Loading…
Loading…
Tender Value
₹45 L
EMD Value
₹90,000
Closing Date
6 Jul 2026, 6:00 pm
Similar tender results from the same govt authority in the past 3 years.
Shri. Shirish Sharma IDSE SE SAG
CWE AF KALAIKUNDA
REPAIR TO JOINT FILLING AND OTHER CONNECTED WKS AT MAIN TAXI TRACK, ORP AND CERTAIN OTHER AIR CRAFT MOVEMENT AREA AT AF STN KALAIKUNDA
2026_MES_772328_1
8776/KKD(P)/E8
Open Tender
Civil Works
150 days
CWE AF KALAIKUNDA
Please refer Tender documents.
8 documents required · 8 mandatory
₹500
GE (P) AF KALAIKUNDA
₹90,000
Yes
15 Jun 2026
15 Jun 2026
7 Jul 2026
15 Jun 2026
6 Jul 2026
29 Jun 2026
| Sl No | Description | Qty | Unit | Est. Rate | Est. Amount | Item Code |
|---|---|---|---|---|---|---|
| 1 | M & L for racking out of old existing joint sealant compound (Any type and any sealant compound) and back up rod of the existing joints by special tools like cutting blades/machines, widening of joints by 2 mm by using joint cutting blades of appropriate size, straight and smooth edges, joint cleaned thoroughly with application of compressed air, joint shall be made dry, vacuum cleaned and free of dirt, oil, vegetation and other debris. Application of two coats of primer with thin brush by forward and backward movement at an interval of 30 minutes before pacing the backup rod and pouring the sealant, thereafter filled with closed cell, medium density, cross linked polyethylene foam backup rod of suitable size for complete length of the joint for the joint width 6 to 10 mm, over it to be finally filled with polyurethane joint sealant meeting the requirements mentioned in BS-5212, BS-4254 and EN-141875-2003 with minimum movement accommodation factor MAF of +/- 30% complete all as specified and directed.
Note: - (i) Minimum depth of sealant will be as per respective manufacturers instruction. Sealant and primer will be of same make.
(ii) Masking tape will be used to avoid accidental seepage/spreading of sealant.
(iii) Bidders attention is invited to the depth of pavement joint required to be cut,in case of extra cutting biderrs needs to make good with suitable filler as directed by Engr-In-Charge/Manufacturer at his own cost.
(iv) Filling of joints to be done 2 to3 mm recessed during summer and in winter it should be filled up to top up.
(v) Fly wheel,spatula,triangular pallet Knife etc. to be used to maintain the recess and to give aesthetics. | 20 | 10RM | - | - | itemH1Code1 |
| 2 | All as per item No 1.00 here-in-before but, size of joint is 11 to 15 mm wide complete all as specified and as directed. | 147 | 10RM | - | - | itemH1Code2 |
| 3 | All as per item No 1.00 here-in-before but, size of joint is 16 to 20 mm wide complete all as specified and as directed. | 214 | 10RM | - | - | itemH1Code3 |
| 4 | M & L for racking out of old existing joint sealant compound (Any type and any sealant compound) and back up rod of the existing joints by special tools like cutting blades/machines, widening of joints by 2 mm by using joint cutting blades of appropriate size, straight and smooth edges, joint cleaned thoroughly with application of compressed air, joint shall be made dry, vacuum cleaned and free of dirt, oil, vegetation and other debris. Application of two coats of primer with thin brush by forward and backward movement at an interval of 30 minutes before pacing the backup rod and pouring the sealant, thereafter filled with pre-moulded 25mm thick Compressible polyethylene closed cell type filler board as specified , over it filled with , medium density, cross linked polyethylene foam backup rod of suitable size for complete length of the joint for the joint width 21 to 25 mm, over it to be finally filled with polyurethane joint sealant meeting the requirements mentioned in BS-5212, BS-4254 and EN-141875-2003 with minimum movement accommodation factor MAF of +/- 30% complete all as specified and directed.
Note: - (i) Minimum depth of sealant will be as per respective manufacturers instruction. Sealant and primer will be of same make.
(ii) Masking tape will be used to avoid accidental seepage/spreading of sealant.
(iii) Bidders attention is invited to the depth of pavement joint required to be cut,in case of extra cutting biderrs needs to make good with suitable filler as directed by Engr-In-Charge/Manufacturer at his own cost.
(iv) Filling of joints to be done 2 to3 mm recessed during summer and in winter it should be filled up to top up.
(v) Fly wheel,spatula,triangular pallet Knife etc. to be used to maintain the recess and to give aesthetics. | 588 | 10RM | - | - | itemH1Code4 |
| 5 | All as per item No 4.00 here-in-before but, size of joint is 26 to 30 mm wide complete all as specified and as directed. | 450 | 10RM | - | - | itemH1Code5 |
| 6 | Repair to broken spalled edges of joints pot holes etc of existing concrete slab by forming square/rectangular grooves with diamond/Machine cutter wider towards bottom to from key with the existing quality concrete cleaning / dusting the grooves using compressed air to remove all dust and dirt by air blower and repairing with Epoxy mortar after applying epoxy primer and applying one coat of Epoxy resin (Base & hardner, Ratio 2:1) over epoxy mortor, finished complete all as manufacturer's instructions and as directed . | 200 | 1000 Cu CM | - | - | itemH1Code6 |
| 7 | Supply only Shali Seal PU GG / SRIJAN RUNFILL Utility Pouch | 150 | KG | - | - | itemH1Code7 |
| 8 | Supply onlyBituminous Tape (100 mm wide x 10 m long) Sika MultiSeal / SRIJAN SUREBOND | 30 | Each | - | - | itemH1Code8 |
| 9 | Supply only Modified Streaming Asphalt Crack Stuffer SRIJAN ASPHA-FLO or Equivalent of Make STP, Choksey | 40 | Litre | - | - | itemH1Code9 |
| 10 | Supply only Streaming Concrete Crack, Joint, Pot Hole Stuffer for Concrete Runway / Helipad Surfaces or Equivalent of Make STP, Choksey | 40 | Litre | - | - | itemH1Code10 |
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Tendernotice_1.pdf
PDF • 0.24 MB
TENDERDOCUMENTS.pdf
Tender Documents • 0.58 MB
BOQ_864828.xls
BOQ • 2.02 MB
Download all tender documents and submit your bid