Balance Work of Proposed Dibrugarh Town Hall at Dibrugarh under UIDF for the year 2023-24

Amount

Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete.

Providing and laying in positon cement concrete of specified grade excluding the cost of centering and shutttering - All work up to plinth level: 1:3:6 (1 Cement : 3 coarse sand (zone-III) : 6 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size)

Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centering , shuttering, finishing and reinforcement - All works up to plinth level: 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels,bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources).

Centering and shuttering including strutting, propping etc, and removal of form for: Lintels, beams, plinth beams, girders, bressumers and cantilevers

Columns, Pillars, Piers, Abutments, Posts and Struts

Stairs, (excluding landings) except spiral-staircases

Edges of slabs and breaks in floors and walls 5.9.16.1 Under 20 cm wide

Suspended floors, roofs, landings, balconies and access platform with water proof ply 12 mm thick

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : 6.4.2 Cement mortar 1:6 (1 cement : 6 coarse sand)

12 mm Cement plaster of mix 1:6 ( 1 cement : 6 fine sand)

15 mm Cement plaster on the rough side of single or half brick wall mix 1:6 ( 1 cement :6 fine sand)

Cement plaster skirting up to 30 cm height, with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement. 18mm thick

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth. 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5m, disposed earth to be levelled and neatly dressed. All kinds of soil.

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundations and plinth in : 6.12.2 cement mortar 1:4 (1 cement : 4 coarse sand)

Centering and shuttering including strutting, propping etc, and removal of form for: Foundations, footings, bases of columns etc. for mass concrete

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. 11.41A.1 Double charge vitrified tile polished finish of size 11.41A.1.1 Size of Tile 600 x 600 mm

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete 11.46.2 Size of Tile 600x600 mm

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge 11.56.2 Polished Granite stone slab of all colour and texture except Black, Cherry/Ruby Red

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 11.26.1 25 mm thick

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to 3match the shade of the slabs, including rubbing and polishing complete.

Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earthwith lead upto 50 metres.

Supplying and stacking at site. 16.3.3 53 mm to 22.4 mm size stone aggregate

Laying, spreading and compacting stone aggregate of specified sizes to WBM specifications in uniform thickness, hand picking, rolling with 3 wheeled road/vibratory roller 8-10 tonne capacity in stages to proper grade and camber, applying and brooming requisite type of screening / binding material to fill up interstices of coarse aggregate, watering and compacting to the required density .

Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge 16.91.2 80 mm thick C.C. paver block of M-30 grade with approved color design and pattern.

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately). 9.1.2 Sal wood

Providing and fixing 35 mm thick factory made laminated veneer lumber door shutter conforming to IS : 14616 and TADS 15:2001 (Part B), fixing with butt hinges of required size with necessary screws, all complete as per directions of Engineer- in-charge and panelling with panels of :(Note:- Butt hinges and necessary screws shall be paid separately) 12 mm thick one side Pre-laminated particle board (decorative lamination on one side and other sides balancing lamination) grade -1, medium density flat pressed, three layer particle board FPT - I or graded wood particle board FPT-1 conforming to IS : 3087 bonded with BWP type synthetic resin adhesive as per IS : 848 and pre-laminated conforming to IS : 12823, Grade -1, Type II marked :

Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.

9.147D.2 Three track three panels sliding window with fly proof SS wire mesh (Two nos. glazed & one no. wire mesh panels) made of (small series) frame 92 x 44 mm & sash 32 x 60 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area of window upto 1.75 sqm).

Providing and fixing factory made uPVC white colour sliding glazed door comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick alvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension uPVC extruded glazing beads, uPVC extruded interlock and uPVC extruded Inline sash adaptor (if required), EPDM gasket, wool pile, zinc alloy (white powder coated) handle with key on one side of extreme panels along with zinc plated mild steel multi point locking having transmission gear with keeps, zinc alloy (white powder coated) cresent lock (if required), stainless steel (SS 304 grade) body with adjustable double nylon rollers (weight bearing capacity to be 120 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.

9.147F.4 Three track three panels sliding door with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) made of (big series) frame 116 x 45 mm & sash 46 x 82 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of door above 2.00 sqm upto 5.00 sqm)

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. 5.22.6 Thermo-Mechanically Treated bars of grade Fe-500D or more.

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. 10.16.2 Hot finished seamless type tubes

Providing & fixing at all heights, levels and locations Mill finish Aluminium alloy roofing sheets of alloy IS designation 31500, temper Hx8 conforming to IS 737 and dimensions as per IS code 2676 with characteristics of good formability and corrosion resistance. The profile sheets shall be fixed to truss members in slope or required pitch or curvature with Hex cap headed self drilling/tapping Stainless steel screws M6, 50 mm long with 3 mm EPDM seal washer etc. all inclusive of labour, scaffolding, T&P and sundries etc. complete as per directions of the Engineer-In-Charge. (Cost of truss/frame work shall be paid separately). 12.64.1. 0.56 mm, troughed profile with center to center pitch of 200 mm, depth of 32 mm, overall profile width1092 mm, cover width 1000mm.

Providing and fixing of Pre-coated colour or mill finish Aluminium Roofing Accessories in 0.71 mm thickness ,Alloy 31500 (IS designation) [Aluminium Alloy (AA) 3004 (ISO designation)] For color, coating shall be 5-7 microns epoxy primer on both sides of the sheet and polyester top coat 15-18 microns, using self drilling/ tapping SS screws of size 6 x 50mm with 3mm thick EPDM seal and SS plain washer complete : 12.66.1 Precoated/mill finish aluminium Ridges plain (500- 600mm)

Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2 mm and braced with flat iron diagonals 20x5 mm size, with top and bottom rail of T-iron 40x40x6 mm, with 40 mm dia steel pulleys, complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of approved steel primer.

Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters. 10.6.1 80x1.25 mm M.S. laths with 1.25 mm thick top cover

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.

Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main "T" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge.

12.5 mm thick fully Perforated Gypsum Board tile made from plasterboard having glass fibre conforming to IS: 2095 part I, of size 595x595 mm, having perforation of 9.7x9.7 mm at 19.4 mm c/c with center borders of 48 mm and the side borders of 30 mm, backed with non woven tissue on the back side, having an NRC (Noise Reduction Coefficient) of 0.79, with 50 mm resin bonded glass wool backing.

Providing and fixing in position wall panelling at all heights with integral densified calcium silicate panels/tiles of size 595 x 595mm, having NRC (Noise Reduction coefficient) of 0.50 (minimum) as per IS 8225:1987, Light reflectance of 85% (minimum). Non combustible as per BS:476 (part-4), fire performance as per BS:476 (part 6 &7), humidity resistance of 100%, thermal conductivity <0.043 W/m K as per ASTM 518:1991, comprising of a frame made from especially fabricated galvanised mild steel sheet 0.50 mm thick pressed section (galvanizing @120 grams per sqm including both sides) i.e.vertical studs of size 48 x 34 x 36 mm are placed at 600mm center to center in a floor and ceiling channel section of size 50 x 32m fixed to the floor and soffit at 600mm centers using 12mm dia,50mm long wedge type expanded zinc alloy dash fastner with 10mm bolt. This same channel is then to be fixed in horiziontal direction at 600mm center to center so as to form a grid of 600mm x 600mm. Glasswool of 50mm thickness is then to be inserted in the slots and finally calcium silicate non combustible panels/tiles are to be screw fixed with self tapping pan head nickel coated mild steel screws of size 13 x 3.2mm on to this grid leaving an even groove of 1 mm between the panels. The joints between the panels are to be duly jointed and finished using recommended jointing calcium silicate based compound and fiber joint tape roll 50mm wide (90 metre )roll and two coats of primer suitable for panelling as per manufacturer's specification as per direction of Engineer-in-Charge all complete. 26.24.1 With 15 mm thick fully perforated square/butt edge light weight calcium silicate panels/ tiles 26.24.1 With 15 mm thick fully perforated square/butt edge light weight calcium silicate panels/ tiles

Providing and fixing 15 mm thick false ceiling tiles at all heights with integral densified calcium silicate reinforced with fibre and natural filler false ceiling tiles of Size 595x595 mm of approved texture, design and atterns having NRC (Noise Reduction coefficient) of 0.50 (minimum) as per IS 8225:1987, Light reflectance of 85% (minimum).Non combustible as per BS:476 (part-4), fire performance as per BS:476 (part 6 &7), humidity sistance of 100%, thermal conductivity < 0.043 W/m K as per ASTM 518:1991,in true horizontal level on the existing frame work consisting of T-sections and Lsections suitably fixed according to tile size as per direction of Engineer-in-charge

Providing & fixing false ceiling at all heights with GRG (Glass Fibre Reinforced Gypsum) false ceiling tiles of Size 595x595 mm of approved humidity resistance of 99%, NRC0.50 to 0.75 as per IS 8225:1987 Non combustible as per BS 476 (part 4)-1970 and light reflectance of 85% (minimum) to be laid in true horizontal level suspended on interlocking metal T-Grid of hot dipped galvanised iron section of 0.33mm thick galvanized @ 120 grams per sqm including both sides) comprising of main-T runners of size 15x32 mm of length 3000 mm,cross - T of size 15x32 mm of length 1200 mm and secondary intermediate cross-T of size 15x32 mm of length 600mm to form grid module of size 600 x 600 mm, suspended from ceiling using galvanised mild steel items (galvanizing @ 80 grams per sqm) i.e. 50 mm long, 8 mm outer diameter M-6 dash fasteners, 6 mm dia fully threaded hanger rod upto 1000 mm length and L-shape level adjuster of size 85x25x2 mm. Galvanised iron perimeter wall angle of size 24x24x0.40 mm of length 3000 mm to be fixed on periphery wall / partition with the help of plastic rawl plugs at 450 mm center to center and 40 mm long dry wall wood screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in-Charge 26.26.2 With fully perforated 12 mm thick micro tegular edged or 10 mm thick square edged GRG false ceiling tiles.

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Finishing walls with Acrylic Smooth exterior paint of required shade:New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20kg/ 10sqm.

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : 13.61.1 Two or more coats on new work

Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @0.75 ltr/10 sqm of approved brand and manufacture

Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/ 10 sqm over an under coat of primer applied @ 0.80 ltr/ 10 sqm of approved brand and manufacture

Providing and fixing aluminium sliding door bolts I.S.I. marked anodised ( anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete.with nuts and screws etc. complete : 300x16 mm

Providing and fixing aluminium tower bolts I.S.I. marked anodised ( anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete.with nuts and screws etc. complete : 250x10 mm

Providing and fixing aluminium handles I.S.I. marked anodised ( anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete.with nuts and screws etc. complete : 125 mm

Making plinth protection 50 mm thick of cement concrete 1:3:6 (1 cement: 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including finishing the top smooth.

Supplying chemical emulsion in sealed containers including delivery as specified. 2.34.1 Chlorpyriphos/ Lindane emulsifiable concentrate of 20%

Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) : 2.35.1.1 With Chlorpyriphos/ Lindane E.C. 20% with 1% concentration

Expansion Gap Treatment Providing and fixing pre-moulded joint filler in expansion joints of RCC roads / CC pavements after making the joints dust free with high pressure air jet cleaners, all complete as per direction of the Engineer-in-Charge. (Pre-moulded joint fillers shall be made of bitumen hot sealing compound impregnated fibre board having impregnation more than 35%, conforming to IS:1838 for fibre board and IS: 1834 for hot sealing bitumen compound grade A.)

Providing and filling in position rubberized bitumen hot sealing compound for sealing of expansion joints in roads / pavements all complete as per direction of the Engineer-in-Charge.

AIRCONDITION HI SIDE WORKS Variable Refrigerant Volume / Flow Air-conditioning System Supply, Installation, testing and commissioning of Cooling only Variable Refrigerant Flow /(VRF) Modular type (with the latest technology/version) with All-Inverter driven Compressor, system with stepless modulation for both heating & cooling modes, complete with indoor and outdoor units, individual remote controller and centralized controller, interconnected refrigerant piping with insulation, Y joints, Refrigerant to be used shall be - R 410 A only. The unit shall be suitable to work on 415V +/- 10%, 3 Phase, 50Hz AC power supply. Outdoor Units Supply of Modular type outdoor condensing units equipped with highly efficient Inverter Compressors ,with nominal capacities as mentioned below :- 64 HP - Top Discharge VRF Outdoor Unit

54 HP - Top Discharge VRF Outdoor Unit

20 HP - Top Discharge VRF Outdoor Unit

Indoor Units Supply of VRF Indoor units equipped with statically and dynamically balanced fan to give require air flow, pre-filters for clean air within the enclosed area,with nominal capacities as mentioned below :- High Static Ductable units of following capacities with corded remote controller :- 8.5 TR (3400 CFM)

4 Way Cassette units of following capacities along with decorative Grille and cordless remote controller :- 3.18 TR (1050 CFM)

2.84 TR (880 CFM)

Supply of Refnets

LOW SIDE WORKS Installation, Testing & Commissioning of VRF Units , with outdoor mounting, pressure testing, nitrogen flushing and vacuuming etc. Outdoor Units 64 HP - Top Discharge VRF Outdoor Unit

54 HP - Top Discharge VRF Outdoor Unit

20 HP - Top Discharge VRF Outdoor Unit

Indoor Units Installation, Testing & Commissioning of VRF Indoor Units with proper mounting, pressure testing, nitrogen flushing and vacuuming etc. High Static Ductable units of following capacities 8.5 TR (3400 CFM)

4 Way Cassette units of following capacities along with decorative Grille and cordless remote controller :- 3.18 TR (1050 CFM)

2.84 TR (880 CFM)

Lifting & Shifting Lifting & Shifting of ODU from Ground Level to terrace Level or as per site requirement

Refrigerant piping and piping accessories Supply, Installation and Testing of Hard/soft Copper refrigerant piping of required sizes for suction & liquid, with Superlon/Accoflex insulation material for the gas/liquid line. All the copper piping covered with Insulation as per specifications

Installation and Testing of Refnets

Control cabling Supply, Installation and Testing of Control cabling with copper conductor min. 2 core x 1.5 sq.mm. cable with end termination for Indoor units enclosed in PVC Conduit

Drain Piping Supply, Installation and Testing of Drain piping in hard cPVC with all fittings, properly insulated with nitrile rubber, supports and clamps, including drilling hole in wall to route the drain pipe

Refrigerant Gas Top-up required Supply and Charging of extra Gas required for all the above units as per Copper Piping length and the Indoor unit capacity (With R410A Gas)

M. S. Stands Supply and Installation of M. S structural work for Outdoor units duly painted with black epoxy paint (Type - Table Top Stand)

Air Distribution Fabrication, Supply and Installation of G.I. Duct - 120 GSM for Supply Air 24 G

Supply and Installation of Al powder coated 6" linear Grill for Suppy Air with VCD

Fabrication, Supply and Installation of G.I. Duct - 120 GSM for Supply Air 24 G

Supply and Installation of Al powder coated 8" linear Grill for return Air

Supply and Installation of Canvas connection

FRESH Air Distribution - SITC Fabrication, Supply and Installation of G.I. Duct - 120 GSM 24 G

Thermal Insulation - 13 mm Nitrile Rubber Insulation

Inline Fan for Fresh Air

Duct Thermal Insulation Supplying and fixing of 19 mm thick duly laminated aluminum foil of mat finish closed cell Nitrile rubber (Class “ O ” ) insulation on existing duct after applying suitable adhesive for Nitrile rubber. The joints shall be sealed with 50 mm wide and 3 mm thick self adhesive nitrile rubber tape insulation complete Make - Armacell / K Flex / Supreme/A-Flex

Duct Acoustic Insulation Supplying & fixing of acoustic insulation inside ducting with 10mm thick open cell nitrile rubber(class O) of density 140Kg/cu.m-160 Kg/Cum insulation with bolts nuts GI washers etc as required. Make - Armacell / K Flex / Supreme/A-Flex

UNDERDECK INSULATION Supply and Installation of of Nitrile rubber underdeck insulation 25mm thick with Al foil coating complete with adhesive and chicken mesh

POWER CONNECTION FROM APDCL WITH TRANSFORMER Supply,Testing,Erection of ACSR Rabbit conductor 50 sq mm as per IS 398-2 (1996)

Supply of Pre-Stressed Cement Concrete Poles Length 9.75m

Erection of RCC/ PCC pole of following length in brick ballast and ramming the foundation, finishing with 150mm thick cement concrete (1:3:6) layer on top with including excavation and refilling etc as required. Above 8.0 metre and upto 11.0 metre

Supply and erection of 100mm X 65mm pin insulator complete with GI Spindle and nuts etc. as required

Supply and erection of Anchor Clamp 100 mm x 65 mm

Supplying and erection of stay set complete (galvanised) with 19/20 mm dia X 1.8 metres long stay rod, anchor plate of size 45 cm X 45 cm X 7.5 mm, thimble, stay clamps, turn buckle ( 20 mm X 60 cm ), 7/ 4.00 mm dia G.I. stay wire and strain insulator etc in cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size ) foundation including excavation and refilling etc. as required

Supplying of channel iron 75 mm X 40 mm X 6 mm (7.14 kg per metre) pole top bracket/ cross arm for single 11 KV over head line conductor complete with 50 mm X 6mm flat iron clamp, bolts, nuts and washers including drilling holes for insulator pins, bolts and nuts etc and painting with primer and finish paint as required

Supply and erection of F clamp /Top Bracket Clamp

Erection of angle iron/ channel iron cross arm on wood/ RCC/ PCC/steel tubular/ rail pole etc. as required.

Supply and erection of 11kV DO Fuse

Supply and erection of 11kV GAOB switch 300Amps with Earth Switch

Supply and installation of 12kV LA IEC-99-4 Lightining arrestor

Supply and installation Tee Connectors asper technical specification for 11 KV line

Supply and installation of PG Clamp as per technical specification for 11 kv line

Construction of 250 KVA Sub-Station as per APDCL Estimate (Inclusive of Transformer, CT/PT, Meter, AMR, Control Cable, Supervision & Contingency charge and all)

Estimate for APDCL paper works. ( Load sanction through proper Channel, Feasibility Report from Grid Sub-Station, approval of Estimate through proper channel, Transformer charging approval from with drawing and Test Report, Load and Transformer agreement, Load release from Area Manager and Meter Installation through T & C Dept. )

Arranging & Paying Load Security to APDCL including all associated Charges.

MAIN LT PANEL Supply, testing, & commissioning of following type compartmentalised floor mounted cubicle board from 2 mm thick CRCA sheet dust and vermi proof duly phosphatized & powder coated 9 tank treatment. Incomer 01 for RAW POWER Input : 1 No. 800 A, 4P Air circuit breaker ACB EDO type 50 kA Icu at 220...440 V AC 50 Hz conforming to IEC 60947-2 with Overload protection,Instantaneous protection,Internal fault protection Drawout type for easy maintenance and repair with Panel door mounted Key lock for Extended ROM. Led type on, off & Trip indicating lamp. 1 Set (3 Nos) - 800/5A, 10 VA, Cl-1 Current Transformer. 1 Set - Cl-1 Multi Function Digital Meter with RS 485 BMS COMPATIBALE. 1 Set - 3 Nos R-Y-B Phase Indication Lamp with 6A MCB Protection. Bus Bar: 1000 Amp copper TPN Bus Bar covered with colour coded PVC Heat Shrinkable Busbar Insulation Sleeves, mounted on Porcelain/DMC/SMC Insulators. Outgoing: a) 01 No. - 250 A, 4P MCCB Thermal Magnectic type, Icu = 25 kA ,Extended rotary operated mechanism b) 01 No. - 200 A, 4P MCCB Thermal Magnectic type, Icu = 25 kA ,Extended rotary operated mechanism c) 02 No.- 150 A 4P MCCB Thermal Magnetic type, Icu=25 kA ,Extended rotary operated mechanism d) 05 No.- 63A 4P MCB, Icu=10 kA Earth Bus Bar: 50 mm x 5 mm GI flat earth bus bar running along the base of the frame covering entire length of the panel with GI bolt and nuts and number of drilled holes as required for earth connection. Contractor should submit the GA Drawing of panel board and obtain necessary approval for authority before placing purchase P.O. of the panel board. 1 - Danger Board. Complete Board as stated above. [Non Schedule Item].CPRI approved.

LT PANEL for commercial area distribution Supply, testing, & commissioning of following type compartmentalised floor mounted cubicle board from 1.6 mm thick CRCA sheet dust and vermi proof duly phosphatized & powder coated 9 tank treatment. Incomer 01 for RAW POWER Input : 1 No. 250 A, 4P MCCB Microprocessor type with earth fault protection (Icu = 25 kA, Ics = 100% Icu) with extended rotary operated mechanism and O\L, S\C, G\F, E\F Releases with Panel door mounted Key lock for Extended ROM. Led type on, off & Trip indicating lamp. 1 Set (3 Nos) - 250/5A, 10 VA, Cl-1 Current Transformer. 1 Set - Cl-1 Multi Function Digital Meter with RS 485 BMS COMPATIBALE. 1 Set - 3 Nos R-Y-B Phase Indication Lamp with 6A MCB Protection. Automatic Transfer switch :The Automatic transfer switch should have complete switching neutral with zero position. 4 pole 415 v 50hz,Confirming to IS 13947 / IEC 60947. 01 nos of 250 Amp 4 P . Bus Bar: 300 Amp copper TPN Bus Bar covered with colour coded PVC Heat Shrinkable Busbar Insulation Sleeves, mounted on Porcelain/DMC/SMC Insulators. Outgoing: a) 03 No. - 63A, 4P MCCB Thermal Magnectic type, Icu = 25 kA,Extended rotary operated mechanism b) 04 No.- 63A 4P MCB, Icu=10 kA c) 14 No.- 25A DP MCB, Icu=10 kA Earth Bus Bar: 50 mm x 5 mm GI flat earth bus bar running along the base of the frame covering entire length of the panel with GI bolt and nuts and number of drilled holes as required for earth connection. Contractor should submit the GA Drawing of panel board and obtain necessary approval for authority before placing purchase P.O. of the panel board. 1 - Danger Board. Complete Board as stated above. [Non Schedule Item].CPRI approved.

LT PANEL for Guest house power distribution Supply, testing, & commissioning of following type compartmentalised floor mounted cubicle board from 1.6 mm thick CRCA sheet dust and vermi proof duly phosphatized & powder coated 9 tank treatment. Incomer 01 for RAW POWER Input : 1 No. 200 A, 4P MCCB Microprocessor type with earth fault protection (Icu = 25 kA, Ics = 100% Icu) with extended rotary operated mechanism and O\L, S\C, G\F, E\F Releases with Panel door mounted Key lock for Extended ROM. Led type on, off & Trip indicating lamp. 1 Set (3 Nos) - 200/5A, 10 VA, Cl-1 Current Transformer. 1 Set - Cl-1 Multi Function Digital Meter with RS 485 BMS COMPATIBALE. 1 Set - 3 Nos R-Y-B Phase Indication Lamp with 6A MCB Protection. Automatic Transfer switch :The Automatic transfer switch should have complete switching neutral with zero position. 4 pole 415 v 50hz,Confirming to IS 13947 / IEC 60947. 01 nos of 200 Amp 4 P . Bus Bar: 300 Amp copper TPN Bus Bar covered with colour coded PVC Heat Shrinkable Busbar Insulation Sleeves, mounted on Porcelain/DMC/SMC Insulators. Outgoing: a) 03 No. - 63A, 4P MCCB Thermal Magnectic type, Icu = 25 kA ,Extended rotary operated mechanism b) 06 No.- 63A 4P MCB, Icu=10 kA Earth Bus Bar: 50 mm x 5 mm GI flat earth bus bar running along the base of the frame covering entire length of the panel with GI bolt and nuts and number of drilled holes as required for earth connection. Contractor should submit the GA Drawing of panel board and obtain necessary approval for authority before placing purchase P.O. of the panel board. 1 - Danger Board. Complete Board as stated above. [Non Schedule Item].CPRI approved.

LT PANEL for Marriage Hall and Auditorium area distribution Supply, testing, & commissioning of following type compartmentalised floor mounted cubicle board from 1.6 mm thick CRCA sheet dust and vermi proof duly phosphatized & powder coated 9 tank treatment. Incomer 01 for RAW POWER Input : 1 No. 150 A, 4P MCCB Microprocessor type with earth fault protection (Icu = 25 kA, Ics = 100% Icu) with extended rotary operated mechanism and O\L, S\C, G\F, E\F Releases with Panel door mounted Key lock for Extended ROM. Led type on, off & Trip indicating lamp. 1 Set (3 Nos) - 150/5A, 10 VA, Cl-1 Current Transformer. 1 Set - Cl-1 Multi Function Digital Meter with RS 485 BMS COMPATIBALE. 1 Set - 3 Nos R-Y-B Phase Indication Lamp with 1 Nos 6A TPN MCB Protection. Automatic Transfer switch :The Automatic transfer switch should have complete switching neutral with zero position. 4 pole 415 v 50hz,Confirming to IS 13947 / IEC 60947. 01 nos of 150 Amp 4 P . Bus Bar: 200 Amp copper TPN Bus Bar covered with colour coded PVC Heat Shrinkable Busbar Insulation Sleeves, mounted on Porcelain/DMC/SMC Insulators. Outgoing: a) 03 No. - 63A, 4P MCCB Thermal Magnectic type, Icu = 25 kA,Extended rotary operated mechanism c) 06 No.- 63A 4P MCB, Icu=10 kA Earth Bus Bar: 50 mm x 5 mm GI flat earth bus bar running along the base of the frame covering entire length of the panel with GI bolt and nuts and number of drilled holes as required for earth connection. Contractor should submit the GA Drawing of panel board and obtain necessary approval for authority before placing purchase P.O. of the panel board. 1 - Danger Board. Complete Board as stated above. [Non Schedule Item].CPRI approved.

Supplying including installation, testing and commissioning of Air/Water Cooled Diesel Generator set coupled to suitable alternator of 220/415 V, AC, 1/3-Phase 0.8 p.f. mounted on a 1) M.S. Fabricated base frame.,2) M.S. fuel tank of required capacity.,3) Residual Silencer.,4) Standard Control Panel.5) Suitable batteries with lead.,5) First fill of lube oil.,6) Acoustic Enclosure complete with all accessories as specified and directed by the department conforming to IS comprising the Technical Specification.. as per manufacturer. (RANGE FROM 5 KVA TO 625 KVA) Kirloskar green/bliss, Leyland, Volvo Penta, Perkinson, Mahindra, Greaves, Escort engine and Kirloskar, Stamford, Leroy somer alternator. 125 3 3200x1300x1805 2034 Kg W/C

DISTRIBUTION BOARD AND SWITCHGEAR Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer ) as required . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.) 8 way (4 + 24), Double door

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 8 way (4 + 24), Double door

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 12 way, Double Door

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts,10kA "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts,10kA "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts,10kA "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Double pole

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Triple Pole

Supplying and fixing of MCB Four Pole 415 V 63 Amps 10kA "C" curve in existing distribution board

Supplying and fixing of MCB Double Pole 25 Amps 10kA "C" curve in existing distribution board

Supplying and fixing of Residual current operated Circuit Breaker with Overcurrent protection (RCBO) Four Pole 415 V 63 Amps 300mA in existing distribution board.

Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required.

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/coke and salt as required.

Supplying and laying 6 SWG G.I. wire at 0.50 metre below ground level for conductor earth electrode, including connection/termination with GI thimble etc. as required.

Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.

Providing and fixing of lightning conductor finial, made of 25 mm dia 300 mm long, G.I. tube, having single prong at top, with 85 mm dia 6 mm thick G.I. base plate including holes etc. complete as required

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosurewith cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Supply of 1.1 kV grade XLPE insulated core laid up PVC tape innersheathed armoured aluminium cable of following rating, Confirming to IS : 7098 (Part-I),IS:8130-1984,IS:10810-1984,IS:10418-1982. 3.5C x 240 sq mm armoured cable.

Supply of 1.1 kV grade XLPE insulated core laid up PVC tape innersheathed armoured aluminium cable of following rating, Confirming to IS : 7098 (Part-I),IS:8130-1984,IS:10810-1984,IS:10418-1982. 3.5 C x 50 sq mm armoured cable.

Supply of 1.1 kV grade XLPE insulated core laid up PVC tape innersheathed armoured aluminium cable of following rating, Confirming to IS : 7098 (Part-I),IS:8130-1984,IS:10810-1984,IS:10418-1982. 3.5C x 95 sq mm armoured cable.

Supply of 1.1 kV grade PVC insulated core laid up PVC tape innersheathed armoured aluminium cable of following rating, Confirming to IS : 7098 (Part-I),IS:8130-1984,IS:10810-1984,IS:10418-1982. 3C x 4 sq mm armoured cable.

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe/Tray as required. Above 35 sq. mm and upto 95 sq. mm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe/Tray as required.

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required Above 185 sq. mm and upto 400 sq. mm

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV gradeas required.3½ X 50 sq. mm (35mm)

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV gradeas required3½ X 70 sq. mm (38mm)

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3½ X 240 sq. mm

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the ame in case of recessed conduit as required.20 mm

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the ame in case of recessed conduit as required.25 mm

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc. as required. Group B

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc. as required. Group C

Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required

Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point (without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required.Group B

Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point ( without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required.Group C

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 No 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed PVC conduit as required. 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed PVC conduit as required. 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed PVC conduit as required. 4 X 16 sq. mm + 2 X 6 sq. mm earth wire

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providng and fixing 2 nos. 3 pin 5/6 A modular socket outlet and 2 nos. 5/6 A modular switch,connections etc. as required. (For light plugs to be used in non residential buildings).

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required.

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.5/6 A switch

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.15/16 A switch

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.5/6 A (5 pin) socket outlet

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.6 pin 15/16 A socket outlet

Supplying and fixing following size/ modules, GI box along with modular base & cover plate for modular switches in recess etc as required. 1 or 2 Module (75mmX75mm)

Supplying and fixing following size/ modules, GI box along with modular base & cover plate for modular switches in recess etc as required. 3 Module (100mmX75mm

Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable etc. as required.

Supply of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CMM/W) minimum 6.85, Air delivery minimum 215 CMM, 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required.

Supply of ISI marked 300 mm sweep, 230 Volt AC Ring mounted Exhaust Fan including wire guard, louvers etc.

Supply of ISI marked 450 mm sweep, 230 Volt AC Ring mounted Exhaust Fan including wire guard, louvers etc.

Installation of exhaust fan in the existing opening, including making good the damage,connection, testing, commissioning etc. as required. (Upto 450 mm sweep)

Supply , Installation, testing and commissioning of 36W 2x2 6500 K LED Panel light luminaries with complete accessories as directed by the E-I-C

Supply , Installation, testing and commissioning of 20 W LED 6500 K Cool daylight white Recess Mounted Square/circle shaped luminaire with complete accessories as directed by the E-I-C

Supply , Installation, testing and commissioning of 20 W LED 4000 K Cool day white Surface Mounted circle/square luminarie with complete accessories as directed by the E-I-C

Supply , Installation, testing and commissioning of 20 W LED Tube light Cool day white with complete accessories as directed by the E-I-C

Supply , Installation, testing and commissioning of 22 W Cove LED warm white luminaire with complete accessories as directed by the E-I-C

Supply , Installation, testing and commissioning of 4000 K, IP 65 LED 15 W Post top lantern with all complete accessories as directed by the E-I-C

Supply , Installation, testing and commissioning of 5700K, IP 66 LED 70 W Street light with all complete accessories as directed by the E-I-C

Supply and fixing of Mild Steel 9 Meter Single Arm Street light pole with complete fittings including JB for street light luminaire connection as required by E.I.C

Supply, Installation, Testing & Commissioning of 9 W MIRROR light as directed by the E-I-C

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 300 mm width X 50 mm depth X 1.6 mm thickness

Supply, Installation, Testing & Commissioning of Machine room-less, eco-friendly regenerative drive technology, frequency controlled Elevator for 8 person car capacity , rated min load to be of 5440 kg, number of stops 05 with glass display ,travel speed 1.5 m/sec,one side entrance with all complete accessories as directed by the E-I-C,The price includes all required documents (i:e License ,etc) for operation of the elevator from the concerned authority

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 150 mm dia NB

80 mm dia NB

Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required : Single headed Stainless steel

Supplying and fixing orifice plate made out of 6 mm thick stainless steel (Grade 304) with orifice of required size to be fitted between flange & landing valve of external and internal hydrants to reduce pressure at the outlet to the level of 3.5 kg/cm2 complete as required.

Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red,conforming to IS 884 complete with the following as required. 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585 20 mm nominal internal dia gun metal globe valve & nozzle. Drum and brackets for fixing the equipmets on wall. Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket. 100 m

Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required :certification (Two per each single landing valve ). Stainless Steel (Grade 304)

Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required : Stainless Steel (Grade 304)

Providing and fixing standard fireman's axe with heavy insulated rubber handle tested for 20000 volts confirming to IS:926.

Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required : 2 way-100 mm dia M.S. Pipe

Providing ,Fixing ,Testing & Commissioning of air Release Valve a) 25 mm dia

Providing ,Fixing,Testing & Commissioning of G.M. Stop Valve ISI Marked screwed type tested to 30Kg/cm2 pressure as per IS:778-1984 of following sizes complete as reqd. 25mm dia full bore type

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : 100 mm dia

150 mm dia

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required : 100 mm dia

150 mm dia

INTERNAL SPRINKLER Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 150 mm dia

100 mm dia

80 mm dia

65 mm dia

50 mm dia

40 mm dia

32 mm dia

25 mm dia

Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories : Pendent Sprinkler

Upright Sprinkler

Providing, installation, testing & commissioning of adjustable rosette plate for 15mm dia in white finish UL Listed or FM approved complete as required.

Supplying, installation, testing & commissioning of sprinkler flexible pipe (UL Listed) of stainless steel complete with 15 NPT on reducer thread with maximum working pressure of 175 PSI test pressure of 875 PSI (Burst) with branch line (Inlet) 25mm NPT male thread to sprinkler head (Outlet) 15mm NPT female thread with reducer, nipple, 2 side brackets, center bracket, stockbar of following sizes complete as required. 1000 mm

Providing ,Fixing ,Testing & Commissioning of air Release Valve a) 25 mm dia

Providing ,Fixing,Testing & Commissioning of G.M. Stop Valve ISI Marked screwed type tested to 30Kg/cm2 pressure as per IS:778-1984 of following sizes complete as reqd. 25 mm dia

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : 150 mm dia

100 mm dia

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required : 150 mm dia

100 mm dia

Providing & fixing flow switch in following sizes M.S. pipe including connection etc as required. 150 mm dia

100 mm dia

EXTERNAL HYDRANT & RING MAIN Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 150 mm dia

80 mm dia

Providing and fixing ISI marked Single headed external yard hydrant valve 1 No. 63 mm dia instantaneous FM Gunmetal/Stainless steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290(Type A) with blank Gunmaetal /Stainless steel cap and chain a required. Single headed Stainless steel

Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required :certification (Two per each single landing valve). Stainless Steel (Grade 304)

Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required : Stainless Steel (Grade 304)

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : 150 mm dia

Providing & fixing of weather proof hose cabinets fabricated from 16 S.W.G. M.S. Sheet with centre opening full front glass door and locking arrangement, suitable to accommodate one landing valve (Yard Hydrant ), 2nos.15M long hoses and 1 no. Branch pipe with nozzle . The cabinet shall be painted with one coat of primer and 2 or more coats of synthetic enamel paint of approved make & shade and shall be suitably mounted on a raised masonry platform complete as reqd.(Make:self Fabricated) a) 900X600X450

Supplying & fixing of fire brigade connection of cast iron body with gunmetal male instantaneous inlet couplings complete with cap andchain as reqd.for suitable dia MS pipe connection conforming to IS 904 as required. 2 way-100 mm dia M.S pipe

PUMPS AND ACCESSORIES Supplying, installation, testing and commissioning of Electric driven Main Fire Pump suitable for automatic operation and consisting of following, complete in all respects, as required (a) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical seal conforming to IS 1520. (b) Suitable HP Squirrel cage induction motor, TEFC, synchronous speed 1500 RPM, suitable for operation on 415 volts, 3 phase 50 Hz, AC supply with IP 55 protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS-325. (c) M.S. fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. (d) Suitable cement concrete foundation duly plastered with anti vibration pads. 2280 lpm at 56 m Head

A)Supplying, installation, testing and commissioning of diesel engine driven main fire pump suitable for automatic operation and consisting of following, complete in all respects, as required : (Diesel Driven Pump) B)Horizontal type, multistage, centrifugal pump of cast of iron body and bronze impeller with stainless steel shaft, mechanical seal conforming to IS 1520. C)Suitable HP, 1500 RPM water cooled with radiator, diesel engine conforming to relevant IS standard complete with auto starting mechanism, 12 /24 volts electric starting equipment, diesel tank, exhaust pipe extended upto 10 m outside pump house duly insulated with 50 mm thick glass wool with 1.0 mm thick aluminium sheet cladding, residential silencer, instruments and protection as per standard specification, stop solenoid for auto stop in the event of fault with audio indications, painted with post office red colour etc. as required. D) M.S. fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. E)Suitable cement concrete foundation duly plastered with anti vibration pads. 2280 lpm at 56 m Head

(A)Supplying, installation, testing and commissioning of electric driven pressurisation pump suitable for automatic operation and consisting of following, complete in all respects, as required : (Jockey Pump) (B)Horizontal type, multistage, centrifugal pump of cast iron body and bronze impeller with stainless steel shaft, mechanical seal conforming to IS : 1520. (C)Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase 50 Hz AC supply with IP 55 class of protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS : 325. (D)M.S.fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. (E)Suitable cement concrete foundation duly plastered and with anti vibration pads. 180 lpm at 56 m Head

Supplying and fixing air vessel made of 250 mm dia, 8 mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and paintingwith synthetic enamel paint of approved shade as required.

Providing,erection testing & commissioning of pressure gauge 100 mm dia (0-10Kg/cm2)

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : a) 200 mm dia (wall thickness 6.3 mm)

b) 150 mm dia

c) 100 mm dia

d) 80 mm dia

Providing, erection testing, Commissioning of Cast Iron Foot Valve/Stainer confirming to IS:4038/1538 complete with flanges, nuts, bolts and washer etc as required 200 mm dia

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required : 150 mm dia

80 mm dia.

Providing and fixing MS structural work fabricated from standard sections, eg., MS rounds, angles, channels, inlcuding cutting to size, drilling, welding, fixing and welding to insert plates in RCC structural memebers as directed by the engineer-in-charge including cutting and making good the walls and floors (for Pipe Support Structures & Cable tray.)

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : 200 mm dia with lever

150mm dia with lever

80mm dia with lever

Providing ,Fixing,Testing & Commissioning of G.M. Stop Valve ISI Marked screwed type tested to 30Kg/cm2 pressure as per IS:778-1984 of following sizes complete as reqd. 25 mm dia

Providing & fixing of pressure switch in M.S. pipe line including connection etc. as required.

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps

Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS :2556, C.I. trap with outlet grating and other couplings in C.P. brass,including painting of fittings and cutting and making good the walls and floors wherever required : Single f stall urinals with 5 litre P.V.C. automatic flushing cistern

Range of three half stall urinals with 10 litre P.V.C. automatic flushing cistern

Receiving and fixing following Chrome Plated Fittings complete with required accessories including cutting and making good the walls wherever required to compete the work functionally and asthetically as directed by the consultnat: Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 15 mm nominal bore

Sink Cock (only cold water) )Jaquar make Model No-CON-357KN)

Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge.

Providing, fitting and fixing Chrome Plated waste coupling complete as directed and specified (a) Jaquar Make (i) 32mm (HT/FT) (Cat.No.ALD-705 / 709)

Providing, fitting and fixing Chrome Plated towel ring complete as directed and specified. (a) Jaquar make (i) Continental towel ring square (Cat.No. ACN-1121)

Providing and fixing toilet paper holder C.P brass

Providing, fitting and fixing Liquid soap dispenser and liquid soap container complete as directed and specified. (i) Jaquar Make (a) Continental (Cat.No.ACN-1135N) (with glass bottle)

Providing, fitting and fixing Chrome Plated robe hook complete as directed and specified. (i) Continental (Cat.No. ACN-1191N)

2way bib cock for W.C(Jaquar Make CON-041KN)

Health Faucet(Jaquar ALD-565)

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : Kitchen sink with drain board 510x1040 mm bowl depth 250 mm

SUB - HEAD - II : INTERNAL DRAINAGE (SOIL, WASTE, VENT & R.W. PIPES) Supplying, fitting and fixing PVC pipes of 6 Kg/cm2 (Supreme/Prince) or other ISI approved including joining ,fitting and fixing wiyh clamps etc.as necessary complete at all levels including below G.L as directed and specified. b) Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages. 50mm dia

75mm dia

110mm dia

Supplying, fitting and fixing PVC pipes of 6 Kg/cm2 (Supreme/Prince) or other ISI approved including joining ,fitting and fixing wiyh clamps etc.as necessary complete at all levels including below G.L as directed and specified. a) In exposed surfaces or in trenches. ii)110mm dia

Providing fiting & fixing C.I. Grating to the floors complete as directed and specified. (a) 110mm dia

Providing and fixing SS floor clean out plug comprising of uPVC pipe, socket, elbow, extension piece caulked to pipe , complete as required. For 100 mm dia pipe

Providing and fixing in position Multi Function floor trap of the following sizes as per drawings with min 50 mm water seal ( No of inlet connections as per site condition ) including providing necessary support and as per Specification and duly epoxy coated. Making proper connection with dripseal joints, cutting chase / hole in floors / slabs and bringing the same in proper condition and shape after placing the trap in right position complete by supporting by clamps / hangers as required. 110 mm, including riser if needed, Deep 50mm Seal P Trap with riser and inlet connections including core cutting & sealing with non shrink grout and epoxy

COLD WATER SUPPLY (INTERNAL) Providing and fixing Chlorinated Polyvinyle Chloride (CPVC) Pipes, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings i/c fixing the pipe with clamps at 1.00m spacing. This includes jointing of pipe (B) Concealed pipe with cutting chases & making good the walls a)15 mm nominal outer dia Pipes

b)20 mm nominal outer dia Pipes

c)25 mm nominal outer dia Pipes

d)32 mm nominal outer dia Pipes

e)40 mm nominal outer dia Pipes

Providing and fixing SCHEDULE 40 UPVC (Unplasticized Poly Vinyl Chloride) cold water supply and treated water supply water supply pipes as per As per ASTM D1785, D2467, WITH fittings i.e Tees, Elbows, Couplers, Unions, Reducers, brushings etc. including transition fittings cconnection between CPVC & UPVC i.e Brass Adaptors (both Male & Female threaded) conforming to ASTM D-2846(upto 50mm dia.)/ASTM F-438 (65mm & above dia. pipe) with only CPVC solvent cement conforming to ASTM F-493 including cutting chasing and fixing the same with cement concrete / cement mortar as required, including painting the exposed pipes with one coat of desired shade of enamel paint. All termination points for installation of faucets shall have brass termination fittings. Installation shall be to the satisfaction of PMC / Consultant / manufacturer of pipes & fittings. Pipes in the Shaft will be fixed using hot dipped galvanized fixing channels & GI U Clamps with proper rubber gaskets 80 mm nominal outer dia Pipes

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 25 mm nominal bore

Supplying and fitting gun metal country pit valve (full way valve) I.S.I. Make as specified and directed. b) 40 mm dia.

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 32 mm nominal bore

32 mm nominal bore

Providing and fixing Auto Air Purge Valve with screwed ends of approved quality. 15mm dia

Supplying fitting and fixing gun metal check valve including necessary threads to pipes. a) 50 mm dia (Heavy type)

a) 40 mm dia (Heavy type)

Providing & fixing CI butterfly valve (upto 150mm dia with hand lever operation & above with gear box operation). Tested to a pressure not less than 16 Kg/Sq.cm. Including rubber gasket, flanges, nuts, bolts, washers & painting complete as required. 65 mm nominal bore

EXTERNAL SEWAGE / STORM WATER DRAINAGE Supply & Fixing of in Double wall corrugated (DWC) pipes SN8 for non pressure underground drainage and sewerage with smooth internal & corrugated external surface confirming to IS:16098 with spigot or plain end with necessary jointing material coupler including rubber ring joints all transportation and freight charges, inspection charges, loading and unloading charges transportation to departmental store/site and stacking the same in in closed shade duly protecting from direct sun ray and rains etc. complete. The cost will include all cost towards consumabes, labour etc complete in all respect. 150 mm dia (SN8)

100 mm dia (SN8)

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating, brick masonry chamber with water tight C.I. cover with frame of 300x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design:. 180x150 mm size P type With common burnt clay F.P.S.(non modular) bricks of class designation 7.5

Constructing brick masonry manhole in cement mortar 1:4 (1 cement: 4 coarse sand )with R.C.C top slab with 1:2:4 mix (1 cement:2 coarse sand: 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement: 4 coarse sand: 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement: 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement: 2 coarse sand:4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design: Inside size 90x80 cm and 45 cm deep including C.I cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg): With common burnt clay F.P.S (NON modular) bricks of class designation 7.5

Extra for depth for manholes : Size 90x80 cm With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

PUMPS Supply & commissioning of horizontal/ vertical openwell submersible pump for water transfer with CI impeller and SS/CI motor body. Filter Feed pump cum overhead lift pump Capacity : 1 LPS Head : 35 Mtr (Head to be reaffirmed by vendor as per site inspection)

Supplying and placing Ferrocement Iron Removal Plant over stagging with movabale G.I. Sheet cover with side ventilation including providing pads of size as required for inlet and outlet pipes complete as directed.(Stagging and storage reservoir should be measured and paid separately). 1000 lt capacity

Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer -in-charge, beyond 90 metre & upto 150 metre depth below ground level. 300 mm dia

Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charg 23.4.2 200 mm nominal size dia

Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.

Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by "V" notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge

Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of: 23.13.3 200 mm dia

Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete. 23.14.3 200 mm clamp

Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS:2800 (part I). 23.15.3 200 mm dia

WATER TANK Supplying and placing plastic cylindrical vertical claused top (PCVC) tank of Sintex / Polycon / Patton make over the stagging with manhole cover with locking and cleaning arrangement including providing pads of size as required for inlet and outlet pipes 2000 Lt capacity (a) Sintex make

Lighting Fixtures: SITC of LED 'ELF' PAR, RGBW: 180w Pro-series using 60x 3w -1 LEDs ; Powercon connectors for IN & OUT ; DMX-512 signal, 6/9 DMX Channels ; Beam Angle 30 degrees Al. die-cast housing ; s/w suitable clamp (Make: NSC - Model : LP-603

Supply, installation, testing & Commissioning of LED Fersnal light with Lamp : High quality 200W LED Fresnel light used as a Key light, Back light, Fill light with dimming, spot & flood focus versions for creating various effects for multiple applications with specifications as below. Lamp power - 200W COB LED Power supply - 100-240 AC, 50/60 Hz Power cable - 3 core 1 sq. mm. copper PVC insulated Color Temperature: 3200K Control : DMX512 / Manual Spot - Flood focus adjustment. Complete in all respect as desierd by the Engineer in charge of work at site. Approved Model : LFS-200

Supply, Installation, Testing & Commissioning of LED profile 300w 36* voltage0-90-250v/50-60hz,working position: Any safe working position ,lamp: super high power LEDs; white 180w (cool white or warm white) average life time is over 5000h,CRI:>90,Lens angle :19*/26*/36*,optinal, LED display channel-2 ch,IP rate :IP 20 indor, speacial zoom funcation with manual adjustment, control mode: master /slave synchronization,DMX 512 control and automatic, run, construction: die-casting aluminum housing silver white and black,optinal of Model : LPRO-300

SITC of LED PAR with Lamp : 240W warm white LED, (50,000 hrs), Voltage: AC90-260V 50/60Hz, Power consumption: 200W, Dimmer: 0100% electronic dimming, High speed strobe effect with 4 default strobe modes and speed adjustable, Hight light output with pure and even coverage, Light angle: 60°(8083A/ B/C/D), 120°(8083K/L), Control: DMX512, master-slave and sound activated or auto operation, Channels: 3/5/7(8083A), 5(8083D),3(8083B/C/L), 5/7/8(8083K)DMX channels USITT DMX-512, LED display, Low noise and efficient etc as required.make: NSC Model :LPW-803

SITC of LED FOLLOW SPOT Light (compact): Long throw ; using Hi-Power 150w LED ; On- board Manual Controls for Dimmer, Iris, Colors & CT Correction Filters ; IP-20 rated ; Power AC 240V / 50Hz 165W ; Lamp Life: >50000 hours ; supplied with Folding Stand ; Modal ; 10R

SITC of LED SPOT 280 Moving Head : using 400W single white LED lamp ; 12° to 36° linear motorized zoom ; rotatable gobo wheel (7 gobos plus open) ; static gobo wheel (9 gobos plus open) ; color wheel (7 colors plus open) ; motorized linear IRIS ; 3-facet rotating prism ; variable frost filter ; motorized linear focus ; 0-100% linear LED dimmer ; variable speed shutter/strobe ; Control Channel: 15 / 17 DMX channels ; Power Consumption: 400W ; MAKE PRO ,NSC

SITC of Smoke Machine: 3000w ; DMX operated

Light Bars & Wiring SITC of MS pipe Side Light "Ladder" brackets : with 3-sections, to be provided on either sides for Side Lights - using 1.5" square MS Tube ; to be fixed from the existing main structure Girder / Grid / Beams / Ceiling ; approx. size: 600 mm.x 600mm. ; duly painted black

SITC of WIRING for DMX Points: using .07 sqmm falcon FR wire with common xlr .

SITC of WIRING for DIRECT Points: using 1.5 sqmm FINOLEX FRP wire with common neutral & earth for 2 sockets starting from the patch panel (side of stage) to the Lighting bars/tree or stage points ; terminated at junction box with 2 x 3- pin CEE 16 Amp. modular sockets ; cabling laid in PVC conduits .STAGE TO STAGE

SITC of MS pipe Lighting Bar (fixed): to be provided at FOH position - to be fixed from the existing main structure Girder / Grid / Beams / Ceiling, ; approx. size 12m x 50mm dia B-class,MS PIPE supported by A.I. brackets ; duly painted black

SITC of MS pipe Lighting Bar (fixed): to be provided at FOH position - to be fixed from the existing main structure Girder / Grid / Beams / Ceiling, ; approx. size 12m x 50mm dia B-class,MS PIPE supported by A.I. brackets ; duly painted black

DMX & Controls: SITC of Pearl-2410 DMX Lighting Desk : 240 Intelligent Fixtures + 240 Dimmer Channels ; 2410 Channels ; Load and Save shows with USB ; Theatrical Plotting & Playback functions ; Shape Generator ; 15 Playback Masters controlling 450 memories, chases or cue lists MIDI and Sound to Light triggers ; VGA output ; supplied with LEd lamp

SITC of DMX Data Splitter: 1 x IN to 8 x OUTPUT DMX-512 Data Splitter Unit, suitable both for Dimmer & Intelligent Lights ; Model: SP-81

SITC of Inter connection - DMX Data patch cables, for interlinking Intelligent Lighting Fix

STAGE Craft SITC of MAIN CURTAIN made out of velvet ( INOVATIV/ Vimal/Relince) Main curtain made out of Velvet curtain cloth with Vertical sliding arrangement complete with fixing railing rack,fixing brackets,pully,drum,2mm rope wire,1HP Crompton/Godrej Motor,drum with groove cutting,pulleys,2 No air bracker switch(L&T,Siemens,GE make) for up & down,2 No air microswitch for auto stop,3 No push button for Open/Stop/Close position the curtain should be droped up down and curtain should be stitched in one dubale gathering.Complete in all respect and to be approved by Architect and his representative. Appx. Size:-13500 mm X 8000mm

SITC of REAR CURTAIN made out of black colour crepe/galaze cloth with horizontal sliding arrangement complete with fixing rails, brackets, sliding arrangements & motorised operation complete with runners, master runners, pullies, 3mm steel wire rope, 1HP motor (Crompton/GODREJ) 2nos. air breaker contactors (L&T/SIEMENS), 2 nos. micro switches for auto stop, 3nos. push buttons for forward, reverse and stop positions. The curtain should be draped to half area when in closed position. Minimum overlap at centre should be 900mm and should be stitched in double gathering. size 13500mm X 8000mm

SITC of SIDE WINGS Providing and fixing cloth wings made out of black glazed cotton cloth) with fixed on both side of MS 50mm x 25mmx 16G pipe wielded frame work. The pipe framework made out of 25mm x 50 mm pipe. c/c 600 x 600 fixed with overhead pivote track complete with duly painted on both framework. Size :1200mm x7000mm Customized

SITC OF FRILLS Providing and fixing average frills made out of double gathering glazed cotton to be installed above the stage on 28mm diams pipe. Size: 14000MM (AV) x 1800MM

SITC OF MS GRID Supplying fabricating and installing structural grid fabricated out of MS PIPE/40mmx40mmx5mm (NS) MS angle above stage for supplying light bars. Curtains wing set bar sets. suspending the structure from trusses with suitable size of MS 35x35x5/ flat 35x5

Brick work in cement mortar with 1st class brick including racking out joints and dewatering if necessary and curing complete as directed in sub structure upto plinth level. a) In prop 1:4

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. Cement mortar 1:4 (1 cement :4 coarse sand)

52 mm thick cement concrete flooring with concrete hardener topping, under layer 40 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) and top layer 12 mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate 6 mm nominal size) by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per manufacturer's specifications. This includes cost of cement slurry, but excluding the cost of nosing of steps etc. complete.

SONODYNE Main speaker Passive Line Array SJX 1210 Dual 10" line array, 800 watt AES, 8 Ohm

SONODYNE Truss Head SJX TH10 Truss head for SJX 1210

SONODYNE Power Amplifier SLA 3010 Class H power amp 1500 x 2, 4 Ohm, 2 ohm operation

SONODYNE Sub Woofer SLX 2182 2 x 18" Subwoofer with 5" VC, 2600 watt AES, 5200 watt program, 4 Ohm, front firing

SONODYNE Power Amplifier SLA 3013 Class H power amp 2000 x 2, 4 Ohm, 2 ohm operation

SONODYNE Sub Woofer SLX C1 Subwoofer Controller with subsonic filer, variable LPF, and gain

SONODYNE Surround Speaker SLX 1010 10" LF with 2" VC, HF with 1" VC, 200 watt AES, 400 watt program, 8 Ohm

SONODYNE Power Amplifier SLA 3004 Class AB power amp 600 x 2, 4 Ohm, 2 ohm operation

HARMAN DBX PA2 Audio Digital loudspeaker manager including 2 audio inputs and 6 audio outputs electronically balanced, 24 bits-48 KHz , USB interface and 2 volume remote control ports (0-10VDC), full DSP, labels edition, password protected, system templates, 20 presets. Fully configurable from PC via control software.

SONODYNE Stage Monitor SPA 115P Biamped : rms: 350, program 700 watt, 15"LF + HLCD

SONODYNE Equaliser SSP 2025 Dual channel 31 band graphic EQ with limiter and NR, 2 RU

SONODYNE Mixer SMX 1124 24 channel mixer with 20 mic/line, 2 stereo line, 4 aux, 2 subgroup, graphic EQ, DSP effects, mp3, BT, mp3 recording

Professional Wireless Handheld Microphone Make : Sennheiser

Professional Wireless Lapel Microphone Make : Sennheiser

Professional Audio cable and Connector

Side Speaker Wall Mount Bracket

Sound Processor Model ;SEQ 302 f

High-performance dynamic vocal microphone Heavy-duty metal body to withstand tough stage performances. An integrated windscreen efficiently eliminates pop and wind noise. Audio frequency bandwidth40 - 20000 Hz,Sensitivity2.5 mV/Pa,Electrical impedance580 Ohms,Recommended load impedance2000 Ohms,

PA Microphone Stand

42 U Interconnected Network Rack Networking Equipment Rack APW President Enclosure, 600mmW CYBERACK 42U/800mmD (CRCA Steel Frame with Aluminium Profiles & 2 Nos. of Removable Side Panels with followwing items:- Top cover with cable entry-1no.-Bottom cover with cable entry-1no.-19" Mounting Angles-2 pairs., Finish: Powder coated to 80 microns; Matt Finish. Colour: BLACK with, Load rating capacity -500 Kgs., Front side vented glass door and rear full perforated steel door with locks. " PDU 10*5/15A-01 Nos., Fan Housing Unit with 4 Fans-01 Set, Mounting Hardware (Set of 20)-1 Set, Castor with Brake 2Nos., Castor without Brake - 2 Nos., Earthing Kit - 01 Set, Cable Manager 19" 1U - 2 Nos

Professional Signal Cable

14 AWG 2 Core Speaker Cable and Cabling Condute

CP Block II 3M with Snap hook

Chain 6MM

Customized stage mic pocket box

SERVICE: Installation, Testing, Configuration, Commissioning & Professional Engineering Charges

SITC OF AUDITORIUM CHAIR SITC OF AUDITORIUM CHAIR Model: Venus Made up of Moulded PU foam, density 45+/-5 density. Tubular steel structure for stand 80 x 40 x1.6mm. Metal frame for back frame(25 x 3mm m.s. flat) Metal frame for seat frame(20 x 3 mm m.s.flat) 1 PPCP plastic tray for seat & back cover. Wooden polish arm rest without cup holder. PPCP plastic side panel with upholstered fabric.Laminated Fabric, Foldable metal mechanism fitting expandable anchor fastners of size: M 8 x 75 mm, with writing desk. Auto tip up Mechanism with sharing arms. Make: Cine

SITC OF Floor carpet Nylon Loop Pile carpet of 600 GSM with 4mtr. With underlay of 6mm PU -1835200

Double bed( 1.8m x 1.9m)

Single bed ( 1.2mx 1,9m)

Side table .6mx ,6mx .45m

Luggage rack 1.Sm x .6m x.75m

Wardrobe ( l.2m x2mx .6m

Service table (O .8mx 0.8mx0.5m)

TV Panel with working table 2.4mx .45m

Spring Mattress for Beds 10 "thick l.2m xl.8m

Spring Mattress for Beds 10 "thick 1.8m xl.8m

VERSHA TECHNOTRADE PVT LTD (BID ID -230922)

Ganesh Daimary (BID ID -230792)