REPAIR TO ROOF JOINERY FLOOR PLUMBING SANITARY FITTINGS INCLUDING MISC EM WORKS TO CERTAIN BLDGS AT KALINGA DWAR UNDER GE I GOS

Amount

Taking down chowkhats with shutters (without taking off shutters from the frame) not exc. 1.5sqm each complete all as specified & directed.

Taking down chowkhats with shutters (without taking off shutters from the frame) exc. 1.5sqm but.not exc. 4 sqm each complete all as specified & directed.

Taking down shutters of any description not exc. 1 sq.m each. complete all as specified & directed.

Taking down shutters of any description exc. 1 sq.m not exc. 2 sq.m each. complete all as specified & directed.

S&F 2nd class Hard wood in plain, solid, straight chowkats and frames wrought framed, rebated on the solid, rounded or chamfered put together with glue pinned joints and fixed complete all as specified and directed.

S&F Bands, straps, clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe -290 Gde E-165 complete all as specified and directed.

M&L PCC 1:3:6 type C1 using 20mm graded stone aggregate for fixing of hold fast and making good complete all as specified and directed.

S&F solid PVC door frame of size 50mm X 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tubes, as per specifications and drawing complete all as specified and directed.

S&F for Factory made solid panel PVC door shutter 30mm thick (Style) consisting of frame made out of MS Tubes for top & bottom rails M.S frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement of stiles and plain colour PVC Sheets for top rails lock rail & bottom rail on eighter side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in the M.S frame welded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement , suppling & fixing in the frame at site complete and all as specified and directed.

S & F 40 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides to match complete all as specified and directed.

S&F 30mm thick 2nd class hard wood Glazed and skelton shutter, open rebated and prepared to receive glass, gauge etc. devided into squares with plain chamfered or rounded, mitred and rebated sash bars edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc. sizes of members of shutters as specified in SSR Part-I Section-8 clause 8.23(b) complete all as specified and directed.

S&F 35mm thick 2nd class hard wood plain framed panelled shutters (two panels) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces.The size of rail and stile as per IS:1003 (Part1),kiln seasoned and chemically pressure treated,complete all as specified and directed.

S&F 100mm size butt hinges extruded aluminium alloy with alloy with galvanised mild steel hinge pin, complete all as specified and directed.

S&F 75mm size butt hinges medium weight (ISI Marked), extruded aluminium alloy with galvanised mild steel hinge pin,anodised and fixed, type-C21 complete all as specified and directed.

S&F 150mm size extruded aluminium alloy handles, fabricated type anodized complete all as specified and directed.

S&F 100mm size extruded aluminium alloy handles, fabricated type anodized complete all as specified and directed.

S&F in repair 150mm size extruded aluminium alloy handles, fabricated type anodized complete all as specified and directed.

S&F 150mm size Aluminium anodized barrel Tower bolts of extruded section and fixed complete all as specified and directed.

S&F 100mm size Aluminium anodized barrel Tower bolts of extruded section and fixed complete all as specified and directed.

S&F in repair 150mm size Aluminium anodized barrel Tower bolts of extruded section and fixed complete all as specified and directed.

S&F Aluminium alloy, anodized, sliding door bolt (ISI Marked) of 300mm with hasp & staple (Bolt type) and fixing clips of sheets, coat or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed.

M&L preparation of new wooden surface exc 10cm width or girth and applying two coat of synthetic enamel paint over one coat of pink primer complete all as specified and directed.

S&F 2nd class hardwood Beads, straight (any size) for glazed or gauzed joinery, renewed, including mitres etc., and removing old beads to Store complete all as specified and directed.

S&F aluminium alloy wire cloth, 0.45 mm nominal dia of wire and averaging width of aperture 1.40mm and fixed with aluminium wire staples complete all as specified and directed.

S&F in repair aluminium alloy wire cloth, 0.45 mm nominal dia of wire and averaging width of aperture 1.40mm and fixed with aluminium wire staples complete all as specified and directed.

S& F in repair double action door floor spring Hydraulically regulated made up of Min 1.25 mm thick aluminium alloy sheet foundation Box Main Body with stainless steel cover governing Pivot made of brass, other parts made of mild heavy duty and fixed etc complete all as specified and directed. make : SINDHU/SAMARAT.

S& F in repair Aluminium (extruded section) body Door closer hydraulically regulated, designation No. 1 universal type, suitable for door shutters up to 700 mm in width and of weight not more than 35 kg and fixed complete all as specified and directed.

S&F 300 mm long mild steel ordinary rat tail rod pattern springs including roller and roller plate, ISI marked complete all as specified and directed.

S&F Mild steel framed work such as in grills, grating etc. with ends of bars shouldered and/or riveted or forged into spikes, framed guard bars, conforming to Fe-410-0 or Fe-310-0.

M&L preparation of new steel surfaces of any description not exc 10 cm width or girth and priming with red oxide zinc chrome and painting with two coats of synthetic enamel paint complete all as specified and directed.

Hacking out old broken glass panes of any thickness, size ,quality or description from wooden frames, aluminium frame glazed with putty or fixed with beads in repairs complete all as specified and directed.

S&F glass pan ordinary quality 3mm thick and glazing with oil putty/ wooden beads in square n. exc 0.5 m each pane complete all as specified and directed.

S&F in repair vitreous china wash basin, white flat back size 580mmx450mm, excludings taps, waste, chain and plug and porcelain stopper but including brackets, complete all as specified and directed.

S&F in repair vitreous china squatting pan Orissa pattern size 580 x 440 mm white with internal footrest (excluding flushing cistern and flush pipe) complete all as specified and directed.

S&F in repair Vitreous china bowl type Urinal flat back ,size 465x355x265 with grating and Union for discharge pipe including all necessary items complete all as specified and directed.

S&F in repairs Vitreous china wash down water closed pan ( Pedestal) white (exc flushing cistern & Pipe ) incl connection to trap and flushing pipe complete all as specified and directed.

S&F in repair PVC low level flushing cistern (white) 10 Ltrs capacity with internal fitting, push button operated type with and including bracket, PVC flush pipe etc complete all as specified and directed.

S&F in repair sink with draining board made out of stainless steel 1.00 mm thick sheet for kitchen with plugs, washers and wastes including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm with bowl size 410 mm x 330mm x 160mm complete all as specified and directed.

S&F 1 mm thick stainless steel plate rack of size 900x600x200mm including fixing with rawal plug ang screws complete all as specified and directed Make Blue Star cat No kpr - 313/ kpr- 314 or equivalent of nirali/ parryware.

S&F tubular towel rail aluminium anodised 20 mm dia D-type 60 cm long between flanges, including brackets and fixed to walls complete all as specified and directed.

S&F in repair Chromium plated brass shower rose75 mm dia with swivel joints, complete all as specified and directed.

S&F in repair angle valve 15mm bore brass chromium plated with captan head screwed for iron pipe, complete all as specified and directed.

S& F in repairs CP Jt Spray/Health faucet with 1.5 mtr 15mm bore PVC Tube and hooke complete all as specified and directed. MAKE : JOHNSON/JAGUAR ESSCO CAT NO -547

S & F in repair coloured EWC sheet cover complete all as specified and directed. make= Parry ware cat part No C 8012 or equivalent of specified make.

S & F in repairs grating doom 125mm dia with waste hole of PTMT fixed on floor/nahani trap with cement mortar, complete all as specified and directed. (Minimum weight 40 gms) .

S & F in repairs PVC waste pipe 32mm dia, 60 cm long for WHB with cup, complete all as specified and directed.

All as per Item No 47 above but 40mm dia for sink complete all as specified and directed.

S & F in repairs Stainless steel waste coupling for S.S Sink 75mm to 100mm dia set with rubber washer plug etc complete all as specified and directed.

S&Fin repair PVC connection 15 mm size, of length 450 mm, with PTMT nuts complete all as specified and directed.

Taking up or down steel water tubing and connections of following descriptions :- (a) 15 mm bore

(b) 20 mm bore

(c) 25 mm bore

Supply and laying CPVC pipes SDR 11 & Plain CPVC 11 fitting on walls/ceiling or laying in floor complete all as specified of following descriptions :- (a) 16 mm outer dia

(b) 20 mm outer dia

(c) 25 mm outer dia

All as per item no.54 above but re-fixing of old steel tubing of following descriptions:- (a) 15 mm bore

(b) 20 mm bore

(c) 25 mm bore

S&F CPVC Brass Elbow (a) 16 mm outer dia

(b) 20 mm outer dia

S&F CPVC Brass Elbow (3/4 x1/2) 20 mm outer dia

S&F CPVC Brass Tee (a) 16 mm outer dia

(b) 20 mm outer dia

S&F CPVC Male Brass Threaded Adaptor (MTA/MBTA) (a) 16 mm outer dia

(b) 20 mm outer dia

S&F CPVC Female Brass Threaded Adaptor (FTA/FBTA) (a) 16 mm outer dia

(b) 20 mm outer dia

S&F CPVC Tank adaptor 20 mm outer dia

S&F CPVC Union (a) 16 mm outer dia

(b) 20 mm outer dia

S&F Lid (cover) of Rotational moulded polythelylene water storage tank capacity 500/1000 ltr complete all as specified and directed.

S&F in repair ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe of 15 mm bore (minimum weight 142 gms), complete all as specified and directed.

S&F in repair ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe of 20 mm bore (minimum weight 210 gms), complete all as specified and directed.

S&F in repairs gun metal globe or gate valve with iron wheel screwed both ends for iron pipe of 20 mm dia complete all as specified and directed.

S&F in repair 15 mm fancy type pillar taps chromium plated cast copper alloy with capstan heads screwed down high pressure with or without lettered ‘Hot’ or ‘cold’ with long screwed shanks and fly nuts. complete all as specified and directed.

S&F in repair 15 mm fancy type stop valve cast copper alloy chromium plated screwed down high pressure with crutch or butter fly handle screwed both ends for iron or union and fixed to 15 mm GI tube complete all as specified and directed.

S&F in repair 15mm bore bib tap cast copper alloy chromium plated with crutch or butterfly handle fixed to 15 mm dia GI tube complete all as specified and directed.

S&F in repair Wall mixer with provn for over head shower with 115mm long bend pipe on upper side connecting legs,& wall falnges, complete all as specified and directed. Make : Jaquar Code No - CQT - 23273UPR

S&F in repair sheet glass shelf assembly consinsting of 5.5 mm thick sheet glass shelf 12 CM wide with CP bracket guard and railing 60 cm long complete all as specified and directed.

Demolition of Cement concerte (unreinforced) in ground floor and paving n exc 15 cm thickness below or above ground level complete all as specified and directed.

M&L 75 mm thick PCC 1:3:6 type C2,using (40 mm graded stone aggregate ) laid as in plinth protection/paving etc finished even & smooth with out usnig extra cement complete all as specified and directed.

M&L for 100 mm thick cement concrete 1:2:4 type B2 using 40 mm graded stone aggregate as in hard standing surface finished even and smooth with out using extra cement complete all as specified and directed.

M&L 25 mm thick PCC (1:2:4) type B0, (12.5mm graded aggregate) finishing cement concrete surface even and smooth without using extra cement complete all as specified and directed.

Dismantling floor, heart or wall tiling including cement mortar bedding complete all as specified & directed.

M&L for glazed ceramic tiles in vertical surface 350x250x7mm/450 x350 x 7 mm thick coloured on vertical surfaces such as dado/skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match , including 15mm thick screed bed in CM 1 :4 complete all as specified and directed.

M&L for Non Skid ceramic tiles 7 to 8 mm thick(square/ rectagular) area of each tile exceeding 0.11 sq m but not exceeding 0.18 sqm , in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match , including 15mm thick screed bed in CM 1 :4 complete all as specified and directed.

All as per item No 88 above but on skirting.

M&l Vitrified Ceramic tiles 10 mm thick (square/ rectagular) dark/colour shade polished,area of each tiles not exceeding 0.36 sqm , in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match as in floors over 20mm thick screed bed in CM 1:6 complete all as specified and directed.

All as per item no.90 above but on vertical surface of wall of size 600x100x10mm thick as in dado/skitting including 10 mm thick rendering in CM 1:4 complete all as specified and directed.

Taking down cement plaster of any description including raking out joints, hackisng for key, scrubbing down with water etc.complete all as specified and directed.

M&L rendering 15 mm thick plaster in cement mortar 1:4 on fair faces of brick work or concrete surface of wall and finiceshed even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 10 mm thick plaster in cement mortar 1:4 on fair faces of brick work or concrete surface of ceiling/chajjas etc and finished even and smooth without using extra cement complete all as specified and directed.

M&L rendering 5 mm thick in cement and sand mortar 1:4 on concrete surfaces of ceiling including finishing the surface even and smooth without using extra cement complete all as specified and directed.

M&L preparation of newly plastered surfaces of walls and applying three coats of white wash complete all as specified and directed.

All as per Item No. 8 above but on ceiling

M&L for preparation of new plastered surface and applying two coats of oil bound distemper over a coat of chalk whiting putty complete all as specified and directed.

M&L for preparation of new plastered or unplastered surfaces of wall including removal of vegetation and applying two coat of cement based paint complete all as specified and directed.

Taking down existing water proofing membrance and cleaning roof, plastered surface etc preparing the surface to receive plaster by brushing with wire brush and fanning the surface to remove all loose dirt etc and brushing neat cement slurry @ 3.00 Kg/Sqm complete all as specified and directed.

M&L for rendering 15 mm thick surface as in roof with integral water proofing compound 3% by the weight of cement in cement mortar 1:4 complete all as specified & directed. (Integral WPC will be measured and paid separately).

Supply only Integral waterproofing compound.

M&L for water proofing treatment to roof surface complete all as specified & directed with the followings :- (a) Apply bituminous based primer confirming to IS: 3384-1965 @ 0.30 kg/sqm. (b) APP modified bituminous membrane 3mm thick with non woven polyester core of weight not less than 3.2 to 3.5 Kg/sqm laid and bonded to the sub strata by heat process, over laps of 100mm shall be sealed/fused by flame torch application as per manufacturer instructions. (c) Applying bituminous based aluminium paint @ 0.20 Kgs/Sqm in two coats over APP membrane.

Dismantling PVC water storage tanks exc 500 ltr but n. exc 1000 ltr capacity and removing to store complete all as specified and directed.

Dismantling PVC water storage tanks exc 1000 ltr but n. exc 2000 ltr capacity and removing to store complete all as specified and directed.

S&F 500 ltr capacity Rotational moulded polyethylene water storage tanks (cylin-drical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I.

S&F 1000 ltr capacity Rotational moulded polyethylene water storage tanks (cylin-drical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I.

S&F in repair cast iron waste and vent pipe in any length with or without ear with cement joints, fixed to walls for 100mm bore complete all as specified and directed.

All as per item No 109 above but 75mm bore

S&F in repair cast iron bend ( any radius) dimenshing pieces or tappers ( large bore measured) 100mm bore with oval access door complete all as specified and directed.

All as per item No.111 above but 75 mm bore

S&F 110mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls complete all as specified and directed.

S&F 110mm bore PVC (SWR) bends any radius

S&F 75mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls complete all as specified and directed.

S&F 75mm bore PVC (SWR) bends any radius

S&F PVC (SWR) cowl of 110 mm dia

S&F anodised aluminium glazed side hung double/single door shutters with anodised aluminium frame of section 100x44x 2.00mm and shutter having style, top rail, lock rail and bottom rail of 44.5X99X1.8mm including 5.5mm thick tinted sheet glass ordinary quality with all necessary suitable push & pull plate/handle, screw, jointing cleats, rubber packing, aluminium snap beading and 1 No 200mm long Al tower bolt, 100 msm long 3 No Al butt hinges B-21 type, and one No mortice brass lock 100mm size 4 leaver (vertical type) with double action floor spring hydraulically regulated made up of min 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavey duty (Make Sindhu /Samrat) for each shutters complete all as specified and directed.

S&F aluminium anodised galzed hung type window shutters made out from anodised aluminium frame of 'H' section size 34.00x43.5x2mm thick with 4mm tinted sheet galss (Weight not less than 0.57 kg/RM and shutter 'Z' of size 34.00x43.5x28.00mm having thickness 2.00mm (Wt not less than 0.50kg/RM) and all necessary jointing cleats , glazing, clips rubber packing, aluminium snap beading Tower bolt 100mm long 1 No and sliding hinges 180mm longs including aluminium grill with Mosquito proofing etc complete all as specified and directed.

S&F 25/32 mm dia decorative/drapery curtain rod with bub & Bracket & internal tunnels complete all as specified and directed.

M&L preparation of old treated surfaces of walls (plastered or unplastered surfaces) and applying one coat of white wash on old decorated surfaces complete all as specified and directed.

All as per item No. 121 above but on ceiling

M&L preparation of old treated surfaces of walls (plastered or unplastered surfaces) and applying one coat of cement base paint complete all as specified and directed.

M&L preparation of old treated surfaces of walls (plastered or unplastered surfaces) and applying one coat of oil emulsion distemper (white / tinted) complete all as specified and directed.

M&L for preparaion of treated surfaces and apply one coat of weather coat paint on exteranal surfaces of walls complete all as specified and directed.

M&L preparation of old painted wooden/wood based surfaces over 10cm width or girth and applying one coat (finishing coat ) of synthetic enamel paint complete all as specified and directed.

M&L preparation of old painted steel surfaces over 10 cm width of girth and applying one coat (finishing coat) of synthetic enamel paint complete all as specified and directed.

M&L for one coat of synthetic enamel paint to plastered or concrete surface incl preparartion of old surface as in small patches for bases for writing bldg numbers complete all as specified and directed.

M&L for removing of sludge from septic tanks including removal of sludge water manually or mechanically in all respect and removing the sludge to distance not exceeding 500 mtrs and burried in to the ground and making to a true surface and covering with loose soil and as directed by Engr in charge. (The rate included excavation and filling )

M&L for cutting and removing wild bushes/ vegetation, surface dressing around the septic tank/sock well/ manholes to a distance of 2 mtrs all around and depositing surplus spoil/ rubbish exc 100M but n.exc 500 M complete all as specified and directed.

Cleaning of sewage line (length from manhole to manholes) of any dia by roding and flushing after cleaning and removing mud/sludge etc to a distance exc. 250m but n.exc 500m and spreading in low laying areas and covering with loose soil complete all as specified and directed.

Cleaning of manholes and removing sludge from manholes of any size and depth and deposing the sludge and spreading in low laying areas and covering with loose soil and as directed by Engr in charge.

Cleaning the blockage of floor trap, nahani trap, gully trap and first manhole complete all as specified and directed.

Excavation in trenches n.exc 1.5M wide and n.exc 1.5 M deep for foundation and getting out in soft/loose soil complete all as specified and directed.

Demolition and breaking up drain pipe of any description up to 150mm dia in CM 1:4 including demolition of cement concrete bedding and hunching complete all as specified and directed.

Demolition and breaking up drain pipe of any description up to 200mm dia in CM 1:4 including demolition of cement concrete bedding and hunching complete all as specified and directed.

M&L for PCC 1:3:6 type C-2 using 40mm graded stone aggregate as in concrete bed to drain pipe including packing under, and hunching against the sides of pipes after they are laid and tested for 150mm dia pipe complete all as specified and directed.

M&L for PCC 1:3:6 type C-2 using 40mm graded stone aggregate as in concrete bed to drain pipe including packing under, and hunching against the sides of pipes after they are laid and tested for 200mm dia pipe complete all as specified and directed.

Cutting in to existing manholes for connecting new drains, making good to pipe & rendering cutting out existing benching for and forming branch channel in cement concrete1:2:4 type B-1 smooth finished and reforming benching as required for 150 mm bore drain pipe complete all as specified and directed.

Cutting in to existing manholes for connecting new drains, making good to pipe & rendering cutting out existing benching for and forming branch channel in cement concrete1:2:4 type B-1 smooth finished and reforming benching as required for 200 mm bore drain pipe complete all as specified and directed.

M&L for cement concrete 1:4:8 type D-2 using 40 mm graded stone aggregate as in foundation and mass soncrete complete all as specified and directed.

M&L for cement concrete 1:2:4, type B-1, using 20mm graded stone aggregate as benching , surface channel and similar articles finishing even and smooth using extra cement complete all as specified and directed.

M&L for PCC 1:2:4 type B-1 using 20mm graded stone aggregate as in copings, bed plate, including weathering, slightly rounded or chamfered angles and throating with necessary form work complete all as specified and directed.

Returning, filling in, including spreading levelling, watering and well ramming in layers not exceeding 25cm thick complete all as specified and directed.

Removing excavated material n.exc 50m and depositing where directed at a level n.exc 1.5m above the starting point complete all as specified and directed.

Demolition of brick work built in cement mortar complete all as specified and directed.

M&L Brick work with fly ash bricks straight or curved on plan exc 6m mean radius built in CM 1:6 Complete all as specified and directed.

M&L rendering 10 mm thick in cement and sand mortar 1:6 on other than fair faces of brick work or cement concrete surfaces including finishing the surface even and smooth without using extra cement complete all as specified and directed.

Demolition of RCC of any description and in any position not other wise specially provided for reinforcement cut as required to facilitate demolition complete all as specified and directed.

M&L for pre cast cement concrete 1:2:4, type B-1, using 20mm graded stone aggregate as in cover slabs (for manholes etc) and similar articles with plain faces, set in CM 1:4 complete all as specified and directed.

M&L for mild steel 6 - 8mm dia TMT bars bent to shape required, including cranking, bending and binding with mild steel annealed wire not less than 0.9mm dia complete all as specified and directed.

Cleaning and removing all scale and dirt, etc, from tanks exc 250 ltr n.exc 500 ltr capacity and from mouths of circulating pipes, etc. including Disconnecting existing tanks, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position complete all as specified and directed.

Cleaning and removing all scale and dirt, etc, from tanks exc 500 ltr but n.exc 1000 ltr capacity and from mouths of circulating pipes, etc. including Disconnecting existing tanks, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position complete all as specified and directed.

Cleaning of 20000 glns capacity overhead water tanks by dewatering existing water and removing all dirt, silt, vegetation / fungus, formation on side walls and bottom by cleaning with wire brushes to remove all setteled mtrls and cleaning with water and applying lime washing two coats inside incl writing the date and due date complete all as specified and directed by Engr-In-Charge.

All as per Item No 157 above but underground sump of capacity 2000 ltrs

All as per Item No 157 above but underground sump of capacity 20000 Glns

M& L for Sand filling under floors or in foundations etc incl watering and consolidation, complete all as specified and directed.

M&L for machine pressed precast concrete inter locking paver block of any shape and size confirming to IS 15658-2006 of thickness 60mm, M-25 grade set and jointed with neat grey cement and pigment etc.complete all as specified and directed.

M&L for 20mm thick screed bed in cement mortar(1:6) as in bedding of chequered tiles complete all as specified and directed.

M&L for chequered cement concrete tiles 20cmx20cmx25mm thick set, jointed and painted with grey cement and pigment in neat cement slurry in floors complete all as specified and directed.

Supply and replacement of starting relay assembly suitable for refrigerator 165-200 ltrs capacity as per sample complete all as specified and directed.

Supply and replacement thermostat switch for refrigerator 165-200 ltrs capacity all as per sample complete all as specified and directed.

Supply and replacement cabin bulb 5 watt 230 Volts screw/pin type for refrigerators all as per sample complete all as specified and directed.

Supply and replacement door gasket magnetic type suitable for refrigerator 165-200 ltrs capacityall as per sample complete all as specified and directed.

Supply and replacement condenser coil suitable for refrigerator 165-200 ltrs capacity all as per sample complete all as specified and directed.

Supply and replacement of compressor for 165-200 litre capacity refrigerator including taking out old unsv and fixing on position with nuts, bolts, rubber gromote and washers, connecting copper tubing by welding/flare nuts, complete all as specified and directed.

Carrying out pressure leak test by nitrogen pressure for detecting leakage in condensing unit refrigerant pipe and repairing the leak by welding or brazing of condensing unit and refrigerant pipe, putting under pressure for leak checking after repairing of leak pipe including transporting & carrying out T&P required at site complete all as specified and directed. for refrigerators 165-200 ltrs.

Flushing out by N2 and CTC, vaccumnation and supply and charging of refrigerant gas into the system of refrigerant for refrigerators 165-200 ltrs.

S & F (in replacement) cooling coil for refrigerators 165-200 litre capacity after disconnecting the cooling coil from refrigerator, testing and flushing out the system and charging with refrigerant gas as per required quantity and testing complete all as specified and directed.

S&F in replacement candle like Carbon, membrance, sediment, alkaline, UV lamp and UV barrel for water fiiter any make/size as per sample all as per sample complete all as specified and directed.

S&F in replacement SV Valve for water fiiter any make/size as per sample all as per sample complete all as specified and directed.

S&F in replacement relay for water fiiter any make/size as per sample all as per sample complete all as specified and directed.

S&F in replacement motor for water fiiter any make/size as per sample all as per sample complete all as specified and directed.

S&F in replacement adopter for water fiiter any make/size as per sample all as per sample complete all as specified and directed.

Dismantling of water cooler of 40-80 ltrs storage capacity from its position, taking out water from its water tank cleaning of water tank by washing powder and with fresh water externally and internally and storage tank without disturbing the existing position and connecting the water line including GI fitting when required and PVC pipe connection complete all as specified and directed.

Taking out defective gasket of storage water cooler top cover and supply & fixing new rubber gasket of existing size complete all as specified and directed.

S & F (in replacement) condensing coil suitable for 40-80 ltrs capacity water cooler complete all as specified and directed.

S&F (in replacement) starting relay assembly including cover and clips suitable for water cooler of any capacity complete all as specified and directed. Make : HITECH/TECUMSEH

Supply and replacement starting capacitor 60/80 Mfd including taking out old unsv complete all as specified and directed. Make : SARADA/KELTRON/ORICAP

S&F (in replacement) capacitor 4 Mfd suitable for blower motor of water cooler complete all as specified and directed. Make : SARADA/KELTRON/ORICAP

S&F (in replacement) thermostat suitable for water cooler any capacity complete all as specified and directed. (Make : ROCKWELL/INDFOSS)

S&F (in replacement) push/lift type self closing taps suitable for water cooler complete all as specified and directed.

S&F (in replacement) PVC float valve assembly with ball suitable for 15 mm bore pipe of water cooler complete all as specified and directed.

Supply and replacement of compressor including disconnecting suction/ discharge copper tubing of water cooler including taking out old unsv and fixing on position with nuts, bolts, rubber gromote and washers, connecting copper tubing by welding/flame nuts, detecting leak and repairs if any, complete all as specified and directed.

Carrying out pressure leak test by nitrogen pressure for detecting leak in condensing unit, refrigerant pipe and repairing the leakage by welding or brazing of condensing unit refrigerant pipe, putting under pressure for leak checking after repairs of leak pipe including transporting & carrying out T&P required at site for work of water cooler complete all as specified and directed.

Flushing out by Nitrogen and CTC, vacuum and supply charging of refrigerant gas as existing into the system for water cooler complete all as specified and directed.

Dismantling of unserviceable legs of water cooler and supply & fixing new legs of water cooler made out of 16 gauge MS sheet including welding/riveting and reinstalling the same after repairs / replacement complete all as specified and directed.

Removing defective condensing fan motor of water cooler single phase 230 V 50 HZ and opening and replacing of Blower motor and cutting out the burnt wiring and cleaning the slots of rotor and rewinding of the same with the existing size of super enamelled copper winding wire including insulation, varnishing, greasing, replacement of bushes, reassembling including testing and commissioning complete all as specified and directed.

S&F water pump for desert cooler any make and size as per sample all complete all as specified and directed.

S&F cooling pad (benature/PVC ), (set of 3) for desert cooler any make and size as per sample complete all as specified and directed.

S&F capacitor 3.5 mfd complete all as specified and directed.

S&F float valve for desert cooler any make and size as per sample complete all as specified and directed.

Maint and servicing of window type/split type air conditioner including cleaning filter, washing with soap solution after removing from site and refixing complete all as specified and directed.

Supply and replacement of unserviceable compressor (sealed unit) from window type air conditioner of capacity 1.5 Ton on position with nuts, bolts, rubber gromote and washers, flare nuts including taking out old unsv compressor of approved make complete all as specified and directed.

Supply and replacement unserviceable compressor (sealed unit) from split type air conditioner of capacity 1.5 Ton on position with nuts, bolts, ruber gromote and washers, connecting copper tubing by welding/flare nuts including taking out old unsv compressor of approved make complete all as specified and directed.

Supply and replacement running capacitor 36/45/80 MFD suitable for 1.5 Ton window type and split type air conditioner including taking down old unsv complete all as specified and directed. Make : SARADA/KEIL/KELTRON/ORICAP

Supply and replacement starting relay assembly including coat & cover and clips suitable for window/split typeair conditioner all as specified and directed. Make : TECHNOMECH/KELTRON

Supply and replacement thermostat switch suitable for air conditioner 1.5 Ton capacity complete all as specified and directed.

Supply and replacement of blower motor suitable for 1.5 Ton window/split type air conditioner AC single phase 230 Volts including bushes, testing and commissioning complete all as specified and directed.

Supply and replacement of air filter Pad suitable for air conditioner 1.5 Ton capacity complete all as specified and directed.

Carrying out pressure leak test by nitrogen pressure for detecting leak in condensing unit, refrigerant pipe and repairing the leakage by welding or brazing of condensing unit and refrigerant pipe, putting under pressure for leak, checking after repairs of leak pipe including transporting and carrying out T&P required at site for work of 1.5 Ton capacity air conditioner complete all as specified and directed.

Flushing out by N2 and CTC, vaccumnation, supply and charging of refrigerant gas into the system for 1.5 Ton capacity air conditioner complete all as specified and directed.

Dismantling of defective cooling indoor/outdoor unit of 1.5 Ton capacity of split type air conditioner complete with connected piping and corded remote control etc and refixing on wall/floor after carrying out repairs and servicing and making good the disturbed surfaces complete all as specified and directed.

Supply and replacement of condensing unit of 1.5 Ton capacity complete with connected lead and iron stand etc including taking down old defective complete all as specified and directed.

Supply and replacement of cooling coil assembly suitable for air conditioner 1.5 Ton capacity complete all as specified and directed.

Supply and replacement suction copper pipe line heavy ½” dia with foam insulation and flair nuts from indoor to outdoor unit of split type air conditioner 1.5 Ton capacity complete all as specified and directed.

Supply and replacement suction copper pipe line heavy 3/8” dia with foam insulation and flair nuts from indoor to outdoor unit of split type air conditioner 1.5 Ton capacity complete all as specified and directed.

S&F single pole and neutral enclosure with a two pin and earth plug socket 240 volt with one MCB SP ‘C’ series rating 20 to 32 Amp incl taking down the old USNV complete all as specified and directed. Make: C&S/Polycab/Havells.

Supply and replacement heating unit (element) ISI marked of 1500 watts triangular/circuler shape as per sample required in existing geysers installed at site including rubber washers complete all as specified and directed. Make : Umpire/Wondercool/Ditz/ Toshiba

Supply and replacement vertical stainless steel inner container of capacity 25 litre with pressure relating 60 N/sqcm class -I made out of material and thickness of shell as per IS 2082/93 complete all as specified and directed.

Supply and replacement thermostat range 0°-75°C for the geysers of 25 to 35 litres as per sample required in existing geysers installed at site complete all as specified and directed.

Supply and replacement safety valve/high pressure valve 15 mm complete all as specified and directed.

Supply and replacement PVC threaded tough rubber flexible pipe/tubing of 15 mm size with PTMT nuts at both end 300/450 mm long for geysers inlet/ outlet connections, complete all as specified and directed.

Supply and replacement non return valve 15mm dia cast copper alloy ISI mark complete all as specified and directed.

Supply and replacement Indicator lamp rectangular/round type as required at site complete all as specified and directed.

Supply and replacement thermosyphon assembly suitable for geysers complete with inlet, outlet pipes with drain plug and screw for fixing the element inclusive of clamps for holding the element with nut, bolt and washers for 25 Litres to 35 litres capacity as per existing complete all as specified and directed.

Maintenance of existing earthing by cleaning the earth chamber, funnel, in and around the chamber by removing the vegetation complete and adding adequate water with 20 Kg salt and 20 kg coal complete all as specified and directed.

Dismantling of existing broken PCC earth chambers and providing earth chamber with PCC 1:3:6 type C1 (using 20mm graded stone aggregate) complete all as specified and directed.

Replacement of broken earth chamber cover by RCC cover 1:2:4 type B1, of size 550mm x 550mm x 40mm thick with handle of 10mm dia Bar at 6mm dia MS Bar @ 100mm c/c both ways complete all as specified and directed.

Supply and fix GI funnel on existing 20 mm dia pipe including dismantling of the unserviceable funnel complete all as specified and directed.

Supply and fix GI tubing light grade 40 mm bore fixed on walls, floors,in ground etc for GI wire protection including dismantling of the unserviceable complete all as specified and directed.

Making nitch in the existing PCC floor for inserting Pipe/strip etc and making good the same by matching with the existing complete all as specified and directed.

M&L PCC 1:2:4 type B1 using 20mm graded stone aggregate as in platform, filling and mass concrete, coping to pole etc incl dismantling/breaking the exisitng for all as specified, including necessary form work if reqd and applying two coats of white wash to exposed surface of copying/platform complete all as specified and directed.

S&F Test point block made of gun metal or phosphorus bronze size 75 x 75 x 25mm drilled and screwed incl 3 nos of 8 mm dia 25mm long hex.head screws complete all as specified and directd.

Comprehensive maintenance of DG Set including Alternator AMF Panel for routine check up of the engine for the smooth functioning and carrying out the checks complete as per the manufactures instructions complete all as specified and directed. for 15 KVA DG Sets installed. (A) Every 50 Hours/One month whichever is earlier (a) Repeat the daily checks (b) Check oil level in the oil bath type air cleaner (c) Check the fan belt tension. The deflection should be within 8 to 10 mm at the Centre (for details pleaser refer to the maintenance manual) (d) Check the electrical connection

Comprehensive maintenance of DG Set including Alternator AMF Panel for routine check up of the engine for the smooth functioning and carrying out the checks complete as per the manufactures instructions complete all as specified and directed. for 15 KVA DG Sets installed. (a) Every 200 hours/Six month whichever is earlier (b) Repeat the 'A' Checks (c) Service the oil bath type air cleaner (d) Replace the engine main lub oil filter element & sealing ring (e) Grease the water pump bearing (f) Clean the button filter (g) Replace the Air filte (h) Replace the filter element (Oil filter, fuel filter etc) complete. (j) Replace the lubricant oil (IC engine for Gen set application). Old oil should be drained out after warming the engine. (Use MIL-L 2104C mono-grade oils only/15W40 overlain cummins/equivalent) (k) Replace the engine and turbocharger lubricant oil filter element (l) Check oil level in the fuel pump and top up if required (m) Drain radiator after warming the engine, change the water (n) Knock out soot from the exhaust silencer (o) Check and tighten all fasteners to the specified torque (p) Check the tighten all hose connection check and tighten all lubricant and fuel connection.

Servicing of radiator assembly complete for cleaning after draining out cooling water/coolant, spaces cleaning the inter coller and replace unserviceable rubber hose pipes, circlip clamps, cleaning of raditor mix with appropriate cleaning agent, de-scaling by means of scale solvent as well as neutralising agent to arrest leakages by means of brazing etc including replacement of coolant for the capacity of DG Set 15 KVA complete all as specified and directed.

Supply and replacement of lead acid battery 75 Amp, 12 Volt, complete all as specified and directed. Make : EXIDE/AMCO

Repair and servicing of 15 KVA Engine Kirlosker type RB 66/Cummins turbocharger assembly and replacing the service kit and reassembling testing complete all as specified and directed.

Servicing of self starter assembly of DG Set 24/12 Volts of 15 KVA capacity by disconnecting the self starter assembly from the engine and dismantling cleaning all accessories, replacing worn out parts like carbon brushes contact plates jumping levels etc and rewinding the fields coil and warnishing complete all as specified and directed.

Supply and replacement of aluminium strip 25 x 3.15 mm with saddles and fixing screws etc for roof conductor above ground complete all as specified and directed.

Supply and replacement of Air termination single pointed aluminium rod 12mm dia and 300 mm long complete all as specified and directed. Note : The rate is inclusive of supporting pipe 15mm bore and PCC required at site.

Supply and replacement of galvanised iron strip 32x6 mm and fixing screws buried in ground or above ground for test point complete all as specified and directed.

Overhauling the fuel injection pump & injector for 15 KVA DG Set and dismantling and taking out to workshops for repair including the transportation by replacing the worn out/unserviceable parts like service kit D valve, elements & Nozzels guides etc as required & caliberation the same commissioning etc complete all as specified and directed.

Opening the coupling and dismantling the alternator carefully by removing the flywheel and dismantling the unservicable starting gear wheel, supply and fixing new starting gear for 15 KVA DG set, complete all as specified and directed.

Supply and replacement of Automatic voltage regulator (AVR) suitable for DG Set 15 KVA,complete all as specified and directed.

Supply, jointing, fixing or passing through pipe, trenches or ducts,commissioning and testing XLPE insulated screened and PVC sheathed armoured electric power LT cable heavy duty with aluminium conductor nominal cross sectional area 70 Sqmm 3.5 core for working voltage upto including 1100 volts confirming to IS - 7098 (Part-I) 1988, including taking down existing cable, complete all as specified and directed.

Earthing complete with galvanised steel earth plate electrode 60cmx60cmx6mm thick buried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of plate not less than 1.5 mtr below ground level, connecting to galvanised iron strip 32mm X 6mm (as earth lead strip), by means of bolt, nuts, check nuts and washer of GI and GI strip protected by provision of GI pipe light grade, 40mm bore upto test point including provn of concrete pit in PCC (1:2:4) type B-1 using 20mm graded crushed stone aggregates with 40mm thick cover of RCC (1:2:4) reinforced with XPM (weight not less than 4 kg/Sqm) and frame of angle iron 25 x 25 x 3 mm with lugs 2 Nos and with 6mm dia MS bar handle made to shape, GI medium grade 20mm bore pipe for watering perforated at bottom 1.75 metres long placed on top edge of earth plate, common salt and charcoal filling, test point made out of phosphorous bronze with fixing arrangement, funnel, wire mesh and earth work in hard/dense soil, returning filling in and removal of surplus soil to a distance not exceeding 50 mtr, all as per electrical plate No 3 of SSR 2009 Part-I and connection to earth test point all as specified and testing on completion. NOTE :- Item of earthing includes the cost of 7.5 metre long galvanised iron strip 32mm X 6mm size and protection pipe of 40 mm bore galvanised iron light grade.

Taking down carefully copper/aluminum point wiring (light, fan/exhaust fan, bell, socket or power) complete with fittings and fixtures such as switches, ceiling roses, pendants, regulators, socket, lamp holders, brackets, bell, bulk head fittings etc removing material to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and also making good disturbed surfaces of wall, floors etc complete all as specified and directed.

M&L for point wiring with 1.5 Sqmm copper conductor (Multi-stranded) PVC insulated and unsheating FRLS electric cable 1100 volts cable and including PVC casing and caping of suitable size (as per conductor run) with all fittings/ accessories and including PVC insulated electric cable 1100 volts 1.5 Sqmm ( multi-stranded) copper conductor single core( Green colour) cable as continuous earth wire connected to common earth dolly by providing lugs including sunk in pressed steel terminal boxes of 1.6 mm thick concealed in wall (duly painted with two coats of black bituminous paint over a coat of red oxide primer in and out sides) with and including cutting holes for switches, sockets, regulators etc as per requirement including fixing with machine screw, washer etc and making good disturbed surfaces of wall and matching colour as per existing complete all as specified and directed. Make of wire : Plaza/Polycab/Havells. (a) One light point controlled by one, one way switch

(b) One fan/exhaust fan/bell point point controlled by one, one way switch

(c) One 5 Amp socket point controlled by one way switch on independent board.

(d) One 5 Amp Socket point controlled by one way switch on the same board with other switches.

All as per item No 241 above, but for one socket outlet 15 Amps on independent board with 2.5 Sqmm copper conductor ( Multi-stranded) PVC insulated and unsheating electric cable 1100 volts (ISI Marked) including PVC insulated and unsheathed electric cable 1100 volts 2.5 Sqmm copper stranded conductor as continuous earth wire connected to common earth dolly complete all as specified and directed Make of wire : Plaza/Polycab/Havells.

M&L for socket outlet 2 in 1, 3 pin, 5A flush type complete all as specified and directed. Make : Indo Asian/ Plaza/ Havells/Anchor

M&L for socket outlet 2 in 1, 3 pin, 5 Amp and 15 Amp flush type complete all as specified and directed. Make :Indo Asian/ Plaza/Havells/Anchor

M&L for Switch piano flush button 5 Amps complete all as specified and directed. Make : Indo Asian/Plaza/Havells/Anchor

M&L for Switch piano flush type single pole one way 15 Amp complete all as specified and directed. Make : Indo Asian/Plaza/ Havells/Anchor

M&L for ceiling rose surface type, 65 mm x 50 mm two to three terminals/PVC/polycarbonate, isolated body fixed on PVC block complete all specified and directed Make : Indo Asian/Plaza/Havells/Anchor

S&F Ceiling Fan regulator electronic step type as per sample complete all as specified and directed. Make : Indo Asian/Plaza/Havells/Anchor

M&l for wooden rectangular block of size suitable for DB 8 way/DB 4 way TPN, closed recessed 3mm thick plastic laminated sheet complete all as specified and directed.

S&F PVC insulated copper wire 1.5 Sqmm, single core including taking out old unsv wire complete all as specified and directed. Make : Havells or equivalent in Polycab/Plaza.

S&F PVC insulated copper wire 2.5 Sqmm, single core including taking out old unsv wire complete all as specified and directed. Make : Havells or equivalent in Polycab/Plaza.

S & F LED light fitting 1 x 20 Watt T5 batten type, indoor decorative PC housing extruded T5 LED integrated batten complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size incl taking down the old USNV complete all as specified and directed Make: C&S Cat No LTTB4F20WLEDEW batten or equivalent in Surya/Havells.

S&F LED light fitting 1 x 20 Watt LED MS batten complete with retrofit T8 polycarbonate tube complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size incl taking down the old USNV complete all as specified and directed . Make C&S Cat No LTDC1220WLED/WD (LTDC161820WLED+LT4F20WLEDT8/WDI) or equivalent in Surya/Havells.

S & F LED light fitting 1 x 10 Watt T5 batten type, indoor decorative PC housing extruded T5 LED battens integrated type complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size incl taking down the old USNV complete all as specified and directed Make C&S Cat No LTTB2F10WLEDEW batten or equivalent in Surya/Havells.

S&F LED lamp 9 Watt complete all as specified and directed. Make : C&S Cat No LTHPLEDLAMP9W/B22 or equivalent in Polycab/Havells.

S&F LED Bulk Head fitting in engineering plastic housing with clear prismatic diffuser complete all as specified and directed. Make : C&S Part No CG801B6WLED 6W LED Bulk Head or equivalent in Surya/Havells.

M&L for angular type lamp holder, PVC/ polycarbonate type with back plate suitable for 15/18 watts for batten fitting, including plastic square board of required size complete all as specified and directed. Make : Indo Asian/Plaza/Havells/Anchor.

S&F ceiling LED down light 12 watt round/square complete including taking down old unsv complete all as specified and directed. Make : C&S Cat No LTCRSLM12HPLEDSQ/W or equivalent in Surya/Havells.

Supply and fix recess/ceiling down lights 36 watt LED (600x600mm) size, ultra slim with extruded alumininium housing and milky diffuser complete including taking down old unsv complete all as specified and directed. Make : C&S Cat No LTCRSLM36WATT2x2 or equivalent in Surya/Havells.

Taking down and re-fixing, connecting existing electric meters, single/three phase complete all as specified and directed.

S&F switch socket combination multipurpose 2 in 1 3 pin, 5 Amp flush type complete all as specified and directed. Make : Havells/Plaza/SSK/Polycab

S&F switch socket combination 2-in-1, 3/5 pin 5 and 15 Amp incl taking down the old USNV complete all as specified and directed. Make : Havells/Plaza/SSK/Polycab

S&F modular switch single pole 1 way 6A, complete all as specified and directed. Make : Crabtree/CONA/Havells.

S&F modular socket outlet 6A 2/3 pin combined 2 module complete all as specified and directed. Make : Crabtree/CONA/Havells

S&F modular switch 16A single pole one way complete all as specified and directed. Make : Crabtree/Cona/Havells.

S&F socket outlet 6A/16A- 2/3 pin combined 2 module complete all as specified and directed. Make : Crabtree/Cona/Havells.

M&L for modular Bell push Switch single pole one way 6A/10Amps complete all as specified and directed. Make : Crabtree/Cona/Havells.

M&L for call bell modular type AC 230 volt single pole complete all as specified and directed. Make : Crabtree/Cona/Havells.

M&L for fan step regulator, 120, W-2 module complete all as specified and directed. Make : Crabtree/Cona/Havells.

S & F bell push piano (Flush type) 5 Amp 240 Volts incl taking down the old unsv complete all as specified and directed.Make : Anchor/Cona/Havells.

S & F bell/buzzer electric single phase 240 volt incl taking down the old unsv complete all as specified and directed. Make : Anchor/Cona/Havells.

S&F single pole and neutral enclosure with a two pin and earth plug socket 240 V with one MCB SP ‘C’ series rating 20 to 32 Amp incl taking down the old unsv complete all as specified and directed. Make : Polycab /C&S/Havells.

S&F PVC conduit pipe 20 mm dia complete alongwith necessary fixing arrangement incl taking down the old USNV complete all as specified and directed.

S&F PVC casing capping 25mm complete alongwith necessary fixing arrangement incl taking down the old USNV complete all as specified and directed.

S&F MCB TPN 100 Amp, 415 Volts incl taking down the old USNV complete all as specified and directed. Make : C&S/Polycab/Havells

S & F MCB TPN 63 Amp 415 Volts incl taking down the old USNV complete all as specified and directed. Make : Polycab/Havells/ C&S.

S & F MCB TPN 40 Amp 415 Volts incl taking down the old USNV complete all as specified and directed. Make : Polycab/ Havells/C&S.

S&F Isolator DP 32A, 240 volts complete all as specified and directed. Make : Polycab/C&S

S&F MCB SP 10 to 32 Amp, 240 volt complete all as specified and directed. Make : C&S/Polycab/Havells.

S&F Sheet metal enclosure for DB’s suitable for MCBs of triple pole and neutral 4 way double door type with 200 amp rated bus bar complete all as specified and directed. Make : C&S/Polycab/Havells.

S&F Sheet metal enclosure for DB’s suitable for MCBs of single pole and neutral 8 way (Double door) with 200 amp rated bus bar complete all as specified and directed. . Make : C&S/Polycab/Havells.

S&F for sub main wiring two single core PVC insulated and unsheathed cable with 10 Sqmm multi-strand copper conductor including in PVC casing caping/conduit with 10 Sqmm PVC copper conductor cable as in earth wire system ,including taking out old wiring complete all as specified and directed. Note : Three runs of wire for phase, neutral and earth will be measured as single run. Make : Havells or equivalent in Polycab/Plaza

Supply and fixing for sub main wiring two single core PVC insulated and unsheathed cable with 6 Sqmm multi-strand copper conductor including in PVC casing caping with 6 Sqmm PVC copper conductor cable as in earth wire system ,including taking out old wiring complete all as directed. Note : Three runs of wire for phase, neutral and earth will be measured as single run. Make : Havells or equivalent in Polycab/Plaza.

S&F for sub main wiring two single core PVC insulated and unsheathed cable with 4 Sqmm multi-strand copper conductor including in PVC casing caping with 4 Sqmm PVC copper conductor cable as in earth wire system ,including taking out old wiring complete all as specified and directed. Note : Three runs of wire for phase, neutral and earth will be measured as single run. Make : Havells or equivalent in Polycab/Plaza.

M&L for complete removal of existing painting by scrapping the old surface, preparation of fan surface and applying spray painting with spray nozzle to ceilling fan of any make and any size with two coat of synthetic enamel paint as existing colour/shade over a coat of red oxide primer complete all as specified and directed.

M&L for taking down ceiling fan & Exhaust fan of any make and any size for repair/replacement of defective spare parts and overhauling the fans by cleaning, greasing and replacement of old split pin, rubber reel, connected items and provide flexible wire of size 23/0.0076 for connection from ceiling rose to fan/exhaust fan, refixing the same and testing complete all as specified and directed. Note:- Rewinding, painting and supply of new components will be measured and paid separately under relevant items complete all as specified and directed.

M&L for rewinding the ceiling fan any make 1200/1400mm sweep and any size with super quality copper conductor adequate winding wire of existing size complete all as specified and directed.

M&L for rewinding the exhaust fan any make 300/450mm sweep any size with super quality copper conductor adequate size of winding wire of existing size, refixing the ball bearing, greasing complete all as specified and directed .

Supply only ball bearing of suitable size for ceilling fans complete all as specified and directed. Make : SKF /TATA /NBC

Supply only capacitor of 4 MFD, 240 Volt suitable for ceilling/exhaust fan complete all as specified and directed. Make :- Universal /Usha/ Electro

Supply only capacitor of 2.5 MFD, 240 Volt suitable for ceilling/ exhaust fan complete all as specified and directed. Make : Universal/ Usha/Electro

Supply only down rod of ceiling fan with medium grade of 15 mm size pipe complete with drilling holes, cutting and making threads as per site requirement up to 0.50 to 1 mtr, painting with two coats of paint as existing complete all as specified and directed.

S&F PVC flexible pipe of size 15mm or 20 mm all as per site reqmt for protectin of wire complete all as specified and directed.

S&F Plastic enclosure without MCB SP & DP as required in site with fixing on wall/pole etc with binding/fixing material complete all as specified and directed. Make : C&S/Havells/Indo Asian.

S&F PVC insulated copper wire 1 Sqmm, three core including taking out old unsv wire complete all as specified and directed. Make : Havells or equivalent in Polycab/Plaza.

S&F PVC insulated copper wire 1.5 Sqmm, three core including taking out old unsv wire complete all as specified and directed. Make : Havells or equivalent in Polycab/Plaza.

S&F modular cover plate with frame 1 module as per sample complete all as specified and directed.

S&F modular cover plate with frame 2 module as per sample complete all as specified and directed.

S&F modular cover plate with frame 3 module as per sample complete all as specified and directed.

S&F modular cover plate with frame 4 module as per sample complete all as specified and directed.

S&F modular cover plate with frame 6 module as per sample complete all as specified and directed.

S&F modular cover plate with frame 8 module as per sample complete all as specified and directed.

Earthing complete with galvanised steel earth plate electrode 60cm x 60cm x 6 mm thick buried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) with top edge of plate not less than 1.5 Metres below normal ground level, connecting to the Galvanised iron earth lead wire 4mm dia, by means of bolts, nuts, check nuts and washers of galvanised iron and 4mm earth lead protected by provision of GI medium grade pipe 15mm bore including provision of concrete pit in PCC (1:2:4) type B-1 using 20mm graded stone aggregates with 40mm thick cover of RCC (1:2:4) reinforced with XPM (weight not less than 4Kg/Sqm) and frame of angle iron 25x25x6mm with lugs 02 Nos and with 6mm dia MS bar handle made to shape, GI medium grade 20mm bore pipe for watering perforated at bottom 1.75 metre long placed on top edge of earth plate, common salt and charcoal filling, test point made out of 75x50x6mm phosphorous bronze with fixing arrangement, funnel, wire mesh and earth work in hard/dense soil, returning filling in and removal of surplus soil to a distance not exceeding 50 metres, all as per electrical plate No 3 of SSR-2009 Part-I and connecting to earth test point including testing on completion complete all as specified and directed.

supply and replacement bolts, nuts and washers, rubber reel, capacitor clamp, split pin of appropriate size as required at site for ceiling fan of any size complete all as specified and directed.

M&L for replacement of unserviceable spindle and check nuts of stainless steel, valve and gland packing materials from the existing sluice valve and re-assembling properly complete all as specified and directed. for150 mm bore

All as per item No 308 above but 100 mm bore complete all as specified and directed.

S&F foot valve 50/63 mm dia CI/GI with complete fittings including taking out old unsv as per sample approved complete all as specified and directed.

S&F of 3 layer PP-R (polypopropylene random co-polymer) pipes SDR 7.4/PN16 UV steblised and antimicrobial fusion welded having thermal estability for hot and cold water supply all PP-R plain end brass threaded polypopropylene randum fittings laid in trenches 110 mm O/D complete with all connected fittings incl taking down old unsv complete all as specified and directed. (ISI marked) Make : KPT/SFMC/SUPREME.

All as per item No 311 above but 90 mm O/D complete all as specified and directed.

All as per item No 311 above but 63 mm O/D complete all as specified and directed.

All as per item No 311 above but 50 mm O/D complete all as specified and directed.

All as per item No 311 above but 40 mm O/D complete all as specified and directed.

All as per item No 311 above but 32 mm O/D complete all as specified and directed.

All as per item No 311 above but 25 mm O/D complete all as specified and directed.

S&F in replacement of PP-R gate valve 110 mm O/D (brass insert) complete all as specified and directed. Make : SFMC/SUPREME/KPT (ISI mark).

S&F in replacement of PP-R gate valve 90 mm O/D (brass insert) complete all as specified and directed. Make : SFMC/SUPREME/KPT (ISI mark)

S&F in replacement of PP-R gate valve 63 mm (brass insert) O/D complete all as specified and directed. Make : SFMC/SUPREME/KPT (ISI mark)

All as per item No 320 above but for size 50 mm O/D complete all as specified and directed. Make : SFMC/SUPREME/KPT (ISI mark)

All as per item No 320 above for size 40 mm O/D complete all as specified and directed. Make : SFMC/SUPREME/KPT (ISI mark)

All as per item No 320 above for size 32 mm O/D complete all as specified and directed. Make : SFMC/SUPREME/KPT (ISI mark)

All as per item No 320 above for size 25 mm O/D complete all as specified and directed. Make : SFMC/SUPREME/KPT (ISI mark)

S&F in replacement Gun metal gate valves 80 mm (ISI marked) complete all as specified and directed.

S&F cast iron sluice valve 100 mm with stainless spindles with flanged ends ISI marked PN1 type complete incl taking out old unsv complete all as specified and directed.

S&F cast iron sluice valve 80 mm with stainless spindles with flanged ends ISI marked PN1 type complete incl taking out old unsv complete all as specified and directed.

S&F in replacement NRV 80 mm with stainless spindles with flanged ends ISI marked PN1 type complete all as per existing make and type complete all as specified and directed.

S&F foot valve 80 mm dia with complete fittings incl taking out old unsv complete all as specified and directed.

Taking down unsv pump set 10 HP capacity, 3 phase KSD type-1030 with impillar from connected pipe line, dismantling existing motor/pump, rewinding motor by supper enamelled copper wire with existing size, insulation and varnishing complete, replace wornout ball bearing and gland packing of existing pump set and refitting the repaired pump set on pipe line, testing and commissioning complete all as specified and directed.

Taking down unsv submersible pump set 7.5 KW/HP capacity, 7 stage, 3 phase KSB from bore well, repair/rewinding motor by super enamelled copper wire with existing size, insulation and varnishing complete, replace wornout ball bearing and items as required and refitting complete in all respect, testing and commissioning complete all as specified and directed.

Taking down unsv booster pump 05 HP capacity, 3 phase from UG sump from existing connected pipe line, dismantling existing motor/pump, rewinding motor by supper enamelled copper wire with existing size, insulation and varnishing complete, replace wornout ball bearing and refitting the repaired booster pump on pipe line, testing and commissioning complete all as specified and directed.

Supply and fix Heavy duty DOL starter12 HP, 9 KW, type DX-P with robust 4 pole contactor & LR1D OLR in S.S enclosure including taking down old unsv all as specified and directed. Make : C&S Cat No BE1-DXP204 321 or equivalent in Polycab/HPL/L&T.

Supply and fix Heavy duty automatic Star Delta Starter 12 HP, 9 KW Type DX-P with robust 4 pole contactor & LR1D OLR, electronic Star Delta timer in S.S enclosure all as specified and directed. Make : C&S Cat No BE3-DXP204 314 or equivalent in Polycab/HPL/L&T.

Supply and replacement of media of water pressure filter capacity 3-6 cum including taking out old unsv, servicing of iron removal plant and painting with spray maching with two coat of synthetic enamel paint complete all as specified and directed.

Cutting of road, pavement, hard standing by skilled labour known better to work with neatly for laying of GI/DI/PPR pipes suitable for working pressure and making good of disturbed surface of cutting road/hard standing/pavement by existing material or PCC as it look before cutting complete all as specified and directed.

M&L for construction of brick masonary valve pit chamber internal dia (1200x1200x1200mm) including necessary excavation and earth work in any type in CM (1:4) complete with valve pit cover GI Sheet cover 4 mm thickness and locking arrangement with lock and key including painting complete all as specified and directed

M&L for construction of brick masonary valve pit chamber internal dia (900x900x900 mm) including necessary excavation and earth work in any type in CM (1:4) complete with valve pit cover GI Sheet cover 4 mm thickness and locking arrangement with lock and key including painting complete all as specified and directed

V.Venkata Ramaiah

M/s Bapujee Builders and Traders

RPL SYNDICATE CO

ALLIANCE

Bansal And Co