CRR

Clearing and grubbing road land including uprooting rank vegetation, grass, bushes, shrubs, saplings and trees girth up to 300 mm, removal of stumps of trees cut earlier and disposal of unserviceable materials and stacking of serviceable material to be used or auctioned, up to a lead of 1000 metres including removal and disposal of top organic soil not exceeding 150 mm in thickness by Mechanical means as per the Techinical Specification Clause 201 MoRTH 5th Revision

Forming Embankment with material obtained from borrowed useful earth from outside road boundary by mechanical means upto SDR with all leads and lifts including pre-watering of soil at borrow area, removal of top soil, excavation of soils at borrowed area, conveyance of soil, depositing the soil on the embankment, spreading soil, breaking clods, sectioning, grading and consolidation with 8 to 10 Tonnes Vibratory Road Roller @ OMC to meet requirement of table 300-2 of MoRT&H, including all hire and operational charges of T&P, complete for finished item of work as per MoRT&H specification 305 (5th revision). (The soil CBR>10%, PI<18% & MDD>1.8 g/cc) ( with a lead of 10 Km )

Construction of earthen shoulders with selective soils obtained from borrow pits with MDD of 18 KN/Cum , CBR ≥ 12%, PI < 12% from approved sources, grading and consoilidation with 8 to 10 Tonnes Vibratory Road Roller @ OMC to meet requirement of MoRT&H, including all hire and operational charges of T&P complete for finished item of work as per MoRT&H specification 305 (5th revision)

Construction of Granular sub-base by providing HBG material confirming to Grading - VI of MoRT&H (Table 400-1 & 400-2) including cost, and conveyance of all materials to work site and spreading in uniform layers with motor grader or by approved means, on prepared surface mixing by mix-in-place method with rotavator / approved means at OMC and compacting with vibratory roller to achieve CBR value minimum of 30% at 98% of dry density and PI value maximum 6, complete for finished item of work as per MoRT&H Specification 401 (5th revision) including contractors profit & Over head charges excluding Seignarage charges etc

Providing, laying, spreading and compacting graded stone aggregate to Wet mix macadam specification including premixing the material with water at OMC in mechanical mixer (Pug Mill), carriage of mixed material by tipper to site, laying in uniform layers in sub-base/base course on a well prepared sub-base and compacting with Vibratory roller of 80 to 100kN to achieve the desired density including lighting, barricading and maintenance of diversion, etc as directed by the Engineer-in-Charge and as per Technical Specification Clause 406 MoRT&H ( 5th revision ), including overhead charges & Contractor profit excluding Seignarage charges etc complete.

Providing and applying primer coat with bitumen emulsion (SS-1) on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.60 kg/sqm using mechanical means, as directed by the Engineer-in-Charge and as per Technical Specification Clause 502 MoRT&H (5th Revision) (for use on Wet mix macadam & WBM) ,including overhead charges & Contractors profit excluding Seignarage charges etc complete.

Providing and applying tack coat with Bitumen emulsion (RS-1) using emulsion distributor at the rate of 0.275 kg per sqm on the prepared granular surfaces treated with primer & cleaned with Hydraulic broom,as directed by the Engineer-in-Charge and as per Technical Specification Clause 503 MoRT&H (5th Revision), including overhead charges & Contractors profit excluding Seignarage charges etc complete.

Providing and laying bituminous concrete with 100-120 TPH batch type hot mix plant producing an average output of 75 tonnes per hour using crushed aggregates of grading-II premixed with bituminous binder 60/70 @ 5.4 to 5.6 percent of mix and filler with stone dust, transporting the hot mix to work site, laying with a Mechanical paver finisher to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MORTH specification clause No. 507 complete in all respects

Earthwork excavation in soils upto SDR by mechanical means for foundations of structures as per drawing and technical specification including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing sides of bottom, back filling the excavation earth to the extent required etc., complete excluding seignioarge charges for finished item of work as per MoRT&H specification 304(5th Revision) and as directed by the Engineer-in-Charge.

Sand Filling in foundation trenches as per drawing and technical specification Clause 304 of MORTH including overhead charges & Contractors profit etc complete.

Providing PCC M15 mix using 40mm, 20mm & 10mm size HBG crushed stone aggregate and fine aggregate(Natural sand 50%+Manufactured sand(Rock Sand)50% ) conforming to table 1000-2 of MoRT&H including cost, conveyance of all materials to site and labour charges, centering, machine mixing, laying, Vibrating, curing etc., including all other incidental and operational charges of all T&P etc., complete for finished item of work as per MoRT&H specification 1500,1700, 2100 (5th Revision) and as directed by the Engineer-in-Charge for foundation.

Providing PCC M15 mix using 40mm, 20mm & 10mm size HBG crushed stone aggregate and fine aggregate(Natural sand 50%+Manufactured sand(Rock Sand)50% ) conforming to table 1000-2 of MoRT&H including cost, conveyance of all materials to site and labour charges, centering, machine mixing, laying, Vibrating, curing etc., including all other incidental and operational charges of all T&P etc., complete for finished item of work as per MoRT&H specification 1500,1700, 2100 (5th Revision) and as directed by the Engineer-in-Charge for Substructure.

Providing Plain Cement Concrete (1:3:6) mix using 40mm size HBG crushed stone aggregate and fine aggregate(Natural sand 50%+Manufactured sand(Rock Sand)50% ) conforming to table 1000-2 of MoRT&H including cost, conveyance of all materials to site and labour charges, centring, machine mixing, laying, Vibrating, curing etc., including all other incidental and operational charges of all T&P etc., complete for finished item of work as per MoRT&H specification 1500,1700, 2100 (5th Revision) and as directed by the Engineer-in-Charge for Levelling Coarse

Providing, laying Reinforced cement concrete Hume pipes of 1000 mm Dia., NP4 class for pipe culverts including cost and conveyance of Pipes etc., complete and Labour charges for laying, jointing of 1000mm dia. R.C.C NP-4 Class Hume pipes in position including lifting, aligning, lowering and hoisting etc., as per drawing and as per MoRT&H Specification 2900, 2905 and 2906 (5th Revision) and IRC Special Publication No: 13 and as directed by the Engineer-in-Charge for finished item of work.

Earthwork excavation in soils upto SDR by mechanical means for foundations of structures as per drawing and technical specification including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing sides of bottom, back filling the excavation earth to the extent required etc., complete excluding seignioarge charges for finished item of work as per MoRT&H specification 304(5th Revision) and as directed by the Engineer-in-Charge.

Sand Filling in foundation trenches as per drawing and technical specification Clause 304 of MORTH including overhead charges & Contractors profit etc complete.

Providing PCC M15 mix using 40mm, 20mm & 10mm size HBG crushed stone aggregate and fine aggregate(Natural sand 50%+Manufactured sand(Rock Sand)50% ) conforming to table 1000-2 of MoRT&H including cost, conveyance of all materials to site and labour charges, centering, machine mixing, laying, Vibrating, curing etc., including all other incidental and operational charges of all T&P etc., complete for finished item of work as per MoRT&H specification 1500,1700, 2100 (5th Revision) and as directed by the Engineer-in-Charge for foundation.

Providing PCC M15 mix using 40mm, 20mm & 10mm size HBG crushed stone aggregate and fine aggregate(Natural sand 50%+Manufactured sand(Rock Sand)50% ) conforming to table 1000-2 of MoRT&H including cost, conveyance of all materials to site and labour charges, centering, machine mixing, laying, Vibrating, curing etc., including all other incidental and operational charges of all T&P etc., complete for finished item of work as per MoRT&H specification 1500,1700, 2100 (5th Revision) and as directed by the Engineer-in-Charge for Substructure.

Providing Plain Cement Concrete (1:3:6) mix using 40mm size HBG crushed stone aggregate and fine aggregate(Natural sand 50%+Manufactured sand(Rock Sand)50% ) conforming to table 1000-2 of MoRT&H including cost, conveyance of all materials to site and labour charges, centring, machine mixing, laying, Vibrating, curing etc., including all other incidental and operational charges of all T&P etc., complete for finished item of work as per MoRT&H specification 1500,1700, 2100 (5th Revision) and as directed by the Engineer-in-Charge for Levelling Coarse

Providing, laying Reinforced cement concrete Hume pipes of 1000 mm Dia., NP4 class for pipe culverts including cost and conveyance of Pipes etc., complete and Labour charges for laying, jointing of 1000mm dia. R.C.C NP-4 Class Hume pipes in position including lifting, aligning, lowering and hoisting etc., as per drawing and as per MoRT&H Specification 2900, 2905 and 2906 (5th Revision) and IRC Special Publication No: 13 and as directed by the Engineer-in-Charge for finished item of work.

Fabrication, Transportation and supply of hot-dip galvanized Octogonal Pole with BSEN-10025 grade S 355 JO steel plate for shaft, IS 2062 for base plate with door opening arrangement, including chain for anti theft mechanism, supply of suitable boards with bakelite sheet, din channel for MCB's as per IsS specification suitable to withtand the wind speed of 180 KMPH for "9 Mtrs height Pole having dimensions Bottom 15533, Top70mm with 3mm thick, base plate 260x260x16mm and 4 Nos of m24x750mm long J bolts along with template Makes. BAJAJ / VALONT/TRANSPRAIL MCB Makes: 6A,10KA, ISI marked,C/D curve of makes Legrrand DX/3 Schneider Acti 9

Fabrcation, Transportation and supply of 1.5 Mtr sword type or any decorative double arm bracket with dooms complete with all accessories with MS galvanized 50mm dia pipe

Foundation and Erection charges with special T&P for 9.00Mtrs/10Mtrs long Octagonal/Conical Pole dukly erecting on base plate duly providing 4 Nos foundation bolts with nuts with providing of 0.60Mtr x 0.60 Mtrs x 1.40 Mtr size M20 CC work vibrated concreting mixing with necessary steel (15Kgs) reinforcement as directed by the field engineers during execution including centering, water curing as required soil excavation, back filling , muffing removal and coil earthing including all labour charges and cost and conveyance of materials

Supply and Transporation of 120W LED Street Light Body made of high grade pressure die-cast Aluminium alloy with corroaion resistant powder coal , having protective toughened glass cover, less Glare , IP 66(Silicon gasket ensure Optical & Electrical compartments are IP 66) protected , wide operating voltage range, P.F> 0.90. System having more than 10KV inbuilt and more than 4KV external,THD<15% CCT:3000-6500K as desired by the department and as per IS, CRI>80, Inbuilt Electrical Protections like Over voltage, short circuit , over load , Open circuit, miswiring, etc complete with BIS manufacturer warranty letter, LM 79 andLM 80 certificates MAKE: PHILIPS/OSRAM/CROMPTON/BAJAJ/Wipro/HAVELLS/Jaquar/Eveready/Polycab LED MAKE: PHILIPS LUMILEDS/CREE/NICHIA/OSRAM/SAMSUNG/ LG LEDs

Fabrication,Transportaion and supply of 12 Mtrs Polygon High Mast with single section of 3mm thick Bottom 360mm and 150mm dia with BSEN-10025 grade S 355 JO steel plate for shaft, IS 2062 for base plate, having a base plate of size 520mm dia 16mm thick with its accessories.Mast shall be in single section for 12 Mtrs and 2 velocity of 180 KMPH as per IS 875 part 3 including head frame, 2 point suspension system with steel rope 6mm dia (7/19) constrcution double drum winch/power tool operating spped of 900RPM and necessary cable trailer connections and single speed motor with M 24 x 800mm foundation boltd of required quantity, suitable for 6 luminaires with GLS type aviation twin lamp Makes: BAJAJ/VALMONT/TRANSRAIL

Earth work excavation wot ha approximate Quantity of 4.0 Cum for errecyion of 12Mtrs hig hmast and refilling with a quantity of 0.52 cum of PCC 1:4:8, 1.50 Cum M20 grade concrete and (80Kgs) reinfoced steel of 12mm/10mm/8mm, soil bearing capacity of 10 T/Sqm, Anchor plate with cost and conveyance of all above materials including labour charges for errection of High Mast and Carriage etc complete including soil testing

Supply and Transporation of 150W LED Street Light Body made of high grade pressure die-cast Aluminium alloy with corroaion resistant powder coal , having protective toughened glass cover, less Glare , IP 66(Silicon gasket ensure Optical & Electrical compartments are IP 66) protected , wide operating voltage range, P.F> 0.90. System having more than 10KV inbuilt and more than 4KV external,THD<15% CCT:3000-6500K as desired by the department and as per IS, CRI>80, Inbuilt Electrical Protections like Over voltage, short circuit , over load , Open circuit, miswiring, etc complete with BIS manufacturer warranty letter, LM 79 andLM 80 certificates MAKE: PHILIPS/OSRAM/CROMPTON/BAJAJ/Wipro/HAVELLS/Jaquar/Eveready/Polycab LED MAKE: PHILIPS LUMILEDS/CREE/NICHIA/OSRAM/SAMSUNG/ LG LEDs

Supply and run of 1.5 Sqmm 3 core PVC insulated and FRLS Round Sheatherd Multi Core Bright Annealed Bare Copper Conductor Heavy Duty industrial Cables for voltage Grade up to 1100 volts as oer IS: 694:1990 including all transportaion chrges etc. completed. Makes: Finolex/RR Kabel/Havells/Polycab/RPG/KEI

Supply of ISI marked 16sqmm 4 core XLPE insulated 1100V grade armored alluminium cable as per specification confirming to IS: 7098 (Part -I) makes: Torrent/Uncab/Polycab/Havells)ELEC.4.1.1(f))

Supply of heavy duty long barrel alluminium legs conforming to I.S specifications suitable for 16sqmm cable etc. complete with nuts, bollts and washers. Makes: DMI/Jaison/Dowels(ELEC-4.4.2)

Supply of Heavy duty type single compression brass cable glands duly nickel plated complete with brass cheknut outer sheath sealing rubber ring and washers suitable for 16sqmm 4 ore XLPE insulated armoured cable tc coplete. Makes: SMI/Commet/Dowels

Supply and Transportation of outer dia 50mm and inner dia 38mm double walled corrugated HDPE duct made as per speacification BSEN-500 86/IS 1490 part-II with all accessories like couplers, bends, end caps, T's etc. , Complete. Makes:DURA LINE(Dura Guard)/Bajaj(ELEC-4.8.1)

Supply and fixing of Suitable out door feeder piller box of size made with 14SWG CRCA sheet with double door arrangement, making powder coating after processing of 7 Tank Process lock and key , hinges, rubber gasket , danger board , suitable angle iron stand for mounting the feeder pillar with cement concrete , including supply and fixing of Legrand DX3/Scheneider-Acti9 make 40A-63A, 4 pole MCB as incomer, 6 Nos 6-32A SP MCB's as out going, indication lamps, din channel, 6 sqmm 3 core copper cable for individual light control, connectors, gland plates and provision for 3 phase energy meter etc., completed for finished item of work and suitable wiring provision for connecting the nature switch. (ELEC-7.5.4(a))

Supply and Fixing of Automatic Street Light Control System with Optical Sensor, Low voltage /High Voltage trip and reset, operating voltage 150-280V AC per Phase, 50HZ with suitable SMC enclousure of IP 54 protection , MCB's of make Legrand DX3 and contractor suitable to control the load of 12KW of Three Phase load with necessary clamping arrangements. Makes: Swadeep Nature Switch

Supply and laying of 40mm Nominal Bore Medium grade G.I Pipe( ELEC-9.4.15-d)

Providing independent earthing for important equipment with 40mm dia 'B' class 2.5m long G.I pipe and 19mm dia 'B' class G.I pipe of 0.3mtr long conneted with reducer providing G.I funnel with mesh enclosed in CC brick Massonry chamber of 450m x 450m x 400mm with R.C.C slab cover duly providing staggered holes filling with 20Kg salt and 40kg Charcoal or 40Kg bentonite powder from the bottom of the pipe giving earth connection from electrode through G.I strip of 40 x 6mm x 200mm length with all accessories and labour charges complete, as per IS specifications 732/1982 (Part II)

Earthwork excavation in soils upto SDR by mechanical means for foundations of structures as per drawing and technical specification including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing sides of bottom, back filling the excavation earth to the extent required etc., complete excluding seignioarge charges for finished item of work as per MoRT&H specification 304(5th Revision) and as directed by the Engineer-in-Charge.

Providing PCC M15 mix using 40mm, 20mm & 10mm size HBG crushed stone aggregate and fine aggregate(Natural sand 50%+Manufactured sand(Rock Sand)50% ) conforming to table 1000-2 of MoRT&H including cost, conveyance of all materials to site and labour charges, centering, machine mixing, laying, Vibrating, curing etc., including all other incidental and operational charges of all T&P etc., complete for finished item of work as per MoRT&H specification 1500,1700, 2100 (5th Revision) and as directed by the Engineer-in-Charge for foundation.

Supplying, fitting and placing of HYSD bars Fe-500 ( From Primary producers ,Like TATA,SAIL,VSP, JWS & Shyam steel Etc.,) of different diameters, wrought and put up bars of all diameters including cost and conveyance of steel to site and all labour charges for fabrication of reinforcement including cutting, bending, binding rods, tying grills, placing them in position etc., complete including cost and conveyance of binding wire and all handling charges and operational charges etc., and including over lapping welding if required etc., complete for all R.C.C items for finished item of work as per standard drawings, as per the directions of the Engineer-in-Charge and as per MoRT&H specification 1600 &2200 (5th revision) in sub-structure.

Reinforced cement concrete M15 grade K.M stones of standard design as per IRC:8 fixing in position including painting and printing, etc as per drawing and Technical Specification Clause 804 MORTH ,including overhead charges & Contractors profit ,But Exculding Seignarage charges. Ordinery KM Stone

Reinforced cement concrete M15 grade H.M stones of standard design as per IRC:8 fixing in position including painting and printing, etc as per drawing and Technical Specification Clause 804 MORTH ,including overhead charges & Contractors profit ,But Exculding Seignarage charges. H.M Stone (200M) Stone

Providing and fixing of typical CRR informatory and Name Board with necessary Logo as per specifications and drawing. Three MS Plates of 1.6 mm thick, top and middle plate duly welded with MS flat iron 25mm x 5m size on back on edges. The lower plate will be we welded with MS angle irone frame of 25 mm x 25 mm x 5 mm. The angle iron frame of the lower most plate and flat iron frame of middle plate will be welded to 2 nos. 75 mm x 75 mm of 12 SWG sheet tubes posts duly embedded in cement concrete M-15 grade blocks of 450 mm x 450 mm x 600 mm, 600 mm below ground level. The top most diamond plate will be welded to middle plate by 47 mm x 47mm of 12 SWG sheet tube. All M.s. will be stove enameled on both sides. Lettering and printing arrows, border etc., will be pointed with ready mixed synthetic enamel paint of superior quality in required shade and colour. All sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing clause 1701 MORD ,including overhead charges & Contractors profit ,but excluding Seignarage charges.

Providing and erecting direction and place identifications of semi reflective sign boards as per IRC:67 made of 2 mm thick M.S. Sheet duly stove enameled paint in white colour in front and grey colour on back with red reflective border of 70 mm width and required message, letters, figures with reflective engineering grade tape as per MORD specifications of required shade and colour. supported and welded on 47 mm x 47 mm of 12 SWG Square tube of 3050 mm height duly strengthened by 25 mm x 5 mm M/s flat iron on edges on back firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as per drawings and Technical Specification Clause 1701 MORD.,including overhead charges & Contractors profit ,but excluding Seignarage charges.

Providing and fixing of semi reflective cautionary, mandatory and informatory sign board as per IRC:67 made of 1.5 mm thick MS Sheet duly stove white colour in front and gray colour on back with red reflective border of 65 mm width and required letters and figures with reflective tape engineering grade as per Clause 1701.3.9 of MORD for Rural Roads of required shade and colour supported and welded on 47 mm x 47 mm 12 SWG sheet tube firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as per drawings and Technical Specification Clause 1701 MORD ,including overhead charges & Contractors profit ,but excluding Seignarage charges.

Cost, supply and fixing on road of Reflective Studs - RMP (Twin Moulded Shanks) including cost and conveyance and all labour charges and including contractors profit & Over head charges, but excluding GST etc,. Complete.

Cost, supply and Painting on road of Thermoplastic Paint of 2.50 mm thick including cost and conveyance and all labour charges and including contractors profit & Over head charges, but excluding GST etc,. Complete.

Cost, supply and Painting on road for Rumble strips 7.5mm thick (in 3 layers each of 2.5mm thick) including cost and conveyance and all labour charges and including contractors profit & Over head charges, but excluding GST etc,. Complete.