ADDN / ALTN TO SPECTRUM BUILDING (P-43) UNDER AGE B/R-II AND CERTAIN WORKS UNDER GE HADDO

Amount

Excavation in trenches not exceeding 1.5 mtr wide and not exceeding 1.5 m in depth, for foundation etc., or for shafts, wells, cess pits, manholes, pier holes etc not exc. 10 Sqm on plan and n.exc. 1.5m in depth and getting out in soft/loose soil complete all as specified and as directed.

Excavation in trenches not exceeding 1.5 mtr wide and not exceeding 1.5 m in depth, for foundation etc., or for shafts, wells, cess pits, manholes, pier holes etc not exc. 10 Sqm on plan and depth exc 1.5m and n.exc. 3m and getting out in soft/loose soil complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm each as in soils complete all as specified and as directed.

Spreading, levelling in layers not exceeding 25cm thick as in floors using earth obtain from excavation, well rammed and watered complete all as specified.

Removing excavated material (soils) to a distance not exceeding 50 metres and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and as directed.

M&L for hardcore using broken stone or boulders of gauge exceeding 63 mm but not exceeding 100 mm, deposited, spread and levelled in layers not exceeding 15cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for anti termite treatment to the bottom and sides of excavation at the rate of 5 litres of emulsion per square metre of surface area

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for complete all as specified and as directed.

M&L for PCC (1:4:8) type D2 (using 40mm graded stone aggregate) as in foundation filling and mass concrete complete all as specified and as directed.

M&L for 75mm thick PCC (1:4:8) type D2 (using 40mm graded stone aggregate) as in sub base complete all as specified and as directed.

M&L for providing cement concrete 1:2:4 type B1 ( 20mm graded stone aggregate) for hold fast, copings, lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed

M&L for design mix reinforced cement concrete M-30 grade (using 20mm graded stone aggregate) as in foundations, including rafts, footings, foundation beams, plinth beams, bases for columns etc., basement slabs, under-reamed piles and mass concrete complete all as specified and as directed.

M&L for design mix reinforced cement concrete M-30 grade (using 20mm graded stone aggregate) as in columns, pillars, piers, posts and struts complete all as specified and as directed.

M&L for design mix reinforced cement concrete M-30 grade (using 20mm graded stone aggregate) as in beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and as directed.

M&L for design mix reinforced cement concrete M-30 grade (using 20mm graded stone aggregate) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs, cooking platforms and in shelves and the like complete all as specified and as directed.

M&L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

M&L for Mild steel TMT bars 6 to 8mm dia , cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

M&L for use and waste of formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work vertical or to batter for rough finished surfaces of concrete flat complete all as specified and as directed.

M&L for use and waste of formwork to sides of sides of pillars, posts, struts, piers, columns and stanchions for rough finished surfaces of concrete flat complete all as specified and as directed.

M&L for use and waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs etc., also splays between floors and beams etc., for rough finished surfaces of concrete flat complete all as specified and as directed.

M&L for use and waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work, not exceeding 200mm thick (Horizontal or sloping) for rough finished surfaces of concrete flat complete all as specified and as directed.

M&L for pre-cast cement concrete block masonry with solid blocks made up of (1:3:6) type C1 (using 20mm graded stone aggregate), masonry exceeding 10cm in width and setting in cement mortar (1:6) complete all as specified and directed.

M&L for rendering 5mm thick in CM (1:3) on fair faces of concrete surfaces of ceiling, surfaces finished smooth and even without using extra cement complete all as specified and as directed.

M&L for rendering 10mm thick in CM (1:6) on fair faces of brick work or concrete, surfaces finished fair and even complete all as specified and as directed.

M&L for preparation of newly plastered surfaces of walls of any description and applying two coats of cement based paint complete all as specified and as directed.

M&L for preparation of newly plastered surfaces of walls of any description and applying two coats of distemper oil emulsion over a coat of primer after levelling the undulations if any with cement putty complete all as specified and as directed.

M&L for preparation of newly plastered surfaces of ceiling of any description and applying two coats of distemper oil emulsion over a coat of primer after levelling the undulations if any with cement putty complete all as specified and as directed.

M&L for preparation of newly plastered surfaces of external walls of any description and applying two coats of weather proof antifungal (exterior grade) acrylic emulsion over a coat of primer from the same manufacturer complete all as specified and as directed.

M&L for preparation of old plastered surfaces of walls by complete removal of existing treatment by scraping, washing, cleaning etc., and applying two coats of distemper oil emulsion over a coat of primer including 3mm wall care putty after filling the cracks with filler complete all as specified and as directed.

M&L for preparation of new wooden surfaces of any description, not exceeding 10cm in width or girth and applying two coats of synthetic enamel paint of first quality over a coat of pink primer complete all as specified and as directed.

M&L for non-skid ceramic coloured tiles 7 to 8 mm thick (square/ rectangular), area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, as in floors etc, laid over and including 15mm thick screed bed in CM (1:4), set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed.

M&L for non-skid ceramic coloured tiles 7 to 8 mm thick (square/ rectangular), area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, as in floors etc, laid over and including 15mm thick screed bed in CM (1:4), set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed.

M&L for glazed ceramic designed coloured tiles in vertical surfaces using size of tiles 300x450x7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match with colour of tile with and including 10mm thick backing coat in CM (1:3), set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed.

M&L for 20mm thick granite slab (of approved shade), machine cut, as in floors, vertical surfaces, steps (treads/risers) and the like laid over cement mortar (1:4) and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding, polishing and rounding (chamfering) the edges complete all as specified and directed.

M&L for providing best quality 30mm thick 1st class hardwood boarding in flooring, 150mm wide planned one side and edges tongued and grooved or rebated over 40mm thick and 50mm wide plain 1st class teak wood filled frame work, spaced at 60cm c/c/ both ways with two coats of chemical treatment to all unexposed wooden surfaces before fixing and finally polishing the top surface with melanine polish complete all as specified

M&L for sand (river sand) filling under floors or in foundations including watering and consolidation complete all as specified and as directed.

M&L for French polishing on surfaces of any description, width or girth including cleaning and preparing the surface including a coat of wood filler on new works with two or more coats

M&L for mild steel plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment Fe-410-W (Gde-E-250) Quality 'A' complete all as specified and as directed.

M&L for mild steel roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (beam, tee, angle, channel or flat sections) including distance pieces, cleats etc., conforming to Fe-410-W (Gde E-250) Quality 'A' complete all as specified and as directed.

S&F mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, length of bolt not exceeding 5 cm and dia of neck 16 to 20 mm complete all as specified and as directed.

M&L for preparation of new steel and iron surfaces of any description, not otherwise described, over 10cm in width or girth and applying two coats of synthetic enamel paint of first quality over a coat of red oxide zinc chrome primer complete all as specified and as directed.

M&L for second class hard wood (Hollock) plain fillets, square, rectangular or triangular in section, clean sawn, secured with nails or brads of sectional area exceeding 13 Sqcm but not exceeding 25 Sqcm complete all as specified and as directed.

S&F wood wool building slabs, light weight, type 1, fixed with nails to timber framework of 40mm thickness complete all as specified and as directed by Engr-in-Charge

S&F wood wool building slabs, light weight, type 1, fixed with nails to timber framework of 25mm thickness complete all as specified and as directed by Engr-in-Charge

Supply only polyethene sheet, black of 150micron thickness complete all as specified and as directed

M&L for aluminium composite panel sheet of 3.0mm thick with skin thickness of 0.25mm of aluminium on both sides, sandwiched by 2.5mm polyethylene core with PVDF coating of 30.0 micron fixed over frame made up of aluminium hollow section of 25x50mm, 2.0mm thick, duly fixed to wall/ceiling with expansion fastener having panels not exceeding 1200x1200mm with necessary silicon filling, in approved pattern as in columns, beams, walls etc., complete all as specified and as directed. NOTE: Necessary scaffolding required for the work shall be deemed to include in the unit rate quoted.

Dismantling ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets complete all as specified and as directed.

M&L for anodised aluminium snap grid frame work for false ceiling with size of grid 605mm x 605mm all as specified in SSR Part-I 2009, hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of G.I. flat iron 40x3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long including cutting, drilling, jointing etc., 6mm thick non-asbestos fibre cement building design boards fixed or laid/ inserted to aluminium frame work with screws including two coats oil bound distemper complete all as specified and as directed.

S&F stainless steel three dimensional letters (Block, Roman, Italic or Indian) of size 450mm height, 50 to 70mm width and 30 to 50mm depth, made up of 1mm thick sheet with anchoring facility fixed to wall surfaces by necessary drilling/punching in walls and by using sealants/adhesives etc., complete all as specified and as directed.

S&F stainless steel three dimensional letters (Block, Roman, Italic or Indian) of size 150mm height, 50 width and 25mm depth, made up of 1mm thick sheet with anchoring facility fixed to wall surfaces by necessary drilling/punching in walls and by using sealants/adhesives etc., complete all as specified and as directed.

S&F pre-painted zinc coated aluminium sheet (Galvalume) GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed. NOTES: The self tapping screw shall be of adequate length to drive into complete thickness of purlin/rafter etc., and shall be fixed using neoprene and EPDM washers. Penetration and laps in sheet shall be sealed by using proper sealant profile. HDPE fillers shall be provided wherever required to close voids between sheets, sheet & fasteners etc., as per SSR Part-I 2009 complete.

S&F pre-painted zinc coated aluminium sheet (Galvalume) GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall/valley gutters, fixed with self tapping screws including scaffolding for a height upto 12.0 metres complete all as specified and as directed. NOTES: The self tapping screw shall be of adequate length to drive into complete thickness of purlin/rafter etc., and shall be fixed using neoprene and EPDM washers. Penetration and laps in sheet shall be sealed by using proper sealant profile. HDPE fillers shall be provided wherever required to close voids between sheets, sheet & fasteners etc., as per SSR Part-I 2009 complete.

S&F aluminium flat iron wind ties of any size and thickness fixed with self tapping screws for fixing roofing sheets complete all as specified and as directed. NOTES: The self tapping screw shall be of adequate length to drive into complete thickness of purlin/rafter etc., and shall be fixed using neoprene and EPDM washers.

S&F Aluminium tubular section of size 25mmx50mmx2mm thick, duly fixed to wall/ceiling with expansion fastener, having panels not exceeding 1200mm x 1200mm with necessary silicon film in approved pattern as in column, beam, wall etc, complete all as specified and as directed Note : Necessary scaffolding required for the work shall be deemed to include in the unit rate quoted.

M&L for powder coated anodised aluminium partition, window and door/ventilator with frame and shutters and grill fully or partly glazed, sliding/openable/fixed fully glazed and panels fixed with panels inserts 12 mm thick pre-laminated particle board/sheet glass including necessary jointing cleats, glazing clips, rubber beading, neoprene packing, anodised aluminium snap beading, screws, anodized aluminium fittings such as handles, aluminium butt hinges, aluminium tower bolts etc. The size of aluminium section shall be all as specified in relevant IS Code and SSR Part-I complete all as specified and as directed. NOTES: (i) Supply only floor spring, glass, Imax hinges, SS friction hinges, particle board, aluminium fly proof mesh will be measured and paid separately under relevant items of this BOQ. (ii) Weight of aluminium section only shall be accounted for the purpose of payment. However unit rate quoted shall be deemed to include for cost of rubber beading, neoprene packing, fittings such as handles, butt hinges, tower bolts, rollers for sliding windows, locking arrangement and fixing only of panel inserts of glass/ particle board/aluminium fly proof mesh etc. (iii) Weight of aluminium handle, butt hinges, tower bolts shall not be accounted for payment purpose.

SUPPLY ONLY 5.5 mm thick sheet glass, ordinary quality and glazing with aluminium glazing clips in square not exceeding 0.5 Sqm in each pane complete all as specified and as directed.

SUPPLY ONLY 4.0 mm thick sheet glass, ordinary quality and glazing with aluminium glazing clips in square not exceeding 0.5 Sqm in each pane complete all as specified and as directed.

SUPPLY ONLY 4.0 mm thick figured glass, pin headed ordinary quality and glazing with aluminium glazing clips in square not exceeding 0.5 Sqm in each pane complete all as specified and as directed.

S&F Solar control film 25 micron reflective type (Garware sun control or equivalent) complete all as specified and as directed.

Supply and fix 9mm thick prelaminated particle board, interior grade, prelaminated both side with decorative choice lamination fixed with screws to timber framework or wall complete all as specified and as directed.

Supply only aluminium expanded metal fly proof mesh, cut to required size and shape, with 0.45mm nominal dia of wire and average width of aperture 1.40mm complete all as specified and as directed.

S&F anodised aluminium grill of approved pattern, anodised powder coated, cut to required size and shape, fixed in position with aluminium beading & frame made of aluminium F-section fixed to aluminium windows/ventilators complete all as specified and as directed.

S&F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. square tube as per specification & drawing, fixed in opening complete all as specified and as directed.

S&F factory made solid PVC moulded door shutter with particle board core, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick moulded prelaminated PVC sheet on the front face & 2mm plain colour PVC sheet on back face as per specification & drawing fixed to door frame complete all as specified and as directed.

S&F 100mm size butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised, type B-21 complete all as specified and as directed.

S&F 75mm size extruded aluminium alloy handles, fabricated type, anodised complete all as specified and as directed.

S&F 100mm long aluminium anodised, barrel tower bolts of extruded section complete all as specified and as directed.

S&F sliding door bolt, 300mm long, aluminium alloy, anodised, with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy complete all as specified and as directed.

S&F 110mm bore PVC (SWR) pipes single socketed, in any length pipes single socketed, in any length with rubber ring joints, laid in trenches/fixed to walls/placed in weep holes using synthetic rubber adhesive cement solvent complete all as specified and as directed.

S&F 75mm bore PVC (SWR) pipes single socketed, in any length pipes single socketed, in any length with rubber ring joints, laid in trenches/fixed to walls/placed in weep holes using synthetic rubber adhesive cement solvent complete all as specified and as directed.

S&F PVC (SWR) bends any radius, diameter of outlet 110 mm complete all as specified and as directed.

S&F PVC (SWR) bends any radius, diameter of outlet 75 mm complete all as specified and as directed.

S&F PVC (SWR) branch piece, Double (Double T) equal or unequal, diameter of outlet 110 mm complete all as specified and as directed.

S&F PVC (SWR) branch piece, Double (Double T) equal or unequal, diameter of outlet 75 mm complete all as specified and as directed.

S&F PVC (SWR) vent cowl of diameter 110 mm complete all as specified and as directed.

S&F PVC (SWR) multi floor trap with grating including jointing with solvent cement, diameter of outlet 75 mm complete all as specified and as directed.

M&L for vitreous China wash hand basin, white, flat back, size 550mm x 400mm including cutting for and pinning in ends of brackets or erecting stand, 32mm dia waste coupling brass chromium plated, bottle trap 32mm bore brass chromium plated with necessary packing union and caps, chain and plug, PVC connections 15mm size with PTMT nuts of length 450mm, screwed down for iron pipe or for unions complete all as specified and as directed.

M&L for vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests, P or S trap including provision of lime concrete bedding with and including flush pipe of polyethylene of low or high density or PVC 32 mm dia, PVC connections 15mm size with PTMT nuts of length 450mm complete all as specified and as directed.

M&L for PVC valveless, syphonic action type, flushing cistern, 10 litre capacity, low level, white, with inlet, ball valve, float and handle including brackets complete all as specified and as directed.

S&F pillar tap, brass, 15mm dia, chromium plated, fancy type with capstan heads, screwed down, high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe complete all as specified and as directed. MAKE: PRAYAG Cat part No. PIS-02H or equivalent in PARRYWARE/ZOLOTO/JOHNSON

S&F bib tap, brass, 15mm dia, chromium plated, fancy type, with crutch or butterfly handle, screwed down, screwed for iron pipe or brass ferrule complete all as specified and as directed. MAKE: PRAYAG Cat part No. PIS-08H or equivalent in PARRYWARE/ ZOLOTO/ JOHNSON

S&F angular stop cock, 15mm dia, cast copper alloy, chromium plated, fancy type, with crutch or butterfly handle, with long shank and cup (concealed type) screwed down, screwed both ends for iron pipe or for unions complete all as specified and as directed. MAKE: PRAYAG Cat part No. PIS-10H or equivalent in PARRYWARE/ ZOLOTO/ JOHNSON

S&F tubular towel rail, 60 cm long, PTMT fixed with and including chromium plated brass screws, complete all as specified and as directed.

M&L for PVC connections 15mm size with PTMT nuts of length 600mm, complete all as specified and as directed.

M&L for Cutting chases in PCC block masonry walls, for shelves, lintels, edges of landing etc., and making good, cutting not exceeding 10 cm girth complete all as specified and directed.

S&F 20mm bore unplasticised PVC pipes of pressure rating 10 Kgf/cm² including fittings, fixed complete to walls, ceilings or in floors etc., (including concealing, if required) and to any type of pipe complete all as specified and as directed.

S&F 25mm bore unplasticised PVC pipes of pressure rating 10 Kgf/cm² including fittings, fixed complete to walls, ceilings or in floors etc., (including concealing, if required) and to any type of pipe complete all as specified and as directed.

S&F 25mm dia gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron or CPVC pipe, complete all as specified and as directed.

Cutting into existing manholes for connecting new drains for 150mm bore of pipe, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished, and reforming benching as required complete all as specified and as directed.

M&L for Point wiring complete with 1.5 Sqmm (nominal area) single core, PVC insulated unsheathed, FRLS cable, 1100 volts grade, multistranded copper conductor, drawn through and including rigid non metallic PVC conduit of suitable size (not less than 20mm dia) medium grade and conduit accessories concealed in walls/ceilings etc., including provision of PVC insulated 1.5 Sqmm FRLS cable with copper conductor green in colour for earth continuity and connected to common earth dolly and sunk in modular type pressed steel terminal boxes of suitable modules made out of 1.6mm thick MS sheet duly painted with two coats of anti-corrosive paint all over and modular cover plates with frames on top for suitable modules on top for housing switches, sockets etc., all as specified and as directed for ONE LIGHT/FAN point controlled by one, one way 6 Amps modular switch.

M&L for Point wiring complete with 1.5 Sqmm (nominal area) single core, PVC insulated unsheathed, FRLS cable, 1100 volts grade, multistranded copper conductor (with colour coding of Red/Blue/Yellow for phase and Black for neutral), drawn through and including rigid non metallic PVC casing and capping of suitable size (not less than 25mm) and accessories fixed on walls/ceilings etc., including provision of PVC insulated 1.5 Sqmm FRLS cable with copper conductor green in colour for earth continuity and connected to common earth dolly and sunk in CI boxes/pressed steel terminal boxes 60mm deep made out of 1.6mm thick MS sheet duly painted with two coats of anti-corrosive paint outside and with two coats of aluminium paint inside and laminated sheet cover of 3mm thick on top for housing the switches, socket outlet etc, all as specified and as directed for ONE 6A SOCKET OUTLET point controlled by one, one way 6 Amps switch on independent board.

S&F switch piano, flush type, single pole, one way, 6 Amps, 240 volts complete all as specified and as directed.

S&F switch socket outlet, 5 pin, 6A, flush type, multipurpose, 240 volts complete all as specified and as directed.

M&L for ceiling rose, three terminal, 65x20mm size, PVC/Polycarbonate, insulated body, 6A, 240 volts complete all as specified and as directed.

M&L for Sub main wiring complete with two runs (1P+1N) of 4.0 Sqmm single core, PVC insulated unsheathed, FRLS cable, 1100 volts grade, multistranded copper conductor (with colour coding of Red/Blue/Yellow for phase and Black for neutral) and one run of 4.0 Sqmm single core, PVC insulated unsheathed, FRLS cable, 1100 volts grade, multistranded copper conductor as earth wire green in colour including lugs, drawn through and including 32mm wide rigid non-metallic PVC casing and capping and its accessories (OR) 25mm dia PVC conduit and conduit accessories fixed on surface of wall/ceiling/roof/ floor complete all as specified and as directed. NOTE: Two runs of 4.0 Sqm copper conductor, One run of 4.0 Sqmm copper conductor as earth wire and one run of PVC casing and capping / PVC conduit shall be measured as one unit length.

S&F Tube light fittings LED 20 watts 4 feet including all accessories and fixing arrangements complete all as specified and directed Make :Philips Cat Part No :BN308C LED20S-6500 L60 PSU WH /C&S/Havells/ CG

S&F 18 watts recess mounting LED fitting including all accessories and fixing arrangements complete all as specified and directed. Make : Philips Model No Astra Max Metal panel/ CG /Havells/ C&S

S&F SPN DB sheet metal enclosure double door suitable (IP-43) Protection, 4 Way with 200 Amp rated standard bus bar of suitable size plate and common neutral link all enclosed in standard steel sheet flush mounting type factory fabricated complete. Make : Havells/L&T/Indo Asian/Legrand/Schneider

S&F MCB, SPN, "C" series, 240 volts, 32 Amps, 10 KA rupturing capacity complete all as specified and as directed. Make : Havells/L&T/Indo Asian/Legrand/Schneider

S&F MCB, SP, "C" series, 240 volts, 6-32 Amps, 10 KA rupturing capacity complete all as specified and as directed. Make : Havells/L&T/Indo Asian/Legrand/Schneider

kakolil trade agencies

Sree Tirumala Enterprises