REPAIR TO JOINERY, PLUMBING, FALSE CEILING, PLASTERING, PETTY REPAIR TO OTM, MD ACCN, PERIODICAL SERVICES AT VIP AREA, B ZONE AND CERTAIN MISC UNITS UNDER AGE B/R-I OF GE BENGDUBI MIL STN

Amount

SCHEDULE 'A'

Note for serial item No 1 to 121: - (i) The contractor shall provide one supervisor/ storekeeper to report at complaint cell/office in the morning by 9:00 Hrs to receive day to day complaints along with tradesmen;- (a) Carpenter-1, (b) Plumber-2 Nos, (c) Mason-1, (d) Mazdoor-2 Nos, (e) Welder-1. (ii) Complaint should be attend/completed within 48Hrs after receiving complaint slip failing which a panel recovery @ double the quoted rate of each complaint will recover from contractor dues or become dues(i.e. RAR/FB) (iii) Debris materials obtain from demolition/dismantling shall be removed from the site, outside Md land, Failing which a panel recovery from contractor Rs 500.00 per cum will be recovered from contractor dues or become dues (i.e. RAR/FB). (iv) The unit rates quoted by contractor in BOQ shall be deemed to include for above provision and no extra claim will be entertained by the Department at late date in this respect.

Taking down chowkats or frames with shutter(without taking off shutter from the frame) area not exc. 1.5 sqm complete all as specified and directed

Taking down chowkats of any description without taking of shutter from the frame exceeding 1.5 sqm but not exc. 4.0 sqm each all as specified and directed

Taking down shutters of any description exceeding 1 sqm but not exceeding 2 sqm each and removing form site of work.

S &F Pressed steel frames frame size 165X60mm for doors with one or moe rebates including necessory fixing lugs, hinges, lock strike plates etc, complete, all as specified.

S&F of 30 mm thick flush shutter solid core construction with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

S & F 2nd class HW glazed and skeleton 30 mm thick window shutters open rebated and prepared to receive glass, gauze etc with plain, chamfered or rounded, mitred and rebated sash bars, any numbers, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc, sites of members of shutters as specified in SSR Part-I, section 8, clause 8.24 (b) Window complete all as specified and directed.

S&F 35mm thick plain framed, panelled shutter (three panel) with lock rail and panel of 9mm B.W.P. commercial ply. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated all as specified and directed.

M&L for preparation of new wood and wood based surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

S & F factory made solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube as per specification and drawing.

S&F Factory made Solid PVC Moulded Door Shutter, 28 to 30 mm thick (Stiles), with 2,4, or 6 raised panel design with 2 mm thick 3D wood grain Moulded PVC sheet Polyurethane painted on the front face & 2 mm plain colour PVC sheet on back face with particle Board core complete all as specified and directed.

S&F mild steel sliding door bolts plate type 300mm bolt not less than 16mm dia with and including a minimum of 6 bolts and nuts all as specified and directed.

S&F stainless steel butt hinges medium weight 100mm in size

S & F 150 mm aluminium handles cast type anodised.

S&F mild steel barrel tower bolts of extruded section and fixed 200 mm size all as specified and directed

S&F in repairs 300 mm long aluminum alloy anodised sliding door bolt hasp staple (bolt type) and fixed clips of sheet cast or extruded section fixing bolts and sliding bolts of extruded section all as directed ( As per sample).

S&F in repairs aluminium handle 150mm size cast type, anodised, ISI marked complete all as specified and directed.

S&F in repairs 150 mm long aluminium anodised barrel tower bolts of extruded section all as specified (Make : As aper sample)

S&F in repairs stainless steel butt hinges medium weight 100mm in size complete all as specified and directed.

S&F in repairs steel window handles with complete fitting , peg stays & Hinges etc (Including welding if required) as per sample complete all as specified and directed.

Supplying and fixing steel windows with side hung shutters including projection type hinghs with steel handle, and steel pag stay, complete with glazing bars, dovetailed or welded complete all as specified and directed.

Supplying and fixing steel windows with side hung shutters including projection type hinghs with steel handle, and steel pag stay, complete without glazing bars, dovetailed or welded complete all as specified and directed.

Supplying and fixing steel ventilators with top hung shutter including hinges, steel peg stay complete all as specified.

S&F Galvanised mild steel wire cloth, 0.63mm nominal dia of wire and average width of apertune 1.40 mm and fixed with tinned tacks ,or galvanised wire staples including necessary beading complete all as specified and directed.

S & F in repairs Galvanised mild steel wire cloth, 0.63mm nominal dia of wire and average width of apertune 1.40 mm and fixed with tinned tacks ,or galvanised wire staples including necessary beading complete all as specified and directed.

Easing of door/windows shutters of any size/any number of pannels for easy closing/opening tightning of hinges or changing the position of hinges adjustments of lower bolts. Sliding bolts etc complete all as directed.

M&L for Welding in repairs of thickness of metal to be welded exc. 6 mm but not exc. 9 mm and not exc. 2.5 cm in length complete all as specified and as directed.

Hacking out old broken glass (any thickness size quality and discription) for metal frame including punching, drilling out old glazing pins / spring clips and providing new ones complete all as specified and directed.

S&F figured glass pin head type 4 mm thick and glazing with oil putty in squares exc 0.5 Sqm in each pane complete all as specified and directed.

S&F 4.00 mm thick sheet glass, ordinary quality and glazing with oil putty in squares n.exc 0.5 Sqm in each pane complete all as specified and directed.

M&L preparation of new steel surface and applying two coats of synthetic enamel paint over a coat of primer red oxide primer including preparation of surfaces complete all as specified and directed.

S&F Powder coated Anodised aluminum frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc complete all as specifed.

S&F for Powder coating anodised aluminium door shutters, aluminium section weighing 0.55 kg/m including joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc complete all as specified and directed

S&F for Powder coating anodised aluminium window and ventilator shutters, side hung type without sash, aluminium sections weighing 0.55 kg/m including joining cleats, glazing clips, rubber neoprene packing, anodised aluminum snap beading, screws, anodised aluminium fittings such as peg stays 150 mm long (1 no.) hinges type B-21 100 mm long (2 no) suitable handle (1 no) etc complete all as specified and directed

Taking down unserviceable Aluminium door/window shutters including taking out all unservicable parts, and repairing defective portion of shutter, and refixing in the same opening complete all as specified and dirtected.(Repairable items glass pane, mortice lock, mesh grill paid separately)

M&L 100x100mm size mesh aluminium anodised grills of approved designs complete all as specified and directed.

S&F mortice lock vertical type barss 100mm size 4 levers

S&F double action floor spring hydrualically regulated made up of minimum 12.5 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover governing pivot made of brass other parts made of mild steel heavy duty and fixed complete all as specified and directed.

M&L for 5.5 mm thick sheet glass ordinary quality frosted or one way including glazing clips, rubber packing etc exc. 0.5 sqm in each pane complete all as specified and directed.

Dismantling of wall and ceiling boards (fibre, pulp, insulation, etc) or insulation boards/ slabs/ blankets any thickness, including cover fillets.

S&F 605 x 605 mm GI frame work for seamless ceiling comprising of GI perimeter channel 0.55mm thick with two unequal flanges of 20 & 30mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm centre to centre/intermediate channel 0.9mm thick having two equal flanges of 15mm each and web of 45mm suspended from soffit at approx 900mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section(not exc 1.2m length) of 0.55mm thickness having kurled web of 50mm and flange of 26mm each with lips of 10.50mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457mm centre to centre complete all as specified and directed.

S&F Hangers 4mm dia GI (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40x3mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified and directed.

M&L for Providing and fixing 10mm thick plaster of paris ceiling (Gypsum anhydrous) to flat surface over II class soft wood fillets and reinforced with G.I. wire mesh (Fillets and G.I. wire mesh paid separately) complete all as specified and directed.

Dismantling floor, hearth or wall tiling incl cement mortar bedding (but not backing and rubbish off the premises complete all as specified and directed..

M&L for non skid ceramic tiles joint free coloured tiles 7mm to 8mm area exceeding 0.11sqm but n.exc 0.18 sqm on floors over and incl15mm thick screed bed in CM(1:6) set jointed in neat cement slurry and pointed with colour cement to match the tiles complete all as specified and directed.

M&L for glazed coloured ceramic tiles joint free coloured 300 X 450 mm size 7mm thick on walls over and incl 10mm thick plastering in CM(1:4) set jointed in neat cement slurry and pointed with colour cement to match the tiles complete all as specified and directed.

Dismantling PVC water tanks 1000 litres capacity.

Dismantling PVC water tanks 500 litres capacity.

S&F rotational moulded polyethylene water storage tanks of capacity 1000 litres (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I complete all as specified and directed..

S&F rotational moulded polyethylene water storage tanks of capacity 500 litres (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I complete all as specified and directed.

S&F in 20mm bore, gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe all as specified.

S&F of Ball valves 20 mm high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic bal screwed for iron pipe and fixed. (Minimum weight 15mm-142 gms/ 20mm-210 gms/25mm-455gms/ 40mm- 690 gms/ 50mm-1240 gms) complete all as specified and directed.

S&F in repairs Ball valves 20 mm high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic bal screwed for iron pipe and fixed. (Minimum weight 15mm-142 gms/ 20mm-210 gms/25mm-455gms/ 40mm- 690 gms/ 50mm-1240 gms) complete all as specified and directed.

S&F in repairs in ball valve of PVC complete with aluminum rod with polyplast ball for 15mm dia iron pipe complete all as specified For low level flushing cistern complete all as specified and directed.

S&F in repairs PVC sintex water storage tank lid cover (Cylindrical) for 500/1000 ltrs capacity tanks (Make : as per sample) complete all as specified and directed.

Disconnecting existing tanks,Exc 250 & n exc 500 setting aside (or lowering if required) for repairs, cleaning, etc. and hositing if required reconnecting and re-fixing in position. (Cleaning repairing etc. measured separately).

Disconnecting existing tanks,Exc 500 & n exc 1000 setting aside (or lowering if required) for repairs, cleaning, etc. and hositing if required reconnecting and re-fixing in position. (Cleaning repairing etc. measured separately).

Cleaning and removal all scales and dirt etc from tanks and from mouths of circulating pipe etc for 500 ltrs and 1000 Ltr capacity of tanks icnluding written as "Tank cleaned on DD-MM-YYYY" on the body of the tank with white paint complete all as directed.

Taking down steel tubing and connection 15mm bore.

Taking down steel tubing and connection 20mm bore.

Taking down steel tubing and connection 25mm bore.

S&F G I tubing medium grade, galvanised with all fittings and fixed complete to wall and ceiling or laid in floors bore of tube 15 mm all as specified and directed.

S&F G I tubing medium grade, galvanised with all fittings and fixed complete to wall and ceiling or laid in floors bore of tube 20 mm all as specified and directed.

S&F G I tubing medium grade, galvanised with all fittings and fixed complete to wall and ceiling or laid in floors bore of tube 25mm all as specified and directed.

M&L for cutting, chases, pinning in block masonry wall for concealed water tubing and making good to facing and pointing in CM 1:3, cutting n. exc. 10 cm girth all as specified and directed.

Refixing the following old steel tubing and connections in new or old position (Walls, ceiling, floors, etc.):-

15 mm bore

20 mm bore

25 mm bore

S&F in repairs small fittings galvanised iron medium grade such as sockets, elbow , nipple up to size 200 mm , tee , union etc for 15mm bore pipe (ISI Mark all as directed)

Ditto all as per Srl Item No 69.00 above but for 20mm bore pipe

Petty repairs to leaking in bib tap, pillar tap, stop cock, Angle valve and low level flushing cistern etc of any description including changing the washer etc all as specified.

Removal of air lock/blockage of water in GI tubing 15 mm/20 mm bore cleaning the pipe or fittings etc and refixing the same in position all as specified.

S&F in repairs 32mm dia PVC waste pipe flexible type for WHB 60cm long with union all as specified

S&F in repair Bottle trap of PTMT 32 mm dia having minimum water seal of 25mm complete all as specified.

S&F in repair 15mm bore CP cast copper alloy bib taps short body with wall flange fancy type complete all as specified and directed.

S&F in repairs waste fittings brass chromium plated 32mm dia for wash hand basin all as specified

S&F in repair Bip tap standard of PTMT any colour screwed for iron pipe and fixed (Minimum weight 15mm - 90gms) all as specified.

S&F in repairs Towel rail 600mm long of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats. (Minimum weight) 190gms) all as specified.

S&F Aluminium anodised towel rail , 20 mm dia, D type, 60 cm long between flanges complete all as specified and directed.

S&F in repairs CP brass shower rose 125 mm dia complete all as specified and directed.

S&F in repairs 10 lits capacity PVC flushing cistern low level, white, with inlet, ball valve, float and handle flush pipe including brackets etc complete all as specified and directed.

S&F in repairs Flush pipe of polyethylene of low or high density of PVC, 32 mm dia, for low level cistern complete all as directed ( Make : as per sample)

S&F in repairs plastic water closet seat cover white /colour ,closed pattern with flat bottom end cover and mild steel chromium plated hanging device complete all as specified and directed.

S & F in repairs viterious china wash basin white flat back size 550 x 400 mm excluding taps waste chain and plug and porcelain stopper but incl necessary brackets CP waste coupling 32 mm dia, PVC waste pipe 32 mm dia and other fittings all as specified and directed.

S&F in repairs pillar taps, 15mm bore fancy type, cast copper alloy with capston heads, chromium plated, screwed down high pressure with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and directed.

S&F 15mm dia PVC connection with PTMT nuts of length 450mm complete all as specified

S & F in repairs water closet (Squat Pattern) complete incl provn of lime concrete bedding Orissa pattern size 580 x 440mm white integral foot rests (excluding flushing cisterns) including connection to trap and flushing pipe anti syphonage pipe etc complete and making good to floor.

S&F in repair wash down water closet vitreous china pan pedestal pattern white including plastic water closet seat white, closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging device complete all as specified and directed.

S&F in repair angle cock cast copper alloy fancy type , chromium plated screwed down , high pressure,with crutch or butterfly handle, screwed both ends for iron pipe 15 mm bore complete all as specified.

S&F in repair Stop valves 20 mm bore, cast copper alloy screwed down high presure, with crutch of butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and directed.

S&F in repair toilet paper holder of CP fixed to walls with chromium plated (CP) brass screws complete all as specified and directed.

S&F in repair sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 mm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed.

S & F in repairs Stainless steel sink, 1.00mm thick for kitchen or laboratory, with plug, waste pipe, washers, including cantilever cast iron brackets, connecting union etc., overall size 495mm x420mm with bowl size 410mm x330mm x160mm complete all as specified and directed.

S & F in repairs Kitchen Sink with drain board made of stainless steel 1mm thick with plugs washers and waste pipe incl bedding in CM to dwarf wall incl fitting cantilever brackets and connecting union to pipe over all size 915mm x 460 mm and bowl size 410 mm x 330mm x160mm complete all as specified and directed.

S&F in repairs Steel plate rack made of 1mm thick stainless sheet of overall size 90 x 77 x 23 cm with providing necessary partition shelves & hanging arrangement etc as per manufacturer trade pattern as approved and fixed to wall with wooden plug with brass chromium plated screws complete all as specified and directed.

S&F in repairs brass chrome finish health faucet with 8mm dia, 1.2m long flexible tube and wall hook complete all as specified and directed.

S&F looking mirror 450X600mm with plywood backing and aluminium frame complete all as specified and directed.

Repairs to cup boards including easing of CB shutters, tightning of hingers or handles/knobs hasp and staple etc complete all as specified and directed.

M&L in repairs of wooden beads 2nd class hard wood of any size for cup board & glazed or gauged joinery mitres etc complete all as specified and directed.

Fixing only in repairs loose existing pelmet boxes made of 19 mm thick block board by embedding wooden guttles in cement mortar (1:3) with MS clips and screw etc length of pelmet box not exc 1.5 mtrs complete all as specified and directed.

Ditto all as per Ser Item No 100.00 above but length exc 1.50 M and not exc 2.50 M.

Dismanting boarding plywood etc of any description and in any position fixed with nails etc all as directed.

M&L of 19 mm thick Block boards/ Commercial board , grade 2 quality, interior grade, commercial type, fixed with screws to timber frame-work for Kitchen cabinet shutter /Almirah shutter etc including 0.90mm thick Decorative laminate type 1, of surface finish, colour and pattern as approved,fixed with approved adhesive on Both face of Board as per maker's instructions complete all as specified and directed.

M&L for Decorative laminate type 1, 0.9 mm thick, of surface finish, colour and pattern as approved,fixed with approved adhesive as per maker's instructions complete all as specified and directed.

S&F in repair 30mm width Continuous (piano) hinges, mild steel, bright finish or electrogalvanised complete all as specified and directed.

S&F in repairs 100mm Hasp and staple, mild steel, wire type, stove enamelled black, including bolt to hinge plate and fixed with screws complete all as specified and directed.

S&F Magnetic door catch stopper holder (Size : 6cm) complete all as specified and directed.

S&F in repairs 40 mm dia cup board knobs fixed with nuts, screws and washers of mild steel bright finish all as specified (Make : As per sample)

M&L of 20 mm dia MS Curtain Fancy type PVC coated rod fixed in repair complete all as specified and directed.

M&L for Fancy type caps/ side Bulbs PVC powder coated suitable for curtain rod fixed in repair complete all as specified and directed.

S&F in repairs aluminium (extruded section) door closer hydraulically regulated, designation No 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80kg and fixed complete all as specified and directed.

S&F in repairs Ball catches with 8mm dia steel ball, and brass body and striking plate of overall 150mm length including letting in and fixed

S&F in repairs PVC connection pipe 600 mm long with two Nos CP nut threaded coupling for 15 mm dia pipe complete all as specified and directed.

Supply and fix in repairs PVC (SWR) pipes 75mm bore single socketed in any length with rubber ring joints fix to wall l all as specified.

S&F in repairs PVC (SWR) pipes 110mm bore single socketed in any length with rubber ring joints fix to wall l all as specified.

S&F PVC (SWR) Bends (any radius ), diminishing pieces or tapers, bore of pipe 75mm, complete all as specified.

S&F in repairs PVC (SWR) Bends (any radius ), diminishing pieces or tapers, bore of pipe 110mm, complete all as specified.

S&F in repairs PVC (SWR) Branch pieces, double (double Y )equal or unequal of pipe 75mm bore complete all as specified.

S&F PVC in repairs (SWR) Branch pieces, double (double Y )equal or unequal of pipe 110mm bore complete all as specified.

S&F in repairs PVC floor trap, with grating 75mm including jointing to wast pipe fixed in cement concrete type B1 (1:2:4) ,in repairs and including waterleak proor treatment complete all as specified

Taking down unservicable steel gate/shutter of any description of size exc 9 sqm and n.exc 12 Sqm each including taking out of unservicable parts/portion by cutting and replacing with new one as per the existing size and specification and refixing in the same opening by maintaining proper alignment including repairing defective portion of gate/shutter, steel structurre to match with exsiting structure including necessory cutting, drilling, welding and reveting etc, greasing, oiling to movable parts including all necessory fittings and appying one coat of synthetic enamel paint over a coat of pink primer to new portion/structure complete all as specified and directed.

S&F Powder coated for anodised aluminium window and ventilator shutters, fixed type without sash bar, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, anodised aluminum snap beading, screws etc complete all as specified and directed.

Dismantling plain or corrugated PPGI/steel sheeting, any gauge, thickness in roof coverings.

S&F Pre-painted coloured trapezoidal profiled Galvalume / Zincalume sheet with min thickness of 0.50 mm TCT confirming to IS-513 (AZ-150 GSM, AI Zn alloy mettalic coating with 550MPA yield stress as per AS-1397) as in roof covering/cladding to wall fixed with self tapping screws colour/exterior coat of silicon modified polyster/BHP x RW paint system 20 micron top coat applied over 5 micron primer and 5 micron poyster back coat applied over 5 micron primer, all fixed with Galvanised self drilling self tapping fastener (12-14 x 55 with EPDM seals) complete as specified etc complete all as specified and as directed.

S&F Pre-painted coloured plain profiled Galvalume / Zincalume sheet with min thickness of 0.60 mm TCT confirming to IS-513 (AZ-150 GSM, AI Zn alloy mettalic coating with 550MPA yield stress as per AS-1397) as in roof ridge colour/exterior coat of silicon modified polyster/BHP x RW paint system 20 micron top coat applied over 5 micron primer and 5 micron poyster back coat applied over 5 micron primer, all fixed with Galvanised self drilling self tapping fastener (12-14 x 55 with EPDM seals) complete as specified etc complete all as specified and as directed.

S&F colour coated tile profile roofing sheet with 0.45mm to 0.50mm thickness complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for etc complete all as specified and directed.

M&L for Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance with pieces, cleats etc and fabrication works Fe-410-W (Gde -E-250) quality 'B' all as specified and directed.

M&L for Vitrified ceramic tiles(light shade/double charged/ultra charged) 10 mm thick ( square / rectangular) polished, area of each tiles n. exc 0.42 Sqm in floor etc. set and jointed and incl 20mm thick screed bed in CM(1:6) set jointed in neat cement slurry and pointed with colour cement to match the tiles complete.

Ditto all as per item No 129.00 here in before but as in skirting.

Demolition of cement concrete (unreinforced) in ground floor and in paving not exceeding 15 cm thickness (below or above ground level) complete all as specified.

M&L for PCC 75mm thick 1:4:8 type D2 using 40mm graded stone aggts as in floor,path dtc finishing the surface rough to receive tilies complete all as specified.

M&L for pre polished coloured cement concrete chequred tile of approved quality size 300X300X 25mm thick on floors over and including 20 mm thick screed bed CM 1:6 set and jointed in neat cement slurry and pointed with colour to match th tiles complete all as specified and directed.

M&L for providing Machine pressed precast conctete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade with grey cement and pigment complete all as specified and as directed.

M&L 25mm thick sand cushioning under floor including levellingall as spd and directed.

M&L for providing PCC Type C2 1:3:6 (40mm graded aggregate) for supporting interlocking tile all as specified and as directed

Dismantling of stone slab and tiles of any description or thickness in cooking platform laid bedded and pointed in any mortar.

M&L for machine cut kota stone slab flooring 20-25mm thick over 20 mm thick cement screed bed in CM 1:6, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete.

Ditto as above item no 34 but in skirting on backing coat of cement mortor 1:4

M&L Granite slab 20 mm thick machine cut bedded and jointed with grey cement and pointed with white cement and adhesive of pigment to match the shade incl cutting and polishing all as directed.

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc and including removal of debris and rubbish from the site etc complete all as specified and directed.

M&L rendering 15 mm thick in cement mortar (1:6) on fair faces of brick work or concrete surfaces finishing the surfaces fair and even without using extra cement complete as specified and directed.

M&L rendering 15 mm thick in cement mortar (1:4) on fair faces of brick work or concrete surfaces finishing the surfaces fair and even without using extra cement complete as specified and directed.

M&L rendering 5 mm thick in cm 1:3 over/soffit of chajja finished surface even and smooth with out using extra cement all as specified and directed.

M&L for Preparation of newly plastered surfaces of walls and applying two coats of cement base paint over a coat of white cement primer including preparing surface of cement base even and smoothcomplete all as specified and directed.

M&L Preparation of newly plastered surfaces of walls and applying two coats of oil bound distemper preparing surface of wall even and smooth over and smoothappying with 1mm thick wall care putty complete all as specified and directed.

M&L for preparation of new plastered surfaces of ceiling and applying three coat white wash complete all as specified and directed.

M&L for washing, rubbing down and stopping of distempered and painted surfaces and applying one coat of cement based paint (any tint) on walls complete all as specified and directed.

M&L for one coat of oil bound distemper on old surfaces of wall including preparation of old undecorated surfaces complete all as specified and directed.

M&L for preparation of old pained wooden surfaes of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint any tint all as specified and directed.

M&L for preparation of old wall painted surface and apply two coats of plastic emulsion paint over a coat of primer with 1mm thick wall care putty complete all as specified and directed.

M&L for preparation of old wall painted surface and apply two coats of Apex paint over a coat of primer with 1mm thick wall care putty complete all as specified and directed.

M&L for preparation of old painted steel surfaces of any description not otherwise described over 10cm width or girth and applying one coat of synthetic enamel paint any tint all as specified and directed.

M&L for preparing plastered or unplastered old surface of walls including brooming down or scrapping down with steel wire brushes, smoke soot, moulds, moss efflorescent salts and trading oil and greasy spots and applying one coat of white (Lime) wash on wall complete all as specified and directed.

All as specifed in above item No. 50 above but applying one coat of white (Lime) wash on ceiling.

Rewriting repainting existing writing letters or figures (block roma, roman, italic, Indian n exc 30 cm height)

Uprooting of vegetation growth from walls, roof chajja gutter cleaning the surface and making good holes with cement mortar (1:3) each hole not exceeding 0.10 Sqm

Supplying and laying of CPVC pipes 16mm diameter SDR 11 & plain CPVC SDR 11 fittings in trenches complete all as specified and directed.

Supplying and laying of CPVC pipes 20mm diameter SDR 11 & plain CPVC SDR 11 fittings in trenches complete all as specified and directed.

M&L for cutting, chases, pinning in block masonry wall for concealed water tubing and making good to facing and pointing in CM 1:3, cutting n. exc. 10 cm girth all as specified and directed.

S&F in repair Bottle trap of PTMT 32 mm dia having minimum water seal of 25mm complete all as specified.

S&F in repair Stop valves 15 mm bore, CP, fancy type, cast copper alloy screwed down high presure, with crutch of butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and directed.

S&F central hole basin mixer swan neck pillar tap cost copper alloy with capstan head chromium plated , screwed down high pressure with or without lettered hot or cold with long scewed shank and fly nuts screwed for iron pipe of 15 mm bore complete all as specified and as directed (Make -JAQUAR, Cat No CON-167-B)

S&F chromium plated wall mixture with or without lettered hot or cold including telephonic shower arrangment including joints to steel pipes or unions and plugging and screwing to walls complete all as specified and as directed (Make: JAQUAR cat No : CON-217)

S&F coloured vitreous china EWC super constellation P/S with P or S trap including cistern with lid super constellation, seat cover super constellation (coloured), jet spray and cistern fitting super water saver complete set super constellation dual flush all as specified and directed. Make(Hindware cat No 20032, EWC) and Cat No 21020 for cistern)

S&F towel rail 600 mm long of brass CP fancy type.(Make-JAQUAR,Cat. No -1111N)

S&F toilet paper holder premium approved quality .(Make- JAQUAR, Cat No-con1151N)

S&F in repair soap dish of best quality complete all as specified(MAKE-JAQUAR, CAT NO-CON 1131N)

Suppy and fixing Vitrious china urinals bowl type (Back or corner wall type ) complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with and including 60mm long brass screws pointing around urinal back in cement with brackets, flush pipes, grating and union for discharge pipe etc complete al as directed.

S&F for 8 to 12 mm thick Looking mirror finished surface fixed to wall with stainless steel screw complete all as specified.

S&F PVC (SWR) junction double (double T) equal or unequal of pipe 110mm bore complete all as specified.

S & F in repairs PVC connection pipe 600 mm long with two Nos CP nut threaded coupling for 15 mm dia pipe.

(Note : The Scope of Work contained in 'Sch of Credit' amounting to Rs. 98,200.00 (refer Tender Srl Page No 39). The Quoted sum shall be arrived at after deducting the amount of “Sch of Credit” from the total amount of the ‘BoQ’

AMULYA KUMAR ROY

M/S UTTAM ENTERPRISES

SHRI S K BHATTACHARJEE

M/S KAR CONSTRUCTION

BISWAJIT SAHA

UNIVERSAL CONSTRUCTION

MUKHERJEE ENTERPRISE