Loading…
Loading…
Tender Value
₹16.0 Cr
EMD Value
₹32.0 L
Closing Date
7 Jul 2026, 3:00 pm
Provision of Indoor and Outdoor signalling work in connection with IBS at 05 Locations between BDKN-SLN, SLN-PKX, MBDP-PHV, RBL-RUM & RBL-GANG section, addition & alteration in existing Electronic Interlocking system at Sultanpur, Pakhrauli, Maa Belha Devi Dham Pratapgarh, Prithviganj, Rae-Bareli, Rupamau and Gangaganj stations and indoor signalling works at Bandhukalan station of Lucknow Division
287-SigC-I-LKO-T-01-26
287-SigC-I-LKO-T-01-26
Open
12 Months
Rae Bareli, Uttar Pradesh
₹0
₹32.0 L
15 Jun 2026
15 Jun 2026
23 Jun 2026
4 D e s c r i p t i o n : - Installation, wiring, programming, testing & commissioning i.c.w., Modification/alteration/augmentation in the existing EI system of Hot stand by Arc as per RDSO/SPN/192/2019 as per approved signalling plan with required materials/cards of EI with contractor own in connection with Provision of IBS in SLN-BDKN, SLN-PKX, MBDP-PHV, RBL-RUM and RBL-GANG section. All materials (Cards, wiring materials, communication equipments, Relays, connectors etc.,) if required for modification/Alteration/Augmentation must be supplied by the
required for modification/Alteration/Augmentation must be carried out by the contractor. This also includes supplies necessary for earthing the modified/Altered/ Augmented EI those needed for re- wiring external data-logger & Fuse Alarm system etc. Item also includes preparation of Selection Table, Locking Table, Control Panel and Route Section Plan, Wiring Diagram and other Diagrams (other technical documents if any) based on Signalling Plan supplied by Railways. Completion Documents as per special condition of contract. Note: 1. Jobs may be executed as per site condition nearly prior to commissioning. 2. These includes all hard copies of documents for each trainee which can be referred after training. Station: Sultanpur, Maa Belha Devi Dham Pratapgarh & Rae-Bareli Station. 4786279.4
1 DYCSTE-C-I-LKO-S AND T/NORTHERN RLY D e s c r i p t i o n : - Installation, wiring, programming, testing & commissioning i.c.w., Modification/alteration/augmentation in the existing EI system of Hot stand by Arc as per
contractor own in connection with provision of IBS in SLN-BDKN, SLN-PKX, MBDP-PHV, RBL-RUM and RBL-GANG section. All materials (Cards, wiring materials, communication equipments, Relays, connectors etc.,) if required for modification/Alteration/Augmentation must be supplied by the contactor & all activities (Designing, FAT, OEM Certificate, Drawing, Alteration in VDU & Panels etc.,) required for modification/Alteration/Augmentation must be carried out by the contractor. This also includes supplies necessary for earthing the modified/Altered/ Augmented EI those needed for re- wiring external data-logger & Fuse Alarm system etc. Item also includes preparation of Selection Table, Locking Table, Control Panel and Route Section Plan, Wiring Diagram and other Diagrams (other technical documents if any) based on Signalling Plan supplied by Railways. Completion Documents as per special condition of contract. Note: 1. Jobs may be executed as per site condition nearly prior to commissioning. 2. These includes all hard copies of documents for each trainee which can be referred after training. Station: Pakhrauli, Prithviganj , Rupamau & Gangaganj Stations.
Description:- Design of the PI/EI/IBS system complete including selection table, Logic/interface circuit diagram, contact analysis chart, CT/Relay rack chart etc., preparation of Panel/VDU layout diagram, (circuit shall be designed by the contractor with the use of Q series relays) on the basis of approved signal Interlocking plan and obtaining approval of Competent Authority. The VDU layout
Railway specifications and as per latest rules prescribed by Rly. Drafting & supply of document shall be as per following details: (i) Supply of 6 copies of complete set of superior quality paper including one set laminated, properly bound in file with cushioned cover. (ii) Software backup of complete set in the form of CD (2 Nos.). (iii) One complete set of tracings. (iv) Design through CAD. (v) Drawings in A-3 size & plan in bigger size papers. (six sets)
IBS, Resistance, condenser, soldering material etc., to be arranged by the contractor. (For Bandhu Kalan station)
54x34mm complete wired up each domino unit should have all the 15-contact terminal wired up. Inspection: Consignee.
6 Description:- Supply of panel indication LED Red, Green, Yellow, Clear etc. Inspection: Consignee.
7 Description:- Supply of Veeder Counter for panel 24 V DC, 23.3mA. Inspection: Consignee.
Description:- Design fabrication, supply, fixing & wiring of Block indication panel made of 16 SWG powder coated MS sheet of size 39cmx24cmx15cm appx. Consisting of buzzer, counter & different
approved by site incharge. Indication on the panel & all description on front panel should screen printed. The indication on the front face of the panel will be based on site condition which will be advised by site incharge, which has to confirm before carrying out the work of screen painting. All materials to be supplied by contractor.
Description:- Supply of Relay, Non-AC immune, plug in type, style QN1, DC neutral line relay, 24 V
connectors confirming to BRS:931A, IRS:S-45/47/44, IRS:S-45/47/68 & IRS:S-23/88 as applicable. The interlocking code for this unit shall be ABCDF or latest. Inspection: RDSO.
Description:- Supply of Relay AC immune, plug in type, style QNA1, DC neutral line relay, 24 V DC
confirming to BRS:931A, IRS:S-45/47/44, IRS:S-45/47/68 & IRS:S-23/88 as applicable. The interlocking code for this unit shall be ABDGH or latest. Inspection: RDSO.
Description:- Fabrication, supply and fixing of relay racks of size 2200mmx690mm (as per approved Drg. No. NR/S&T/CON/4.3/97A) made of angle iron size 45mmx45mmx6mm alongwith outer frame made of angle iron size 65mmx65mmx8mm, fitted with M.S. squares bars duly
units/ECRs/HMUs. All fixing material like antilting device, hylam sheets if required, bolts & nuts, washers, insulators, shoe, angle irons, flats, L-bolts, Catenary wires and cement concrete etc. will be supplied by the contractor. This includes cleaning, priming by red oxide, painting & description etc. with ISI mark paints.
DYCSTE-C-I-LKO-S AND T/NORTHERN RLY Description:- Fabrication, supply and fixing of cable termination board of size 2200mmx900mm as per Drg. No. NR/S&T/CON/4.1/97A made of angel iron size 40mmx40mmx5mm along with outer frame made of angle iron size 65mmx65mmx8mm duly fitted with Bakelite sheet (HYLAM MAKE or similar) of size 6mm thick. This also includes fixing of ARA terminals/strips/Wago connectors & fuse
jamming of armour of cables, each cable in the hole drilled separately for each cable through the salwood plank and all cable entry points on location boxes, location huts, JBs relay room/battery room to be closed with suitable masonry Works covered with sand and plastering. All the fixing materials like bolts, nuts, washers, Insulators, shoe, angle irons, flats, L- bolts, Catenary wires & cement concretes etc. will be supplied by the contractor. This includes cleaning, priming by red oxide, painting & description etc. with ISI mark paints.
Description:- Fabrication, supply and fixing of scaffolding /cable carrier made of angle iron of Size
between two flats will be 25cm or less as per site requirements all the fixing materials i.e., nut, bolt washer, insulators, cement concrete etc., will be supplied by the contractor. This includes insulating flat strips, cleaning priming by Red oxide, painting by ISI mark paint.
materials) as per IRS spec. No. IRS-76/89 with amendment no.3 or latest. (From RDSO Approved Source only). Inspection: RDSO.
conductivity PVC insulated unarmored as per Spec. no. IRS-S/76/89 (Amd 3) or latest amendment. (From RDSO Approved Source only). Inspection: RDSO.
Description:- Wiring of relays in relay room/relay huts as per approved wiring diagrams. All wiring
(Supply of cables & wires covered separately). It also includes dressing, bunching, lacing and fixing of relay bases.
Description:- Supply of electric fuse complete with fuse block(base) for Railway signalling non-
and fuse block made of PBT/Polycarbonate as per IRS: S-75/2006 (Rev.2 & Amd.2) and drg no. 23748 (IRS), Alt-4 or latest. Fuse block shall be suitable for round head type fuses. Inspection: RDSO.
Description:- Supply, installation & wiring of Earth leakage detector (12 Channel) for monitoring
no.RDSO/SPN/256/2002 or latest and stipulations of tender document. Inspection: RDSO for supply portion.
Description:- Supply of Portable digital auto range multi-meter clamp type Philips, Motwani, Fluke
600V(AC/DC) and 0.1 ohms- 40M ohms suitable for measurement of Freq., capacitance complete with Manual, leads, battery and holster etc. Inspection: Consignee.
Description:- Supply of tool kit for JE/SE/SSE for Maintenance as per tech spec. given below: (1) Digital Multi Meter suitable for axle counter ranges 20 Amp AC/DC make protek 506 or similar- 1 no. (2) Digital clamp Multi Meter range up to 100 Amps for AC/DC current make SEW or similar - 1 no. (3) Leather Tool Bag for keeping tool kit -1 no. (4) Plier Sealing with sealing code bit -1 no. (5) Plier Wire Cutting 8" make Taparia or similar -1 no. (6) Nose Plier 4" make Taparia or similar -1 no. (7) Wire
(10) Soldering Iron 230V AC/65 watt -1 no. (11) Soldering Iron 230V AC/35 watt with different type replacement soldering head - 1 no. (12) Soldering Iron 110V AC/35-watt -1 no. (13) Measuring Tape steel 30 meters - 1 no. (14) Measuring Tape steel 3 meters - 1 no. (15) Rechargeable Torch Superior quality -1 no. (16) File Flat 8" long - 2 nos. (17) File Round smooth 8" long - 2 nos. (18) File Flat Bestirred 8" long - 2 nos. (19) Electric Drill Machine Portable 6mm make wolf or similar -1 no. (Inspection: Consignee)
21 DYCSTE-C-I-LKO-S AND T/NORTHERN RLY 21 Description:- Supply fixing and wiring of Fuse Auto Changeover System (FACS main system) as per RDSO/SPN/209/2012 Rev. 2.0 with latest amendments. One automatic changeover unit comprise 32 nos of external Non-Deteriorating Type or 'G' type fuses of various Ampere Rating, working voltage-
fuses in one card. Installation, wiring, Testing and commissioning of Fuse Alarm System, it consists of fixing of modules of fuse alarm system on existing relay rack, wiring from existing fuses to modules, soldering, lacing etc. working to be executed without affecting the functioning of the existing Circuits/Gears and the work shall be supplied by the contractor. Inspection: RDSO for supply portion.
Description:- Supply of 4 conductor dis-connect terminal block for test and measurement 0.8
carrier rail DIN 35 front entry cage clamp connection Grey wago or similar as RDSO/SPN/189/2004 Rev. 3.0 or latest. Inspection: RDSO.
Wago or similar as per RDSO/SPN/189/2004 Rev. 3.0 or latest. Inspection: Consignee.
RDSO/SPN/189/2004 Rev. 3.0 or latest. Inspection: Consignee.
similar as per RDSO/SPN/189/2004 Rev. 3.0 or latest. Inspection: Consignee.
Description:- Fabrication, wiring and supply of simulation panel as per drawing no. SSTE/PS/1562
bases shall be supplied by Railway. All materials such as on/off/2way switches, wires, strips & tag blocks etc. to be supplied by the contractor. (Only indoor cables for wiring between relay room and simulation panel shall be supplied by Railways).
Description:- Fabrication, wiring and supply of lamp board as per drawing no. SSTE/PS/1563
strips, tag blocks, lamps & holders etc. including sufficient lamps for testing to be supplied by the contractor. (Only cables for wiring between relay room and lamp board shall be supplied by Railways).
Description:- Supply, installation, testing, networking & commissioning of Data Logger with 512 Digital and 32 Analog inputs as per RDSO Spec IRS-S-99/2006, Amd.3 with latest amendments
Protocol converter & PC (HP S01-AD0104IN or equivalent) along with B & W A-4 size laser printer. The requisite communication Cable/Channel for networking will be arranged by Railway. Inspection: RDSO for supply portion.
Description:- Installation, wiring and testing of Integrated Power Supply System. This includes power distribution connection to bus bar and relay racks in the room and fabrication and fixing of AC/DC power distribution board made on 10mm thick Phenolic laminated sheets or any standard make with connections suitable for 32 Amp. as per site requirement. Wiring to be done with flexible
distribution board to Integrated Power Supply system. Wiring to be done with Flexible Cable, Single core, multi strand 10sq mm. as per spec IRS 76/89 with latest amendment from integrated power supply system to D.C. bus bar. All connections as per site requirement to be arranged by contractor as per RDSO guidelines and instruction of railway engineer at site. This item includes fixing of ladder along the wall for carrying of power supply wires/cables from IPS room to relay room/ power room / Battery room etc.
33 DYCSTE-C-I-LKO-S AND T/NORTHERN RLY 33 Description:- Supply of 3 phase Manual changeover switch 63Amps/100Amps. Siemens/ Havells or similar Iron Clad switch. Inspection: Consignee.
supplies to the SSDACs in compliance to Railway board's Policy guidelines.
Description:- Preparation of cable route plan, Cable core chart, Power supply arrangement plan for indoor and outdoor, Cable termination chart in relay room and location boxes, Location wiring plan, Cable insulation chart and register, Track circuit history card, Fuse analysis plan, Equipment disposition plan, Track circuit jumpering plan, Terminal and Contact analysis chart, Outdoor circuits,
SLN-BDKN, SLN-PKX, MBDP-PHV, RBL-RUM and RBL-GANG section and other outdoor diagram and obtaining approval of the Engineer as per following: - (i) Supply of 6 copies of completion set of superior quality paper, laminated, properly bound in steel clip jaw file with cushioned cover. (ii) Software back up of complete set in the form of CDs. (iii) One complete set of tracings. (iv) Design through CAD. (v) Drawings in A3 & plans in bigger size. (six sets).
Description:- Excavating and refilling of trench in Normal Soil to the level of ground with rammed
both side of the station alongside the track. It shall conform to the safe distance as per signalling and cable plan. It also includes clearance of roots of trees & bushes. 1424000.0
0 38 Description:- Supply and laying of 2nd class bricks in the trench and laying as per Drg. No. (NR/S&T/Con./1.1/97A) and as per instruction of the site Engineer.
SDO/Cable Laying/020, dt.31.10.11. The marker shall be fixed at various places of cable route as per instruction of Eng. at site.
Description:- Supply and installation of RFID Electronic Marker for S&T underground cable with
diameter with floating coil to keep detection circuit always Horizontal for better detection) which can be buried to depth of 5 ft. Placing in trench. Inspection by RITES for supply portion.
Description:- Supply of 3M/ or similar make integrated Dynatel Electronic Cable/Pipe/Route Tracer /Locator (with inbuilt marker locator) high power 12 w transmitter for effective long distance locating, 6 active locating frequencies (577 Hz, 1 KHz, 8kHz, 33 kHz, 82 kHz, 200 kHz), depth range
and receiver, super induction mode, with capability of Electronic marker locating (both passive and RFID) and cable route locating in a single equipment, receiver with Bluetooth wireless technology, GPS interface (internal, 3m) allows software to be downloaded from website, weight less than 2.5 Kgs for Transmitter as well as receiver, Signal current measurement in cable, (Model No. 2550XID). Inspection by RITES.
pitched/stone/bricks paved surface, road/crossing/platform etc., and restoring the surface to its original condition.
Description:- Supply & installation of HDPE double Wall Corrugated (DWC) Pipe as per as per RDSO Specification No. RDSO/SPN/204/2011 Ver. 1.1 With Amndt-1 (Outer dia 120mm in 6m st. length with
secure the pipe as per specifications, drawings and stipulations of tender documents and as per approved cable route plan including road crossing/platform/track crossing and for bridges and culverts etc. Inspection: Consignee for supply portion.
Description:- Supply and fixing of G.I. pipe 75mm dia, 3mm thick as per spec no IS-1239,
suitably concreted at both ends as per approved drg. No.Drg. No.NR/S&T/CON/1-4/97.or at ASM office/other buildings suitably fixing it to the wall and at both ends. G.I. clamps of M.S. flats bolts and nut, to be supplied by the contractor. Inspection: RITES for supply portion.
45 DYCSTE-C-I-LKO-S AND T/NORTHERN RLY
signalling / telecom /power cable under track/road/culvert etc., cable laying is covered separately.
Description:- All work of horizontal boring and trenchless cabling along with supply,transpotation and insertion of double wall corrugated pipe -(ISI marked ) conforming to RDSO Spec no.
instruction of site engg. by using pipe of size 120 mm outer dia, 103.5 mm inner dia in which required number of cables to be crossed. The depth of horizontal boring should be minimum 1.0 mtr. from rail flange/road level. Inspection: RITES for supply portion.
NR/S&T/CON/1-1/97C and as per cable route plan approved by Railways and meggering of cable before and after its laying of all type of outdoor cables.
Description:- Testing & meggering of all types of outdoor cables after its laying and termination on
for core to core and core to earth on prescribed proforma for each core of the cable separately after termination of cable. This also includes dressing & lacing of cable on both ends. Performa for testing & material for lacing to be supplied by the contractor.
Description:- Casting, concreting and curing of foundation and erection of apparatus case single as per Drg. No.NR/S&T/Con./2.7/97. A layer of 3mm of Bitumin compound has to be provided between
as cement, sand, aggregate & anchor bolts shall be supplied by the contractor. Contractor is required to execute all type of repair work of foundation if required during inserting the cable for termination.
handle as per Drg No. RE/S&T/ALD/SK/219/82 & 221/82 with Alt.B. Inspection: RITES.
Description:- Preparation of App. Case single involving wiring of relays: Preparation & fixing of Bakelite hylum sheet 910x800x6mm and Bakelite shelf 900x450x25mm duly fixed by angle iron piece of different size inside all the app. Cases. Hylum board shall be fixed on an angle iron frame of 25mmx25mmx3mm. Angle iron frame will be fixed in location boxes secured by nuts and bolts. This includes fixing of fuses, ARA terminal, Q series relays and other type relays on square bars fixing and jamming of cables with 2-inch thick salwood plank provided at the bottom. This will include
through the salwood plank and all cable entry points on location boxes, location huts, JBs relay room/battery room to be closed with suitable masonry Works covered with sand and plastering. Wiring description for terminal drawing of circuits, inside app. Case. Painting from outside as well inside with red oxide and aluminum paint is covered separately. Size of lettering will be 100mm or as per instructions of Engineer at site. All materials including Bakelite shelf, hylum board, salwood plank, wire and wiring material, non-deteriorating type HRC fuses with bases, catenary wires, nuts and bolts and other items shall be supplied by the contractor and shall be as per the RDSO specn.(as applicable). Relays, ARA terminals only shall be supplied by the Railways.
Description:- Preparation of App. Case single not involving wiring of relays: Preparation & fixing of Bakelite hylum sheet 910x800x6mm and Bakelite shelf 900x450x25mm duly fixed by angle iron piece of different size inside all the app. Cases. Hylum board shall be fixed on an angle iron frame of 25mmx25mmx3mm. Angle iron frame will be fixed in location boxes secured by nuts and bolts. This includes fixing of fuses, ARA terminal, fixing and jamming of cables with 2-inch thick salwood plank provided at the bottom. This will include opening, pasting and jamming armour of each cable in the
location boxes, location huts, JBs relay room/battery room to be closed with suitable masonry Works covered with sand and plastering. Wiring description for terminal drawing of circuits, inside app. Case. Painting from outside as well inside with red oxide and aluminum paint is covered separately. Size of lettering will be 100mm or as per instructions of Engineer at site. All materials including Backelite shelf, hylum board, salwood plank, wire and wiring material, non-deteriorating type HRC fuses with bases, catenary wires, nuts and bolts and other items shall be supplied by the contractor and shall be as per the RDSO specn.(as applicable). ARA terminals only shall be supplied by the Railways.
53 DYCSTE-C-I-LKO-S AND T/NORTHERN RLY 53 Description:- Casting, concreting and curing of foundation and erection of half apparatus cases of size (670mmx760mm) and 650mm deep as per Drg.No.NR/S&T/CON/2.8/97. A layer of 3 mm of bitumen compound has to be provided between foundation and location box to prevent ingress of water in the base of location box. All material such as cement, coarse sand, aggregate and anchor bolt shall be supplied by contractor. App. Case half will be supplied by Railway. Contractor is required to execute all type of repair Works of foundations if required during inserting the cable for termination.
handle as per Drg No. RE/S&T/ALD/SK/220/82 & 221/82 with Alt.B. Inspection: RITES.
Description:- Preparation of App. Case half involving wiring of relays: Preparation & fixing of Bakelite hylum sheet 450x800x6mm and Bakelite shelf 450x450x25mm duly fixed by angle iron piece of different size inside all the app. Cases. Hylum board shall be fixed on an angle iron frame of 25mmx25mmx3mm. Angle iron frame will be fixed in location boxes secured by nuts and bolts. This includes fixing of fuses, ARA terminal, Q series relays and other type relays on square bars fixing and jamming of cables with 2-inch thick salwood plank provided at the bottom. This will include
through the salwood plank and all cable entry points on location boxes, location huts, JBs relay room/battery room to be closed with suitable masonry Works covered with sand and plastering. Wiring description for terminal drawing of circuits, inside app. Case. Painting from outside as well inside with red oxide and aluminum paint is covered separately. Size of lettering will be 100mm or as per instructions of Engineer at site. All materials including Bakelite shelf, hylum board, salwood plank, wire and wiring material, non-deteriorating type HRC fuses with bases, catenary wires, nuts and bolts and other items shall be supplied by the contractor and shall be as per the RDSO specn.(as applicable). Relays, ARA terminals only shall be supplied by the Railways.
Description:- Preparation of App. Case half not involving wiring of relays: Preparation & fixing of Bakelite hylum sheet 450x800x6mm and Bakelite shelf 450x450x25mm duly fixed by angle iron piece of different size inside all the app. Cases. Hylum board shall be fixed on an angle iron frame of 25mmx25mmx3mm. Angle iron frame will be fixed in location boxes secured by nuts and bolts. This includes fixing of fuses, ARA terminal, fixing and jamming of cables with 2-inch thick salwood plank provided at the bottom. This will include opening, pasting and jamming armour of each cable in the
location boxes, location huts, JBs relay room/battery room to be closed with suitable masonry Works covered with sand and plastering. Wiring description for terminal drawing of circuits, inside app. Case. Painting from outside as well inside with red oxide and aluminum paint is covered separately. Size of lettering will be 100mm or as per instructions of Engineer at site. All materials including Backelite shelf, hylum board, salwood plank, wire and wiring material, non-deteriorating type HRC fuses with bases, catenary wires, nuts and bolts and other items shall be supplied by the contractor and shall be as per the RDSO specn.(as applicable). ARA terminals only shall be supplied by the Railways.
75/2006 (Rev.2) & IRS drawing No. SA-23741A(Alt.4), SA-23745(Alt.5), SA-23746 & SA-23756(Alt.3). Inspection; RDSO.
Description:- Supply, Installation, testing and commissioning of Electrically Operated lifting barrier assembly as per RDSO Spec. No. RDSO/SPN/208/2012 (version 2.0) or latest consisting of 2 nos. of electrically operated lifting barriers, 2 pedestals, 8 band circuit controller with limit switches of Siemens, hand cranks, 2 electric motors, 110V AC, without centrifugal switch, 2 GI Boom in 4 sections of 8 feet each with 2 retroreflective stop boards, boom light boxes, MS counter weight, 2
motorized boom locking /unlocking assembly with electrical coil complete (1 no. each). b) Supply of level crossing gate control panel floor mounting type with switches and buttons sheet metal fabricated, (1 No). c) Supply of push button for operating the gate with 2 NO/NC contact, green color-close & Amber-open, Siemens or Kaypee or similar make (1 no.) Inspections RDSO for supply portion. d) Supply of solid-state electronic flasher 24V DC operated (1 no. each). e) Supply of dual tone warning bell with 20W horn & 15W amplifier (2 no. each). Inspection for (d) & (e): Consignee
Description:- Design and preparation of wiring diagram for Level-Xing MACLS on the basis of approved interlocking plan, typical circuit diagram and as per Railway practice and latest rules prescribed by the Railway and obtaining approval of the competent authority. Preparation of locking
authority. Drawing shall be supplied as per following: - (i) Supply of 6 copies of completion set of superior quality paper, laminated, properly bound in steel clip jaw file with cushioned cover. (ii) Software backup of complete set in the form of CDs. (iii) The complete set of tracings. (iv) Design through CAD. (v) Drawing in A3 & plans in bigger size (6 sets). DYCSTE-C-I-LKO-S AND T/NORTHERN RLY
Description:- Cleaning, scraping, painting and lettering of all newly installed and existing gears by
and marking of all the circuit particulars near terminal-on-terminal board/in apparatus case/Jn. boxes and fuse nos, relay and equipment nomenclatures as per approved terminal chart and provisions of SEM.
station/LC Gate as per RDSO spec RDSO/SPN/186/2004, Ver. 2 or latest (if applicable). This includes LEDs, acrylic sheet etc. Inspection: Consignee or site Incharge.
62 Description:- Installation and complete wiring of optg-cum indication panel for mid-section LC Gate.
IRS:S:61/2000 (Amend. No. 3) or latest. Inspection: RDSO.
Description:- Supply, installation and wiring complete KLCR and its box in location boxes, supply, installation, wiring of heavy-duty push-button AC immunized, LED indicator on MS sheet as per N.R.
telephones as per instructions of the site Engr. This includes all materials such as heavy-duty push button, LED indicator (10mm), MS sheet of 4.5mm thick, nuts and bolts, fixing materials for the magneto telephone, and wiring materials to be supplied by contractor. Inspection: RDSO for supply portion.
accessories for L/B gate. Inspection: Consignee for supply portion.
Description:- Casting, concreting and curing of foundation for main signal of size (1,041mm X
NR/S&T/CON./2.1/97 all material such as anchor bolts, cement, sand aggregate to be supplied by contractor.
specification No. IRS-S-6-81, Rev-3 or latest. Inspection: RITES.
Description:- Supply of non-metallic (FRP) color light signal housing multi-unit type for Railway signalling suitable for RE Area, 2-Aspect complete without lamps, lenses and signals transformers, as
no.RDSO/SPN/194/2006/Ver.1.0 or latest and FRP material as per RDSO No.RDSO/SPN/151/1997 or latest. All drawing should be as per latest. Material to be procured from RDSO approved firm only. Note: Signal shall be compatible to LED Lamp. Inspection: Consignee.
Description:- Fixing of CLS surface base, bolting on the foundation. Erection of CLS post with signal unit on the top or on an off-set bracket and fitting ladder and guard to the post at the top. Concreting ladder base and embedded into the ground with supporting bracket in the middle, blanking of the ladder for a distance of 1 foot between the height 6' 9" and 7' 9" from the rail level by MS angle and MS sheet 6mm thick wherever required. This includes provision of wooden (SAL) cross arm 1 mtr x 1 mtr for CLS unit prior to the commissioning, fixing of LED aspect, current
Elevation & distance of foundation from track shall be in accordance with schedule of dimension for Indian Railways and as per NR practice. All items for the above works except Signal unit, LED signal, Signal post, Base and Ladder shall be supplied by the contractor including but not limited to the following: i) "U" bolt for offset brackets, ii) Wooden cross arm 1 mtr. x 1 mtr., iii) MS angle and MS sheet for blanking of ladder, iv) Supply and fixing of signal number plate (Retro reflective) with complete fittings as per standard railway practice. v) Wire mesh guard, lock for unit if required, nuts, bolts etc., for the following: (a) Installation, erection, wiring of 2 aspect color light signals.
71 DYCSTE-C-I-LKO-S AND T/NORTHERN RLY 71 Description:- Supply of non-metallic (FRP) color light signal housing multi-unit type for Railway signalling suitable for RE Area, 3/4-Aspect complete without lamps, lenses and signals transformers, as per RDSO Drg. No. SA-23003 A/M (Adv), Alt-8 or latest and as per specification no.RDSO/SPN/194/2006/Ver.1.0 or latest and FRP material as per RDSO No.RDSO/SPN/151/1997 or latest. All drawing should be as per latest. Material to be procured from RDSO approved firm only. Note: Signal shall be compatible to LED Lamp. Inspection: Consignee. (3-Aspect:9No. & 4-Aspect: 5No.).
Description:- Fixing of CLS surface base, bolting on the foundation. Erection of CLS post with signal unit on the top or on an off-set bracket and fitting ladder and guard to the post at the top. Concreting ladder base and embedded into the ground with supporting bracket in the middle, blanking of the ladder for a distance of 1 foot between the height 6' 9" and 7' 9" from the rail level by MS angle and MS sheet 6mm thick wherever required. This includes provision of wooden (SAL) cross arm 1 mtr x 1 mtr for CLS unit prior to the commissioning, fixing of LED aspect, current
Elevation & distance of foundation from track shall be in accordance with schedule of dimension for Indian Railways and as per NR practice. All items for the above works except Signal unit, LED signal, Signal post, Base and Ladder shall be supplied by the contractor including but not limited to the following: i) "U" bolt for offset brackets, ii) Wooden cross arm 1 mtr. x 1 mtr., iii) MS angle and MS sheet for blanking of ladder, iv) Supply and fixing of signal number plate (Retro reflective) with complete fittings as per standard railway practice. v) Wire mesh guard, lock for unit if required, nuts, bolts etc., for the following: (a) Installation, erection, wiring of 3/4 aspect color light signal.
Description:- Supply, Installation, wiring, testing and commissioning of SPT (Half Duplex) at IBS Location and adjacent stations. Each set shall comprise one no. of signal post telephone SPT) master unit (Which shall be installed on IBS post) along with one no. of slave unit to be installed in SM's
charge, ACES make or similar. Note: The contractor shall ensure that there is no interference in communication between the master and slave unit owing to power hump due to RE Induction. Cable from IB signal unit to the cable termination Board in SM's Room/Relay Room will be provided by Railway. Inspection: Consignee for supply portion.
Description:- Fabrication, Supply and fixing of retroreflective P/G/C/IB markers with complete
sheet, MS angle. Nut and bolts, paint and painting materials will be supplied by the Contractor. The P and G markers shall be as per Drg. No.S 23456(Adv) & SA 23477(Adv) respectively.
Description:- Casting, concreting, curing of foundations of size (400mmx300mm) at surface and
Board/Passenger Warning Board as per drg. No. NR/S&T/CON/7.4/97 & provisions of SEM. It includes supply of retroreflective SLB/BSLB/SB/ calling on boards/Goods Warning Board/Passenger Warning Board. The SLB/BSLB shall be as per approved Drg. No.SA-2373 or latest.
Drg.No.11393. Inspection; Consignee/Site incharge.
acid with mounting stand in location boxes.
Little Fuse or similar. Inspection: Consignee for supply portion.
Description:- Supply of OFC integrated access device 1U height or 1.5 U height /19" rack mountable for LVCD /Digital axle counter purpose; optical module integrated in the unit supporting dual core OFC and one 100Mbps Ethernet port for surveillance/ smoke detector; optical distance
configurable) to support axle counter / UFSBI/Control phone/ EC/RTU/ and one TELNET/SNMP port; unit to support DC/AC power supply ; unit to support change over mechanism between quad and optical fiber for E&M option; one number cable to be provided along with unit for E&M ; FABIO/2CX/OFC/DC & Module 2W/4W four port : Make :TEAM ENGG/FABIO/WAVES or similar /TANSY. Inspection: RITES. 1069327.0
8 DYCSTE-C-I-LKO-S AND T/NORTHERN RLY
RDSO Spec. No. IRS-S-104/2012 ver.0 with latest amendments) Suitable to work on OFC/1 Quad Cable as 16 Input -16 Output Multiplexer for IB signalling including 68 Nos of QN1 (8F/8B) Relays for system commissioning. It also includes RS232 Fiber converter for operating UFSBI equipment as per IRS specn. No.IRS:S-104/2012 Ver.0 on dark fiber and Supply of prewired powder coated MS Cabinet at least 36U (1.6 m) approx. for housing UFSBI electronic modules, relay racks, SPD modules, 4 nos. of QN1 (8F/8B) relays per pair, etc. as required for commissioning of UFSBI electronics in Automatic Block signalling/IB signalling. Inspection: RDSO for supply portion.
Description:- Supply, installation and commissioning of Reliability improvement kit suitable to work with UFSBI Deltron make as per RDSO/SPN/104/2012 or latest. it comprises (a) Automatic Media Changeover or modems working on redundant channels for data transmission on
secondary media OFC/Quad-01 pair (c) Type C&D power line (VF 24 AC/DC: 02 Nos. V20C/3PH- 150VA: 02 Nos.) & Data line SPD (MDP 4D/5T: 02Nos.) comprising suitable to work with 01 pair UFSBI: 01 Set (d) Power monitor & soft start unit PMSS: 01pair. Make-DELTRON. (Warranty Period: Up to 30 months from the date of delivery). Inspection: RDSO for supply portion.
backup media compatible with IBS (direct single media 1 core optical fiber cable up to 30 km distance). Inspection: RDSO.
83 Description:- Supply of Reset Box RB 259A suitable for SSDAC. Inspection: RDSO.
Description:- Supply of portable Management Console for onsite programming. Model: DELL
RAM 8GB or higher, SSD 1TB, with inbuilt dual Graphic Card) or better as per specification. Inspection: Consignee
Description:- Supply, installation & commissioning of maintenance free earth suitable kit as per RDSO specification RDSO/SPN/197/2008 and Drg No. SDO/RDSO/E&B/002 dated 19.09.2008 or latest with latest amendments. Earthing kit consists of 1. Earthing electrode of 17mm dia and 3 meter long-01 no. 2. MEEB (300mmX25mmX6MM) -01 no. 3. SEEB (150mmX25mmX6mm)-01 no. 4. Earth enhancing compound-30 Kg (minimum). This includes provision of earth connection from MEEB to S&T equipment i.e. cable sheath, apparatus case, IPS, data logger, MSDAC, SSDAC etc. with PVC
Railways. Note: At certain locations it may not be possible to achieve earth resistance of less than 1.0 ohm with one earth electrode/pit due to soil resistivity. In such case provision of loop earth consisting of more than one earth pit shall be done. For inter-connection of two earth pits copper tape of size 25x2 sq. mm shall be provided by contractor. The number of pits required shall be decided based upon the resistance achieved for the earth pit already installed. The procedure mentioned above for one earth pit shall be repeated for other earth pits. The other earth so installed for the purpose of loop earthing arrangement shall be counted as separate earth. Inspection: RDSO for supply portion.
Description:- Supply and installation of earth electrodes as per std. practice. The item includes digging of pit in earth, 3 Mtrs. deep and fixing earth electrode pipe. Casting of cement concrete enclosures as per drg. No. (NR/S&T/CON/6.4/97). The soil treatment shall be done as per std. practice. The item includes provision of mild steel flat of size 35mm x 6mm (as per IRSEM) and nut
block instrument, cable sheath of power equipment, signal base, apparatus case, CT rack / relay racks, other equipment as per the instruction of Engr. at site & IRSEM. Earthing connection location to location shall be done through cable which shall be provided by Railway. Complete materials such as earth electrodes as per drg. No. (NR/S&T/CON/6.3/97), cement, wiring material, nut bolt for connection & mild steel flat of size 35mm x 6mm or 210 sqm as per SEM etc. to be supplied by the contractor. Inspection: RITES for supply portion. Vehicle-
Month Description:- Hiring and operating multi utility vehicle (Maximum 3 vehicle in a month) of loading capacity one MT with sitting capacity of 4 to 6 persons, 4-stroke, 4-cylinder engine, factory-built
fuel, lubricants, operating and maintenance including on kutcha/pucca road along the track. The contractor shall arrange road permit for vehicles for all the states of operation as per instructions of engineer incharge. Vehicle shall not be older than 3 years. The max KM utilization per month is 1200KM per vehicle.
88 DYCSTE-C-I-LKO-S AND T/NORTHERN RLY 88 Description:- Extra over item no.87 above for every additional KM or part thereof over 1200 KM per month.
fire alarm loop required as per UL listed solution & RDSO/SPN/217/2021 Ver 3.0 or latest. Spare cost also included & to be supplied as per RDSO para no.4.15. Inspection: RDSO for supply portion.
Description:- Supply, installation, testing and commissioning of single channel laser or high-power LED based Aspiration detection unit (for AC room) with area covering 5000 sq.ft. with programmable
discrimination of particle site, ultrasonic air flow sensing auto learn feature with TCP/IP network capability, the aspiration system shall also include external power supply unit with battery back-up. Approval-UL/LPCB/VDS listed and shall comply to specification No.RDSO/SPN/217/2021 ver-3 or latest. Spare cost also included & to be supplied as per RDSO para no.4.15. Inspection: RDSO for supply portion.
Description:- Supply, installation, commissioning Heat and Smoke Multi sensor detector with automatically adjusts sensitivity levels without the need for operator intervention or programming
type facility and address through switch. The base should also be supplied as per RDSO/SPN/217/2017 Ver 3.0 or latest. Spare cost also included & to be supplied as per RDSO para no.4.15. Inspection: RDSO for supply portion.
Description:- Supply, installation, commissioning of microprocessor based networkable analogue addressable UL listed and modular type of Fire alarm Control Panel with 2-loop expandable up to 4- loop with 80 character display with battery charger and battery, backup for 24 Hr. normal operation
the FAS panel and 1,000 event recording facility as per RDSO/SPN/217/2021, Ver 3.0 or latest with GSM module-01 no. for sending SMS to configured mobile number and relay module-02 no. for connecting to datalogger for remote monitoring. The panel should support sufficient devices of both detectors and modules in a single line. Spare cost also included & to be supplied as per RDSO para no.4.15. Inspection: RDSO for supply portion.
Description:- Supply, installation, testing and commissioning of UL/LPCB/VDS listed CPVC pipe with
to RDSO/SPN/217/2021 Ver.3.0 or latest. Spare costs are also included & to be supplied as per RDSO Para no.4.15. Inspection: RDSO for supply portion.
Description:- Supply, installation, commissioning of analogue type Linear Heat Sensing (LHS) cable
resettable temperature limit of 120 degree Celsius it shall have an activation temperature of 70 degree Celsius as per RDSO/SPN/217/2021, Ver 3.0 or latest. Spare cost also included & to be supplied as per RDSO para no.4.15. Inspection: RDSO for supply portion.
the control panel as per RDSO/SPN/217/2021, Ver 3.0 or latest. Spare cost also included & to be supplied as per RDSO para no.4.15. Inspection: RDSO for supply portion.
RDSO/SPN/217/2021 Ver. 3.0 or latest. Spare cost also included & to be supplied as per RDSO para no.4.15. Inspection: RDSO for supply portion.
RDSO/SPN/217/2021, Ver 3.0 or latest. Spare cost also included & to be supplied as per RDSO para no.4.15. Inspection: RDSO for supply portion.
RDSO/SPN/217/2021, Ver 3.0 or latest. Spare cost also included & to be supplied as per RDSO para no.4.15. Inspection: RDSO for supply portion.
as per RDSO/SPN/217/2021, Ver 3.0 or latest. Spare cost also included & to be supplied as per RDSO para no.4.15. Inspection: RDSO for supply portion.
DYCSTE-C-I-LKO-S AND T/NORTHERN RLY
RDSO/SPN/217/2021, Ver 3.0 or latest. Spare cost also included & to be supplied as per RDSO para no.4.15. Inspection: RDSO for supply portion.
Description:- Supply of ISI marked Carbon di Oxide type (BC) fire extinguisher of 4.5 Kg capacity
conforming to IS: 3224 high pressure meter long discharge hose and horn complete with initial gas charged with carrying handle and wall mounting braket etc. as required by site Engineer. Inspection: Consignee
Description:- Dismantling and releasing single signal post which includes dismantling of signal
signal posts etc. All dismantled material to be transported and stacked in the store of SSE/C/TKJ or DYCMM/SSB/LKO or any other stores of northern railway.
Description:- Dismantling and release of location boxes/apparatus case Jn boxes including of
therein complete with fittings all materials transported and deposited in the store of SSE/CTKJ or DYCMM/SSB/LKO or any other stores of northern railway.
Description:- Loading, leading and unloading of released/other materials from site to DyCMM/AMV
other Railway Material etc using Truck/MUV from Railway Store/any designated place to work site. Labour required for loading/unloading and transportation vehicle will be arranged by contractor.
Description:- Earth work for excavation and refilling around location boxes and signals etc. where
location to the center of filling and lift from main ground level. The earth work should be well rammed including breaking of clods, leveling and dressing etc. as per instruction of Engineer at site.
Description:- Concreting unscheduled items in concrete of 1:3:6 ratio in cement, coarse sand and aggregate 25mm at different places in the yard and plastering top in fine plaster of 1:4 cement sand
charge. The volume in cubic meters shall include the volume occupied by any CI foundation, trestle, MS angle or flat or GI pipe required to be embedded in the casting. Cement coarse sand and aggregate 25mm are to be supplied by the contractor.
Description:- Cleaning, scrapping, painting & lettering of all newly installed & existing gears such as signals, point equipment, track circuit equipment with TC No. on rail, apparatus cases, JB, TLJB, point Roding, cranks, compensators etc. including gate equipment if existing in station section as
painting materials to be supplied by the contractor. This includes writing, and painting requirement of all indoor and outdoor gears along with marking of all circuit Nos. near terminal and terminal boards/rack in apparatus cases, Jn. boxes, relay room, SMs room, writing of relay nomenclature, fuse Nos. and equipment nomenclature as per the approved plans and as per provision of IRSEM. (1 JOB = 1 Station).
This includes all the pipe connections from water source to unit and also to collection unit as per instruction of site engineer. Inspection: Consignee for supply portion.
leveling the formation, dismantling any infringing structures, clearing and removing debris etc., with all lead and lifts etc., complete and as per the instruction of railway representative at site.
Description:- Supply of ESM furniture of Godrej or similar make consisting of the following: 1. Executive revolving bearing series low back floating chair with normal arms cushioned Chair : 1No.
Visitor chair seat & back cushion with high density Foam with plastic PVC handle capsul type Flat pipe duly Painted black : 3Nos. 4. One Steel Almirah of size 48"x30"x17" with lock and handle arrangement for record keeping at station. Inspection: Consignee
latest amendments. Inspection: Consignee
DYCSTE-C-I-LKO-S AND T/NORTHERN RLY Description:- Supply and Installation of 20 pair DP box made of cast Aluminum within built locking system and waterproof should have double outlet with leading in brass nozzle. The main tag block plate is mounted on the inner aluminum chamber with brass terminal studded in back lite sheet. DP
This includes fixing of the same on 1" thick board of size as per directions of site engineer with ground nuts and bolts of suitable size and pipe fixed with clamps on pole /wall. All materials required for fixing & termination including salwood/hylum board and the hardware required for fixing will be supplied by contractor. Inspection: Consignee for supply portion.
Description:- Final location survey of cable route, preparation of cable route plan, terminating plan,
RDSO's code of practice "For installation and commissioning of OFC / 6 quad cable system" Approved drawings and documents shall be supplied in 6 hard copies in original of A4/A3 size along with 2 CD in AutoCAD of latest version.
Description:- Supply & provision of straight through joints thermo-shrink jointing kit with the help
and as per approved cable route plan at various locations for 06 Quad/04 Quad cable. Jointing kits to be supplied as per RDSO specification IRS:TC 77-2012 (Rev.-3) or latest amendments. Inspection: RDSO for supply portion.
Description:- Supply of thermo-shrink jointing kit as per IRS TC 77/2012 Rev.3 with Amendment 1
pump, houses, station cabins etc., using thermo-shrink jointing kit as per specifications, drawings and stipulations of tender documents. This includes all material required for making joints. Inspection: RDSO for supply portion.
22/76 with Amd-1 or latest amendments (round type). Inspection: Consignee
and indoor cable laying.
mm. (Inspection: Consignee).
Pair/0.6mm. (Inspection: Consignee).
pair/0.6 mm. (Inspection: Consignee).
materials, splicing, termination and testing of 2*24 fiber of the cable i.e. 48 fibers with all connectors material as per the instruction of the site engineer. (Inspection: RITES for supply portion).
Description:- Supply of cable fault locator for underground cable as per model no. Telscout TS-90
Frequency:150kHz (High Pass Filter), Gain:0 to 63dB), Stanlay or similar branded make as per specification.Inspection: RITES.
Inspection: Consignee
Description:- Laying of HDPE duct in the trenches, including in HDD/Manual Boring and supply
Engineer. It includes Supply of HDPE duct outer dia 40mm & inner dia 33mm as per TEC Gr No. G/CDS-08/02 Nov /2004 with latest amendment with end cap to be provided along with the drum at both ends. (RDSO specs No. RDSO/SPN/TC/45/2013 Rev.2.0). Inspection: RITES for supply portion.
125 Description:- End plug for item no.124 above. Inspection: Consignee for supply portion.
DYCSTE-C-I-LKO-S AND T/NORTHERN RLY
supply portion.
128 Description:- Blowing/Drawing of OFC cable in the HDPE duct by mechanical system.
Description:- Supply and installation of optical fiber cable joint enclosure as per TEC spec no.
testing). This includes provision of jointing kit (RCC/Prefabricated) as detailed in the technical specification and as advised by engineer at site. Inspection: Consignee for supply portion.
at both end as per IRS:TC-81/2000 with latest amendment. Inspection: Consignee
both end as per IRS:TC-81/2000 with latest amendment. Inspection: Consignee
132 Description:- Installation & commissioning of OFC equipment for SCADA/axle counter per location.
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
BDKN_SLNIBS_compressed1.pdf
ATTACHMENT
SLN-PKXIBS-Model2.pdf
ATTACHMENT
TenderNotice.pdf
ATTACHMENT
TenderDocument01-26.pdf
ATTACHMENT
RBL-GANG.pdf
ATTACHMENT
RBL-RUM.pdf
ATTACHMENT
MBDP-PHV.pdf
ATTACHMENT
Standard_General_Condition_060919.pdf GCC 2019
ATTACHMENT
Standard_General_Condition_060919.pdf
ATTACHMENT
Download all tender documents and submit your bid