ADDITION/ALTERATION AND SPECIAL REPAIRS TO VARIOUS MARRIED ACCOMMONDATION AT ARTY CENTRE HYDERABAD UNDER GE GOLCONDA

Dismantling of AC sheets / Galvolume sheet / GI Sheet of corrugated or semicorrugated etc. sheets in roof coverings complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

Dismantling timber scantlings 40 Sq cm and over in section in any position, unframed work complete all as specified and directed.

Supply and fix MS Angle sections as in main and cross beams, posts, hip and jack rafters; purlins where connected to common rafters and drilling holes for existing wooden/steel angle rafter; fixed with angle cleats MS Screw bolts necessary welding to purlins or other connecting plate of Grade Fe 410 -W (Gde- E- 250) quality- A etc. complete all as specified and directed.

Material and labour for Steel work in Square hollow tubular section in horizontal framing for eves boardings including securing bolts/ screwing including all necessary drilling or riveting, etc, and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed

Material and labour for preparation of new or previously untreated steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and directed

Supply and fix pre-painted galvalume aluminium zinc coating GI based corrugated sheet 0.50 mm thick of any colour having tensile strength 550 mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed.

Supply and fix pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed.

Complete removal of existing roof treatment of any description including screed bed and roof padding completely and remove all the debris from site and rubbish off the premises complete all as specified and directed.

Material and labour for roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc brushing neat cement slurry with 3 kg of cement per Sqm complete all as specified and directed.

Material and labour for providing cement concreate type B0 1:2:4 (12.5mm graded stone aggregate ) as in padding and benching & filletting with integral water proofing compound (water proofing compound will be measured and paid seperately ) complete all as specified and directed.

Material and labour screed bed or bedding layer 10mm thick CM 1:4 for laying floor finishes finished even and smooth without using extra cement with integral water proofing compound (water proofing compound will be measured and paid seperately ) as in roof slabs complete all as spcified and directed.

Material and labour for water proofing treatment with APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) land on primed surface by forced application complete all as specified with non woven polyester matt black finished over compatiable primer at 0.3 litre per sqm, torching the membrane on whole surface uniformly while unrolling the membrane by LPG and sealed with trowel after necessary preparation of surface complete all as per manufactures instructions and finally finished with at coat of bitumastic aluminium paint over the membrane. complete all as specified and directed. The over lap joint shall be provided of 100mm in longitudinal direction and 150mm in tranverse direction respectively. All the angles, abutments and the drainage outlets shall be sealed with extra care to ensure full bondage. Note : The work shall be carried out by authorized applicators of manufacturers.

Demolition of brick work or stone/boulder masonry, built in cement mortar inculding all quoins,pillars etc complete all as specified and directed.

Material and labour for brick work with sub-class `B' bricks, straight or curved on plan exceeding 6 M mean radius built in cement mortar 1:6 complete all as specified and directed.

Material and labour for brickwork with sub class ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified and directed.

Taking down cement plaster on wall of any desdriptions including racking out joints for key scrubbing with water and removing the debrish to outside MD land, etc.complete all as specified and directed.

Material and labour for 15 mm thick rendering in two layers, 5mm thick in CM 1:4 mixed with water proofing compound @ 3% by weight of cement over a coat of 10mm thick in CM 1:4. on concrete or brick wall surfaces, finished even and smooth without using extra cement (water proofing compound will be measured and paid seperately ) complete all as specified and directed.

Supply only integral water proofing compound.

Material and labour for rendering 10mm thick in cement mortor 1:6 on Brick wall surfaces, finished even and smooth without using extra cement complete all as specified and directed.

Material and labour preparing the newly plastered wall surfaces, applying 2mm thick (two layers of 1mm each coat) wall care putty to fill up the depression and rubbing it with sandpaper to achieve a levelled and smooth surface and applying two coats of acrylic distemper over a coat of alkali-resistant primer complete all as specified and directed.

BLANK

Material and labour for preparing new plastered surfaces of walls And applying two coats of cement based paint all as specified and directed.

Material and labour for rendering 5mm thick in CM (1:3) as in ceiling, concrete surfaces finished even and smooth (without using extra cement) complete all as specified and directed.

Material and labour for preparation of new ceiling surfaces and applying three coat of white wash, complete all as specified and directed.

Material and labour for complete removal of existing treatment on walls and applying 2mm thick (two layers of 1mm each coat) wall care putty to fill up the depression and rubbing with sandpaper to acheve a levelled and smooth surface and applying two coats of acrylic distemper over a coat of alkali-resistant primer complete all as specified and directed.

Material and labour for complete removal of existing treatment and applying two coats of cement base paint on walls surfaces complete all as specified and directed.

Material and labour for preparation of old ceiling surfaces and applying two coats of white wash, complete all as specified and directed.

Dismantling Stone slabs and tiles of any description or thickness in floors, plinth protection, aprons etc laid, bed-dry and pointed in any mortar complete all as specified and directed.

Demolition of cement concrete (unreinforced) of any description of any position not otherwise specfically provided for as in floor, etc complete all as specified and directed.

Material and labour for PCC type E2 1:5:10 (Using 40mm graded stone aggregate) as in foundations, filling and mass concrete complete all as specified and directed.

Material and labour 20mm thick for PCC 1:2:4 type B0 using 12.50mm graded aggregate in sub base floor, fillings & mass concrete complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish of the premises complete all as specified and directed.

Material and labour for roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc complete all as specified and directed.

Material and labour for non skid coloured ceramic tiles 7 to 8mm thick (square or rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc,laid over including 15mm thick cement (1:6) tiles jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed

Material and labour for non skid coloured ceramic tiles 7 to 8mm thick (square or rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc,laid over including 15mm thick cement (1:6) tiles jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

All as per item no 36 here in before but for vertical surface such as skirting,dados and riser to steps over and including 10mm thick backing coat in cement plaster 1:3 finished even and fair to receive tiles complete all as specified and directed..

Material and labour for glazed coloured ceramic tiles in vetical surfaces of size 450mmx300mmx7mm thick laid over 10mm thick back coat in CM (1:4), set and jointed in neat cement slurry and pointed in white or colour cement to match the colour of tiles, complete all as specified and directed.

Material and labour vitrified ceramic light shade tiles 9 to 10 mm thick (square/ rectangle) polished, area of each tiles not exceeding 0.36 sqm,in floor etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match flooring (in any pattern) and jointed with coloured cement matching with surface of tiles as in floor 15mm thick cement screed in CM 1:6 and pointed with coloured cement matching with surface of tiles as in floor complete all as specified and directed complete all as specified and directed.

All as per item no 39 here in before but for vertical surface such as skirting,dados and riser to steps over 10mm thick backing coat in cement plaster 1:3 finished even and fair to receive tiles.

Material and labour mirror polished machine cut Kota stone slab 20 to 25 mm thick kota stone slab single piece to the full width of tread and window Cill. Tread kota stone shall be provided with bull nosing and 02 nos of 5 mm thick anti skid grooves at one side of tile over and including 20 mm thick screed in CM 1:4 over cement slurry over RCC slab / waist slab complete all as specified and directed.

Material and labour mirror polished Machine cut kota stone slab flooring 20 to 25mm thick over and including 20mm thick screed in CM 1:4 over PCC sub base/RCC slab. laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

Material and labour mirror polished machine cut Kota stone slab 20 to 25 mm thick in riser of step, skirting, dado & pillar laid over and including 10 mm thick backing coat in CM 1:3 jointed with grey cement slurry mixed with pigment to match with the shade of the slab including rubbing and polishing complete all as specified and directed.

Material and labour for 75mm thick PCC 1:3:6 type C2 (Using 40 mm graded granite stone aggregate) as in plinth protection / Hardstanding finished even and smooth without using extra cement complete all as specified and directed.

Demolition of cement concrete (reinforced) as in roof, floor (other than ground floor) beams, staircase, landing ,chajjas, RCC water tanks and similar suspended work complete all as specified and directed.

Material and labour for Reinforced Cement Concrete 1:2:4 type B1 (using 20 mm graded aggregate) as in Cover slab for manholes etc set in cement mortor 1:4 including necessary form work complete all as specified and directed. (Reinforced shall be measured and paid seprately).

Material and labou mild steel TMT bars 10mm dia and over , cut to length bent to shap required including cranking, bending spirally for hooping for column shooking ends and binding with and including mild steel wire (annealed not less than 0.9 mm dia or securing with clips complete all as specified and directed.

Material and labour 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like laid over and including 20mm thick cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.

Material and labou for Rounding to edge of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified and directed.

Excavating in trenches n exc. 1.5m Wide and n exc. 1.5m in depth, for foundation, laying of pipes, Cables, etc. or for shafts, wells cesspits, manholes pier holes, etc. n exc. 10 sqm on plan and getting out in hard /dense soil complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm, thick with all kind of soil complete all as specified and directed.

Removing excavated soil n exc 50 m and depositing where directed at a level n exc 1.5m above the starting point complete all as specified and directed.

Material and labour for PCC type D2 1:4:8 using (40mm graded stone aggregate) as in foundation, filling and mass concrete, fixing of MS Pipes, etc. complete all as specified and directed.

Material and labour plain cement cement concrete type B1 1:2:4 using 20mm graded granite stone aggregate ) cast in situ in lintel up to 1.5M span ,cill and other similar bands plinth courses , parapets,coping,bed plates and the like including weathering, slightly rounded complete all as specifed directed

Supply and fix for framed work as in door or gates of angle or other section with gusset plates,rails braces etc. complete drilled for fixing of steel sheeting or other covering doors etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering , running rails and guides)_ and hanging also fastening and fixing ,Fe 410 -W (Gde-E-250) quality-A etc complete all as specified and directed.

Supply and fix mild steel, plain, black sheet in wall cladding , steel gates and similar work cut to size holes puncherd including round headed screws ,clout nails or rivets and fixed to wood or steel framing with plain 40mm lap joints with riveted or welded dseams including bending or turning up, mitred angles, etc.as required, thickness of sheet 1.60mm etc,complete all as sopecified and directed.

Supply and fix powder coated aluminium (minium thickness of powder coating 50 micron) work for doors frames,shutters,windows frames, shutters ventilators, sliding window frames shutters and partions (Fixed portion) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make confirming to IS:733 & IS :1285 fixing with dash fastners of required dia and size including necessary fillinng up the gaps at junctions at top bottom and sides with required EPDM rubber / neoprene gasket etc aluminium sections shell be smooth rust free straight mixture and joined mechanically wherever required including clieat angle aluminium snap beading for glazing / panelling CP brash/ stainless streel srews all complete as per architectural drawings complete all as specified and directed.

Supply and fix ,sheet glass 4.8 thickand glazing with oil putty / alu beads n.exc. 0.50sqm each pane (alu beads will be measured under alu door / windows) complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) area exc 1.5 Sqm and n.exc 4.00 Sqm each and offered as credited complete all as specified and directed.

All as per item No 59 above here in before but n exc 1.5 sqm complete all as specified and directed.

Taking down shutters exc 1.00 Sqm and n exc 2.0 Sqm complete all as specified and directed.

Supply and fix pressed steel frames 125 x 60 mm for doors with one or more rebates including necessary fixing lugs, Holdfasts,hinges,for door & wire mesh , lock strike plate, etc., complete all as specified and directed.

Supply and fix pressed steel frames 105 x 60 mm for doors with one or more rebates including necessary fixing lugs, Holdfasts,hinges lock strike plate, etc., complete complete all as specified and directed.

Material and labour Iind class hard wood 35mm double/ single flush door shutters solid core construction, with block board core & plywood face panels, commercial typeon both sides complete all as specified and directed.

Material and labour Second class hard wood 35mm thick, glazed and skeleton shutters open rebated and prepared to receive glass or gauge etc divided into squares with plain chamfered or rounded and rebated sash bars any numbers complete all as specified and directed.

Material and labour Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperature 1.40 mm and fixed withn wooden beading or with nuts and bolts to existing steel windows/wooden windows complete all as specified and directed.

Supply and fix Butt hinges 100mm medium weight cold rolled mild steel complete all as specified and directed.

Supply and fix Extruded aluminium alloy handles,150mm fabricated type anodized complete all as specified and directed.

Supply and Fix 100mm Butt hinges, extruded Aluminium alloy with galvanised mild steel hinge pin,anodised and fixed, type C-22 complete all as specified and directed.

Supply and fixing 300mm Mild steel sliding door bolts, plate type, stove enameled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts & nuts, four on bolts plate & two on staple plate & fixed complete all as specified and directed.

Material and labour for preparation of New or previously untreated wooden Surfaces of any description, not otherwise described, over 10cm width or grith complete all as specified and directed.

Supply and fix 150mm Floor door stopper of aluminum alloy body & tongue, anodized, with hard drawn steel spring, fixed in floor complete all as specified and directed.

Supply and fix Mild steel 300mm long ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed.

Material and labour for Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, supplying & fixing in opening complete all as specified and directed.

Material and labour for factory made solid panel pvc door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside complete all as specified and directed.

Supply and Fix 100mm Butt hinges, extruded Aluminium alloy with galvanised mild steel hinge pin,anodised and fixed, type C-22 complete all as specified and directed.

Supply and fix Alluminium, 150mm anodized, barrel tower bolts extruded section & fixedany position, complete all as specified and directed.

Supply and fix in repair stainless steel curtain rod 20 mm dia including mild steel CP brackets suitable for 19/20mm dia curtain rods including taking down of old curtain rod arrangements any type and making good of disturbed surface complete all as specified and as directed.

Supply and fix Windows of Double Rebate windows made of pre-painted steel (Base steel as per IS 513 of 0.58mm thick “D” Quality galvanized as per IS 277 with zinc of 120 GSM). Primer coated with epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with 5-7 microns thick alkyd backer. Section for outer frame should be of 72x55mm, centre mullion should be of 72x50mm, section for fixed glass beading should be of 12x12mm and section for shutter should be of 52 x 25mm. Outer frame & mullion sections to have rebate for glazed shutters, fly mesh and 20 mm provision for guard bars/ grills fly mesh shutter section should be of 20x40mm. The sections are to be cut to length mitre joined with corner bracket. Centre mullions to be fixed with mullion cap. Elixir or equivalent stay, handles 2nos of heavy duty stain less steel pivot hinges shall be provided per shutter. The windows should be paneled with 5 mm thick plain float glass and S.S. Mesh for fly mesh shutter (304 grade). Rubber Gaskets are provided all around the glass. The above frames should be fixed to the concrete/masonry wall by means of self expanding screws. Including 10mm square guard bars with 6” (152.4mm) pitch, complete for finished item of work including taking down existing steel windows and making good disturbed surfaces all as specified and directed.

Taking down 15mm bore steel tubing and connections in any position, Complete all as specified and directed.

Taking down 20mm bore steel tubing and connections in any position, Complete all as specified and directed.

Cutting chases, pinning in, making good to facings where required & pointing in cement mortar 1:3 for concealed water tubing, etc.& making good complete all as specified and directed.

Supplying and fix of 16mm CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors including provision of special fittings ( Unions, elbow, Tee, Male threaded brass adaptor, Female threaded brass adaptor, Tank adaptor etc), complete all as specified

Supplying and fix 20mm bore GI tubing medium grade with all fittings fixed to wall/ ceiling or in floor complete as specified and directed.

Supply and fix triple layer rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) of 500 ltrs capacity hoisted and fixed in position all as specified including dismantling old tank complete all as specified and directed.

Supply and fix triple layer rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) of 1000 ltrs capacity hoisted and fixed in position all as specified including dismantling old tank complete all as specified and directed.

Supply and fix 20 mm dia brass ball valve, high pressure with polythene float and fly-nut complete, screwed for iron pipe or brass ferrule fixed in repair complete all as specified and directed.

Supply and fix in repair 20 mm dia Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

Supply and fix for wash down water closet (pedestal pattern) complete white with plastic water closet seat, black, closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging device and flush pipe of polythelene of low or density or PVC 32mm dia for low level flushing cistern incl pedestal pan and P/S trap, and connection to drain (or outgoing pipe) complete. Make: Cat No 20011 of Hindware/Cat No 4017 of Prayag/ Cat.No: S1053102 of CERA or equivalent make as approved by GE.

Supply and fix PVC valveless syphonic action type flushing cistern 10 lit capacity low level white with inlet, ball valve, float and handle including brackets and 32mm PVC flush pipe complete all as specified and directed.

S&F for vitreous china wash basin, white, flat back size 550 x 400mm including 01 Nos cast copper alloy 15mm CP fancy type pillar tap, 01 Nos 32mm waste coupling , one pair of MS bracket, cutting for and pinning in ends of brackets complete all as specified and directed.

Supply and fix in repair 125mm size brass chromium plated shower rose with or without swivel joints including fixing to steel pipe or union fixed complete all as specified and directed.

Supply and fix in repairs 15 mm dia fancy type stop valves/ angle cock chromium plated screwed down, high pressure, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed. Make: Cat No F360006 of Hindware/ Cat No 8510 of Prayag / Cat No CQT-CHR-23059 of Jaquar or equivalent make as approved by GE.

Supply and fix in repairs 15 mm dia fancy type conceled stop valves/ angle cock chromium plated screwed down, high pressure, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed. Make: Cat No PIS-18 of Prayag/Cat No: F200007 of Hindware / Cat No : T5012A1 of Parryware or equivalent make as approved by GE.

Supply and fix in repair 15mm bore Bib taps, chromium plated cast copper alloy but fancy type, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed. Make: Cat No F440003 of Hindware/Cat No PIS-08 of Prayag /Cat No CON-CHR-047KN of Jaquar or equivalent make as approved by GE.

Supply and fix in repair two way bib tap/cock 15mm bore with wall flange, chromium plated, fancy type complete all as specified and directed. Make: Cat No COP-041PM of Jaqur/Cat No 8512 of Prayag / Cat No F740004CP Of Hindware or equivalent make as approved by GE.

Supply and fix in repair Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified. complete all as specified and directed. Make: Cat No F100110 Of Hindware/Cat No BEA-40 of Prayag/ Cat No E8384A1 of Parryware or equivalent make as approved by GE.

Supply and fix in repairs PVC connection 15mm dia, 45 Cms long with brass ferrules on both ends fixed complete all as specified and directed.

Supply and fix brass chromium plated tubular towel rail 20 mm dia ‘D’ type 60 cm long between flanges of brass chromium plated complete all as specified and directed.

S&F stainless steel Kitchen sinks with drainage board made of stainless steel 1.0mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm including necessary PVC outlet pipe and coupling complete all as specified and directed.

Supply and fix in repair stainless steel plate rack 31" X 36" X 10" made up of 1mm thick sheet (Non magnetic) complete all as specified and directed.

Supply and fix in repair brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and directed. Make: Cat No CQT-CHR-23273UPR of Jaquar/ Cat No 8575 0f Prayag/ Cat No 2-in-1 T1354A1/ G5816A1 of Parryware / Cat No: F570020 of Hindware or equivalent make as approved by GE.

Supply and fix PTMT Shelf of weight not less than 300 gms with soap dish (tray) fixed with and including Chromium plated brass screws and wooden / plastic cleats etc., complete all as specified and as directed.

Supply and fix PVC( SWR ) pipes 110mm dia single socketed , in any length with rubber ring joints as rainwater, soil waste and vent pipe (with all fittings) fixed to wall incl taking down existing pipe complete all as specified and directed.

Supply and fix PVC (SWR) pipes 110mm dia single socketed, in any length with rubber ring joints, laid in trenches or in floors incl taking down existing pipe complete all as specified and directed.

Supply and fix PVC( SWR ) pipes 75mm dia single socketed , in any length with rubber ring joints as rainwater, soil waste and vent pipe (with all fittings) fixed to walls incl taking down complete all as specified and directed.

Supply and fix PVC( SWR ) pipes 75mm dia single socketed , in any length with rubber ring joints as rainwater, soil waste and vent pipe (with all fittings) laid in trenches incl taking down complete all as specified and directed.

Supply and fix in repair PVC (SWR) bends any radius 110mm bore complete all specified and directed.

Supply and fix in repair PVC (SWR) bends with access door any radius 110mm bore complete all specified and directed.

Supply and fix PVC (SWR) junction single (single T) equal or unequal with access door of bore 110mm complete all specified and directed.

Supply and fix PVC(SWR) vent cowl 110mm bore complete all specified and directed.

Supply and fix PVC (SWR) bends any radious 75 mm dia complete all specified and directed.

Supply and fix PVC (SWR) bends with access door any radious 75 mm dia complete all specified and directed.

Supply and fix PVC (SWR) junction single (single T) equal or unequal of bore 75mm complete all specified and directed.

Supply and fix PVC (SWR) junction single (single T) equal or unequal with access door of bore 75mm complete all specified and directed.

Supply and fix in repair PVC (SWR) floor trap 75mm dia outlet, plain with grating including jointing with solvent cement complete all specified and directed.

Supply and fix for PVC waste pipe for Sink/WHB with fitting etc 38 mm dia. 60mm long complete all specified and directed.

Dismantling of boarding, any description fixed in any position with nails complete all as specified and directed.

Material and labour for providing and fixing false ceiling 12mm thick False ceiling tiles of size 595 x 595 mm of approved texture, design and patterns having moisture contents less than 2% humidity resistance of 99% NRCO.50 to .75 as pe IS8225:1987, Noncombustible as per BS 476 (Part 4)-1970 and light reflectance of 85% (Minimum) to be laid in true horizontal level suspended on interlocking metal T Grid of hot dipped galvanized iron section of 0.33 mm thick ( galvanised @ 120 gms per sqm including both sides ) comprising of main T runners of size 15 x 32 mm of length 3000mm, cross -T of size 15 x 32 mm of length 600mm to form grid module of size 600 x 600mm, suspened from ceiling using galvaized mild steel items ( galvanizing @ 80 grams per sqm) i..e 50mm long, 8mm outer diameter M-6 dash fastener 6mm dia fully threaded hanger rod upto 1000mm length and L-swhape level adjuster of size 85x25 x 2mm galvanised iron permieter wall angle of size 24 x 24 x 0.40mm of length 3000mm to be fixed on periphery wall/ partition with the help of plastic rawl plugs at 450 mm ceneter to centre and 50mm long dry wall wood screws. The kwork shall be carried out as per specifications, drawing and as per directions of the Engineer-in-charge.

Material and labour for 2nd Class hard wood plain fillets, square or triangular in section, clean swan, secured with nails or brads, croos sectional area exc 13 Sqcm but not exc 25 Sqcm complete all as specified and directed.

Supply and fix of 18/19mm thick prelaminated particle board interior grade sprelaminated one side with decorative choice lamination and other side balancing white lamination fixed with nails to timber frame work in repairs

Extra over rates of block board or veneered particle board of (18/19mm ) for external teak wood lipping 6mm thick fixed with nails.

Supply and fix Continuous (piano) hinges,mild steel, bright finish or electro galvanised, Width of flaps (when open) in 30 mm etc complete all as specified and directed.

Supply and fix 75mm extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

Supply and fix brass 2-levers locks for cupboard, grade I of size 50mm complete all as specified and directed.

Supply and fix fanlight magnetic catch with 14mm catch cast brass and fixed to cupboard shutters all as specified and as directed

Preparation of old painted steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying one coat of synthetic enamel paint complete all as specified and directed.

Dismantling Stone slabs and tiles of any description or thickness and Material and labour for 60mm thick M-35 grade factory made rubber moulded precast concrete interlocking paver block in grey cement with pigments and of approved size and shape and conforming to IS 15658-2006, with and including 50mm thk sand bedding layer laid to true line, level watered and mechanically compacted etc complete all as directed.

Material and labour Preparation of old painted wooden surfaces of any description over 10 cms width or girth not otherwise described and applying one coat of synthetic enamel paint .

Material and labour chequered cement concrete tiles 30cmx30cmx25mm thick with grey cement and pigment, machine pressed, set jointed and pointed in neat cement slurry in floors including 15 mm thick screed bedding layer in CM 1:6 complete all as specified and directed.

Material and labour for Hard core of guage n.exc 63 mm, deposited, spread and levelled in layers n.exc 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

Material and labour for 100 mm thick cement concrete type B-1, 1:2:4 (using 20mm graded aggregate) surface finished even and smooth without using extra cement complete all as specified and directed.

Material and labour for forming 12 mm thick expansion joints for 40 mm concrete slab thickness filled with preformed bituminous filler and top 30 mm primed and sealed with sealing compound grade A.

Excavating post holes or similar works, each not exceeding 0.5 Cum getting out in hard/dense soil, returning and filling in and rammimg earth or broken rubble mixed with earth around in layers not exceeding 25cm, watering and removing surplus soil complete all as specified and directed.

Material and labour for providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required completeall as specified and as directed.

INTERNAL ELECTRIC SUPPLY

Material and labour for point wiring complete all as specified with 1100 Volts grade 1.5 Sqmm PVC insulated FR-LSH unsheathed cable with multistranded copper conductor conforming to IS:694:1990 with ISI marking in and including PVC rigid conduit medium grade of size minimum 20 mm with all accessories concealed in wall / ceiling including continous earth wire 1.5 Sqmm PVC insulated FR-LSH unsheathed 1100 Volts multistranded copper conductor connected to common earth and earth dolly including modular metal flush boxes concealed in walls and modular white plate covers with frame for mounting of modular switches/sockets/fan regulators etc complete all as specified for the following:-

One light / fan point controlled by one switch.

One three pin switch socket 6 Amps outlet on independent board.

One three pin switch socket 6 Amps outlet on same board

One light point controlled by two nos of two way

One bell point controlled by one bell push.

All as per item No 138 here in before but with cable 4 sqmm multi stranded copper FR-LSH wire , 1100 Volts grade, unsheathed for one 3 pin socket out let 15 amps on independent board including continuous earth wire PVC insulated 4 sqmm copper stranded conductor FR-LSH, 1100 Volts grade, connecting to common earth and earth dolly complete all as specified and directed.

Supply and fix Modular switch 1 way 6A , 1-module complete all as specified and directed.

Supply and fix Modular switch 1 way 16A with indicator, 1-module all as specified and directed.

Supply and fix Modular socket, shuttered type, 6A - 3 pin 2 -module all as specified and as directed.

Supply and fix Modular socket, shuttered type, 6/16A - combined 2-module complete all as specified and as directed.

Supply and fix Modular switch 2 way 6A,1 module complete all as specified and as directed.

Supply and fix Modular Bell push 6A 1 module complete all as specified and as directed.

Supply and fix Bell, Ding Dong AC. 230 volts, single pole complete all as specified and as directed.

Supply and fix power module 240V, 20A complete with 4 module metal flush box, cover plate, Starter, Plug & Socket complete all as specified and as directed.

Supply and fix 3 pin, 6 A, 250 V ceiling rose conforming to IS 371: 1999 and having terminal capacity 3 X 1.5 mm² with IK 04 and IP 20 protection complete all as specified in IS 732: 2019 and directed.

Supply and fix single pole & neutral, double door, metallic distribution board 12 ways conforming to IEC 61439-3, suitable for flush / surface mounting with provision for DP RCCB / RCBO / Isolator / MCB as incomer and SP MCBs as outgoing, reversible metal door, 100 A copper busbar, fully shrouded neutral bar, earth bar, wire set & cable ties for cable management, pre fitted masking sheet, etc. having IK 09 & IP 43 protection complete all as specified in IS 732: 2019 and directed.

Supply and Fix factory made prewired TPN 4 ways distribution board in sheet steel enclosure vertical double door with suitable rated bus bar 415 volts suitable for housing TPN MCCB as incoming and SP MCBs as outgoing complete all as specified and directed.

Supply and fix MCB ('C' curve) 6- 32 A, 230 V, 50 Hz, SP for conforming to IS/IEC 60898-1-2002, having breaking capacity Icn = 10 kA, sliding bottom clamp, colour coded on/off indication on dolly, bi-connect IP 20 protected lower terminals and sliding shutters, etc. with the following rating complete all as specified in IS 732: 2019 and directed.

Supply and fix RCBOs for earth leakage, overload & short- circuit protection 6-32 A, 230 V, 50 Hz, 2P, 100 mA rating complete all as specified in IS 12640-1 (2008) and directed.

Supply and fix RCBOs for earth leakage, overload & short- circuit protection 32 A, 415 V, 50 Hz, 4P, 30 mA rating complete all as specified in IS 12640-1 (2008) and directed.

Supply and fix MCCB, 415 V, 16KA, 4 Pole, 63 Amp complete all as specified and as directed.

Material and labour for submain wiring using 3 runs of 4 Sq mm 1100 V grade single core FR-LSH flexible cable conforming to IS 694: 2010, having multi-drawn thin strands of electrolytic copper conductors and insulation for phase, neutral and earth continuity conductor connecting to earth dolly, colour-coded as per IS 11353: 1985, drawn in medium grade PVC recessed conduits, conforming to IS 9537 (Part- 3): 1983, of size not less than 25 mm NB, including making good of disturbed surfaces of wall / ceiling / floor all complete as specified in IS 732: 2019 and directed.

All as per Item No.155 above but 6 Sq mm wiring cable complete all as specified and as directed.

Material and labour for taking down ceiling fan, seialing cable end, dismantling blades and depositing fan and blades to store and including painting of ceiling fans complete, with synthetic enamel paint by spraying including filling cavities with filler, onecoat after cleaning all dust and refixing of ceiling fan & connecting up including provision of cable from ceiling rose or connector to fan etc. complete all as specified and directed.

Supply and fix exhaust fan made of sturdy Engineering plastic body complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250mm sweep for Toilet of Md Accn complete including making suitable size hole in wall as specified and directed.

Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300 mm sweep with, blades, and frame and louvers including making suitable size hole in wall complete all as specified and directed.

Supply and fix Wall mounting fan 400 mm sweep, 230V, 50Hz, 3 speed white in colour, 3 blades complete all as specified and directed.

Fixing only in repairs LED batten 20W complete all as specified and directed.

Supply and fix Electronic type fan regulator stepped 2 module type, suitable for BLDC fan to work on 230 volts complete all as specified and directed.

Material and labour for GI tubing medium grade 40 mm dia concealed on both side walls for hanging ceiling fan and provisioning of hook

Supply and fix TV CO-Axial socket outlet fixed to wall on hylem sheet complete all as specified and directed.

Supply and fix Rigid non-metallic PVC conduit of dia 20 mm exclusive of boxes (junction/terminal) but inclusive of all tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc complete all as specified and directed.

Supply and fix 20 W surface / wall mounted LED batten having PC diffuser, luminous efficacy of minimum 100 lumen/W, CRI > 80, PF > 0.9, CCT 6500K, independent isolated SMPS based constant current electronic LED driver with THD < 20%, surge voltage protection and other safety tests as per IS 15885 (Part-2/Sec-13): 2012, polycarbonate diffuser, housed in powder coated white extruded aluminium channel housing. white coloured ABS end caps, IP 20 protection, input voltage range 140- 270 V, input frequency 50- 60 Hz, including electrical connection with 3 core flexible Cu conductor cable of appropriate size from ceiling rose to the fixture complete all as specified and directed. Make: CAT No. STOUT MINI 1200 BS20WLED865SPCWH of Havells or equivalent in Wipro / Philips / Crompton / Bajaj.

Supply and fix Wall bracket fancy type single head light fitting with B22 holder (OR Accn) complete all as specified and directed.

Supply and fix Wall bracket fancy type double head light fitting with B22 holder (Offcr Accn) complete all as specified and directed.

Supply and fix adjustable Bed side lamp LED 3W, 3000K, metal body in black colour with Gooseneck arm complete all as specified and directed.

Supply and fix LED10W mirror light, wall mounting surface type, not less than 900 Lumen, 1 feet long complete all as specified and directed.

Supply and fix LED light fitting 1x9W/1X10W bulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed. Make-CAT No. RUGBYGENXFTS10WLED865SSYMBOPC of Havells or equivalent in Wipro / Philips / Crompton / Bajaj.

Supply and fix Lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings suitable for B22 type LED bulb complete all as specified and directed.

Supply and fix LED Bulb 12 W B22, BEE star rated with minimum 3 star rating complete all as specified and directed.

Supply and fix 35 W security light having high efficiency long life LED module with SMD LED package mounted on MCPCB with high LED efficacy of ≥ 110 lumen/Watt, integral SMPS based constant current electronic LED driver with THD < 20%, surge voltage protection and other safety tests as per IS: 15885 (Part-2/Sec-13): 2012, IP 66 protection, high effiency polycarbonate cover with integrated lens housed in pressure die-cast aluminium alloy heat sink for effective thermal management, sturdiness, excellent corrosion resistance, separate optical and control gear compartment & top opening for easy maintenance, suitable for side entry, wall mounting with bracket arm OD 35 mm to 42 mm including necessary electrical connection to the fixture with 3 core flexible Cu conductor cable of appropriate size and 1.5 m long bracket, having 40 mm diameter light grade GI pipe, including GI clamps, nuts, bolts & washers with two coats of synthetic enemal paint over a coat of red oxide primer complete in all respect as specified and directed. Make - CAT No. ENDURASUNDOWN35WLED765PASYBOPC of Havells/or equivalent in Wipro / Philips / Crompton / Bajaj.

Material and Labour for Earthing complete with galvanized steel earth plate electrode 60cm x 60cm x 6mm thick, buried directly in ground (earth pit not less than 2.25m deep below normal ground level) with top edge of plate not less' than 1.5meters below normal ground level, earth plate connected to galvanized earth lead wire 4.00 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 of MES SSR-2009 (part I Specifications) connected to earth test point all as specified or indicated including testing on completion, including necessary excavation and earth work in any type of soil and adequate quantity of common salt & charcoal for alternate layer around the earth plate, including PCC (1:2:4) pit and 10mm thick C.I. cover with arrangement of hinge to 40x40x6mm C.I. angle iron frame, including 20mm dia G.I. pipe medium grade for watering purpose with the arrangement of funel and wire mess, including GI pipe of 15mm dia medium grade for earth lead protection complete all as specified and as directed. Note :- The rate is deemed to be inclusive of the cost of earth work, excavation on any type soil and removal of surplus soil to a distance of 50 Mtrs, PCC 1:2:4 type B1 for earth pit cover 6 Nos 6 mm dia CTD bar on both direction, earth lead protection GI pipe medium grade with suitable size from earth plate electrode to main switch, GI wire length up to 7.50M will be measured as one unit)

Material and labour for removing existing Light fitting, DB with MCBs etc, complete all as specified and directed.

Material and labour for taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc. complete all as specified and directed.

Supply and fix 90 cm 1600 m³/hr BLDC Filterless Thermal Autoclean Kitchen Chimney, Slant (Hood KOPPA HSR 90, Heat Sensor/Aeration technology/Auto On/Off| Touch & Gesture Control,Black) including chimney bracket,aluminium exhaust pipe and making suitable hole for exhaust pipe, finishing the disturbed surface with cement mortar and provide grill outside the hole complete all as specified and directed.

Cutting chases, pinning in making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings steps, cills, sunshades,shelves, lintels,etc, and cutting chases for concealed water tubing or concealed conduit wiring etc and making good cutting not exc 10 cm grith complete all as specified and directed.

HOT WATER SUPPLY

Supply and fix electric operated storage water heater (Geyser) capacity 25 ltrs capacity vertical type 2KW suitable for operation on AC 230 volts complete all as specified

Material and labour for CPVC pipe SDR-11& plain CPVC SDR-11 fitting for hot & cold water supply of 15mm dia including all random fittings fixed complete to walls, ceilings or in floors etc & testing after laying up to entire satisfaction of engr-in charge all as specified & as directed by engr-in-charge.

Supply and fix Stop valves, chromium plated screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe of size 15 mm complete all as specified and directed.

Supply and fix Bib tap chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed all as pipe of size 15mm specified & as directed.

EXTERNAL WATER SUPPLY

Supply and fix galvanized steel water tubing medium grade of 50mm bore complete with all fittings such as bends elbows, tees, short pieces, connectors, back nuts, diminishing pieces, caps and pigs, unions including taking up or down existing steel tubing with fittings all as specified and directed.

All as per item no. 184 above but 25 mm bore complete all as specified and directed.

Supply and fix Cast Iron globe valve 50 mm bore, with stainless Steel spindel and cast iron body with clamps and check nuts, operating hand wheel, both end flange and drilled conforming to IS 148 46-2000 type PN 1.6, ISI marked including jointing materail such as rubber insertion gas kit with suitable bolts, nuts and washers etc,complete all as specified and directed.

Supply and fix stop valve cast copper alloy screwed down high pressure with crutch & butterfly handle, 25mm bore

Cutting/Boring on the existing CI/GI pipe line 50mm dia (in position) for insertion of new galvanised Tee 50 x 25 mm for branch connection incl necessary jointing material complete all as specified and as directed.

Supply and fix for construction of Brick Masonry valve chamber 600x600x600mm inner dimensions, With PCC 1:4:8 foundation 150 mm thick, brick work built in CM 1:6, PCC 1:3:6 copping 50 mm thick, plastering 15 mm thick in Cm 1:6 to all internal and exposed surfaces including excavation earthwork in hard/dense soil, MS sheet cover 4 mm thick welded to frame made out of 40x40x3mm as cover fix with hinges welded to frame 50x50x6mm with locking arrangement in PCC and painting to MS cover with two coats of synthetic enamel paint over one coat of red oxide primer etc complete all as specified and directed.

EXTERNAL ELECTRIC SUPPLY

Supply, laying, connecting and testing XLPE cable insulated , screened, PVC bedded, galvanized steel strip or wire armoured, electric power cable (heavy duty) 1100 volts grade with stranded aluminium conductor of following sizes in trenches / through GI pipe / fixed along with pole structure etc with all fixing & connecting accessories, terminations etc complete all as specified and directed by Engr-in-Charge (Note: Excavation & earth work shall be measured and paid separately)

95 Sqmm x 3.5 Core

50 Sqmm x 3.5 Core

35 Sqmm x 3.5 Core

25 Sqmm x 4 Core

16 Sqmm x 4 Core

Supply and spread sand in trenches as sand cushioning to under ground cable for protection with fine river sand and provide required cover after punning down complete all as specified and directed.(Note: Only Punned thickness after punning will be measured and paid)

Supply and laying burnt bricks sub class B of old size laid dry in trenches for cable protection all as specified

Supply, install, testing and commissioning of new Out door LT feeder Pillar Box, factory fabricated, CPRI tested , cubicle type, 3.15 mm thick CRCA sheet vermin proof with 3 phase and neutral Aluminium bus bar of current capacity 200A of suitable size, phase and neutral colour coded with heat shrinkable PVC sleeves, with necessary supports, angle iron frame work and stand, locking arrangements and painting with one coat of red oxide primer and two coats of powder coated paint, suitable size of panel control copper wiring, accessories fitted on suitable insulator all housed in suitable bus bar chamber and fixing of digital Voltmeter and pilot indication lamps RYB set of 03 nos along with provision of necessary cable entry/exit boxes for all incoming and out going cables with suitable cable glands etc including PCC foundation complete all as specified and directed and consisting of one MCCB 63A/100A, 4P, 16 kA.

Material and labour for Earthing of machinery/equipment Installed at power house/substation complete using galvanized steel earth plate electrode 60cm x 60cm x 6mm thick buried directly in ground (earth pit not less than 2.25 mtrs deep below ground level) with top edge of the earth plate at a depth of not less than 1.5 mtr below ground level connected to galvanized iron strip 32x 6 mm as earthing lead by means of bolts, nuts and washers made out of GI/steel earth strip protected by GI pipe 40 mm dia medium grade and connecting to main panel board/switch board/control board all as shown in electrical plate No 3 of SSR Pt I incl PCC chambers in 1:2:4 and RCC cover slab with 8mm dia MS bars reinforced at 10 cm center to center both ways including 20mm dia GI pipe medium grade for watering purpose with the arrangement of funnel and wiremesh including earth work like excavation, returning filling back disposal etc complete.

Note :- The rate is deemed to be inclusive of the cost of earth work, excavation on any type soil and removal of surplus soil to a distance of 50 Mtrs, PCC 1:2:4 type B1 for earth pit cover 6 Nos 6 mm dia CTD bar on both direction, earth lead protection GI pipe medium grade with suitable size from earth plate electrode to main switch, GI strip length up to 7.50M will be measured as one unit)