REPAIR TO CERTAIN ROAD NEAR BAHADUR BRIDGE, NAND SINGH CHOWK AND OTHER AREA AND ROAD FURNITURE UNDER AOR OF GE(S) BATHINDA AT BATHINDA MIL STN

Amount

Material and labour for preparing black top surface by brushing with wire brush for removing caked mud etc. sweeping with brooms and finally fanning the cleaned surface with air pressure through air jet using air compressor to remove all the loose dirt etc. including removing the mud etc. to a distance minimum 1.5 mtrs from edge of road and applying evenly a tack coat of bituminous primer using paving bitumen (VG-10) @ 5Kg per X sqm of road surface by sprayer operated hot pressure mechanism including supplying, laying, spreading 25 mm consolidated thickness of semi dense asphaltic concrete grading 2, maximum aggregate size 9.5 mm, with job mix formula using paving bitumen (VG-30) @ 5.0% binder content by weight of total mix using mechanical paver for levelling within the specified tolerance as specified in SSR Part-I, rolled and consolidated to required camber and gradient with power roller for uniform smooth surface etc. complete all as specified and directed by Engineer-in-Charge. Note :- (i) The job mix formula shall be approved by GE. (ii) 5.0% binder content has been specified for quoting purpose of bid. If the quantity of the bitumen exceeds the 5.0% as mentioned above, no plus price adjustment shall be made. If the quantity of bitumen required as per job mix formula works out less than 5.0%, the recovery of the supply only bitumen shall be effected @ Rs. 50/- per Kg. The cost of transportation of material and testing charges shall be borne by the contractor. (iii) Contractor shall intimate the planned date of incorporation of mix in advance to GE. Premix will be approved in writing by Rep of Accepting Officer at plant site before incorporation of the same in the work

Repairs to potholes not exceeding 1 Sqm each including sweeping free from dust and mud, or water, scoring sunken surfaces in roads, paths etc. cutting around edges to at least 25 mm in depth and applying tack coat @ 5 kg per 10 Sqm of paving bitumen (VG-10), putting in premixed bituminous macadam, well rammed and sealed with binder 9.8 kg per 10 Sqm of paving bitumen (VG-30), blinded with 0.09 cum of stone chippings, 6.3 mm size and again well rammed, depth of pot holes exceeding 30mm. Note as per MORTH Specification: (i) Loose material and standing water shall be brushed from the area to be repaired. (ii) Potholes shall be cut to vertical sides and deepened to reach sound material . (iii) Fill the patch with the granular mix in layers of about 75mm at a time. Each layer shall be compacted with hand rammers or with small vibratory compactors. The patch shall be compacted to the correct shape. (iv)100% quantity of Pot holes shall be marked and checked by Engineer-in-charge before commencement of work and shall also be entered in MB with reference to permanent objects before starting carpeting work. (v) Rate quoted by contractor shall deemed to be including of supply of premixed macadam binder and chippings

Supplying, laying and spreading upto 75mm thick or less ( consolidated thickness) premix bituminous macadam (BM) filling in depression grade 2 (using 19.2 mm graded stone aggregate) in single layer with using mechanical paver using paving bitumen (VG-30) @ 3.4 % by weight of total mix with job mix formula, laid / rolled and compacted/ consolidated to required camber and gradient with 8 to 10 tonne power roller to a uniform smooth surface etc. complete all as specified and directed by Engineer-in-Charge. Note :- (i) The job mix formula shall be approved by GE. (ii) 3.4% binder content has been specified for quoting purpose of bid. If the quantity of the bitumen exceeds the 3.4% as mentioned above, no plus price adjustment shall be made. If the quantity of bitumen required as per job mix formula works out less than 3.4%, the recovery of the supply only bitumen shall be effected @ Rs. 50/- per Kg. The cost of transportation of material and testing charges shall be borne by the contractor. (iii) Contractor shall intimate the planned date of incorporation of mix in advance to GE. Premix will be approved in writing by Rep of Accepting Officer at plant site before incorporation of the same in the work

M&L for painting lines, dashes, arrows, letters, marking etc of thermoplastic paint applied Min 6 Kgs /Sqm on new surfaces or previously treated road surfaces with hot applied reflective thermoplastic road marking paint (White / Golden yellow) conforming to MORT&H (clause 803.4) all as specified with 8% Type 1 glass beads using special applicator machine with heating arrangement upto 160˚ C including cleaning and drying the existing road surfaces to ensure dust, oil, grease and moisture free surfaces before applying the paint complete all as specified and directed. Make : Automark or equivalent make given in Appx 'B'. Note: Thermoplastic paint should be applied Minimum 6Kg/Sqm

S&F in repairs two way (dual direction) reflective road studs (Cat eye) of ABS body of dimensions 100mm x 100mm x 20 mm with red / yellow /amber reflective panels and fixing the same on road surface by applying approximately 100 gm Epoxy mixture and placing the cat eye without applying excessive pressure and additional fixed with 8 mm dia and 120 mm long zinc plated steel nail at the centre of cat eye complete all as specified and directed.(Model No DA-978 of Dark eye or equivalent model of 3M/Greenlite)

Supply and fix solar cat eye aluminum alloy shall (100% water proofing design according to 65) of size 125mm x 125mm x 25mm (shank 65mm) of high efficiency Mono rystafie solar panel 2.4V/0.3 watt one NI-ed rechargeable battery (1.2/1600MA) consisting of super bright LED with 10,000 to 18,000 med completed as peremanufactures instructions etc. all as specified

S&F dual direction delineator on powder coated steel pipe of 900 to 1000 mm height with two Nos high performance 100mm dia reflectors and two rectangular reflectors of 70mm x 23mm are fixed on both sides of guide post . Reflector are positioned at the best eye guiding level and fixing in cement concrete (1:2:4) type B1 using 20mm graded stone aggregate with size of block 300mm x 300mm x 350mm deep including excavation and earth work in any strata complete all as directed by Engineer-in-charge. Note: - The rate of PCC & earth work is included in the unit quoted rate. (Cat part No DA-74 of make Dark Eye or equivalent make of 3M/Greenlite)

S&F solar delineator 600 mm long made of ABS material dual directional rectangular, fitted with 4 ultra bright flashing LEDs and mounted on MS pipe 50mm dia powder coated (shade as approved by GE) anti rust and anti theft steel nuts 125 x 100mm size and fixing in cement concrete (1:2:4) type B1 using 20mm graded stone aggregate with size of block 300mmx300mmx350mm deep including excavation and earth work in any strata complete all as directed by Engineer-in-charge. Note: - The rate of PCC & earth work is included in the unit quoted rate.(Cat part No DA-112 of make Dark eye or equivalent make of 3M/ Greenlite)

S & F to Road Speed breaker having high intensitie cube corner ferlector, high impact resistent ABS plactic body of size 250mm x 345mm x 50mm (height) fixed with bolts and adhesive complete all as specified and directed by Eng-in-Charge. (Cat part No GPL-07-06 of green light or equivalent Make of 3M/Dark eye.

S & F for Convex Mirror of 800mm dia made from long life poly carbonate with strong impact resistant and shattler proof fitted with a sun shield or protective hood of colour as approved by GE and 75 mm dia MS pipe duly painted of approved colour of suitable length as directed including fixing in cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate with size of block 450x 450x600mm deep including excavation and earthwork complete all as specified and directed by Eng-in-Charge

M & L for frame work for sign board or any other structure/ position made out of stainless steel chromium plated round/ square pipes 304 grade, cut to shape including bending, welding, drilling, gusset plates and riveting complete all as specified and directed by Engineer-in-Charge. Note:- Rate is including for necessary accessories required at site including leg/ post embedded in PCC block of size 40cm x 40cm x 50 cm in cement concrete (1:2:4) type B-1 using 20mm graded stone aggregate including necessary excavation and earth work complete all as specified and directed by Eng-in-Charge.

Supply and fixing in new sign board aluminium composite panel sheet 3mm thick used for informatory/ cautionary/ warning sign board for road safety features etc, fitted / framed in steel pipe frame including fixing arrangements complete all as specified and directed by Eng-in-Charge. Note:- Steel frame, legs, letter writing shall be measured and paid separately under appropriate item of BOQ.

Material and labour for writing letter or figures arrows, Bldgs/ colony layout computer cut (Block Roman), italic or Indian) width 25mm and height as directed by Eng-in-Charge, made out of ertry reflective luminious tape as per IRC standard, in approved colour, pasted firmly without appearance/ sign of bubbles on aluminium sheet complete all as specified and directed by Eng-in-Charge.

M & L for preparation of old or previously treated concrete surfaces of any description not otherwise described over 10cm width or girth and applying one coat of acrylic water based marking paint complete all as specified.

S & F dual directional rumble strip of high impact resistant ABS plastic body of size 150mm wide X 25-30mm height having 2 micro prismatic polycarbonate reflectors to one side (04 nos on both side) fixed with bolts and adhesive complete all as specified and directed by Eng-in-Charge. Cat part GPL-07-03 of Greenlite or equivalent Make of 3M/Dark eye.

S & F reflective tape 50mm wide of Red & Yellow colour fixed to steel/concrete surfaces complete all as specified and directed.

Dismantling stone slabs and tiles (laid dry or laid dry and pointed ) of any description or thickness in floors, aprons etc. complete all as specified and directed

M & L for Plain cemtent concrete (1:4:8) type D-2 using 40mm graded stone aggregate as in sub base complete finished even & rough complete all as specified and directed.

M & L for Sand cushion (25mm thick) filling under floors or in foundation including watering and consoilsated all as specified and directed.

Material & Labour for factory made Machine pressed precast concrete interlocking paver block with grey cement and pigment any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade complete all as specified and directed.

All as per item No -20 but except tiles

M & L factory made precast cement concrete (1:2:4) type B-1 using 20mm graded stone aggregate as in kerb stone, quion block, apex stones etc, set in cement mortar (1:4) including formwork weathering, slightly rounded or chamfered angles and throating including taking down old kerb stone all as specified and directed. Note:- Excavation and earthwork included in the rate quoted. Nothing extra shall be paid on this account.

Note:- (i) The contract sum shall be calculated by deducting the amount shown in Credit Schedule attached to this tender from total amount of Schedule 'A'/BOQ (ii) Page No. 133 of tender documents will be uploaded by the bidders duly filled alongwith cost of tender documents and application otherwise the bid will be rejected.

AP BUILDERS

JB Infrastructure

M/s Azure Infrastructure Construction Co.

FAIR DEAL CONSTRUCTION CO