SPECIAL REPAIR TO BUILDING No. P-865/7 TO 865/12 AT SS COLONY AND PROVISION OF TOILET, BATHROOM AND ALLIED INFRA FOR 3 COY, CESR AT BB CANTT, SRINAGAR

Amount

Taking down chowkats or frames n exc 1.5 sqm each (without taking off shutters from the frames) complete, all as specified and as directed.

Taking down chowkats or frames exc 1.5 sqm but n. exc 4.00 Sqm each (without taking off shutters from the frames) complete, all as specified and as directed.

Taking down shutters of any description n exc 1 sqm each complete, all as specified and as directed.

S&F 2nd class hard wood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, complete, all as specified and as directed.

S&F to chowkats 35 mm thick 2nd class hard wood plain framed panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board with commercial face veneers complete all as specified and directed.

S&F to chowkats 35 mm thick 2nd class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass, etc sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and as directed.

S&F galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples complete, all as specified and as directed.

S&F 18/19 mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete all as specified and as directed.

S&F solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, suppling & fixing in opening as per specification & drawing complete all as specfied and as directed.

S&F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing complete all as specfied and as directed.

S&F butt hinges, medium weight cold rolled, mild steel of size 100 mm complete, all as specified and as directed.

S&F 150 mm long aluminium barrel tower bolts of extruded section complete, all as specified and as directed.

S&F 150 mm extruded aluminum alloy handles, fabricated type, anodised complete, all as specified and as directed.

S&F aluminium alloy, anodised, sliding door bolt 300 mm with hasp, staple (bolt type) and fixin glips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and as directed.

S&F mild steel, 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and as directed.

S&F 140mm (overall length of cover plate) floor door stopper of aluminium alloy body and tounge, anodised, with hard drawn steel spring, fixed in floor complete as all as specified and directed.

S&F aluminium powder coated (powder coating of required colour) three track sliding windows frame top & sides of size 92 x 31.75 x 1.50mm (Section No 20831), bottom of size 92 x 31.75 x 1.50mm (Section No 20832) and shutter top & bottom of size 40 x 18 x 1.55mm (Section No 20736) and side (handle) of size 40 x 18 x 1.55mm (Section No 20738) and lock side shutter frame of size 40 x 18 x 1.45mm (Section No 20737) and for wire guage shutter of size 18 x 43.50 x 1.35mm (Section No.20791) with locking arrangement including stainless steel wire mesh 0.36 mm nominal dia of wire with 1.40mm average aperture and fixed with stainless steel wire staples and providing 5.5mm thick tinted glass with necessary rubber beading gasket and aluminium (anodised) grill, square, ractangular or similar section, fixed with channel of size 38 x 12 x 13mm etc including making good to the disturbed surfaces complete as all as directed.

S&F aluminium (powder coated with approved colour) ventilator, partialy glazed and partialy louvers, outer frame & mullion fabricated with aluminium section of size 82.50 mm x 38.00 mm x 1.70 mm thick (Cat No 20036), half portion glazed with 4 mm thick frosted glass including rubber beading, & glazing clip, half portaion louvers of 80 mm wide & 4 mm thick frosted glass including aluminium louver patti including S.S wire gauge of fixing of 0.36mm dia and 1.40 width of aparture with 25x3mm think aluminium strip with screw to upper half portion of ventilator all fitting & fixture and fixed in position and aluminium (anodised) grill, square, ractangular or similar section, fixed with channel of size 38 x 12 x 13mm etc complete all as directed.

S&F in repair/replacement curtain rod 20 mm dia, mild steel, chromium plated, fancy type with fixing brackets and knobs at both ends as per site requirement complete all as specified and directed. Note:- The cost of brackets and knobs shall deemed to be included in the quoted rate. Nothing extra shall be paid on this account.

Taking down cement or cement lime plaster, any description on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc. complete all as specified and directed.

M&L for 10mm thick rendering on fair faces of brick work or concrete surfaces in cement mortar 1:6, finished even and smooth without uing extra cement complete all as specified and directed.

M&L for 10mm thick rendering on fair faces of brick work or concrete surfaces in cement mortar 1:4, finished even and smooth without uing extra cement complete all as specified and directed.

M&L for 5mm thick rendering on fair faces of brick work or concrete ceiling surfaces in cement mortar 1:3, finished even and smooth without uing extra cement complete all as specified and directed.

M&L for preparation of newly plastered/ unplastered walls surfaces and applying two coats of oil bound distemper over a coat of wall care putty complete as specified and directed.

M&L for preparation of newly plastered/ unplastered walls surfaces and applying two coats of cement base paint complete as specified and directed.

M&L for preparation of newly plastered/ unplastered ceiling surfaces and applying two coats of oil bound distemper over a coat of wall care putty complete as specified and directed.

M&L for preparation of old plastered/ unplastered walls surfaces and applying two coats of oil bound distemper complete as specified and directed.

M&L for preparation of old plastered/ unplastered walls surfaces and applying two coats of cement base paint complete as specified and directed.

Dismantling boarding, any description, fixed in any position with nails complete all as specified and directed.

S&F 20mm thick softwood second class boarding, with nails in any situation (except flooring and skirting) clean sawn with butt joints complete all as specified and as directed.

S&F 12mm prelaminated particle board, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete all as specified and as directed.

S&F 18mm prelaminated particle board, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete all as specified and as directed.

S&F butt hinges, medium weight cold rolled, mild steel of size 50 mm complete, all as specified and as directed.

S&F 40mm dia, cupboard knobs fixed with nut, screw and washer of brass, polished complete, all as specified and as directed.

S&F Ball catcher with 8mm dia steel ball and brass body and striking plate including letting in and fixed complete, all as specified and as directed.

Dismantling timber scantling 40 sqcm and over in section in any position as in unframed/framed work complete, all as specified and as directed

M&L for 2nd class soft wood as in scantling clean sawn, complete, all as specified and as directed.

Dismantling of wall and ceiling boards (fiber pulp, insulation, etc.) or insulation boards/slabs, any thickness, including cover fillets complete, all as specified and as directed.

S&F 2nd class softwood wrought plain fillets square, rectangular or triangular in section, clean sawn, secured with nails or brads sectional area exc 13 sqcm and n.exc 25 sqcm fixed with nails etc complete, all as specified and as directed.

S&F 2nd class softwood plain fillets square, rectangular or triangular in section, clean sawn, secured with nails or brads sectional area exc 6 sqcm and n.exc 13 sqcm fixed with nails etc complete, all as specified and as directed.

S&F 6mm thick plywood, grade BWR, type BB with nails to timber frame work as in ceiling (flat or sloping) complete, all as specified and as directed.

M&L for 6mm thick Veneered decorative plywood, grade 1 (with BWR resin) with decorative face veneers on one faces, fixed with nails to timber frame work complete, all as specified and as directed.

M&L for preparation of new wood and wood based surfaces of any description exc 10cm with or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed.

Dismantling plain or corrugated steel sheeting, any gauge thickness including nainital or similar pattern roof coverings complete, all as specified and as directed.

S&F 0.63mm thick galvanised, corrugated mild steel sheeting with two corrugations side lap, fixed with coach screws and washers, in roofs, walls etc. with grade of zinc coating 275 complete, all as specified and as directed.

Fixing only 0.63mm thick galvanised, corrugated mild steel sheeting with two corrugations side lap, fixed with coach screws and washers, in roofs, walls etc. with grade of zinc coating 275 retrieved from BOQ item No. 45 above complete, all as specified and as directed.

S&F 0.80 mm thick plain, galvanised, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275 with coach screws and washers complete all as specified and as directed.

M&L for preparation of new steel and iron surfaces of any description over 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed.

Demolition of cement concrete (unreinforced) in ground floor and paving n.exe 15 cm thickness (below or above ground level) complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified and as directed.

M&L for 40mm thick cement concrete (1:2:4) type B 1 (using 20 mm graded crushed stone aggregate) as in floors complete all as specified and as directed.

M&L for 75mm thick cement concrete (1:2:4) type B 2 (using 40 mm graded crushed stone aggregate) as in sub bases of floors and pavings complete all as specified and as directed.

M&L for Virified Ceramic light shade tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match shade of tile over and including 15mm thick screed bed in cement mortar 1:6, complete all as specified and directed.

M&L for Vitrified Ceramic light shade tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in skirting/dado/vertical surfaces etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match shade of tile over and including 10mm thick backing coat in cement mortar 1:3 complete all as specified and directed.

M&L for Non - skid Ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles over and including 15mm thick screed bed in cement mortar 1:6, complete all as specified and directed.

M&L for Glazed Ceramic coloured tiles in vertical surface 350x 250x 7 mm/ 450X350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match shade of tile over and including 10mm thick backing coat in cement mortar 1:3 complete all as specified and directed.

M&L for 75 mm thick, plain cement concrete (1:3:6), type C-2 (using 40mm graded crushed stone aggregate) as in plinth protection / hard standing etc, finishing cement concrete surface even and smooth without using extra cement including making joints with bitumastic filing in proportion of bitumen and sand 1:2 complete as specified and directed.

M&L for chequered cement concrete tiles 30cm x 30cm x 25mm thich set, joined and pointed in neat cement slurry in floors with grey cement and pigment and over and including 15mm thick screed bed in cement mortar 1:6, complete all as specified and directed.

Dismantling Stone slabs and tiles of any description or thickness in floors/walls, aprons etc. etc laid bedded and pointed in any mortar complete all as specified and directed.

M&L for Granite (of any type) work, 20 mm thick, (table rubbed and polished) in steps jambs, pillars, window cills, cooking platforms, and the like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over and including 20mm thick screed bed in cement mortar 1:3, complete all as specified and directed. complete all as specified and directed.

Taking up or down steel tubing 15 mm dia and connections and stacking neatly for offering credit complete all as specified and directed.

S&F Tubes, medium grade galvanised, 15 mm bore with all fittings and fixed to walls and ceilings or laid in floors complete all as specified and directed.

Taking up or down steel tubing 20 mm dia and connections and stacking neatly for offering credit complete all as specified and directed.

S&F Tubes, medium grade galvanised, 20 mm bore with all fittings and fixed to walls, ceilings and trenches or laid in floors complete all as specified and directed.

M&L for lagging to pipes of internal dia 15 mm used in internal water supply or plumbing all round with, 25 mm thick bonded mineral wool preformed 'SNAPON' pipe sections of density 144 Kg/cum conforming to IS-9842 with 0.01 mm thick aluminium foil complete all as specified and directed.

M&L for lagging to pipes of internal dia 20 mm used in internal water supply or plumbing all round with, 25 mm thick bonded mineral wool preformed 'SNAPON' pipe sections of density 144 Kg/cum conforming to IS-9842 with 0.01 mm thick aluminium foil complete all as specified and directed.

S&F in repair, plate rack of overall size 24 x 24 x 10 inch made out of 0.63mm thick stainless steel sheet complete all as specified and directed.

S&F in repair kitchen sinks with drainage board made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and directed.

S&F in repair Corner glass shelf of size 300mm with chromimum plated railing and brass brackets and screws complete all as specified and directed.

S&F in repair glass shelf 500x60mm with chromimum plated railing and brass brackets and screws complete all as specified and directed.

S&F in repair Brass CP wall mixture 2-in-1 for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and directed.

S&F in repairs brass chromium plated tubular towel rail, 20mm dia, D type, 60 cm long between flanges complete all as specified and directed.

S&F in repairs CP brass shower rose with swival joints complete fancy type for 15mm bore pipe complete all as specified and directed.

S&F in repair 15 mm dia bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe of size 15 mm dia and confirming to IS-781-1977, complete all as specified and directed.

S&F in repairs 15 mm bore, Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and directed.

S&F in repair wash hand basin vitreous china size 550x400mm white flat back including CP pillar tap heavy duty as approved by GE, waste, chain plug, pvc connection, pvc waste pipe complete all as specified and directed.

S&F in repair CP Mixer single lever basin mixer fancy type for WHB / Sink with double action for hot/Cold water complete all as specified and as directed.

S&F in repair CP Towel Ring fixed with and including Chromium plated brass screws complete all as specified and directed.

S&F in repair Vitreous china wash down water closet white orissa pattern of size 550x440mm including integral foot rest excluding flushing cistern and flush pipe) incl P or S trap complete all as specified and directed.

S&F in repairs 10 ltr capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets complete all as specified and directed.

S&F in repair PVC connections 15mm size with PTMT nuts of length 450mm complete all as specified and directed.

S&F in repair 75mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc. including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and directed.

S&F 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

S&F 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

S&F 110mm bore PVC (SWR) bends any radius complete all as specified and directed.

S&F 75mm bore PVC (SWR) bends any radius complete all as specified and directed.

Taking out UNSV storage water tank of capacity 1000 Ltrs complete all as specified and directed.

S&F rotational moulded polyethylene water storage tank (cylindrical, vertical with closed top) triple layered hoisted and fixed in position incl all accessories of capacity 1000 ltrs, incl S&F ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe of size 20 mm dia complete all as specified and directed.

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in any type of soil complete all as specified and directed.

Excavation in trenches, n exc 1.5 m wide and n exc 1.5 m in depth, for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, laying of pipe / cable etc. n exc 10 sqm on plan and n exc 1.5 m in depth and getting out in any type of soil complete all as specified and directed.

M&L for cement concrete (1:4:8) type D-2 (using 40mm graded crushed stone aggregate) as in foundations, filling and mass concrete complete all as specified and directed.

M&L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for mild steel TMT bars 5mm dia and over upto and including 10mm dia as in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for reinforced cement concrete (nominal mix) (1:2:4) type B1 (using 20mm graded crushed stone aggregate) as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc. basement slabs, under-reamed piles and mass concrete complete all as specified and directed.

M&L for reinforced cement concrete (nominal mix) (1:2:4) type B1 (using 20mm graded crushed stone aggregate) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

M&L for reinforced cement concrete (nominal mix) (1:2:4) type B1 (using 20mm graded crushed stone aggregate) as in columns pillers, piers, posts and struts complete all as specified and directed.

Use and waste of form work to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter for flat rough finished surfaces of concrete complete all as specified and directed.

Use and waste of form work to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) for flat rough finished surfaces of concrete complete all as specified and directed.

Use and waste of form work to sides of pillars, posts, struts, piers, columns and stanchions for square, rectangular or polygonal rough finished surfaces of concrete complete all as specified and directed.

Returning, filling in, including spreading levelling, watering and well ramming in layers not exc 25cm thick in any type of soil complete all as specified and directed.

Removing excavated materials (soils) not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed.

M&L for brick work with sub class 'B' bricks straight or curved on plan not exceeding 6 m mean radius built in CM 1:4 complete all as specified and directed.

M&L for preparation of newly plastered/ unplastered walls surfaces and applying three coats of white wash complete all as specified and directed.

S&F steel ventilator with top hung shutter including hinges steel peg stay complete including painting with one shop coat of zinc chromate primer complete all as specified and directed.

S&F 100 mm extruded aluminum alloy handles, fabricated type, anodised complete, all as specified and as directed.

M&L for sand filling under floors or in foundations including watering and consolidation complete, all as specified and as directed.

M&L for broken bricks hardcore of gauge n exc. 63mm, deposited, spread and levelled in layers n exc. 15cm thick, watered and rammed to a true surface complete all as specified directed.

M&L for 75mm thick cement concrete (1:4:8) type D 2 (using 40 mm graded crushed stone aggregate) as in sub bases of floors and pavings complete all as specified and as directed.

S&F Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. of Gde Fe 410- W (Gde- E-250) quality-A complete all as specified and directed.

S&F Plates (plain or chequered) channels, square cut or notched (ordinary & counter sunk) forming holes, without any attachment of Gde Fe 410-W (Gde- E- 250) quality-A complete all as specified and directed.

S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F Pre-painted galvatume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe), including provision of lime concrete bedding, connection to trap and anti syphonage pipe etc complete all as specified and directed.

S&F 10 litre capacity PVC valve less syphonic action type, flushing cistern, low level, white, with inlet, ball valve, flush pipe, float and handle including brackets complete all as specified and directed.

S&F PVC connections 15mm size with PTMT nuts of length 600mm ccomplete all as specified and directed.

S&F Stop valves, 15mm bore fancy type, chromium plated cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and directed.

S&F Vitreous China wash basin, size 550 x 400mm, white, flat back, with waste, coupling, chain and plug and porcelean stopper & backets including cutting for and pinning in ends of brackets but excluding tap complete all as specified and directed.

S&F Soap dish, vitreous China white, approximate size 160x 160x90mm complete all as specified and directed

S&F CP 15 mm bore Bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed.

S&F towel Rail 600mm long of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 190gms) complete all as specified and directed.

S&F 125mm Chromium plated shower roses with or without swivel joints, any size, including fixing to steel pipe or union complete all as specified and directed.

S&F 110 mm dia PVC (SWR) pipes single sockets, in any length with rubber ring joints, laid in trenches or floors complete all as specified and directed.

S&F 110 mm PVC (SWR) gully trap, plain with grating including jointing with solvent cement complete all as specified and directed.

S&F 75mm PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed.

S&F 75 mm dia PVC (SWR) pipes single sockets, in any length with rubber ring joints, laid in trenches or floors complete all as specified and directed.

M&L for cement concrete (1:3:6) type C-2 (using 40mm graded crushed stone aggregate) as in foundations, filling and mass concrete complete all as specified and directed.

M&L for Plain cement concrete (1:2:4) type B1 (using 20mm graded crushed stone aggregate) as in coping etc including weathering, slightly rounded or chamfered angle and throating including necessary use and waste of form work complete all as specified and directed.

M&L for rendering 15mm thick on other than fair face of brick work in cm 1:4 finished even and smooth without using extra cement, complete all as specified and as directed.

S&F 150mm dia reinforced concrete pipes, class NP2 with collar per length of pipe laid in trenches complete all specified and directed.

M&L for cement concrete (1:3:6) type C-2 (using 40mm graded crushed stone aggregate) as in concrete bed to drain pipes 150 mm internal bore including packing under and hunching against the sides of pipes after they are laid and tested, in complete all as specified and directed.

M&L for precast RCC (1:2:4) type B1 (using 20mm graded crushed stone aggregate) as in cover slab for manhole etc including necessary form work complete all as specified and directed.

M&L for Mild steel round bars 10mm dia as in handles for manhole cover complete all as specified and directed.

Cutting into existing manholes for connecting new drains of 100 mm internal dia, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement oncrete 1:2:4 type B-l smooth finished, and reforming benching as required complete all as specified and directed.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc. complete all as specified and directed.

M&L for making point wiring system with single runs of PVC insulated FRLS wire, 1100 volt grade with multistranded copper conductor wire of size 1.5 Sqmm (Nominal area) (ISI Marked) any type any length drawn through in heavy duty ISI mark PVC Casing capping suitable size & type / PVC conduit of not less than 20 mm size along with its all connected fittings accessories and duly fixed in concealed in wall or surface of wall complete all as directed by EIC including providing of pressed steel terminal sunken boxes 1.6 mm thick & duly fixed concealed in wall and covered with electro plated 3 mm thick plastic laminated sheet for housing/mounting of switches sockets, regulators etc and also using /drawing of 1.5 sqmm PVC insulated FRLS wire, 1100 Volt grade (ISI Marked) with multistranded copper conductor wire used as a continuous earth wire which is connected with terminated the box to ceiling rose / fitting complete and including making good to all disturbed surfaces of wall/ceiling and floor area of wiring system and to match the existing surface of wall/floor/ceiling etc. complete all as specified and directed.

One light point / fan point / bell point controlled by one, one way switch.

One 3/5 pin socket outlet, 5 Amps on the same board with other switches controlled by one, one way switch.

One 3/5 pin socket outlet, 5 Amps, on independent board controlled by one, one way switch.

Ditto all as per serial item number 139.00 described here-in-before but using single runs of PVC insulated FRLS wire, 1100 volt grade with multistranded copper conductor wire of size 2.5 Sqmm (Nominal area) (ISI Marked) for 3/6 pin type 15 Amp socket outlet point wiring system controlled by one, one way switch fixed on independent board and also providing of 2.5 sqmm PVC insulated FRLS wire, 1100 Volt grade (ISI Marked) with multistranded copper conductor wire used as continuous earth wire complete all as specified and directed.

S&F switch paino 5/6 Amps 230 Volts, one way (ISI Marked) complete all as specified and directed.

S&F 5/6 Amps socket AC 230 Volts 3/5 pin type (ISI Marked) complete all as specified and directed.

S&F switch paino 15/16 Amps 230 Volts (ISI Marked) complete all as specified and directed.

S&F socket 15/16 Amps AC 230 Volts 5/6 pin type (ISI Marked) complete all as specified and directed.

S&F bell push switch 5/6 Amps 230 Volts, one way (ISI Marked) complete all as specified and directed.

S&F fan regulator with hum free step type alongwith speed control knob of capacity 120 watt 230 Volts, one way (ISI Marked) complete all as specified and directed.

S&F bell Buzzer, Ding Dong type AC 230 volts, single pole (ISI Marked) complete all as specified and directed.

S&F ceiling rose three terminals type made out of polycarbonate, isolated body (ISI Marked) complete all as specified and directed.

S&F LED light fitting fixture of 20W, 6500K, 2000 lm decorative ultra slim with co extruded channel in thermally conductive material with plastic housing, heat sink, environmental friendly having power factor >0.95, surge protection 2.5KV energy efficient ready to use complete including providing of suitable type flate fexible cable for electric connection purposed comlplete all as specified and directed.

S&F flush type PVC insulated body batten / angular type lamp holder and having in side of holder with brass adaptor anlongwith back plate all fixing accessoris including duly fitted with 7/9 watt of LED chargeable bulb complete all as specified and directed.

S&F in repair/replacement of double pole and neutral enclosure with two pin and earth pug and socket complete alongwith MCB SPN, 240 Volts, 20 Amps, 10 kA rupturing capacity, 'C' series complete all as specified and directed.

S&F ventilating exhaust fan made out of sturdy high quality engineering plastic, complete with louvers and shutter operational of size 250mm sweep suitable to work on 230 Volts 50 Hz, 1200 RPM, copper winding including making of suitable type /size of hole on wall compete all as specified and directed.

S&F LED Mirror light fitting 10 W 6500K decorative ultra slim linear LED lighting fixture with extruded AL heat sink, environmental friendly, energy efficient, including providing of suitable type flate fexible cable for electric connection purposed comlplete all as specified and directed.

Taking down carefully existing ceiling fan /exhaust fan/ geyser any type sweep and removing fan blade including cleaning all dust particles and filling cavities with filler material, oiling, greasing including painting fan with blade/geyser complete one coat of synthetic enamel white paint by spraying and assemble the same along with all connecting fixing accessories like rubber rell, nut, bolt, washer, lock pin etc and hanging the same position with the help of nut bolt and washer etc along with all electrical wire connection complete all as specified and directed.

S&F Sub main wiring system with two runs PVC insulated FRLS wire, 1100 volt grade with multistranded copper conductor wire of size 3 Run of 6 Sqmm and one run of 6 Sqmm (Nominal area) (ISI Marked) any type any length drawn through in heavy duty ISI mark PVC Casing capping / PVC conduit of suitable size along with its all fittings and connected accessories and duly fixed concealed on wall or surface of wall including taking down old unservicable sub main wiring system complete and making good all disturbed surfaces match to the existing surface complete all as specified and directed.

S&F sheet metal enclosure duly powder coated with locking arrengment system and having double door TPN 4 way distribution board with IP-43 1K-09 protection system and having mounting chanel and connection bus bar system suitable for MCCB as incommer and MCB as outgoing 415 Volts 3 phase power supply, complete with appropriate size copper bus bar and neutral and earth link etc complete alongwith providing of 01 No MCCB 160 Amps rating with rupturing cap 25 KA 3 pole 415 Volts and also 12 Nos of MCB SP 63 Amps 'C' Curve of the same make as of distribution board complete & including taking down of existing DBs with MCBs and making all necessary electrical connection and dully fixed surface on wall or concealed on wall with the help of cutting chases to wall for fixing of DB and making good the disturbed wall surface complete all as specified and directed.

S&F sheet metal enclosure duly powder coated with locking arrengment system and having double door SPN 8 way distribution board with IP-43 protection system and having mounting chanel and connection bus bar system with having capacity 200 Amps and suitable size of common neutral link including taking down of existing DBs with MCBs and making all necessary electrical connection and duly fixed surface on wall or concealed on wall with the help of cutting chases to wall for fixing of DB and making good the disturbed wall surface complete all as specified and directed.

S&F MCB SPN 40 to 63 Amps, 230 Volts, 50 Hz AC supply suitable for 'C' series, 10 KA breaking capacity complete all as specified and directed.

S&F MCB SP 6 to 32 Amps, 240 Volts, 50 Hz AC supply suitable for 'C' series, 10 KA breaking capacity complete all as specified and directed.

Supply and lay GI pipe 40 mm bore medium grade with all fitting laid in trenches/ under road /floor/ pole/ wall for protection of cable including providing clamping arrangment for holding of pipe on pole/wall in proper size of clamps, nut bolt, and washer etc complete all as specified.and directed.

Supply and lay GI pipe 50 mm bore medium grade with all fitting laid in trenches/ under road /floor/ pole/ wall for protection of cable including providing clamping arrangment for holding of pipe on pole/wall in proper size of clamps, nut bolt, and washer etc complete all as specified.and directed.

Supply, laying and testing of LT cable XLPE insulated screened, PVC bedded galvanized steel strip or wire armoured electric power cable (heavy duty) with aluminium conductor 1100 volt grade cross section area of size 25 sqmm 4 core including laid in trenches or fixing on poles or passing through pipes complete including taking out of old unserviceable cable any type any size complete all as specified and directed.

M&L for Sand cushioning for under ground cable provided with a layers of sand 80mm thick before laying cable and sand 150mm thick after laying and stretching the cable complete all as specified and directed. Note: Only punned down thickness up to 180mm shall be measured and paid.

Supply and lay brick covering width equal to length of brick for mechanical protection to cable with well burnt sub class 'B' bricks laid dry flat complete all as specified and directed.

S&F LED street light fitting 45Watt with lense, toughned glass, IP 66 protection 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant with impact and corrosion resistant complete with making suitable size of bracket and MS clamps duly fixed on wall including providing of suitable type flate fexible cable for electric connection purposed comlplete all as specified and directed.

M&L for earthing, complete with galvanised steel earth plate electrode 60cmx60cmx6mm thick buried directly in ground (Earth pit not less than 2.25 meters deep below normal ground level) with top edge of plate not less than 1.5 mtr below normal ground level connecting to the galvanised iron earth lead wire of 4 mm dia by means of bolts, nuts, check nuts and washers of galavanised iron and earth strip protected by provision of GI light grade pipe 20 mm bore including provision of concrete pit in PCC (1:2:4) type B-1 (using 20mm graded crushed stone aggregate) with XPM (weight not less than 4 Kg/Sqm) and frame of angle iron 25x25x6mm with lugs 02 Nos and with 20mm bore pipe for watering perforated at bottom 1.75 mtr long placed on top edge of earth plate common salt and charcoal filling test point made out of 40mm/6mm flat iron with fixing arrangement funnel wire mesh and earth work in any type of soil returning filling in and removal of surplus soil to a distance not exceeding 50 mtrs all as per electrical plate No 03 of SSR-2009 Part-I and connecting to earth test point complete all as specified and directed.

S&F storage water heater of capacity 25 ltrs, BEE five star rated with all accessories such as safety valve, NRV etc including making all connections comlplete all as specified and directed.

S&F exhaust fan steel body AC single phase 230V of size 250mm sweep with frame and louvers etc including making connection to ceiling rose comlplete all as specified and directed.

S&F LED Secutiy light fittings 60/40 watt made out of pressure die cast aluminium housing with high power LED with lens embeded PC cover and separate driver compartment with IP 66 including making electric connetion with GI bracket of 40mm light grade 1.5M in bend shape, clamps and accessories complete all as specified and directed.

S&F 1100 Volts grade heavy duty cable weather proof PVC insulated stranded aluminium conductor served with inner sheathing of PVC tape & overall PVC sheathed in service connection suspended by insulating hanger not more than 1 meter apart including 4 mm Gl suspension wire one twin core cable flat or circular of size 10 Sqmm to be connected to existing MCB box / Main switches complete all as specified and directed.

M/S MOHAMAD YOUSUF AKHOON AND SONS

M/S SHIMAR STAR GLACIER

M/S NORTHERN ELECTRICAL WORKS

M/S MAHIR MUNEER

Concept Engineering & Constructions