Improvement and Protection Work on Y Junction of Tiyala on KM 54 of Mawana Kithore Hapur Road -SH 118-

Construction of un-reinforced, dowl jointed plain cement concrete pavement (M30 Grade) over a prepared sub base with approved grade cement @ 400 kg per cum, coarse and fine aggregates conforming to IS:383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a batching and mixing plant as per approved mix design, transported to site, laid with a fixed form or slip form paver, spread, compacted and finished in a continous operation including provision of contraction, expansion, construction and longitudional joints, joint filler, separation membrane, sealant primer, joint sealant, debonding strip, dowel bar, tie rod, admixtures as approved, curing compound, finishing to lines and grades as per drawing and rate are including all material, labour, T&P all complete as per direction of the Engineer-in-charge but excluding the cost of GST

Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35 .The finished surface to be level, uniform and free from streaks and holes and rate are including all material, labour, T&P all complete as per direction of the Engineer-in-charge but excluding the cost of GST

Providing and applying tack coat with bitumen VG-10 using bitumen pressure distributor at the rate of 0.25 kg per sqm on the prepared cleaned primed surface and rate are including all material, labour, T&P all complete as per direction of the Engineer-in-charge but excluding the cost of GST (Ref. to Mort&H Specification No.503) . (Speed Table for for Desirable speed (50 kmph)(For SH& MDR) Black Spot Tyalla(UP8111)-10.0 m Wide (BM+BC))

Providing and laying dense graded bituminous macadam with higher capacity batch type HMP using crushed aggregates of specified grading, premixed with bituminous binder @ 4.5 per cent by weight of total mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MoRTH specification clause No. 505 complete in all respects and rate are including all material, labour, T&P all complete as per direction of the Engineer-in-charge but excluding the cost of GST (Speed Table for for Desirable speed (50 kmph)(For SH& MDR) Black Spot Tyalla(UP8111)-10.0 m Wide (BM+BC))

Providing and laying bituminous concrete (Gr-II) with 120 TPH batch type hot mix plant using crushed aggregates from approved quarry of specified grading, premixed with bituminous binder (VG-30) @ 5.40 per cent of mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MORTH specification clause No. 507 complete in all respects Adjustment for bitumen shall be done as per job mix formula and E-in-C letter No 2651 Dt 27-07-12. (Speed Table for for Desirable speed (50 kmph)(For SH& MDR) Black Spot Tyalla(UP8111)-10.0 m Wide (BM+BC)) and rate are including all material, labour, T&P all complete as per direction of the Engineer-in-charge but excluding the cost of GST

Providing and Laying of I shaped grey colour Interlocking tiles rubber moulded 80mm thick precast cement concrete having plan dimension 200 x (160+120mm) with compressive strength not be less than 30 Mpa (M-30) and weight 5kg per no. specification to IS:15658-2006 as per drawings and Technical Specification Clause 1504 (Speed Table for for Desirable speed (40 kmph)(For ODR & VR) Black Spot Badnoli(UP8610)-- VR CC 7.0m Wide) and rate are including all material, labour, T&P all complete as per direction of the Engineer-in-charge but excluding the cost of GST

Provinding and laying of hot applied thermoplastic compound 15 mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 15 mm is exclusive of surface applied glass beads as per IRC:35. The finished surface to be level, uniform and free from streaks and holes and rate are including all material, labour, T&P all complete as per direction of the Engineer-in-charge but excluding the cost of GST

60 cm equilateral triangle with definition plate (SPEED BREAKER)sign board and rate are including all material, labour, T&P all complete as per direction of the Engineer-in-charge but excluding the cost of GST

90 cm Octagon with definition plate (STOP) sign board and rate are including all material, labour, T&P all complete as per direction of the Engineer-in-charge but excluding the cost of GST

90 cm equilateral triangle with definition plate (SPEED BREAKER ,T-JUNCTION) sign board and rate are including all material, labour, T&P all complete as per direction of the Engineer-in-charge but excluding the cost of GST

Supply and fixing of raised pavement marker (Cat Eye/Road stud) with Made of Plastic body of RPM/Road Stud shall be moolded from ASA (Acrylic Styrne Acrylonitrite) or HIPS (High Impact Polystyrene) or Acrylonitrite Butadien Styrene (ABS) or Any other suitable material approved by the Engineer. The marker shall support a load of 13.635 kg tested in accordance with ASTM D4280. The Reflective panels shall consist of number of lenses contatning single or dual prismatic cubes capable of providing total internal reflection of the light entring the lens face, lenses shall be mouled of meithyl methecrylate confirming to ASTM D788 of equivalent. The slop or retro-reflecting surface shall preferably be 35+/-5 degree to base and the area of each retro-reflecting surface shall not be less than 13.00 sq.cm the marker height shall not be less than 10 mm and shall not exceed 20 mm & Width shall not exceed 130 mm. The base of the marker shall be flat within 1.3 mm all road studs shall be legibly marked with the name, trade or other means of identification of the manufacture epoxy installations, excess adhesive around the edge of the marker excess adhesive on the pavement and adhesive on the exposed surface of the marker shall be immediately removed. The Contractor shall submit a two year warranty for satisfactory field performance including stipulated retro-reflecting panel, to the Engineer in addtion a two year warranty for satisfactory infield performance of the finished road marker shall also be given by the contractor who carries out the work of fixing of reflective road markers, in case the markers are displaced, damaged, get wom out or lose their reflectivity compared to stipulated standard the contractor would be required to replace all such markers within 15 days of the intimation from the Engineer, at his own cost. The rate shall include all material, labour, T&P, transportation, installation and incidentals all complete as per direction of the Engineer-in-charge but excluding the cost of GST. RPM (with Shank)

Solar Power road marker (Solar Studs) The solar studs shall be made of Aluminium alloy and poly carbonate material which shall be absolutely weather resistant and strong enough to support a load of 13,635 kg tested in accordance with ASTM D4280. Its colour may be white , red , yellow , green or blue or combination as directed by the Engineer . Its water resistance shall meet the requirements of IP 65 in accordance with IS:12063:1987 category 2 for protection against water ingress.The dimensions of solar studs shall not be less than 100 mm X 100 mm X 10 mm . It shall have super bright LEDs so as to provide long visibility from a distance of more than 800 m. Its flashing rate shall not be less than 1 Hz . Its should be able to give the prescribed performance in the temperrature range of - 400C to +550C. Its life shall be not less than 3 Years. The rate shall include all materials, labour, equipments, fabrication, transportation, erection, installation and incidentals all complete as per direction of the Engineer-in- Charge but excluding the cost of GST ( Solar Studs)

Solar Power road Bkinker light The rate shall include all materials, labour, equipments, fabrication, transportation, erection, installation and incidentals all complete as per direction of the Engineer-in- Charge but excluding the cost of GST

Please Enable Macros to View BoQ information