ADDN/ALTN TO CERTAIN JCOS/OR MD ACCN, PROVISION OF 01 X SOAKAGE PIT AND CONSTRUCTION OF DRAINAGE NEAR BLDG NO. P-483 (OR LINE) OF 5271 ASC BN (MT) AND PROVISION OF DEFFICIENT STAINLESS STEEL SINK AS PER NEW SOA FOR CERTAIN OLD OR/JCOS MD ACCN AT BD B

Taking down cement plaster on bricks or stone wall/ decayed surfaces of concrete from roof projection or RCC Chajjas etc. including racking out joints, hacking for key, scrubbing down with water, etc including removing the waste out of defence land complete all as specified and as directed.

M&L rendering 10 mm thick on fair faces of brick work or concrete surfaces in CM 1:6 finished even and smooth without using extra cement complete all as specified and as directed.

M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 and finished even and smooth without using extra cement complete all as specified and as directed.

M&L Rendering 15 mm thick on fair faces of brick/concrete surfaces in cement plaster 1:4 finished even and smooth without using extra cement, using water proofing compound mix as per manufacturer detail, complete all as specified and as directed. (WPC measured and paid seperately)

M&L Rendering 5 mm thick on concrete surfaces in CM 1:3 finished on even and smooth without using extra cement as in ceiling, Chajja etc complete all as specified and as directed

Material & Labour for RCC chajja/fascia/parapet repair by using following steps :- (a) Removal of existing concrete along with loose damaged and cracked concrete/cover concrete from chajjas etc, exposing corroded steel reinforcements upto a depth of 10mm minimum behind the reinforcement by chipping/hacking with chisel and hammer or by mechanical means like chisel hammer, pneumatic chippers including high pressure water jetting to chipped concrete and reinforcement all as directed by Engineer-in-charge. Hard concrete shall not be removed. However if the rebar is corroded, concrete around it shall be removed. (b) Cleaning the surface of reinforcement bars from dust by using wire brushes and dry cloth and applying FOSROC Rebakleens RR- Rust Remover or equivalent using small brush and allow to react it for 16-24 hrs. (c) Providing and applying two coats of Fosroc Nitozinc Primer - two component, zinc rich epoxy, anti-corrosive protective coating or equivalent by brushes to the exposed and cleaned rebars with an interval of 45minutes to 1 hour @ 40microns DFT / coat and allowed to completely dry for 24 hours complete all as specified and as directed

Supply only Integral water proofing compound liquid complete all as specified and as directed

Taking down chowkats or frames n. exc. 1.5 sqm each but with shutter without taking off shutters from the frame.

Taking down chowkats or frames exc. 1.5 sqm & n.exc. 4 sqm each but with shutter without taking off shutters from the frame.

S&F pressed steel frame for door with one or more rebates including necessary lugs, fixing lugs hinges, lock strike plate etc. of size 125mm x 60 mm and made of 1.25mm thick MS sheet, complete all as specified and directed including necessary welding complete and including medium weight 03 Nos of MS butt hinges of size 75mm / 100mm / 125mm and 01 No 50mm Size of medium weight MS butt hinge complete all as specified and directed.

S&F Pressed steel frame for door with one or more rebates including necessary lugs, fixing lugs hinges, lock strike plate etc. of size 105mm x 60 mm and made of 1.25mm thick MS sheet, complete all as specified and directed including necessary welding complete and including medium weight 03 Nos of MS butt hinges of size 75mm / 100mm / 125mm and 01 No 50mm Size of medium weight MS butt hinge complete all as specified and directed.

M&L PCC (1:3:6) type C-2 (40 mm graded aggregate) filling back of chowkats complete all as specified and directed..

M&L 35 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides with both face is covered with deco rative face veneer with lipping/frame to match complete all as specified and directed.

S&F 35mm thick 2nd class hard wood Glazed and skeleton shutters open rebated & prepare to receive glass, gauge etc (without sash bars /edges of framing plain chamfered or rounded, fitted with cut and mitred beds for securing glass etc) size of members of shutters as spd in SSR Part-I section-8 clause 8.2 (A) complete all as specified and directed.

S&F Framed brackets of angles or tees with web and flanges cut to shape for cooler stand, drilled and countersunk for screw, including bending and welding angles, as necessary, gusset plates, riveting, etc.. n exc 10 kg each brackets, conforming to Fe.290.Gde-E-165 complete all as specified and directed.

M&L for mild steel framed work as in doors ( as in chowkats)or gates of angle or other section with guest plates rails, braces rail etc exculsive of steel sheeting or other covering hanging also fastening and fixing complete confirming to Fe-410- W(Gde- E-250) quality- B including shop coat of red oxide including preparation of surface before fixing complete all as specified and directed.

S&F solid PVC door/cup board frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, suppling and fixing in opening complete all as specified and directed.

S&F factory made solid PVC moulded door shutter with wood free EPS 28 to 30mm thick (Stile) with flush panel with 2mm thick moulded PVC sheet on the front face & 2mm plain colour PVC sheet on back face complete all as specified and directed.

Steel ventilator with top hung shutter including hinges, steel peg stay, lugs as in hold fast with locking arrangements, complete all as specified and directed.

Steel windows with side hung double shutters (window consisting of two shutters out side and two shutters of similar dimension inside of single MS Frame) box type hinges with steel handle of 100mm and steel peg stay, complete with glazing bars, and including MS guard bars and grills made out of 10mm MS square bar (Grill and guard bars shall be provided as per directions of Engr-in- Charge during execution of work and cooler parten where as required) dovetailed or welded complete all as specified and directed.

S&F Galvanized mild steel wire cloth 0.45 nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tank or galvanized wire staple complete all as specified and as directed.

S&F Sheet glass, ordinary quality, 3mm thick and glazed with oil putty or wooden beads, in square n exc. 0.5 Sq m each pane, complete all as specified and directed.

S&F 3mm thick figured glass, pin head type and glazing with oil putty or wooden beads in square n.exc 0.5 sqm each complete all as specified and directed.

S&F Aluminium alloy, anodised, sliding door bolt with hasp, staple (both type) 300mm longh, and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed.

S&F Aluminium anodised 150mm long barrel tower bolt of extruded section and fixing complete all as specified and directed.

S&F Aluminium handles cast type anodised 150mm complete all as specified and directed.

S&F Butt hinges 100mm medium weight stainless steel complete all as specified and directed.

S&F Aluminium anodized barrel tower bolt of extruded section and fixed complete of size 125 mm longcomplete all as specified and directed.

S&F Aluminium handle cast type anodized of size 125mm complete all as specified and directed.

S&F Floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel springs, fixed in floor with over all length of cover plate 150mm

Dismantling floor, hearth or wall tiling , terrazzo topping on walls including cement mortar , bedding (but no backing) removing serviceable tiles and rubbish off the premises complete all as specified and directed.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc and Brushing neat cement slurry with 3.0kg of cement per sq. metre complete all as specified and directed.

M&L Vitrified coloured tiles, jointless , light shade of size 600mm x 600mm x 9 to 10 mm thick, as in floors etc bedded & jointed in neat cement slurry over and including 15 mm thick screed bed in cement mortar 1:4 and pointed in white or coloured cement to match the colour of tiles, complete all as specified and directed.

M&L Vitrified coloured tiles,joint less , light shade 600mm x 600mm x 9 to 10mm thick, on vertical surfaces such as skirting / dado etc bedded & jointed in neat cement slurry over and including 10mm thick backing coat of cement mortar 1:4 and pointed in white or coloured cement to match the colour of tiles,complete all as specified and directed.

M&L Glazed ceramic coloured tiles 450x350mmx7mm thick for work vertical surfaces such as shirking/dado and risers to step etc set and jointed in neat slurry and pointed in white /coloured cement and pigment to match the tiles over and including 10mm thick cement plaster in CM 1:3 , complete all as specified and directed.

M&L 18 to 20mm thick black Granite stone (table rubbed and polished) in cooking plateform bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone over 15mm thick screed bed in CM 1:4 after roughing surfaces of old concrete floor by picking sweeping down with water to remove dust etc including cutting holes into or through reinforced cement concrete slabs , for gas pipe (Superficial area wxc 100 sq cm but n. exc. 250 sq cm.) complete all as specified and directed.

M&L 20mm dia ss steel coated drapery rods in one length per door/window, fancy type (engraved rods), designed & coloured as approved by GE providing with two nos of Bracket powder coated for holding curtain rod and Fiber fancy dome type or wall to wall fixed in repair complete all as specified and directed.

S&F 300mm ordinary rat tail mild steel rod pattern springs incl roller and roller plate complete

Dismantling water tanks exceeding 250 ltr capacity but not exc 500 ltrs complete all as specified and directed.

S&F Rotational molded polythene water storage tank vertical type with closed top hoisted and fixed in position all as spd in SSR part-I capacity 500 liter complete all as specified and directed.

S&F in repair 20 mm ball valves high pressure of PTMT with epoxy coated , aluminium rod & high density plastic ball screwed for iron pipe min wt 210 gms complete all as specified and directed.

Taking up or down 15 mm steel tubing and connections including clearing for refixing or removal to store.

Taking up or down 20 mm steel tubing and connections including clearing for refixing or removal to store complete all as specified and directed.

S&F Steel water tubing medium grade galvanised with all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete with all fittings (such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.) of nominal bore dia15 mm, complete all as specified and directed.

S&F Steel water tubing medium grade galvanised with all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete with all fittings (such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.) of nominal bore dia 20 mm, complete all as specified and directed.

Refixing old steel tubing and connections in new or old position with all fittings retrieved from Serial here-in-before and fixed (walls, ceiling, floors, etc) of 15 mm dia complete all as specified and as directed.

Refixing old steel tubing and connections in new or old position with all fittings retrieved from Serial here-in-before and fixed (walls, ceiling, floors, etc) of 20 mm dia complete all as specified and as directed.

Demolition of cement concrete (un-reinforced) of any description and in any position not otherwise specifically provided complete all as specified and directed.

M&L for sunken treatment with glass fiber reinforced modified cementitious coating system before the final coat of Latex Shield 2K (or equivalent) complete all as following :- Base Coat : Berger HS Latex plus (or equivalent) consumption base coat : 0.3 kg/m2 Reinforcement : Glass fiber Second and Third coat : Latex sheild 2K (or equivalent) Consumption top coat : 3 kg/m2 System reqquirements : density : 2.00 kg/ltr; Compressive strength: 0.5N/mm2 Wall penetration through the RCC slab must be sealed using Berger HS Repair (or equivalent). Intersection of base slab with wall must be provided with a 50 mm fillet using Berger HS Latex plus (or equivalent) modified mortar with a bonding coat of Berger HS Latexplus (or equivalent) modified cement slurry upto sft. All depressions, unevenness, surface honeycombng shal be repaired using Berger HS Latex plus (or equivalent) modifiled polymer mortar with a bonding coat of Berger HS latex plus (or equivalent) modified cement slurry. Including cleaning of RCC surface to remove dust, loose paricles, etc with compressed air or any other suitable technique depending on site conditions, grinding aby sharp edges, etc. Note :-The concerned items should be executed by OEM authorized applicator after signing of MOU (format attached as Appendix 'AB' on page no. 93 of tender documents as per Sch 'A' Note No 19 Page No 17).

M&L rendering 10 mm thick on fair faces of brick work or concrete surfaces in CM 1:4 with water proofing compound to be finished even and smooth without using extra cement complete all as specified and as directed (WPC to be measured & separately)

S&F 20mm dia High density polyethylene pipes (HDPE) of pressure rating 6 kgf/cm2 laid in as spout pipes to pour out residual water out from the treated area complete all as specified and as directed

M&L for hard core, of broken bricks broken to gauge n exc 63mm for laying sub base of thickness 150mm complete all as specified and directed.

M&L Cement concrete type D-2 1:4:8 (40mm graded crushed stone aggregate) in foundations, filling and mass concrete in sub base complete all as specified and directed.

M&L for 25mm thick PCC (1:2:4) type B1 with 20mm graded aggregate for laying floor tiles complete all as specified and as directed

M&L for non skid coloured Ceramic tiles 8 to 10 mm thick in light shade (square/ rectangular) polished, area of each tiles exc 0.11 sqm but not exceeding 0.18 sqm, in floors/Skirting etc. set, jointed and pointed with Berger HS tile adhesive anti slip white @1.2kg/sqm thickness upto 8 to 10mm (or equivalent) and epoxy material for sealing of tile joints with Berger HS Epoxy tile grout(or equivalent) to the floor of toilets and bathroom complete all as specified and as directed

Demolition of cement concrete in and paving (un reinforced) exc. 15 cm. thickness, below or above ground level, including removal of waste from defence land and dumping at a place as specified by civil authorities complete all as specified and as directed

S&F Vitreous china water closet Orissa pattern long pan size 580x440mm with trap front or back inlet and integral foot rest complete fixed in repair including lime concrete bedding and connection to drain or outgoing pipe and to flushing pipe and anti siphon pipe complete all as specified and as directed.

S&F PVC flushing cistern white shade low level 10 ltrs capacity, white with inlet ball valve, float and handle including bracket and flush pipe including connection to pipes, fixed in repairs complete all as specified and as directed.

S&F PVC connection 15 mm size with PTMT nuts of length 600 mm complete all as specified and as directed

S&F Tubular towel rail, brass chromium plated, 20 mm dia, D type, 60 cm long between Hangs, fixed in repairs complete all as specified and as directed

S&F sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs washers and wastes including bedding in cement mortar to dwarf wall or including fixing cantilever brickets and connecting union to pipe overall size 915mmx460mm bowl size 410mmx330mmx160mm complete all as specified and as directed

S&F kitchen sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes, coupling including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mmx420mm bowl size 410 mmx330mmx 160mm etc complete all as specified and as directed.

S&F Cutting existing 15 mm bore steel tubing for alterations or additions

S&F Stainless steel grating of 125mm size, male/female pattern with or without hole, fixed in nahani/floor traps with white/coloured cement, fixed in repairs, complete all as specified & directed.

S&F PVC 32mm dia waste pipe with CP coupling complete all as specified & directed.

S&F in repair Bib taps, chromium plated cast copper alloy, with fancy type capstan head, screwed down for iron pipe or for brass ferrule and fixed for bore of pipe 15 mm, fixed in repairs, all as specified and as directed.

S & F 15 mm bore chromium plated bib taps fancy type, cast copper alloy, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified & directed.

S & Fixed in repairs Angle stop valve cast copper alloy, with fancy type chromium plated capstan head, screwed down, high pressure screwed both ends for 15 mm bore iron pipe or for unions and fixed complete all as specified & directed.

S&F in repair CP brass hot & cold 15mm dia wall mixture with provision for overhead shower with 115 mm long bend pipe on upper sie connecting legs & wall flanges for mixing hot & cold water complete all as specified & directed.

S&F in repair CP brass hot & cold 15mm dia 3 in1 wall mixture for kitchen & wall flanges for mixing hot & cold water complete all as specified & directed.

S & F in repairs Chromium plated shower rose 125 mm size with or without swivel joints, any size, including fixing to steel pipe or union complete all as specified & directed.

S & F in repairs 20 mm dia Gun Metal, globe or Gate Valve with Iron wheel head Screwed both ends for Iron Pipe and fixed in repairs complete all as specified & directed.

Sheet glass shelf assembly consisting of 5,5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long make Jaguar or equivalent complete all as specified & directed.

S&F 600x450mm PVC cabinet mirror of superior quality complete all as specified and directed complete all as specified & directed.

Dismantling boarding any description fixed with screws complete all as specified and directed.

S & F Second class soft wood plain fillets square, rectangular or triangular in section, wrought secured with screws, cross sectional area exceeding 13 and not exceeding 25 Sq. cm complete all as specified & directed.

18/19mm thick Prelaminated particle board, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination fixed with screws to timber frame work as in cupboards , kitchen cabinat etc fixed in repairs complete all as specified & directed.

S&F Continuous (piano) hinges,width of flap when open is 30 mm mild steel, bright finish or electrogalvanised complete all as specified & directed.

S&F 100 mm long Extruded Aluminium alloy handles, fabricated type, anodised complete all as specified & directed.

S&F Magnetic catches of 25/30 mm size for cup Board shutter etc complete all as specified & directed.

S&F hasp and stapple, safety typeof Aluminium, anodised, including bolt to hinge type, fixed with screws of 100 mm complete all as specified.

TMT steel bars 10mm dia and over, cut to length bent to shape required, including cranking, bending spirally for hooping to columns, hooking ends and binding with mild steel wire (annealed) not less than 0.90mm dia, all as specified and directed.

TMT steel round bars 6 to 8mm dia and over, cut to length bent to shape required, including cranking, bending spirally for hooping to columns, hooking ends and binding with mild steel wire (annealed) not less than 0.90mm dia, all as specified and directed.

M&L Form work to soffit of suspended slab such as roof slab not exc 20 0 mm thick horizontal or slopinf flate including fair finished to concrete surfaces complete all as specified & directed.

M&L Form work to Edges of concrete flate floor and roof n.exc 20 cm wide and similar work exc 10 cm but not exc 20 cm wide rough finished to concrete surfaces complete all as specified & directed.

M&L RCC 1:2:4 Type B-1 (using 20 mm graded aggregate) in Roof slab, shelves supported on wall/column and the like etc complete as required complete all as specified & directed.

M&L Providing Precast cement concrete 1:2:4 Type B-1 (using 20 mm graded aggregate) in landings, cover slabs (for man holes etc) and the like etc complete all as specified & directed.

Demolition of reinforced cement concrete ( reinforcement cut as required to facilitate demolition) of any description and in any position not otherwise specifically provided for complete all as specified and directed.

Demolition of cement concrete in ground floors and paving (un reinforced) n exc. 15 cm. thickness, below or above ground level, complete all as specified.

M&L 75 mm thick PCC 1:3:6 type C-1, (using 20mm graded crushed stone aggregate) as in plinth protection finished even and smooth without using extra cement incl necessary joints complete all as specified and directed.

Dismantling cast iron or reinforced concrete drain pipes of 75/100mm bore, fixed with walls and taking out of trenches, if required all as specified and directed.

S&F PVC (SWR) pipes single socketed in any length with rubbering joints fixed to walls 110mm bore.

S&F PVC (SWR) pipes single socketed in any length with rubbering joints fixed to walls 75 mm bore.

S&F PVC (SWR) bends any radius 110mm bore with access door.

PVC(SWR) junction single (single 'T') equal or unequal 110mm bore with access to door ccomplete all as specified and directed.

S&F PVC (SWR) bends any radius 75 mm bore with access door.

PVC(SWR) junction single (single 'T') equal or unequal 75 mm bore with access to door ccomplete all as specified and directed.

M & L for PVC (SWR) multi floor trap diameter of outlet 75 mm with grating including jointing with solvent cement.

S&F Plate rack made out of 1.00 mm thick stainless steel sheet of size 750mm x 750mm x250mm , complete all as sepcified and directed.

M&L for preparation of new wooden surfaces of any description, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and as directed.

M&L for preparation of old steel surfaces of any description, over 10cm width or girth and applying two coats of synthetic enamel paint over red oxide primer, complete, all as specified and as directed.

M&L for two coats new steel surface synthetic enamel paint over a coat of red oxide primer on newly steel surfaces complete all as specified and as directed.

Material and labour for complete removal of existing treatment including fascias, cornices etc by scrapping with mechanical wall sander (having mechanical vacuum mechanism) having RPM not less than 1500, sanding pad of 80 Grit having dia of 7"/9" to make the surface free from dust, loose paint and loose plaster to be completely removed by skilled labour and repair of external wall/ chajjas to be done with repair mortar to get even surface including preparation of old surface of wall/ ceiling by filling cracks by Berger Bison Putty/ crack fill paste of Berger Paints or equivalent make and make good smoothen surfae by sand paper and applying two coats of premium acrylic smooth exterior emulsion of approved colour with silicon additive & Color stay Technology, Excellent Dirt Pick up resistance of Berger Paints Ltd or equivalent of other approved make with low VOC less than 50 gram/ litre as per the LEEDS specifications, Anti Algal properties in two coats @ 1.79 ltr (undiluted)/ 10 sqm diluted with water as per manufacturer instructions applied over one coat of acrylic water based exterior grade primer @ 0.9 ltr (undiluted)/10 sqm mtrs diluted with water in 1:1 ratio as per manufacture's instruction and all coats incl primer to be applied with fuly automatic airless spray machine of paint appliaction with a flow speed of minimum 1 ltr per minute having a pressure of 3300 PSI all as specified and directed. Allow 6-8 hrs to dry the surrface in subsequent coats of paint and including necessary scaffolding at any height complete all as specified and directed Make : Berger Paints Weathercoat Long Life Flexo/ Nerolac Paints excel Total/ Asian Paint Apex Ultima/ JK Maximo Ultra Note :-The concerned items should be executed by OEM authorized applicator after signing of MOU (format attached as Appendix 'CD' on page no. 97 of tender documents as per Sch 'A' Note No 19 Page No 17).

M&L for Complete removal of existing treatment from internal wall/ceiling surfaces including preparation of old surfaces and applying one coat of oil bound distemper over 3mm thick wall care putty complete all as specified and directed.

M&L for Preparation of new plastered surfaces and applying two coats of oil bound distemper on walls/Ceiling over 3 mm thick wall care putty complete all as specified and directed.

Demolition of brick work or stone masonary built in cement mortar including all quoins , arches, pillar etc but excluding ashlars facing dressed stone work and pre-cast concrete article complete all as specified and directed.

M&L Brick work with sub class ‘B’ bricks, straight or curved on plan exceeding 6 m mean radius built in cement mortar 1:6, complete, all as specified and as directed.

Brick work with sub class ‘B’ bricks ,straight or curved on plan exc 6 m mean radius and built in cement mortar 1:6 complete , but except bricks , i.e using serviceable bricks obtained from demolition complete all as specified and directed

Brick work in cement mortar 1: 4, using sub class ‘B’ bricks, straight or curved on plan any radius in half brick thick wall complete all as specified and directed.

M&L PCC 1:2:4 nominal mix type B-1 using 20mm graded crushed stone aggregate as in roof kerbs or mud stops etc rounded or chamfered on edges and the like including necessary form work complete all as specified and directed.

Complete removal of existing roof treatment or roof tile and removing from site to a place outside defence land as specified by civil authorities and clean the surface of roof with water and remove dust complete all as specified.

M&L for Home Sheild PU Roofkoat (or equivalent) is a one component liquid, solvent free, cold applied water-proofing membrane that is highly elastic and UV resistant with 10 years warranty. ASTM D 6083-97 a waterproofing and heat reflecting system having following key performace properties : 1. UV resistant, prevent yellowing and weathering 2. Highly elastic upto 350% and crack bridging 3. Excellent adhesion on porous and non-porous substrates 4. Tensile strength > 10 N/mm2 with Geo Textile fleece 5. Soler reflective Index (SRI) more then 109-111 ASTM E 1980-11 System : First coat : Providing and applying primer over the prepared surface with HS PU roofkoat Primer (or equivalent) Coverage :0.2kg/m2 (with 50 % dilution of water) Reinforcement : Geotextile 40 gsm Second coat : Home sheildroofkoat (or equivalent) Consumption : 0.5 kg/m2 Third coat : HS PU roofkoat (or equivalent) Consumption : 0.8 kg/m2 System buildup-1.5kg/sqm with geotextile of 40 gsm For accessible roof, tiles with scred/ adhesive may be fixed thereafter. Note :-The concerned items should be executed by OEM authorized applicator after signing of MOU (format attached as Appendix 'EF' on page no. 101 of tender documents as per Sch 'A' Note No 19 Page No 17). B134

M&L for providing cement concrete type B-0 1:2:4 (using 12.5 mm graded stone aggregate ) in roof padding, roof kerbs or mud stops, rounded or chamfered on edges finished even and smooth without using extra cement complete all as specified and directed.

S&F Plate rack made out of 1.00 mm thick stainless steel sheet of size 750mm x 750mm x250mm , complete all as sepcified and directed.

M&L for capilary rise treatment of walls as following :- Base coat: Berger HS Latex plus (or equivalent) Consumption base coat: 0.3 kg/m2 Second and Third coat: Latex sheild 2K (or equivalent) Consumption top coat: 3 kg/m2 System requirements: density: 2.00 kg/ltr Compressive strength: 0.5 N/mm2 Note :-The concerned items should be executed by OEM authorized applicator after signing of MOU (format attached as Appendix 'GH' on page no. 105 of tender documents as per Sch 'A' Note No 19 Page No 17).

M&L for soakage well excavation in any type of soil, foundation in PCC 1:3:6 walls of honeycombed masonry with top ring of M25 concrete incl intercepting chamber and screen chamber made of brick masonry in CM, RCC cover slab in M25/SFRC cover, interconnecting pipes of RCC/DWcC complete filled with brick bats of size 3.0 m dia X 6.0 m effective depth complete all as specified and directed.

M&L for RCC NP2 200 mm diameter pipes laid on 150 mm thick bed of PCC 1:4:8 with excavation in any type of soil, incl manholes/drop manholes of standard size made of brick masonry/RCC/Precast RCC with SFRC ventilating cover and frame incl all items and activities to execute and make sewer line functional complete all as specified and directed.

Taking out carefully copper/aluminium point wiring,Light,fan,socket or power complete with all fitting, fixtures such as switch socket out let, ceiling rose ,holder ,regulator,DBs etc including making good the disturbed surface of wall/floors complete

Taking down distribution boards/wooden board ,switch fuse units,steel enclosures for MCB of any type and removing from site all as specified and as directed by the Engineer in charge.

Material and labour for point wiring for one light controlled by one way switch with 1.5 Sqmm PVC insulated unsheathed single core multi-stranded copper conductor (FRLS) cable 1100 Volts grade drawn through and including rigid non metallic PVC concealed conduit (medium grade) of suitable dia along with 1.5 sqmm continuous PVC insulated unsheathed single core multi-stranded copper conductor (FRLS) cable for earth continuity wire, connected to earth dolly and to be terminated in and including pressed steel sunken boxes , readily available (Having wall thickness not less than 1.22 mm for boxes upto a size of 200 mmX300 mm and beyond that the wall thickness shall be not less than 1.63 mm) concealed type for mounting of modular switches, sockets, fan regulators alongwith modular plate etc including testing on completion complete including cutting chases for concealed conduit pinning in making good to facing and pointing in using cement mortar 1:3 and making good disturbed surface all as specified and as directed.

All as per item No 3 above but for one fan point controlled by one piano switch all as specified and as directed.

All as per item No 3 above but One light point controlled by two way switch

All as per item no-3 above but for one bell point controled by one bell push all as specified and as directed.

All as per ser item No 3 hereinbefore but for one 3 pin socket outlet 5 Amp Same board.

All as per ser item No 3 hereinbefore but for one 3 pin socket outlet 5 Amp independent.

All as per Item no 3 here-in-before but for one15 Amp 3pin switch socket outlet, independent with 2.5 Sqmm single core multi-stranded copper conductor cable (FRLS) along with 2.5 sqmm continuous PVC insulated unsheathed single core multi-stranded copper conductor (FRLS) cable for earth continuity wire all as specified and as directed.

Supply and fix modular type switch, one way 6 Amps , 1 module complete all as specified and directed.

Supply and fix modular type switch, Two way 6 Amps , 1 module complete all as specified and directed.

Supply and fix modular type switch, one way 16 Amps, 1 module complete all as specified and directed.

Supply and fix modular type socket 5 pin, 6 Amps 2 module complete all as specified and directed.

Supply and fix modular type socket 5 pin, 6 A/16 Amps 2 module complete all as specified and directed.

Supply and fix in repairs of Ceiling rose surface bakelite three terminals 240 volts complete, all as specified.

Supply and fix in repairs Lamp holder PVC case body of Bakelite with back plate suitable for batten fittings , all as specified and directed.

S&F LED Bulb cool white 12 Watt Elegant design direct fit for easy installation all as specified and directed.

Supply and fix in replacement of Bell push flush type piano 5 Amp complete, all as specified and directed.

Supply and fix in replacement Bell multi music 230 volt ,AC single pole complete all as specified and directed.

Supply and fix in replacement of Tube light fitting integrated type suitable for LED 20W indoor decorative aluminium extruded LED batten complete with hosing with all accessories pre wired and making connection with three core copper flexible cable of size 23/0.0076 from ceiling rose to PVC connection to light fitting complete all as specified and directed.

Supply and fix in replacement of Tube light fitting integrated type suitable for LED 10W indoor decorative aluminium extruded T5 LED batten complete with hosing with all accessories pre wired and making connection with three core copper flexible cable of size 23/0.0076 from ceiling rose to PVC connection to light fitting complete all as specified and directed.

Supply and fix in replacement of Factory made flush shutter type sheet metal enclosures, double door, for MCCB DB load link, Vertical, triple pole and neutral, 4 way IP-43, Suitable for MCCB up to 160A as incommer.complete all as specified.Make C&S cat no CSDBMCCB100DD04IP43S or equivalent model in HPL/ABB/Siemens

Supply and fix in repairs factory made epoxy powder coated Distribution board SPN 12 ways (SPN MCB DB) with metal door (IP-54 protection) fabricated from minimum 1.6mm thick CRCA sheet and fixed flush to wall and suitable for universal mounting and including 200 Amp copper bus bar, neutral bar, standard DIN rail, Earth bar and cable ties for cale management, top and bottom removable gland plates with Knockouts and suitable for one SPN/DP-MCB as incomer and SP MCBs outgoing complete all as specified and confirming to IS : 8623.

Supply and fix in replacement MCB SP-06 to 32 Amp,10KA, 240 volts complete all as specified.

Supply and fix in replacement of MCB SPN 32 Amp, 240 volts 50Hz AC supply, complete all specified and directed.

S&F in repair MCCB 415 Volt 25 KA 4 Pole 125 Amps complete all specified and directed.

S&F single core PVC insulated unsheathed multistranded copper conductor cable 1 Sqmm , 1100 Volts ISI marked drawn through existing point wiring complete all specified and directed.

Material and labour for sub main wiring with two single core PVC insulated (unsheathed) multistrand copper conductor FRLS cable of size 4 sqmm and one single core PVC insulated (unsheathed) solid copper conductor FRLS cable of size 4 sqmm as in continuous earth wire drawn into and including concealed PVC conduit medium grade 25mm dia ISI marked complete with fittings and fixings accessories complete and including cutting chases pinning in making good to facing and pointing in using cement moter 1:3 and making good disturbed surface incl taking down old one complete all as specified and as directed.

Material and labour for sub main wiring with two single core PVC insulated (unsheathed) multi strand copper conductor FRLS cable of size 6 sqmm and one single core PVC insulated (unsheathed) solid copper conductor FRLS cable of size 6 sqmm as in continuous earth wire drawn into and including concealed PVC conduit medium grade 25mm dia ISI marked complete with fittings and fixings accessories complete and including cutting chases pinning in making good to facing and pointing in using cement moter 1:3 and making good disturbed surface incl taking down old one complete all as specified and as directed.

M & L in repair for earthing complete with galvanized steel earth plate 600x600x6mm thick buried vertically in ground to depth not less than 2.25 mtr below ground level, with top edge of the plate not less than 1.50 mtr below normal ground level, connected to GI earth lead wire 4 mm dia by means of bolts, nuts, check nuts and washers of galvanized iron and connection to main switch board of panel, including watering pipe GI 20 mm bore light grade 15mm bore for earthing lead, wire mess, funnel, salt, charcoal dust, excavation and refilling pit with PCC 1:2:4 type B1(using 20mm dia stone aggregate) reinforced with 6mm dia round bar @ 75mm cement concrete both always with MS handle 12mm dia and frame all as shown in electric plate No 3 in page 497 of SSR Part I (2009) and pouring extra Clay Soil of qty not less than one cubic meter into the earth pit and also removal of excavated soil not less than 50 mtr from the earthing place all as specified and directed and tested on completion. including testingall as specified and directed by E-in-Charge.

Supply and fixing LED Bldg security light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with suitable size and length of 1.5 sqmm copper conductor with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete.

S & F LED light fitting 1x9W/1X10Wbulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size.

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250mm , connecting electrically using 3 core 0.75 Sq mm PVC insulated flexible copper conductor cable over all sheathed all as required at site and as directed.complete all as specified and directed.

Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300mm sweep with, blades, and frame and louvers connecting electrically using 3 core 0.75 Sq mm PVC insulated flexible copper conductor cable over all sheathed all as required at site and as directed.complete all as specified and directed.

M&L for cutting of suitable size of holes for 250/300 mm exhaust fan in wall and grouting of nuts and bolts in wall and making good to match with existing walls complete all as specified and directed.

Supply and fix in repair tamper proof with inbuilt intelligence electronic Energy meter single phase, two wire direct connected meter with parameter (voltage P-n, PF, Frequency current line KW demand, LDC display, optical port class 1.0s), 240 volts 10-60 Amps complete with meter box single phase with locking arrangements molded in UV stabilised transherant/flame retardant high grade engineering plastic with unique arrangements for plifer proof interlocking with hinge type box with connection of suitable size wire including seal and sealing wire and furnishing details of Qtr No, Meter No, Initial reading writing with paint of MES No all as direcrted by Engr-in-Charge make ISI mark. Make :L&T cat No-WM101BC7DL0BOX or equivalent Note : (i) MES No to be marked on the meter with black paint as directed and all details i.e bldg No, qtr No, initial reading, Serial no of new meter and final reading ifreadable withqtr No& ser No as per specified format to be submitted by Contractor. (ii) All old meter removed from bldg to be deposited to MES store yard.

Taking down fan, sealing cable end, dismantling blades and removing fan and blades to MES store complete all as specified and directed.

Supply and fixing ceiling fans complete with blades, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) Anti Suicide Fan Rod of suitable size and length with the provn, If the load on fans exceeded 22 kgs, than the smart rod/pipe opens from its centre and spring in the pipe expands, The fan Rod should be tested at Govt of India's MSME Labs for its functionility and the test report from Labs should be submitted to the Engr In Charge.

Supply and fix electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, PVC connection pipes two Nos etc all as specified and directed.

Supply and fix sheet metal enclosure with single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole mcb complete all as specified and directed.

Cutting existing steel tubing 15 mm bore for alterations or additions (Each cut measured) complete all as specified and directed.

Screwing existing steel tubing 15mm for alterations or additions complete all as specified and directed.

S & F Tubes medium grade galvanized 15 mm dia with fittings such as socket, bend and fixed complete to walls and ceilings complete all as specified and directed.

S&F Stop valve/angle valve cast copper alloy screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe of four unions and fixed complete all as specified and directed.

S&F Bib tap 15mm chromium plated cast copper alloy with crutch or butterfly screwed down for iron pipe and fixed complete all as specified and directed.

Taking out/down unserviceable, defective cable any Type/size including disconnecting all the electrical connections all as required at site and complete all as specified and directed.

Material and labour for cable XLPE insulated screened PVC bedded, galvanised steel strip or wire armored, electric power cables (heavy duty 1100 Volts grade with stranded aluminium conductor of size 35 Sqmm 3.5 Core, including glands, lugs, nut, bolts, washers as required at site, testing complete all as specified and directed.

Excavation in trenches not exceeding 1.5 metres wide and not exceeding1.5 metres in depth and getting out in any type of soil complete all as specified and directed.

Returning, filling in, including spreading , leveling , watering and well ramming in layer not exceeding 25cm each layer all as specified and directed.

Removing excavated material not exceeding 50M and depositing where directed at a level not exceeding 1.5 metre above the starting point complete all as specified and directed.

M&L for Sand cushioning to underground cables provided with a layer of sand 8cm thick before laying the cable in trenches and 15cm thick after laying the cable in trenches complete all as specified and directed.

S & F Steel pipe glavanized grade of 40 mm core laid in trenches or under ground/floor or road of fixed with pole for protection of cable including clams with bolts nuts and wasers complete as as specifed and directed.

Sub class ‘B’bricks for covering to cable laid dry flat ,with width equal to the length of brick complete as as specifed and directed complete as as specifed and directed.

M & L for replacement of tubing GI "MG" with all fittings laid in floor or trenches including taking out old UNSV pipe of size 50 mm dia complete all as specified and directed

M & L for replacement of tubing GI "MG" with all fittings laid in floor or trenches including taking out old UNSV pipe of size 25 mm dia complete all as specified and directed

M & L for replacement of gun metal globe or gate valve with iron wheel head, screwed both ends for iron pipe and fixed of size 50 mm bore complete as as specifed and directed.

M & L for replacement of gun metal globe or gate valve with iron wheel head, screwed both ends for iron pipe and fixed of size 25 mm bore complete as as specifed and directed.

M & L Cutting existing 80/100/150 mm GI pipe and inserting GI Tee of size 100x100x50 mm for tapping including necessary earth work and making flange for connection of new 50 mm of GI pipe including complete as as specifed and directed.

Dismantling of old U/S valve pit of size 4000x400x400 mm ( internal dimensions of the chamber) including and removing the debris at a distance not exceeding 50 Mtr and M/L for brick massonary with cement mortar with 1: 6 , 23 cm and flush pointing externaly work proceeds in the same mortar complete ( using 30% old bricks & 70% New bricks) complete with the following specifications and as directed by Engr-in-Charge. Note :-(i) 10mm thick plaster internally in CM 1:6.(ii) Flooring 40mm thick in PCC 1:2:4 type B-1 over 75mm thick hard core of guage not exc 63mm thick. (iii) Angle iron frame 40X40X6mm thick for cover and mild steel 3.15mm thick cover with locking arrangement,handle and necessary hinges etc, (iv) PCC 1:3:6 type C-2 100mm thick in foundation .(v) Two coat of synthetic enamelled paint to cover internally and externally over a paint of Red Oxide primer.

Please Enable Macros to View BoQ information