level, complete all as specified and directed by engr in charge.

Supply, installing, testing and commissioning of 1.5TR capacity Split type air conditioner unit (Inverter type) 5 star rated complete with drive motor, air cooled condenser with all accessories varied speed and dual rotary compressor, including fixing the outdoor unit with powder coated MS stand/PCC base and fixing of indoor unit on wall including core cutting of required size on type of wall and making good of disturb surface, providing and making interconnection, including refrigerant piping with nitryle rubber insulation and control cable from indoor to outdoor up to a distance of 3.0 mtrs, power cabling (max 3.0 mtrs from isolator/enclosure) to units, first charging non CFC/non HCFC R-32 of refrigerant gas including cord less remote, PVC drain pipe of 25mm dia for connecting drain lines from indoor unit to maximum of 3.0 mtrs to nearest drain points complete all as specified and as directed.

Supply and fix Voltage stabilizer for automatic operation, single phase naturally air cooled indoor type & designed for input variation between 170 V to 250 V with output voltage stabilized at 230 V with accuracy of ± 2.5% and of capacity 4 KVA complete all as specified and as directed.

Material and labour for point wiring complete with 1.5 Sqmm single core PVC insulated FRLS unsheathed cable voltage up to and including 1100 volts grade multi-stranded copper conductor drawn through and including rigid PVC conduit medium grade 20mm or higher dia ISI marked as required at site including conduit accessories such as junction boxes, inspection covers etc, surface/concealed on brick masonry walls, roofs, floors etc by means of saddles and clips etc including cutting chasing and making good of disturbed surfaces to match existing surface where required and concealed galvanised box factory made of suitable size including modular plate as per number of switch modules required for fixing switches, sockets fan regulators etc of required size including provision of PVC insulated 1.5 Sqmm FRLS copper conductor cable as earth continuity conductor and connecting to common earth dolly all as specified and directed for the following:- One light/ fan point/exhaust point controlled by one, one way switch/bell push

All as per item No. 131 above but for 5 Amps socket on independent board

All as per item No. 131 above but for 5 Amps socket on same board

All as per item No. 131 above but wiring with 4.0 Sqmm for 15 Amps switch socket combination on independent board including providing 4.0 Sqmm PVC insulated FRLS unsheathed copper conductor cable as earth continuity conductor and connected to common earth dolly.

Supply and Fixing Modular switch single pole, one way 6 Amps one module all as specified and directed.

Supply and Fixing Modular switch single pole, one way 16 Amps one module all as specified and directed.

Supply and Fixing Modular socket 6 Amps multipurpose 2 in 1- 2/3 pin 2 module complete all as specified and directed.

Supply and Fixing Modular socket 6/16 Amps multipurpose 2 in 1 -2/3 5 pin 2 module complete all as specified and directed.

Supply and Fixing ceiling rose three terminals Poly carbonated isolated body complete all as specified and directed.

Supply and fix Industrial type LED luminaire 1x20W, aluminium housing with polycarbonate diffuser, with , 10% THD, lumen efficiency not less that 120 lm/watt complete with all accessories prewired and including connecting up with three core twister flexible copper conductor cable with suitable size complete removing unserviceable fittings all as specified and directed.

Supply and Fix MCB Distribution board, SPN 12 way sheet metal enclosure double door 415 volts, AC, factory made, fixed on wall suitable for mounting Isolators and MCBs with bus bars, neutral link and earth bar of following No. of ways including taking down unserviceable distribution board and making good to the disturbed surfaces of wall all as directed.

Supplying and fixing 63 Amp rating, double pole, 240 V,isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and Fixing MCB SP 6 to 32 Amps, 240 Volts 10 KA 'C' series complete all as specified and directed.

Supply & Fix sub main wiring with 2 run of 4 Sqmm single core FRLS PVC insulated unsheathed cable 1100 Volts grade multistranded with copper conductor (FRLS) drawn through and including non metallic rigid PVC conduit 25 mm dia including conduit accessories surface/concealed type on walls, roof, floors etc including one run of 4 Sqmm PVC copper conductor as earth continuity wire all as specified and directed.

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

GI earth wire of 6 mm dia fixed on walls/floor as earth continuity conductor connected to DBs/ panels etc.

Supply & fix ceiling fans complete with electronic type regulator and accessories 230 V,1200 mm sweep. BEE 5 star rated

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 6.0 sq mm 2 core

Supplying and fixing 20 A, 240 V, SPN Industrial type socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 20 A "C" curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissionin etc. as required.

Supply & fixing modular socket 16 A, two module 230 Volts ,multipurpose complete all as specified and directed

MOHAMMED GHOUSE (BID ID -3440493)

M.R.ENTERPRISES (BID ID -3439926)

Ravi Enterprises (BID ID -3438189)

SUN LIGHT HOUSE (BID ID -3438102)

WELDECOR (BID ID -3437853)

SRI SAI ENTERPRISES (BID ID -3437867)

Anjana corporation (BID ID -3439444)